I don't know if it's coincidence, but ever since I upgrade to WM5 and went back to WM2003SE, my navigation button has not worked the same.
For example, a lot of times I can go right, but can't go back left even after multiple presses, and then most of the time the middle or 'Enter' button doesn't do anything. Itz become extremely annoying because I have lost my 4th stylus by now, and I haven't received my new ones yet. Oh, and I can't play MorphGear right anymore.
Is it just hardware? Cuz I first went to ROM v.1.42 and then went to 1.40 to see if it was a problem with the new ROMs, but I still have the same problems. Any one else having these issues, and has any one fixed it??
UPDATE: WTF!! Now it went from bad to worse. Yesterday, when I left my BA at home, once I returned from work I noticed that PIE was constantly opening over and over again. Then some of the buttons wouldn't respond like the POWER to turn it off. The backlight pretty much stayed lit the whole time because it looked like the keys were stuck. I upgraded to WM5 derived from the Himalaya today and now the START menu comes up almost every 5-8 seconds, followed by a real quick succession of multiple "clicks", and my 'Start' button doesn't seem to be responding.
Can anyone help? Has my BA gone to the state of retardation? Is there a way to bring it back??
How did you go with this problem.
Mine is doing similar ever since a low battery problem.
DLC
I am experiencing the same kind of problem... and it happend after upgrade to WM5. But the problem likely to be caused by hardware.
I had problems with my phone opening up the start menu, opening IE, and closing programs immediately after opening them, Of course I had dropped the phone halfway in a cup of ice water, but immediately after tossing it in water (after hanging up, I simply dropped the phone into the cup-holder I have mounted below my stereo which happened to be occupied by a glass of ice-water I placed there without remembering) I shook the water out of the phone, and for about as much as i could stand the heat, I put a hair-dryer to the end of my phone which i pryed open after removing as many screws as i could. After a day of quirky behavior, and a night of having the battery seperated from the phone, my phone is back to its old self with the water-damage seal unnaffected after missing the line of water by just a few milimeters. I suggest going to Settings>Buttons and making every button perform no function at all followed by going to Settings>System>Button Lock and having all keys locked except your power button. Hope this helps!
Having somewhat the same issue. Only the "Down Navigation button" isn't working. Although, I'm still using Windows Mobile 2003 SE. Is there a DIY fix for this?
bump...
any suggestions?
Navigation Up/Down
Mine isn't working either - is this a hardware fault?
trying pressing down a bit harder. coz when i did that for mine, the "down" button works. normal applied pressure as for the rest of the buttons(left/right/up) does not seem to work with the "down" button, but a bit more force would make it work.
this happens to my IIs.. mebbe u can try.
Button problems
After no trauma or dunks in water several of my buttons have gone awry. My green phone button, red phone button and navigation buttons all open contacts. The green phone button activates voice command at the same time that it opens contacts. I've never switched from WM2003SE. I've checked the buttons settings and they are the same as always. Most bizarre of all is that my battery is quickly discharging. I suspect some software process is running hard but don't have any idea where to start to fix this. Soft resets have not helped.
buttons gone crazy
A hard reset fixed the problem but was a typical pain to get everything back going. Sprite backup works great until the first attempt to ActiveSync with your PC.
Related
The keyboard on my TP2 (Verizon) intermittently stops working (no key press registers, however the buttons on the face of the phone still do). After soft reset it works again. This is with different ROMs. I'm thinking, perhaps, there is a loose connection internally. It also has odd crashes, but this might only be a ROM problem as it is much less pronounced with the latest ROM I'm using (Elite team ROM).
Diagnosis? I'm reluctant to send it into Verizon for just this, as its only occasional. Wondering if anyone has experienced the same thing
I'm having this same exact issue. I'm using the latest ROM from HTC. Sometimes when I open the keyboard in an app, like texting or email, the keyboard is genreally non-responsive. When it's in this state, the enter key goes to windows Apps but all other keys failed to work. I also test by pushing the FN to see if the FN light tunrs on.
