Related
I don't know if it's coincidence, but ever since I upgrade to WM5 and went back to WM2003SE, my navigation button has not worked the same.
For example, a lot of times I can go right, but can't go back left even after multiple presses, and then most of the time the middle or 'Enter' button doesn't do anything. Itz become extremely annoying because I have lost my 4th stylus by now, and I haven't received my new ones yet. Oh, and I can't play MorphGear right anymore.
Is it just hardware? Cuz I first went to ROM v.1.42 and then went to 1.40 to see if it was a problem with the new ROMs, but I still have the same problems. Any one else having these issues, and has any one fixed it??
UPDATE: WTF!! Now it went from bad to worse. Yesterday, when I left my BA at home, once I returned from work I noticed that PIE was constantly opening over and over again. Then some of the buttons wouldn't respond like the POWER to turn it off. The backlight pretty much stayed lit the whole time because it looked like the keys were stuck. I upgraded to WM5 derived from the Himalaya today and now the START menu comes up almost every 5-8 seconds, followed by a real quick succession of multiple "clicks", and my 'Start' button doesn't seem to be responding.
Can anyone help? Has my BA gone to the state of retardation? Is there a way to bring it back??
How did you go with this problem.
Mine is doing similar ever since a low battery problem.
DLC
I am experiencing the same kind of problem... and it happend after upgrade to WM5. But the problem likely to be caused by hardware.
I had problems with my phone opening up the start menu, opening IE, and closing programs immediately after opening them, Of course I had dropped the phone halfway in a cup of ice water, but immediately after tossing it in water (after hanging up, I simply dropped the phone into the cup-holder I have mounted below my stereo which happened to be occupied by a glass of ice-water I placed there without remembering) I shook the water out of the phone, and for about as much as i could stand the heat, I put a hair-dryer to the end of my phone which i pryed open after removing as many screws as i could. After a day of quirky behavior, and a night of having the battery seperated from the phone, my phone is back to its old self with the water-damage seal unnaffected after missing the line of water by just a few milimeters. I suggest going to Settings>Buttons and making every button perform no function at all followed by going to Settings>System>Button Lock and having all keys locked except your power button. Hope this helps!
Having somewhat the same issue. Only the "Down Navigation button" isn't working. Although, I'm still using Windows Mobile 2003 SE. Is there a DIY fix for this?
bump...
any suggestions?
Navigation Up/Down
Mine isn't working either - is this a hardware fault?
trying pressing down a bit harder. coz when i did that for mine, the "down" button works. normal applied pressure as for the rest of the buttons(left/right/up) does not seem to work with the "down" button, but a bit more force would make it work.
this happens to my IIs.. mebbe u can try.
Button problems
After no trauma or dunks in water several of my buttons have gone awry. My green phone button, red phone button and navigation buttons all open contacts. The green phone button activates voice command at the same time that it opens contacts. I've never switched from WM2003SE. I've checked the buttons settings and they are the same as always. Most bizarre of all is that my battery is quickly discharging. I suspect some software process is running hard but don't have any idea where to start to fix this. Soft resets have not helped.
buttons gone crazy
A hard reset fixed the problem but was a typical pain to get everything back going. Sprite backup works great until the first attempt to ActiveSync with your PC.
Hi Guys.
I've had my orbit for about 3 weeks now, and its been perfect. I had a spare 512mb microSD card lying about so I used that, but my 2Gb microSD card came in the post yesterday.
I put the card into the phone, and then plugged the phone into my computer via USB. The screen turned off, and no matter what I did, it wouldn't come back on.
I reset it using the small button on the side (sticking my stylex pen into it) and it restarted itself, showing the splash screen no problem, but as soon as you would expect the Today screen to show, the screen goes off. It get's weirder, because if I hold down the camera button to turn that on, the screen switches itself on, and you can use the camera no problem. If i hit the windows key, the menu appears, but if I try clicking an icon, the screen goes dead again.
Also, sometimes (not always, don't ask why) if I leave it for a couple of minutes, the screen slowly appears, as if the backlight is very very dim. But the second i tap anywhere, or touch a button, it goes off again.
I can still answer calls, and my alarms still go off. The phone seems to work perfectly, but just not the screen. I think that it might be the backlight having been turned so far down its off, but I don't know how I would go about reseting that.
Sorry for the long story, but any help would be greatly appreciated.
Cheers
have you tried to make a hard reset?
