I am facing a weird problem with my IMATE JASJAM USB Data Cable. When I connect the phone, it starts charging but on pc this error comes Unknown Device and drivers are not installed but it keeps on charging.
I don't have a genuine data cable, I have bought 3 different local made usb cables and with all three I face this problem.
Before I had a genuine cable but now it is not working, I don't know what is the problem, but is this a problem with my phone or with the cable?
If you use Windows XP do you have Activesync installed?
Download ActiveSync paa jee
Agreed with previous 2 dudes, it looks like you don't have ActiveSync installed.
I am not that n00b activesync is installed on my laptop and PC as well. Laptop has Vista and PC has XP.
Related
Running Schap's 4.01
It was syncing perfectly and for some reason it wont do anything via usb other than charge!
There is no connection notification from windows when I plug the unit in, in hard reset mode the coloured RGBW screen says serial not usb as other times.
It syncs fine via bluetooth.
I've unticked "advanced" in usb sync options and still nothing.
Any ideas?
A windows driver maybe?
eat this:
http://www.thbi.de/de/downloads/killassetupde.zip
Peer guardian blocks all USB connections
Are you running Peer Guardian on your comp by chance?? If so, it blocks the phone from syncing via USB but bluetooth still works. If you are running PG2 jsut run Task Manager and close it then connect
No I'm not running peer guardian.
I am running vista though. Thanks for the replys guys, appreciate it.
Anyone else?
sounds like a driver problem then. Go to Device Manager and When you connect your Hermes see what appears and delete the driver for it, then disconnect then reconnnect and itll install a driver for it, then check for updates with windows update and there should be an updated driver for it..download and install it, reboot and try again.
I'm running Vista and had to do that a couple of times when I had the same problem you are.
make sure also that you have usb connection enabled in in device settings in windows mobile device center.
Well bugger me it was the cable!
It was a car usbcharge cable and guee what....... it had no tx-rx connections!
My TP2 (vodafone) has decided it doesn't want to connect via USB any more. I have tried different USB leads, and verified it's not that by using other devices. I've tried different USB ports on my desktop (Windows 7 RC 7100) and also tried my laptop (XP) neither of which want to connect.
I've checked the USB to PC section in settings and tried it as both Activesync and disk drive, and with and without the 'enable faster data synchronization' box ticked, and soft reset after changing each setting. but every time the computer just won't recognise that I have plugged a USB device in.
Any suggestions?
No one have any ideas on this? I've tried a hard reset now in desperation, and it still doesn't seem to work.
PC does not recognize TP2 connection
Same problem for me; the TP2 is not recognized by the PC (or laptop)
Is there no program to check this? Otherwise.......I have to send for warranty repair.
Anybody any idea??
I have the same problem.
I can't get the device to connect to my PC by USB. It charges through the PC USB lead though.
What did you end up doing? Is it time to make a warranty claim?
I'm not sure if it applies to your situation, but for the longest time I could not get my Kaiser to sync with my laptop (which I usually kept wifi off on).
Turns out ActiveSync was out of date and didn't work since I had upgraded to WM6.1. If you're up to date already that probably doesn't help, but I thought I'd toss it out there.
just to let you know, i returned my tp2 to vodafone and the replaced it. the new one worked fine as soon as i plugged it in to the usb. so that proved it had to be a hardware fault.
i'm not sure if this is the right section to ask this but my tilt 2 is not recognized by my computer anymore. I thought maybe it is the phone but it's recognized on other computers so I was wondering is there a way to reinstall the driver on my computer or some other fix someone know of?
I think I saw some threads with similar problems but I didn't see any definitive answer in any.
HELP PLEASE!!!!!!!!!!!!
stevenmc8602 said:
i'm not sure if this is the right section to ask this but my tilt 2 is not recognized by my computer anymore. I thought maybe it is the phone but it's recognized on other computers so I was wondering is there a way to reinstall the driver on my computer or some other fix someone know of?
I think I saw some threads with similar problems but I didn't see any definitive answer in any.
HELP PLEASE!!!!!!!!!!!!
Click to expand...
Click to collapse
Do you have XP or Vista/7? The first step you should try is uninstalling/reinstalling whichevery type of sync software you have on the PC...for XP it's ActiveSync, for Vista/7, it's Mobile Device Center. A fresh reinstall of those sometimes clears this problem up, and it's the easiest solution to try first
I have xp and I have uninstalled and reinstalled but that doesn't do anything my phone still isn't recognize that's why I was wondering if after u uninstall does the driver remains on the hard drive and if so how would u remove the driver so u can reinstall it.