What's strange with mine is the keyboard will work when it's open like for phone use, but when open with an app like text/email/bing, it doesn't...
Like previous poster, not sure if hardware ro what...
This may not have anything to do with your problem, but..
I have the PTT button on my tilt2. I have a case that wasn't designed to encompass that button, so it gets covered up (I had a find time finding a case that did actually fit!)
I have the PTT button assigned to do nothing, but with it being pressed down, it makes my keyboard non-responsive as well as disabling the arrows keys on my touchscreen. It will however work for a while after restarting my phone, but it always goes back to the same thing.
Sukuiku said:
This may not have anything to do with your problem, but..
I have the PTT button on my tilt2. I have a case that wasn't designed to encompass that button, so it gets covered up (I had a find time finding a case that did actually fit!)
I have the PTT button assigned to do nothing, but with it being pressed down, it makes my keyboard non-responsive as well as disabling the arrows keys on my touchscreen. It will however work for a while after restarting my phone, but it always goes back to the same thing.
Click to expand...
Click to collapse
Thank you very much for posting this. I do have the same exact setup, I have the PTT button unassigned and I too have a cover that covers it. So maybe it's pressing it down causing the problem.
I hope this is it and really appreciate your post...
UPDATE:
Sweet, I just checked things out. removed the cover and it would the keyboard doesn't go non-responsive when I push the PPT button, and works when I don't...
By George, I think you got it!!!!
GREAT!!!!
Hello boys
from about 1 week i have this problem on my device, if i have the keyboard out and write an sms or typing an url when slide the keyboard in the device automatically reset itself...
anyone knwo this problem or the solution ?
Thanks for the help
Nicola
Hi,
I have a problem with my keyboard too, I've searched the forum but i didn't see the same problem as i have or the solution. My phone's screen turns off when i slide out the keyboard. Actually phone stays on but the light of the screen goes off. when i slide it out i'm able to write something or make calls. when i slide it back, screen keeps itself off and i press the sleep key "2 times"!(screen looks like off but it isn't) to reopen it again. I press the sleep key for the first time to turn the screen actually off, and press it one more time to turn it on again. i did a soft and a hard reset to the phone, didn't solve it. I don't think it is a software problem but i hope it is
img714.imageshack.us/img714/167/70305198.png
These are the photos of the occasion.
The screen keeps itself on until the end of the slide. it turns off then. when I slide it back, i can see the backlight of the screen and the light of the buttons.( i don't think that you would see it on the photo, 3rd photo).
I'm waitin for your help guys, thank you so much.
Isn't there anyone to help my problem? I'm waiting for your answers..
I'm also having this same issue. When I slide the keyboard in it just turns off sometimes. At first I thought it might be a physical issue with the internals of the phone and the sliding impact of the keyboard was causing it to reset, but it doesn't do it all the time for me. I can jam on it and nothing happens sometimes, or other times it resets from a gentle nudge. I am running Energy GTX from August 26 or 28, whatever version that was.
I also have this issue now where my end key is unresponsive. Doesn't. Work. Ever. and that is so freaking annoying. If anyone has any insight here PLEASE share it.
Thank you.
Wow i just saw your message and suprised. Is that my phone you're using? Because I have that end key problem too. It works when I press too hard. And I have 3rd problem now. I think my phone's microphone is not working. People i'm talking on the phone is always complaning about that they can not hear my voice or it's too low. Now I have three problems:
1. Phone is turning itself off when i slide the keyboard out.
2. End key is not responsive.
3. Microphone is low or its broken..
Maybe reflash your phone to origional rom.
I was using WM 6.5 without hardspl when the problem occured. then i did hardspl and installed custom roms, i even tried with WM 6.1. It didn't help about any of it. I'm used to not using the keyboard actually, but the problem with microphone is annoying..
