Related
Hi,
Since AS 4.2 came out I have problems to use USB Internet passthrough in Activesync, als AS 4.5 did not solve this problem. I googled around a lot and also searched in xda forums but everyone is giving other instructions, some say this, some say it the other way. It also does not depend on the rom, I had the same problem on the wizard and now also with my TyTN on wm5 and wm6 roms.
So my question is: How to enable USB internet passthrough on ActiveSync 4.5? At the moment my desktop activesync is set to "automatic" in the connection settings, and on my device under Settings->Connections->Connections->Advanced->Select Networks I have "Orange Internet" as the connection which connects to the internet (which has in the proxy settings "this network connects to the internet" enabled). and the work connection is "My ISP" which has no settings at all. I tried to add a new network connection but didn't even know which Modem I have to choose and so I gave this up.
I also tried to set my desktop activesync to either use "Work" or "Internet" instead of automatic but when I try to use Opera, Internet Explorer or any other program like downloading the weather data all programs say that the host or page cannot be found or report a network error.
Can anyone help with this, I'm really very desperate... Cause I also tried to find the correct settings for hours now, but without luck...
Thanks for any help with this subject.
marcelser said:
Hi,
Since AS 4.2 came out I have problems to use USB Internet passthrough in Activesync, als AS 4.5 did not solve this problem. I googled around a lot and also searched in xda forums but everyone is giving other instructions, some say this, some say it the other way. It also does not depend on the rom, I had the same problem on the wizard and now also with my TyTN on wm5 and wm6 roms.
So my question is: How to enable USB internet passthrough on ActiveSync 4.5? At the moment my desktop activesync is set to "automatic" in the connection settings, and on my device under Settings->Connections->Connections->Advanced->Select Networks I have "Orange Internet" as the connection which connects to the internet (which has in the proxy settings "this network connects to the internet" enabled). and the work connection is "My ISP" which has no settings at all. I tried to add a new network connection but didn't even know which Modem I have to choose and so I gave this up.
I also tried to set my desktop activesync to either use "Work" or "Internet" instead of automatic but when I try to use Opera, Internet Explorer or any other program like downloading the weather data all programs say that the host or page cannot be found or report a network error.
Can anyone help with this, I'm really very desperate... Cause I also tried to find the correct settings for hours now, but without luck...
Thanks for any help with this subject.
Click to expand...
Click to collapse
do you use a proxy server for this pass through connection? what activesync partnership do you have setup "Guest" or a Normal one...
First to be able to use passthrough you must be connected to your PC via USB and thus connected to active sync. Active Sync should be fully set-up.
First question;
Can you synchronize your data through Active Sync 4.5.
If yes. Try to tick all the items in the desktop active sync> connections settings. On the space "this computer is connected to" select automatic
second: Can your PC connect to the internet?
If yes open the PC Internet Explorer and try to browse, then, while connected at USB, open Pocket Internet Explorer in your mobile and try to browse. You should be connected to the internet then. Good Luck!!
If still you wouldnt connect there must be wrong on your Active Sync partnership set-up
Two more tips:
1. Start/Settings/Connections/USB to PC - untic
2. http://pdaphonehome.com/forums/552203-post22.html
no proxy
walshieau said:
do you use a proxy server for this pass through connection? what activesync partnership do you have setup "Guest" or a Normal one...
Click to expand...
Click to collapse
I don't use any proxy server for connecting to the internet, my PC is directly connected to a NAT Router, as well as my linux box and my girlfriends computer and all work perfect.
As for the activesync partnership, where do I see the type of my partnership or in other words, what is a "guest" partnership? The only thing I see is that my device is named "WM_marc1" and that activesync items sync perfectly but the internet passthrough won't work.
I hope you can give me further advice with this information. Thanks for you help
docles2002 said:
First to be able to use passthrough you must be connected to your PC via USB and thus connected to active sync. Active Sync should be fully set-up.
First question;
Can you synchronize your data through Active Sync 4.5.
If yes. Try to tick all the items in the desktop active sync> connections settings. On the space "this computer is connected to" select automatic
second: Can your PC connect to the internet?