Do you use the same cable when you are connecting it to the other computers? If you do then... well I dont know.. I would still try a new cable and wiggle it a bit
When you uninstall the Active Sync I believe it does take the driver off as well...
When you connect your phone to the computer does it still come up asking if you want to connect via Active Sync, Disk Drive, Internet Sharing?
I'll give you one method that helped me at least when I was having connection issues, have no idea if it is related to yours (and it might not even be applicable to the older XP version of ActiveSync).
While your phone is connected, go into Device Manager and under the Network adapters node, look for "Microsoft Windows Mobile Remote Adapter". If it is there, uninstall it.
After that, disconnect then reconnect your phone.
As a long shot, you would not happen to be running any VPN software would you? A connected VPN always makes syncing the phone impossible.
Is your phone charging while connected?
I had/have a USB connection issue with my Tilt2. It wasn't recognized by the computer, but it was charging. When I connect through bluetooth, it is detected just fine. I am assuming that my issue are the pins in the USB connector on the phone, since I have the same issue with different cables.
Aaron McCarthy said:
When you connect your phone to the computer does it still come up asking if you want to connect via Active Sync, Disk Drive, Internet Sharing?
Click to expand...
Click to collapse
No the only thing it does now is charge.
MooGoo said:
I'll give you one method that helped me at least when I was having connection issues, have no idea if it is related to yours (and it might not even be applicable to the older XP version of ActiveSync).
While your phone is connected, go into Device Manager and under the Network adapters node, look for "Microsoft Windows Mobile Remote Adapter". If it is there, uninstall it.
After that, disconnect then reconnect your phone.
As a long shot, you would not happen to be running any VPN software would you? A connected VPN always makes syncing the phone impossible.
Click to expand...
Click to collapse
I will try what u suggested. no i don't have any vpn software installed on my computer anymore.
jcterry said:
Is your phone charging while connected?
I had/have a USB connection issue with my Tilt2. It wasn't recognized by the computer, but it was charging. When I connect through bluetooth, it is detected just fine. I am assuming that my issue are the pins in the USB connector on the phone, since I have the same issue with different cables.
Click to expand...
Click to collapse
yeah it's still charging but that is it... nothing else happens
Every so often when I connect my phone to my pc all it does is charge.. All I do to fix it is soft reset the phone AND restart the computer. Usually after that it works fine. If not just take it off and put it back on the dock or cable.. if you try a different cable that might work for you too. Or try plugging your cable into a different usb port on the computer
Already tried reformatting Windows and installing any and all drivers I could find.
When I connect my EVO to my PC via the USB cable, the connection type window appears, the amber light turns on, and it shows up on my PC for ~2 seconds. Then it disappears. I have been unable to keep it connected.
It works on other PCs I've tried, just not mine for some odd reason. (Any other USB item works fine), and I've tried multiple USB ports.
Any ideas?
I had this exact issue when I was going through a non-powered USB hub. As soon as I plugged it into my computer's direct USB plug no issues. How old is the computer you are trying to plug this into? Is is USB 2.0? I'm on windows 7 64bit if that helps. Hope you get this fixed, it's annoying as hell.
Forgot to mention, this is on Windows 7 x64 as well.
Im using the ports on my mobo, and its a rather new mobo (XFX 780i). Tried every single port =\
I've had this phone for about 4 months and it was working perfectly, flashing ROMs left and right. Yesterday I tried connecting my Samsung USB cable into my laptop and tried to hop on that USB storage. What my laptop is telling me when I connect it is strange. It says that it doesn't recognize the USB device. I tried re-installing the drivers, shutting both phone and laptop down and restarting.. nothing seems to work. Please help me, because without being able to connect to the laptop, my phone is going to be boring and unflashable. Thanks!
thenicksherman said:
I've had this phone for about 4 months and it was working perfectly, flashing ROMs left and right. Yesterday I tried connecting my Samsung USB cable into my laptop and tried to hop on that USB storage. What my laptop is telling me when I connect it is strange. It says that it doesn't recognize the USB device. I tried re-installing the drivers, shutting both phone and laptop down and restarting.. nothing seems to work. Please help me, because without being able to connect to the laptop, my phone is going to be boring and unflashable. Thanks!
Click to expand...
Click to collapse
I've had this happen before with my first sgs2, i'm on my third now. Try it on another PC, with another cable, if that doesn't work I'd just send the unit back for a replacement because the USB port is probably malfunctioning.