Same problem with the keyboard
gurcanmerdal said:
Wow i just saw your message and suprised. Is that my phone you're using? Because I have that end key problem too. It works when I press too hard. And I have 3rd problem now. I think my phone's microphone is not working. People i'm talking on the phone is always complaning about that they can not hear my voice or it's too low. Now I have three problems:
1. Phone is turning itself off when i slide the keyboard out.
2. End key is not responsive.
3. Microphone is low or its broken..
Click to expand...
Click to collapse
I have the same problem !!!! Did you manage to resolve because I am sure this is software relatred. I had android on my phone prior to this and fixated that the issue is coming from this
Had the same keyboard issues, found that it was a battery issue. when you shut the phone, the battery would loose connection.
bluewaterkayak,
more info on the loose battery connection.
i have the same problem with sliding the keyboard down and the screen turning off. closing it, pressing the sleep button 2x, turns the phone back on. i can slide the keyboard down just enough and hold it to type out a text, any more and it'll go off.
THIS IS SUPER ANNOYING
Bumpski. Really need this fixed.
What ever you last installed take it off. If not you might have to go factory restore
It's definitely not a software issue. The screen itself somehow gets disconnected when slid up all the way.
Took it apart and found nothing obvious wrong. Is there something to look at exactly when the slider is at the end of it's travel? The cables seemed fine. The problem only happens at the end of travel.
I cleaned the slider area and pried some contacts down. Nothing. Put it back together and same problem.
Ideas??
See here:
http://forum.xda-developers.com/showthread.php?t=561151
Tried the fix posted in the last link with Kapton Tape.
Didn't work.
Any ideas?
I have the same issue. My old VZW TP2 is sitting in a drawer in my house because people kept saying they couldn't hear me on the other end. Also on my new one, when i slide the keyboard in/out sometimes it turns off, not always though. I figured it has to be a hardware issue as well, if i do it slowly nothing happens but if i just slide it open and let the springs kick in, it usually cuts off once it 'snaps' to the end of the sliding path.
Initially when pressing the back button on my desire, a large majority of the time, it would register it correctly (i.e. do the operation associated with the back button), irrespective of my finger placement as long as I apply a low amount of pressure.
Now, I find that a lot more key presses on the back button are lost. I have to press much more harder / deeper to improve the chance the keypress registers. This is the second time I've encountered this and the third hardware fault I've had:
Fault #1: headphone jack not working, music continues to play through speaker (repaired)
Fault #2: back button doesn't always register key presses (repaired)
Fault #3: back button doesn't always register key presses (going to have to be repaired again, sigh).
I've searched the forums but haven't found anyone else mentioning this problem. Has anyone else experienced this issue at all? Or have I got crummy luck and gotten an HTC Lemon?
I have the exact same thing. Only started recently though. It takes a hard press sometimes, and other times if I press hard it's like a double button push.
You aren't alone. Lol
Cheers rolfd. Least I know I don't have the "touch of death".
It's definitely fixable cos I've handed it in for repair and it's come back working. My concern is more if it continues to re-occur. Guess I'll have to wait and see...
You are not alone about this problem:
http://forum.xda-developers.com/showthread.php?t=778793
Both mine Menu and Back is not working properly. Got send it in for service and still havent get it back yet.
*Update* My phone got repaired.
Back button now works as expected. Fingers crossed it stays that way...
Everytime I boot my phone up, it works fine up until when the screen goes into sleep mode. Once it goes into sleep mode I cannot turn the screen back on, it stays black. The keyboard, end and answer key lights show up when I press the power button but the screen just stays black no matter what button I press.
I end up having to either take the battery out or using the stick to press the reset button on the side in order to get the phone to where I can see the screen again. I have adjusted the settings to where the screen doesnt go into sleep mode and the screen just stays on but that drains my battery. I want to be able to have my screen go off so I can save power but if it goes off it wont come on again until I reboot.
I have done a hard reset. This problem started happening to me when I started using the Energy Rom but I've even flashed different Roms and the problem still exist.