If yes open the PC Internet Explorer and try to browse, then, while connected at USB, open Pocket Internet Explorer in your mobile and try to browse. You should be connected to the internet then. Good Luck!!
If still you wouldnt connect there must be wrong on your Active Sync partnership set-up
Click to expand...
Click to collapse
My data synchronizes perfectly through AS 4.5 and I have already checked all items in connection settings. Of course my computer is connected to the internet (see reply to walshieau) and honestly IE and pocket IE have nothing to do with internet passthrough, it's all about TCP/IP subnetting, bridging, tunnelling or whatever method AS 4.5 uses for internet passthrough.
Sorry if i am not explicit...but i hope this helps. For my wizard i remember i had to install a reg on the PC. It did some changes to the Active Sync registry.
The bad is that i don't have that reg
marcelser said:
Hi,
Since AS 4.2 came out I have problems to use USB Internet passthrough in Activesync, als AS 4.5 did not solve this problem. I googled around a lot and also searched in xda forums but everyone is giving other instructions, some say this, some say it the other way. It also does not depend on the rom, I had the same problem on the wizard and now also with my TyTN on wm5 and wm6 roms.
So my question is: How to enable USB internet passthrough on ActiveSync 4.5? At the moment my desktop activesync is set to "automatic" in the connection settings, and on my device under Settings->Connections->Connections->Advanced->Select Networks I have "Orange Internet" as the connection which connects to the internet (which has in the proxy settings "this network connects to the internet" enabled). and the work connection is "My ISP" which has no settings at all. I tried to add a new network connection but didn't even know which Modem I have to choose and so I gave this up.
I also tried to set my desktop activesync to either use "Work" or "Internet" instead of automatic but when I try to use Opera, Internet Explorer or any other program like downloading the weather data all programs say that the host or page cannot be found or report a network error.
Can anyone help with this, I'm really very desperate... Cause I also tried to find the correct settings for hours now, but without luck...
Thanks for any help with this subject.
Click to expand...
Click to collapse
hi, I am using wm6(LVSW series, black Series and now Official Dopod release) on my hermes, everytime I can successfully connect to the internet via activesync using whatever program like pie, opera, spb insight, weather update, WML etc.
what I have done is simply unchecked the 'enable advanced network functionality' under start -> settings -> connections ->USB to PC and then plug the usb cable to my pc.
I use activesync 4.5.
hope this help
ctrlaltdel said:
hi, I am using wm6(LVSW series, black Series and now Official Dopod release) on my hermes, everytime I can successfully connect to the internet via activesync using whatever program like pie, opera, spb insight, weather update, WML etc.
what I have done is simply unchecked the 'enable advanced network functionality' under start -> settings -> connections ->USB to PC and then plug the usb cable to my pc.
I use activesync 4.5.
hope this help
Click to expand...
Click to collapse
YES WORKS UNDER VISTA TOO
simply check the 'allow data connections on device when conneted to the pc' under connection settings and then plug the usb cable to pc.
Heres the Fix
I had the same problem and this reg key fixed it for me 100%
Download this file AND RENAME IT TO lspvalue.reg
the double click on the reg file on your PC
Jules
ZaJules said:
I had the same problem and this reg key fixed it for me 100%
Download this file AND RENAME IT TO lspvalue.reg
the double click on the reg file on your PC
Jules
Click to expand...
Click to collapse
That's the one i was talking about, thanks i was going to need it too
Ok followed the procedures. I think anyone of them works. Mine worked by changing on PC activesync to "this computer is connected to: The Internet". Nothing else worked. I had the reg hack from the time of my beloved Wizard!
go to:
start -> settings -> connections -> advanced -> select network
make sure that
"programs that automaticaly connect to the internetshould connect using"
"my work network" and not "my isp"
then go to
start -> settings -> connections -> usb to pc
and make sure to uncheck "enable advanced network functionality"
that should do it
regards
H.S.
hsalah72 said:
then go to
start -> settings -> connections -> usb to pc
and make sure to uncheck "enable advanced network functionality"
that should do it
regards
H.S.