Man I had the exact sane issue. Its to do with the backlight. I had to angle the screen to try and see anything on it, then changed the backlight to full and made sure it didnt switch off after certain time, everything fine since then. dont know how it happened.
exactly like fubofo wrote,try to unplug,screen should be visible again, check backlight prop.-and plug it in.
i have the same problem this appears sometimes.I think this is a damn bug that appears randomized.It happend to me like 6 times.I have the o2 xda orbit with german o2 rom.What's about yours? it dims the light under the normal makeable settings this sucks.And the camera works because the light settings goes automaticly to the highest settings in camera mode.
Hi guys,
I remember having that problem but it was when I tried some programs, including HTC X-button and another called Invisible Shooter. I haven't got any further incident after uninstalling them.
Do you think what you've encountered with may also link to some program you've installed?
BUSPBP
Totally confirmed! Had same issue after replacing a touch screen. Thanks, guys, for a clue!
Hello,
Can someone help please, I’ve overclocked my Qtek S200 (Prophet) to such a speed that my phone is not capable to run on.
The difficulty is, before I have done this I foolishly “Registered” in start-up menu for the overclocking software to run at 288 MHz.
Now when restarting, the phone is reaching a point of Window Mobile and then it’s either stops dead or restarting it self constantly.
I can guess the solution but don't know how to do it I need somehow to stop Overclocking software to be used during a boot up.
Or maybe even a hard-reset. (I did that already but it’ freezes at the point where I can see 3colors on the screen and nothing further. Any suggestions please?
The easyest way is to perform a Hard Reset. Make sure you have the power button, the camera and the comm manager button pressed while reset ing the S200. The other way is to take a look at the startup folder and see if there's a program that is automaticaly launched on startup that changes the speed of the device. The only thing you have to do is delete that entry...
Hope it helps.
RE: SOS
I did try it to do hard reset the way you said, in the end this really helped.
I removed the battery and left it for about an hour. Then plugged my USB cable, done what you normally do on Hard Reset, by pressing Photo button on the side and Comm. Button and pushed the pen. When phone stopped at the point where I could see 3 colours, at the bottom USB text appeared. I re-install new ROM and magic! My phone is back from the dead
i've just updated the ROM on my artemis, after CID unlocking etc. It was working fine, although it seemed to occasionally power off whilst copying files to it via AS. Thinking it was the SD card I removed it, and now it won't turn on. Plugging into power for a few mins gives a red light on the top, but I can't power the thing on.
Anyone want to give me some tips on what I can do to rescue it?
Download this HTC P3300 WWE factory rom here http://rapidshare.com/files/19322112/HTC_1.12.405.01_026790_WWE_SHIP.rar . Now first launch Bootloader (multi color screen) and just run the ROMUpdateUtility.exe from the rar, voila your device unbricked .
Bootloader: Press voice dialing & on/off button at the same time till you see a multi color screen (red/green/blue stripes)
landwomble said:
i've just updated the ROM on my artemis, after CID unlocking etc. It was working fine, although it seemed to occasionally power off whilst copying files to it via AS. Thinking it was the SD card I removed it, and now it won't turn on. Plugging into power for a few mins gives a red light on the top, but I can't power the thing on.
Anyone want to give me some tips on what I can do to rescue it?
Click to expand...
Click to collapse
Your mobile is actually turned on but backlight is set to lower so your screen does not appear. It 's a known bug changing backlight by itself. It happened to me too with Β&Β4 when I enable Batery Status tray Icons. And happened again on B&B 4.3 twice with no reason and Thanks God not to lower setting.
You have two options (both painfull).
1. Hard reset.
2. Reflash.
Good Luck
i thick it's easyer than reflash or hard reset, just plus the artemis to a usb or to the charger and your screen bright will be at full bright. Once done that, simply adjust the bright when running with battery at control panel.
moonshadow88 said:
i thick it's easyer than reflash or hard reset, just plus the artemis to a usb or to the charger and your screen bright will be at full bright. Once done that, simply adjust the bright when running with battery at control panel.
Click to expand...
Click to collapse
This did not work for me before. I hope you are more lucky.
nor for me - it's dead
freco said:
This did not work for me before. I hope you are more lucky.
Click to expand...
Click to collapse
I'm presuming that it's not actually related to the flash, until proved otherwise though - no-one else has reported any issues and as it was a 2nd hand but new to me handset it seems more likely it already had a fault. Annoying, though.
