Help why my activesync cant connect with my PPC?
Thanks
Did you use xp sp2 and activesync 4?
I used to have ActiveSync 4.0 problems too... Device manager detected the device but failed to install driver.
In my case it started working once I swaped the cradle's USB connector to another USB jack with the PDA in the cradle.
Windows XP found the "new" device and installed properly this time... Now I can Synch fine through USB.
Also some say that you need to change something on you PPC, so go to Start/Settings/Conenctions/Network Cards and select "Remote-NDIS Host" and change it to "Server-assigned IP address" and then Ok, Ok, Ok...
I hope this helps you...
Rayan
Hi all,
I was trying to upgrade my Qtek9000 with an official ROM Updater, but my device went immediately into the Serial bootloader mode and I've not been able to do nothing to run out from this mode...
I've tryied the solutions suggested in http://forum.xda-developers.com/showthread.php?t=290234 without any luck...
The problem is that neither Mtty nor the UNI_exitbootloader tool are able to connect to USB.
I'm using no usb hub, I'm running on a Dell Precision M90 notebook, I've disabled USB connection in Activesync (4.2.0) and also tryied with a pc without activesync installed.
Any idea?
Thanks
Paolo
Are you on XP or Vista, and what version of AS/WMDC do you have?
Hi,
I'm running Xp, ActveSync is 4.2.0, don't know what WMDC is sorry, can you please explain?
Don't worry about WMDC - it's only relevant if you have Vista.
Are you using the proper cable that came with the Universal? Some cables don't have all the pins wired. That (or a broken USB port) would explain why your Universal isn't going to USB mode when you plug in the USB cable. Have you looked carefully to see if it changes from saying "Serial" to "USB" at the top of the Bootloader screen when you plug in the cable?
If it does change to "USB", I would try upgrading to ActiveSync 4.5 - go to http://www.microsoft.com/windowsmobile/activesync/activesync45.mspx
Make sure you disable USB Connnections in the Connection settings before plugging in your Universal. Then try flashing the CE ROM again.
Good luck
BTW did you try doing a hard reset to get out of bootloader (both soft keys and then the reset button, then select 0).
Good advice, especially with upgrading to AS 4.5, it's a full release now on Microsoft Update site, and I have a feeling the WM6 ROMs may require it... Good luck with it, keep us posted.
Ok, thanks all!
This morning I connected the PDA to my office's PC with it's original cable and it instantly switched to USB mode...
So, I launched the upgrade and it's now in progress... let's hope!!!
It might really be a cable problem, yesterday night I tried with 2 different PC and a not original cable (I think it's my camera one...)
Thanks a lot, by now... I'll let you know own this story will end...
Ok, new ROM is up and running!
Thanks all!
Bye
Paolo
Good stuff.
Dear All
I have a very strange problem here...i was using the Jwright WM6 rom till this morning with no sccuess in getting it to connect to my Vista laptop by all means...the only thing i could do is to connect to my desktop pc which has Windows XP & it connects succefully...so i thaught it's something related to the crossbow not being compatible with vista WMDC
Till this morning a friend came to me with his Universal running Jwright 1.90.96 WM5 to install a program so i connected to the Vista WMDC & it worked like a charm...so i downgraded mine to the same WM5 version he is running & i was shocked when it didn't connect & kept trying to connect till it gave me red error sign with no explanation
I used the same USB port, the same original cable on the same laptop under the same windows user...
Any explanation for that????!!!
I really need to sync with my vista laptop as it's my main PC at both work & home...
Thanks All
Hi there Guys
I am using Windows vista with with Windows Mobile device center installed on it. However when I connect my mobile to the pc a message comes up and says device malfunctioned.
When I change the usb port it works but it does not connect with the WMDC.
I thought Vista might be the problem and Used an XP computer with Active Sync on it but It does not work.
So what Shall I do please reply quickly
Thanks
Dear Sirs;
Maybe this part of forum not be the proper place for my question but I don't know the poeple more expert than XDA masters.
Since last monday, computer cant recognize my Diamond when I connect it by USB cable and "USB device not recognized" appears. I will be really appreciated if you kindly help me.
Best Regards
Dariush Chegini
Try reinstalling Active Sync/Windows Mobile Device Center.
First remove Active Sync/ WMDC, restart PC and than install Active Sync/ WMDC.
Thanks for your kind attention. I reinstalled Activesync...no change, computer can't recognize the Diamond. My Diamond charges with both charger and computer, USB headphone works but PC can't recognize it....
I'm so confused and will be really appreciated if XDA masters help me.
Best Regards
XP or Vista or Windows 7 or which OS?
I've tried by both WIN XP and Vista.
could be a few possibilities for XP atleast...
activesync - file->connection settings->allow usb connections checked
faulty cable, try another one
faulty port on computer, try another one
driver issue - a difficult one...
i had this on my xp, found out there's something wrong with the cable - phone charging fine via computer USB, but XP says it doesn't recognize the device so doesn't connect to activesync....
good luck
Try on your Diamond -
Start>Settings>USB to PC
Unchek "Enable faster data synchronization"
If none of the above solutions work, maybe a hard reset...
I tried another cables, all options in "USB to PC", Activesync options, hardreset, even install other ROM but PC still can't recognize the Diamond.
It seems to be a Hardware problem but Diamond can be charged by USB and USB headphone works properly... I'm so confused .
Thanks Millions
Dariush
dchegini said:
I tried another cables, all options in "USB to PC", Activesync options, hardreset, even install other ROM but PC still can't recognize the Diamond.
It seems to be a Hardware problem but Diamond can be charged by USB and USB headphone works properly... I'm so confused .
Thanks Millions
Dariush
Click to expand...
Click to collapse
Try this in order...
1. Connect diamond to pc - it should at least charge as your say, but not detect Activsync
2. Goto Settings > Connections > USB to PC
3. Check Allow USB Connections > Uncheck allow fast data sync...
Does it connect?
if not and if you are using Vista
1. goto Windows Mobile device Center
2. check the attached image to see you have the same settings...
Does it connect?
if still not, then it could be driver issues, which I can suggest, once you reply to the above...
Thanx for your attentions. I've tried uncheking the said bottom but no change.
I used to connect the Diamond to the same notebook without any problem for more than 16 months, but the damn notebook stop recognizing my Diamond these days .
Thanks Millions
Dariush
may be usb port on your computer is malfunction. Did u try different usb port?
You need to open device manager in control panel to see how you diamond is listed.
Ever since i started with a new company 3 years ago they have some software that prevents activesync from connecting to any device I have from their computers using USB.
I went Bluetooth method and all is fine. I just use the USB for large, direct file transfer to internal storage.
If you get issues with activesync and usb and can take ages to resolve (if possible).
I guy's.
After a lot of search in this forum and a lot of other forum's, i came to this threat.
I had the same problem, my diamond didn't connect to my pc.
I had tried all the different suggestion, and nothing seemed to work. until i read the post of cloudedhopes, that suggested to change the usb cable. Because it was the only thing that i hadn't tried, i did change the cable, and it worked!
So i'm posting only to thank you guy's for all of the help, given not directly to me, but to all user!