Click to expand...
Click to collapse
on my hp 6828, it doesnt seem to have the usb to pc option/icon.
tried the first part selecting connect to work.
I'm stil haveing a problem. any ideas?
maymaymay said:
Two more tips:
1. Start/Settings/Connections/USB to PC - untic
Click to expand...
Click to collapse
This one works for my TP
Goshh... I love this board !!
Thank you very much, maymaymay
Still not working
Why can't someone come up with an ACTUAL solution to this?
When I connect my Tilt to the PC it automatically passes the internet connection through the PC. I did the registry fix and tried all four settings (0, 1, 10, 11) and still my data connection on the phone is overridden by the active sync desktop pass-through. I turned off the advanced networking option and still it goes through the PC. I even went through all the settings in active sync for "This computer is connected to" even though that doesn't even look like it would affect which connection my phone uses. This seems more like a setting within active sync on the phone more than anything.
I use my phone at work for chatting on yahoo IM (with Palringo) since my company network is filtered. I use a program called MyMobiler to transfer the phone display and controls to the PC so I can use my desktop keyboard for the chat program instead of my phone's keypad. Since the network is filtered the internet connection on my phone is filtered too since it's passed through the desktop when I active sync it to use MyMobiler. Sometimes Palringo will hold the connection even after I've connected to the desktop and sometimes it won't.
Bottom line here is can someone come up with an real working solution to this problem that a LOT of people are having?
HOW TO DISABLE DESKTOP PASSTHROUGH WHEN CONNECTING WITH ACTIVESYNC. Search that on google and here and all you will find are people saying "Yeah I have that problem too" or people telling how to connect WITH desktop passthrough.
I have a similar issue. I have my phone connected to my work PC to charge / sync, but all Internet connections attempted by the phone are being routed through my work network until I unplug the USB.
Naturally, that's very bad since all Internet traffic is logged by my work and many sources are blocked. I have an unlimited data plan on my phone. Why can't I stay connected to it when I'm hooked to ActiveSync?
I read someplace that Windows Mobile has an order of preference where connections are concerned. Probably hard line, then wi-fi, 3G and then EDGE. Surely there must be some way to modify this order of preference.
The thread is missunderstood...
The problem here is give to the PPC internet via usb... providede by a PC...
The solution that REG (that works for me EVER!!!).
And now other one provide internet to my PC via usb on phone account
With apologies, I'm not sure I understood what you said there.
But, some of us are actually trying to stop receiving internet by the USB.
I would like the phone to initiate a wireless 3G connection even when connected to the PC. But, thus far, all settings I've tried still cause my phone to attempt to access my business network here at my company.
Big no-no.
have you finally solved the problem?
If so just like to ask if you have change your homepage in ppc? which is
file://windows/default_0409.htm?
and have not run your network wizard? then maybe I have the solution here
Reg key
HKEY_LOCAL_MACHINE\Software\Microsoft\Internet Explorer/AboutURLs/
usually it is ( default value )
A.Blank value is res://webview.dll/blank.htm
B.Home_0409 value isfile://windows/default_0409.htm
C.version_0409value isfile://windows/default_0409.htm
if there is a new reg in that one try to delete that file again using a registry explorer ( depends on what you use to view the file)
turn it off for about 30 secs then soft reset... I hope this helps out
I'm not sure that addresses the issue, or mine at least. My phone disables HSDPA the moment I plug the USB cable into the phone and Active Sync takes over. It's before I even open a browser.
Not only does the phone start looking for Internet over the USB Active Sync connection, it looks for non browser related things like weather updates and sending mail to the gmail server.
Somewhere, it's coded to have an order of preference in what kind of connection it accesses. By default, it seems to look for any available land line connection, possibly wi-fi next, then 3G and then EDGE. I'd like to take the land line connection completely out of the equation.
I upgraded my Cingular 8525 today to Windows Mobile 6 with no problems that I can see except for one annoying thing.
When I have my device connected to my desktop, I get an error when trying to sync with my Exchange server.