Somebody please tell me what's wrong! I need help! This is a big annoying problem to have. Thanks.
is this problem occurring when you slide the keyboard out?
i had the t-mobile touch pro2 with this problem.
the screen would die when the keyboard was out and not come back.
if this is the case, what i did was...
well. obviously not open the keyboard fully.
but if i accidentally had.
instead of pulling out the battery, i waited...
till the screen 'naturally' went to sleep.
than i would pull out the stylus or press power button
and the screen would come on.
sh4d0w86.
sh4d0w86 said:
is this problem occurring when you slide the keyboard out?
i had the t-mobile touch pro2 with this problem.
the screen would die when the keyboard was out and not come back.
if this is the case, what i did was...
well. obviously not open the keyboard fully.
but if i accidentally had.
instead of pulling out the battery, i waited...
till the screen 'naturally' went to sleep.
than i would pull out the stylus or press power button
and the screen would come on.
sh4d0w86.
Click to expand...
Click to collapse
Yes the problem still exist even when I slide the keyboard out. Once the screen goes off, that's it....pressing the power button to get it out of sleep mode, sliding the keyboard, I press all buttons and nothing works. The only thing that "works" to get the screen back on is removing the battery or using the stylus to press the reset button.
When sliding the keyboard out the keys light up but the screen doesn't come on, also pressing the power button lights up the end and answer keys without the screen coming on.
themasterhook2000 said:
Yes the problem still exist even when I slide the keyboard out. Once the screen goes off, that's it....pressing the power button to get it out of sleep mode, sliding the keyboard, I press all buttons and nothing works. The only thing that "works" to get the screen back on is removing the battery or using the stylus to press the reset button.
When sliding the keyboard out the keys light up but the screen doesn't come on, also pressing the power button lights up the end and answer keys without the screen coming on.
Click to expand...
Click to collapse
so. whenever the screen goes out, period, you cant get it back?
or the screen goes out and cant get it back once you slide the keyboard out?
if it is only when sliding out the keyboard...
try not opening the keyboard fully on the right side.
on my rhodium, after that point, the screen goes out.
sh4d0w86.
sh4d0w86 said:
so. whenever the screen goes out, period, you cant get it back?
or the screen goes out and cant get it back once you slide the keyboard out?
if it is only when sliding out the keyboard...
try not opening the keyboard fully on the right side.
on my rhodium, after that point, the screen goes out.
sh4d0w86.
Click to expand...
Click to collapse
Yes, period. Also, you know when you put your face to the phone during a call and the screen goes off so your face wont press anything on the screen? It doesn't come back on from that either once I end the phone call, it just stays black. I'm assuming you don't have any other suggestions. This Sucks
themasterhook2000 said:
Yes, period. Also, you know when you put your face to the phone during a call and the screen goes off so your face wont press anything on the screen? It doesn't come back on from that either once I end the phone call, it just stays black. I'm assuming you don't have any other suggestions. This Sucks
Click to expand...
Click to collapse
: / sorry. i am unsure.
maybe you have a lose connection?
sh4d0w86.
This has to be a software issue but I don't know where to start. I'm surprised nobody else has encountered this problem. I've grown frustrated of this issue because I don't understand why it's doing this. I have had the phone for almost 6 months only dropping it once 4 months ago and it wasn't a strong damaging drop that would affect anything inside. I guess I'll just have to go last resort and call warranty to swap the phone out. Thanks for the help.
Same problem
themasterhook2000 said:
This has to be a software issue but I don't know where to start. I'm surprised nobody else has encountered this problem. I've grown frustrated of this issue because I don't understand why it's doing this. I have had the phone for almost 6 months only dropping it once 4 months ago and it wasn't a strong damaging drop that would affect anything inside. I guess I'll just have to go last resort and call warranty to swap the phone out. Thanks for the help.
Click to expand...
Click to collapse
My phone also dos not come back on, when I put it in out the sreen with the power button on top, or when the phone goes to sleep. Nothing can put it back on(opening te keyboard, pulling out the stylis, presing the answer-, windows-, back- and end button). I and up using a music players too keep the phone busy what's makes it operational. Cant really remember when this started happening exactly. My phone is at the moment loaded with a standard ROM. I used too have a custom ROM.