Ric
my friend had a similar problem with his charmer, although h never cooked it.
if you are in london, go to southall, they will fix it for £20
try plugging in to the charger if the little orange light comes on, its a phone fault, if the little light doesnt come on, your phone is not holding charge, either way can be fixed
Orbit cannot be switched on, and cannot be charged
patterns said:
my friend had a similar problem with his charmer, although h never cooked it.
if you are in london, go to southall, they will fix it for £20
try plugging in to the charger if the little orange light comes on, its a phone fault, if the little light doesnt come on, your phone is not holding charge, either way can be fixed
Click to expand...
Click to collapse
Hi, I'm having a similar problem as you described. When the charger is plugged into my Orbit, the little light does not come on. Moreover, when try to switch my phone on, it turns on and starts booting. But before it could boot further than the O2 splashscreen, it shuts off. Occassionally, I do succeed in turning it on, which it would turn it itself off at random from a few mins to a few hours after turning the phone on. I'm able to access the red, green, blue screen without any problems, and it can be turned on (ie the phone remains in the red, green blue screen) indefinately untill the battery runs out. I've tried re-flashing with the O2 official WM6 (which i was using for a few months already) which didn't make a difference. I'm able to access the phone through activesync just fine, but it wouldn't charge throughj the USB connection as well. I'm currently charging my battery with my friends Orbit.
Would any guru have any clue on what's going on with my phone? Can it be fixed?
I have a HTC Tilt 2... I have been having a ton of problems with this phone but when it really freaks out, I usually take the battery out, let it sit a few days and then it starts working again. My phone started doing some funny things today so I restarted it as usual, it freezes and I remove the battery. When I turned it back on I got a red, green, blue and white screen with text:
RHOD300 32M MI-BC
SPL-0.87.0000
MicroP(LED) 0x0A
MicroP(KEY) 0x04
TURBO HW/TURBO SW
TP MFG DATA
498, 526 792,855
795,211 214,211
223,845 Calibrated
This has never happened before.
This RGB&W screen used to say serial when it first happend a few hours ago but then I installed ActiveSync and plugged it into PC, now says USB.
ActiveSync won't recognize my device, it does appear in My Computer.
I tried following directions in another forum to turn the device off then hold the pickup/hangup/power button at the same time...a different screen appeared than the forum directed, a gray screen with "Trigger Ramdump Mode"...then I couldn't do anything.
I can restart it back into the tri-color screen...
I need help in laymen's terms. I've never tried to change anything about the phone's operating system, I've never done an update or anything, I do not have the Tilt2 CD.
Right now I have my SIM card and my SanDisk card removed, I was afraid it could get erased when I tried the pickup/hangup/power button trick.
PLEASE SOMEONE HELP!!!!!!!!!
This screen is called the bootloader. Its used by technicians (or more advanced users) to load the OS or "ROM" onto the phone. It may be stuck in bootloader because some of the OS files are damaged or missing, and the OS is not booting up. Or possibly even a hardware failure.
Pulling the battery may/may not be the culprit. I've read someone on here mention that pulling the battery can corrupt files on the phone. If the phone is lagging, frozen, then pulling the battery is not the correct way to restart the phone. The correct method of restarting the phone by soft reset is done by sticking the stylus into the small red hole/button on the side of the phone, while the batter cover is off:
http://www.hardreset.eu/htc_touch_pro_2_rhodium_hard_reset_soft_reset_en.html
Pulling the battery is only a method of last resort, as the soft reset button will work in almost all cases.
Hard reset by holding TALK, END and POWER is probably not going to work. It requires the OS to be working, and you are not even getting to the point that the OS is booting.
Its supposed to say "USB" when the phone is connected to your PC via the USB cable. If I remember properly, it will say "Serial" in bootloader for a second when you plug the phone to USB, and switch to saying "USB" after that. USB is a form of serial connection, after all (USB = Universal Serial Bus). As long as it says "USB", you are in somewhat good shape, since it SHOULD allow you to try the following.
Try downloading the latest ROM from HTC. This is actually a newer version than the ROM that was originally on your phone, but still "official" ATT software. And by most accounts, better than the old ROM. Since its official software, installing this will not endanger any warranty you may still have on the phone.
Its the first file on the following page ("ROM Update"):
http://www.htc.com/us/support/tilt-2-att/downloads/
With your phone connected to your PC by USB, run the .exe ROM update file and follow the instructions that come up on your PC screen. It should work. Try it and let us know.
Bear in mind, you will lose any personal data you have on the phone (contacts, texts, emails, etc). But you've probably already lost those.
Its possible there is some other way out of it, I certainly don't know all the tricks. But in searching around this site, being stuck in bootloader seems to require flashing a new ROM to get out of it. And it seems that you are prepared to lose your personal data, based on the fact that you were already trying to hard reset (the TALK, END, and POWER button process) which also dumps all your data. And flashing the official ROM is really pretty easy to accomplish. Just a pain that you have to re-setup the phone again, since it will basically be returned to factory condition (but in this case, a slightly newer version of the OS).