I have my 8525 set up for Microsoft Direct Push. In the past, the 8525 would sync with Exchange through my computer and it's network connection. Now this not seem to work since upgrading to Windows Mobile 6.
===========================================
Many thanks to the folks who discovered this fix. You would think ActiveSync would have put this entry in itself. I was seeing both error code 85020006 and error code 80072f7d.
One simple registry edit and all is working perfectly. See below:
From: http://www.pocketpcfaq.com/faqs/acti...shoot-as4x.htm
#23 If you are using ActiveSync 4.2 and have a problem with Desktop Pass-through it may be caused by a Layered Service Provider (LSP) that use the Windows TCP/IP stack. This has been known to occur with ISA Server. The registry file LSPValue.reg will reverse this setting. Microsoft and the Pocket PC OEM does not support users that edit the registry.
http://www.pocketpcfaq.com/faqs/activesync/LSPvalue.reg
If you are using ActiveSync 4.2 and have a problem with Desktop Pass-through it may be caused by a Layered Service Provider (LSP) that use the Windows TCP/IP stack. This has been known to occur with ISA Server. The registry file LSPValue.reg will reverse this setting. Microsoft and the Pocket PC OEM does not support users that edit the registry.
RAlfieri said:
I upgraded my Cingular 8525 today to Windows Mobile 6 with no problems that I can see except for one annoying thing.
When I have my device connected to my desktop, I get an error when trying to sync with my Exchange server.
I have my 8525 set up for Microsoft Direct Push. In the past, the 8525 would sync with Exchange through my computer and it's network connection. Now this not seem to work since upgrading to Windows Mobile 6.
Any ideas are appreciated. I'm guessing it is another ActiveSync anomaly.
Regards,
Rob
Click to expand...
Click to collapse
just untick Enable advanced network functionality
/start/settings/connections/usb to pc/
Hmmm... I did and it still gives me the error. Code 85020006. Cannot connect with current connection settings. Microsoft Exchange - Attention Required.
Other ideas?
Regards,
Rob
This MAY help you:
right click on the activesync icon in your system tray (on the pc).....click "connection settings".
on the drop down menu titled "This computer connects to:" change this from automatic to "the internet", then apply the settings.
Cheers! Thanks for the suggestion. I got a different error now.
Synchronization could not be completed. Please try again later. Support Code: 80072f7d
You gotta' love it (or not)...
Regards,
Rob
Same Problem
I know this problem, but never found a working solution.
I can uncheck "Advanced Network Functionality", or change to "Work" under connection settings to succesfully sync with Exchange again, but thats not an option for me.
I want to have work and internet connection at the same time, because I also want to sync my IMAP account over the internet, and update my Weather Forecast automatically.
I know when I hard reset my device, it will work again, but I already did a clean install 1 week ago.
Who really knows why its working one day, and the next day it isn't working anymore???
I guess the problem occurs while using exchange-sync and IMAP at the same time. I had exactly the same problem. And in general, there is a problem with new ROMs since other users have to disable "advanced usb mode". That wasn't the case with older versions of WM6.
This helped for me:
1) Using Black Satin ROM
2) Do not use Schaps Advanced Configuration Tool
But my point is:
WHY is it working for several weeks, and then suddenly it STOPS working??
There must be an explanation isn't it?
It seems to be a problem with my PPC, cause when I perform a hard reset it will work again(but who knows for how long?)
Your link is dead
Pass Through Problem Solved
I upgraded my Dopod 838Pro to Windows Mobile 6 with no problems. Since then when I have my device connected to my desktop, I get an error when trying to sync with my Exchange server.
I used the following settingscombined and they worked GREAT!
- just untick Enable advanced network functionality/start/settings/connections/usb to pc/
- right click on the activesync icon in your system tray (on the pc).....click "connection settings". On the drop down menu titled "This computer connects to:" change this from automatic to "the internet", then apply the settings.
MCEITLIN said:
I upgraded my Dopod 838Pro to Windows Mobile 6 with no problems. Since then when I have my device connected to my desktop, I get an error when trying to sync with my Exchange server.