My TP2 does this too, although I only encounter the problem sometimes when someone calls. I answer and put the phone next to my ear, the screen goes black as it should and the phone just dies. I can't hear what the other person is saying and the screen wont turn on anymore. I have to take out the battery to reboot.
set light sensor to manual in settings. You have some bad or fragmented code causing the problem. Pretty common actually, many different reasons, but usually either a bad light or proximity sensor or software issue. Setting the sensor to manual should do it, if not, hard reset and allow the phone to fully set up before touching it, to allow full customization process to complete. Search my posts on SOD (sleep of death) for more information.
Funny this was brought up. Now im worried I just dropped 250.00 and have a new one coming.
Mine started with the ear piece quit working. couldnt hear anything except on speaker.
Anyway I started having the screen issue over a month ago, only way to get it back was soft reset with the stylus. Also when the screen was lit, I couldn't hit the power button to turn the screen off. At times the screen would be on 24/7 and I just dealt with it. The times when it decieded to go to sleep was when I needed the soft reset. Well long story short I forgot my charger one day at work and the battery died. after pressing the power button for hours with no response, moving the screen in all diffrent directions as I pressed the button.It came on once after hrs of messing with it. Well today it died again and I am fed up with it so out came the tools. Once I opened it up I noticed the ribbon that feeds the screen from the mother board was worn and torn. the ribbon slides everytime the keyboard is slid out and it rubs on both sides of the phone. I thought maybe mine was just a fluke and was installed wrong considering the phone being 10 months old but now I read this and see maybe its a common problem. The cheapest I could find the Ribbon was 56.00 so I didnt want to chance it not being the issue.
Hi everybody,
I have sometimes a strange problem :
- the volume down button doesn't work anymore.
- I can't use the power button to turn on / off my phone, but it works as I can press it 3 times to open camera. On the contrary, I can't use it to ask for reboot, but it works for soft reset! Aaaaaarrgh! Brain pain!
When I try to soft reset, my phone enters in safety mode, as if I pressed the volume down button during restart.
In bootloader, I can't use power and volume down button. Quite annoying.
Sometimes, volume is turning down without pressing any button.
But what is weird is that my phone shifts from normal state (all buttons working) to defect state and back to normal state again without doing anything. It's unpredictable. It can work well for decades, then stops working fine for hours or days then back to normal.
Sometimes, when it works well, when I'm using it, it goes wrong without doing anything. I'm reading my favorite site and volume is suddenly going down. Without warning, without even touching a button.
I have to say one more thing. I picked up that phone from a coworker, and the volume button is a bit bent near volume up (picture needed?) but it worked fine for months before starting to mess.
I hope you'll be able to help me.
Sorry for my English, it's not my native tongue.
Seems to me like a hardware problem.
What I'd do honestly is to hit it repeatedly on a hard surface, but please, do not do that
If you can I suggest taking it apart and making sure all the ribbons are firmly set in place and undamaged. It can be an one way ticket for damaging the phone for good though, so wait for other suggestions too.
Thanks for your answer.
What is making me angry is that it also does this when left alone on the table : I let it there working perfectly and when I pick it up again, it fails.
And when it fails, once again I let it alone and suddenly the volume goes down, without even touching it. Raging.
its a hardware problem, u have to change the volumes and power flex, had the same problem with the powern button, i turn the phone off, and a few secons later it power on by himself till i change the flex
Did you take the phone apart recently? I had my battery replaced and that's when my Volume up started phantom pressing. I hit the phone repeatedly on a flat service and made sure to kind of slap it so it would impact kinda evenly as to not dent the case, it worked for about a week at a time, then I just took the phone apart and tried to align everything and made sure all the insulation tape was flat and and not bunched up and now it's fine. We'll except my USB port has got some giggle to it. Order a new USB of amazon for like $9, I'm trying to hold out for a LG V30