The SAME thing happened to My HTC Tilt 2 an Hour ago (1/13/2010 4:46pm)
The same exact thing occurred to my HTC Tilt 2 today. It is stuck on the red green, blue and white screen with the same yellow 'config' type message . The white bottom strip has the black letters "serial" typed in.
My problem also, is that the phone stays "on" until i pull the battery out. The moment i place the battery back in the phone, the keys stay lit up instantly and the screen is black. When pressing the power button, then i get the same red, green, blue and white screen.
Ive tried holding the talk/end/power buttons all at the same time, it doesnt make a difference. So i cant get to the step where you press the "volume up" key so to initiate the master reset.
Ihad no idea the HTC Tilt2 would just fry like this. I had no additional apps that were unusual to the norm, i even had more free space than used on the set. its not like the phone was over loaded.
Hmmmmm.... help!!!
Re-read above about "soft-reset" and you might want to try reflash your phone.
Sent from my MSM using Tapatalk
RicoATT said:
The same exact thing occurred to my HTC Tilt 2 today. It is stuck on the red green, blue and white screen with the same yellow 'config' type message . The white bottom strip has the black letters "serial" typed in.
My problem also, is that the phone stays "on" until i pull the battery out. The moment i place the battery back in the phone, the keys stay lit up instantly and the screen is black. When pressing the power button, then i get the same red, green, blue and white screen.
Ive tried holding the talk/end/power buttons all at the same time, it doesnt make a difference. So i cant get to the step where you press the "volume up" key so to initiate the master reset.
Ihad no idea the HTC Tilt2 would just fry like this. I had no additional apps that were unusual to the norm, i even had more free space than used on the set. its not like the phone was over loaded.
Hmmmmm.... help!!!
Click to expand...
Click to collapse
Read my post above. Your OS is missing or damaged, and you need to reflash (re-install) it.
Master reset re-loads the OS from the ROM area of your memory. The ROM is damaged, so their is nothing to reload. That's why its stuck in bootloader (tri-color screen).
redpoint73 said:
Read my post above. Your OS is missing or damaged, and you need to reflash (re-install) it.
Master reset re-loads the OS from the ROM area of your memory. The ROM is damaged, so their is nothing to reload. That's why its stuck in bootloader (tri-color screen).
Click to expand...
Click to collapse
_______________________________________________________
Today, i stuck the battery in the phone (Tilt2) pressed the hard reset keys. THIS time it allowed the volume-UP key to finally kick in the reset to default cycle. I got the phone working again and have restored my last backup So, I havent lost anything.
The only problem now i am noticing is the light on the keyboard never goes off. Even when I power the phone down, "the keyboard stays lit".. I am having to remove the battery just to keep it from draining when the phone is not in use.hmmm. is there a regEdit key I can modify that may turn off the keys? id rather have no light at all over no battery juice. If i can edit the key to turn off the backlight on the keyboard permanantly , this will be a temp fix for me until i get a new phone.
as anyone ever experienced this?
RicoATT said:
_______________________________________________________
Today, i stuck the battery in the phone (Tilt2) pressed the hard reset keys. THIS time it allowed the volume-UP key to finally kick in the reset to default cycle. I got the phone working again and have restored my last backup So, I havent lost anything.
The only problem now i am noticing is the light on the keyboard never goes off. Even when I power the phone down, "the keyboard stays lit".. I am having to remove the battery just to keep it from draining when the phone is not in use.hmmm. is there a regEdit key I can modify that may turn off the keys? id rather have no light at all over no battery juice. If i can edit the key to turn off the backlight on the keyboard permanantly , this will be a temp fix for me until i get a new phone.
as anyone ever experienced this?
Click to expand...
Click to collapse
_______________________________________________________
Well, today 1/18/2011: the above issue seem to have vanished altogether. Very good. I did nothing but what i was resolved to do until I buy a new phone (take the battery out so to completely power down the phone and lights).
Today, my ole third hand decided to work like normal! Yay!. All of a sudden it rebooted, and now the keyboard backlight turns off when the keypad is closed and you can see it light up when extended. and most importantly: the back lighty for the keypad goes "off" when the phone is powerd down. go figure this one.
I am glad its working like normal now, but i know its time to get a new phone. These are just symptoms of the "big-crash" soon to come. I am backing up every day.
For now, very very glad my phone is back to "normal"