I used the following settingscombined and they worked GREAT!
- just untick Enable advanced network functionality/start/settings/connections/usb to pc/
- right click on the activesync icon in your system tray (on the pc).....click "connection settings". On the drop down menu titled "This computer connects to:" change this from automatic to "the internet", then apply the settings.
Click to expand...
Click to collapse
This works for me. Vp3G 3.0 Rom. I sync with 2 desktops as well as exchange. Although I'd get errors the sync would still happen for the most part. Now it's perfect though!
Great thread - very helpful.
help!!!
i cant sync with my pc....error no 85010014...
also i m nt able to upgrade my rom...whenever i select a ruu wrapper it says failed to initialize...sumone pls help on this...
thanks in adv
its showin the same warning"failed to initialize properly"
i tried variuos roms(shamanix,tnt,funkey's ,etc) but its still not workin...
guys i updated my .net framework n the roms r gettin updated but my sync still doesnt work
Just another data point... I had the same issue with my Mogul. I tried all the settings changes (Internet, Disable Advanced USB, etc, etc) Nothing worked until i read the MS thread and noticed someone got it working by turning on wifi and then turning it off. Worked for me also. Seems like some settings are getting cached somewhere....
Sorry for digging up and old thread, but I thought I would share something related to this subject.
I recently got a new Kaiser and Dell D830 laptop supplied by my work and was quite annoyed to be getting the 80072f7d error when syncing my exchange email via activesync while connected to my laptop with a USB cable.
I had came across the allowlsp registry setting which resolved the error, but since I was away on a 3 week work trip with nothing much to do, and not being happy about basically disabling a new 'feature' to make something work I was determined to get things working the way they should.
Going by the below articles I noticed that the registry entry either enabled or disabled Activesync desire to use LSP's (Layered Service Providers).
http://pdaphonehome.com/forums/sams...3050-activesync-4-2-internet-pass-thru-2.html
http://www.microsoft.com/windowsmobile/help/activesync/troubleshoot.mspx
As the first link clearly states, Activesync ability to use LSP's is a good thing:
This allows for improved compatibility in environments where connections to the internet must be passed through these LSPs
Click to expand...
Click to collapse
So in situations where one might be using their laptop in numerous different locations and on different networks (airports, hotels etc) we would want it left on.
As per the second link:
When other applications install additional LSPs....
Click to expand...
Click to collapse
It pointed to the fact that some other application installed on my laptop must be causing the problem.
A quick google on "Layered Service Provider" Dell found me an article on the Dell website mentioning that:
Some versions of the Wave software written for Dell include the file biolsp.dll that adds Wave's Layered Service Provider (LSP) to the Winsock catalog, which...htm Future releases of Wave software written for Dell will not include biolsp.dll.
Click to expand...
Click to collapse
So I figured...hmm...I have a bum LSP on my machine, and I have crazy pre-installed Dell software which uses one which is known to cause strange problems. A quick deinstall and reboot later and now Activesync is back working the way Microsoft intended...using LSP's but capable of syncing via pass-thru connection.
I'm happy to have found problem/cause/solution instead of a potentially problem causing workaround....and it passed an hour or two in a lonely Hotel room...win win
other solution
this was posten in on of other messages and it worked great for me...
Delete the partnership with Activesync then reconnect my device and it started working again.
(Make sure you phone is not connected to the USB)
Open Activesync --> File --> Delete Mobile Device
fix outlook, and advance options off did not help..
sadik007 said:
this was posten in on of other messages and it worked great for me...
Delete the partnership with Activesync then reconnect my device and it started working again.
(Make sure you phone is not connected to the USB)
Open Activesync --> File --> Delete Mobile Device
fix outlook, and advance options off did not help..
Click to expand...
Click to collapse
This fixed also my Problem with 80072f7d
Accessing & Using the internet via USB
I have an unlocked HTC S620 & TyTN (Hermes).
When I connect the TyTN to the USB I am able to browse the internet as the phone uses the PC as a gateway automatically.Even if I do not setup a profile for activesync and the software recognises the device as "Guest". I am ceretain that this is the case and not accessing the service via the carrier or WiFi as I have enabled flight mode and been able to use the internet on the TyTN, browsing, using IM+ Mobile Mesenger etc.
I do not find the same functionality with the HTC S620 (T-Mobile Dash). Does anyone know how to get this functionality going?
Usually you always need to make a partnership for internet pass through to work. Strange you don't with the Hermes.
indiekiduk said:
Usually you always need to make a partnership for internet pass through to work. Strange you don't with the Hermes.
Click to expand...
Click to collapse
When you say partnership I asume you mean bluetooth.
I Turned on Flight mode and diabled bluetooth on the TyTN, connected it to the PC. Activesync came on and I cancelled setting up a profile so it was registered as guest. I got internet access via the usb cable connected to the PC. The same is not working for the S620.
I guess the distinction between the two is the TyTN is a Pocket PC and the S620 is a smartphone. There are various Ethernet Miniport Cards available for configuration on the TyTN. You find these under Settings>>NetworkCard>>Network Adapters. The one I find that shows up as connected is IEEE 802.11b/g Compatible Wifi Adapter, this I find strange as the device is in flight mode. The S620 does not have all the features and configurable network adapters under settings. Simply put a smartphone will not have all the networking capability of the Pocket PC
Let me know your thoughts please, or if you have another solution.
Here is how I got mine working.
1) Connect phone to pc.
2) Make sure ActiveSync shows connected.
3) Under ActiveSync Window select File->Connection Settings...
4) Change the "This computer is connected to:" setting from "Automatic" to "The Internet".
5) Under you phone go to IE -> Menu -> Tools -> Options -> Connections and make sure "Automatically detect settings" is enabled.
That's it. You should now be able to browse the internet through your pc connection.
Forgot to mention I am using ActiveSync ver 4.5.
Dash Internet Sharing Files on S720
On my HTC S720, there was no Internet Sharing option, even though it is WM6 unit. So after reading lots of threads on here and hofo, found out Blackjack had similar issue, as well as some WM5 devices running AKU 3 or higher.
So I copied intshrui.exe, intshare.dll and intshrui.lnk from Dash WM6 Rom dump, created relevant registry entries as:
Windows Registry Editor Version 5.00
[HKEY_CLASSES_ROOT\intshruiapp]
[HKEY_CLASSES_ROOT\intshruiapp\DefaultIcon]
@="tapres.dll,-14294"
[HKEY_CLASSES_ROOT\intshruiapp\SelectIcon]
@="tapres.dll,-14295"
[HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Shell\Rai\:MSINTERNET_SHARING]
"0"="MSINTERNET_SHARING"
"1"="IntShrUI.exe"
"2"=dword:00000001
"3"=dword:00000000
[HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Shell\Rai\:MSINTERNET_SHARING\Session]
@=hex:00,db,4d,43,70,b9,c7,01
Then run intshrui.exe and while I can connect via Bluetooth PAN, I couldn't get any IP. I also tried a static IP and that didn't work as well. I investigated a little more, and found another key:
Windows Registry Editor Version 5.00
[HKEY_LOCAL_MACHINE\Comm\ConnectionSharing]
"DisabledOnBoot"=dword:00000001
"EnableAddressTranslation"=dword:00000001
"EnableDhcpAllocator"=dword:00000001
"EnableDnsProxy"=dword:00000001
"EnablePacketFiltering"=dword:00000001
"PrivateInterface"=""
"PublicInterface"=""
"SetLastDhcpAddrToIEH"=dword:00000001
[HKEY_LOCAL_MACHINE\Comm\ConnectionSharing\Driver]
"Dll"="ipnat.dll"
"Flags"=dword:00000002
"Index"=dword:00000000
"Prefix"="NAT"
Then I copied ipnat.dll to s720. Here is the interesting part. If HKEY_LOCAL_MACHINE\Comm\ConnectionSharing exists, intshrui.exe will not connect, it will briefly grey out and come back to disconnected mode. As soon as I delete the key, it will setup USB or BT PAN and wait for connection (left soft key turns to Disconnect). I don't even have to reset the unit while making change to this key. Also, I left the HKEY_LOCAL_MACHINE\Comm\ConnectionSharing as empty, and noticed as soon as I run intshrui.exe, it will populate
"PrivateInterface"=""
"PublicInterface"=""
keys under ConnectionSharing key. I also tried to change various reg keys, such as HKEY_LOCAL_MACHINE\Comm\Tcpip\Parms\IpEnableRouter to 1, and
[HKEY_LOCAL_MACHINE\System\State\Connectivity]
"InternetSharing"=dword:00000001
None helped as well.
Am I missing a file or reg key to make this work? I looked on my Dash for various keys/files but didn't see anything useful.
has anyone figure out how to get internet sharing on wm6?
Have a look at;
http://forum.xda-developers.com/showthread.php?p=1517183&posted=1#post1517183
I posted up the files and a .reg file taken from my WM6 Dopod 838, but I don't know if everything required is there. If anyone knows what else is required I'm happy to copy it from my device and post it here.
Would you mind posting ipnat.dll - it is missing from Blackjack II WM6..
Internet Sharing kavana's 080308
does anyone have a problem with Internet sharing?
Bluetooth PAN and USB sharing dosnt work for me with kavana's 080308 rom
and remade wm6.1 kavana's 080308.
Before I never had any problem with T-mobile, russian, rodger, HTC.....
skf said:
does anyone have a problem with Internet sharing?
Bluetooth PAN and USB sharing dosnt work for me with kavana's 080308 rom
and remade wm6.1 kavana's 080308.
Before I never had any problem with T-mobile, russian, rodger, HTC.....
Click to expand...
Click to collapse
I have fix this problem,and update XIP and SYS to 19202,i'll upload the new version later,just wait...
Thank you. I wait for new version .
btw With your rom I able to install and USE tomtom ,
with T-mobile Windows Mobile 6, I get incompatible with tomtom navigator arror.
http://forum.xda-developers.com/showthread.php?t=364685&highlight=tomtom
What's new in 080312:
Update to new kernel
Full English version
Fix Internet Sharing ----do not work for me ;(
6.1 Internet Sharing Problem *R.I.P.*
Has anyone figured out why Internet sharing NO LONGER works with any 6.1 roms that i flashed to? From Kavanas ROM s to Ricky's Remakes.
Is there a fix to this?
Can any of you "smarter" Gents or Ladies, look into this.
this is wierd. who is your operator? mine works just fine with the settings i use. maybe we should find out if this problem only exist for certain operators. might also have to do with the network connections on the pc. like i said in another post, i noticed a new network connection appears when you sync the phone, unlike in wm6.0. another thing is i would have problems with activesync everytime i flashed to a new rom without doing a uninstall & reinstall of activesync.
Se7eN43 said:
this is wierd. who is your operator? mine works just fine with the settings i use. maybe we should find out if this problem only exist for certain operators.
Click to expand...
Click to collapse
Shouldn't be operator issue. Worked great prior to updating to 6.1. (T-Mobile USA)
What rom are you using?
damn u were quick to respond. i edited my first post. im usin the new v15 rom. and tmobile is my operator.
ediit: i just messed with my settings and went back to how i had them before and now its not letting me do the internet share. hmm... this is not cool
Iv used V14, V8 and V5 and none of them allow my internet sharing to work. V5 worked at first but then stopped.
I really like 6.1 but I NEED that internet sharing
WHAT settings are talking of? that work for you?
INTERNET VIA USB PROBLEM SOLVED!!!!
ok i think the problem may be with activesync. like i said, in my second post edited, i had messed with the advance settings of connections menu, and reverted back and it stopped net sharin via usb. i noticed activesync gave me an error sayin somethin about not being able to fully connect but i was still able to browse my phone, also giving me a constant animation of the activesync icon, saying "connecting" never stopping when a full connection is establish. when i fixed this and the icon stopped turning and said "connected" i tried and it worked.
on a fresh install of the past couple of roms, this is what i did... (from an earlier post of mine)
this is what i did. use the "connection setup" in the accessories folder. choose country & operator. dont think it matters but i also selected "Enable Auto Configuration" under the menu.
in explorer, under "menu/tools/options/connections" Auto.Detect Settings is selected. under "Select Network" choose The Internet.
now go into ur phones "Connection" settings, select "GPRS". in my case, select, "T-Mobile WModem Link", under "Connects to", select The Internet. for other operators, guess look for somethin similar. now u should be able to share via usb.
one thing u might have to do is, delete whatever gprs settings u have now and power off and back on. then do the above.
sorry if this is so messy looking
Can you post the entry "seetings" for "T-Mobile WModem Link"
I manually entered my connections.
So i dont have the modem link
Hi,
I haven't managed to get BT internet sharing working between the TP2 and my laptop. I've been trying to create a BT personal area network that enables internet sharing. Whenever i select the internet sharing option, it claims my laptop doesn't support it.
This is bogus, because i had the same laptop with the same setup working just fine through my old Tytn II. You just enabled internet sharing and away you go! How HTC have managed to mess this up is baffling (and annoying!). Trouble is i need to route my laptop through my phone or it's not very useful.
Is there any way that is known to work?
Thanks for any ideas,
Don't know if this is feasible in your situation, but can't you just use the USB cable and ICS? Tethering through BT would be slower and less reliable than using the cable.
It is easy but I'm not sure if you aware about the new widcomm btooth settings applet. In the 3rd tab, select Networking Manager > Share Internet Connection > Follow On Screen > Done.
I am having the same problems and I have tried the network manager > share internet connection but no luck. what makes my case worse is that i have the Toshiba bluetooth stack. any ideas?
gotta try that with tp2 btw yesterday when i tried to send some files from tp2 to my old hermes (tytn) it didn't work because tp2 claims 'device does not support a suitable service to perform this operation'. however the bt-link between my lap-top and tp2 or tytn works fine and i have used the internet sharing many times with my old tytn
so maby the are some issues with the newer bt? dunno
Eureka! I have manged to get a connection and i am posting this over it. But I tried so many things that I am going to have to delete the connection and start all over again so I can create a step by step guide for anyone that may be intersted. Test enviroment is TP 2 WM 6.1 (obviously) and Toshiba laptop with Toshiba stack running Vista.
You have the same problem as i did if you will get the error msg 'remote device does not support bluetooth PAN' and have a toshiba bluetooth stack. I should be back soon. Wish me luck so I dont mess up everything.
1. Enable BT on TP2 and make device discoverable
2. On laptop right click BT icon --> options --> General --> select PAN networking service
--> yes --> ok.
3. On laptpp right click BT icon --> add new connection --> custom mode --> next --> select your TP2 --> next --> select group ad-hoc network --> next --> next --> finish.
4. On your device --> open ICS --> select bluetooth PAN --> select your PC from list of BT devices --> accept connection on PC.
You should be good to go at this stage cos it works for me. If you dont mind leaving the PAN networking icon on your taskbar then you only need to do step 1 and 4 anytime you want to share your internet connection otherwise it will be step 1, 2 and 4.
Good luck and I hope someone finds this useful. I also hope in the future there will be an easier and more straightforward way to connect. There probably is now but I just dont know it. Half bread they say is better than none. cheers
If the fix from lombardo8 does not work/apply to you - try the following:
1) Setup/ connect an ordinary BT serial port from your PC to the phone.
2) Use the Widcomm BT applet as monx suggested above to setup the rest.
I have found that I cannot initiate any BT activity from my phone to the PC without a connection made from the PC to the phone first - even though the PC and phone both use Broadcomm stacks!
Also my Tytn II worked perfectly with my PC so likely not to be a PC problem.
Hope this helps...
lombardo8 - you are the dude!
this worked! indeed, i too am running the toshiba BT stack. it's the one i found before worked. I had tried creating all sorts of new connections from the PC settings, but the difference you have found is in the BT options/general settings.
Strangely, the "select PAN networking service" box was not checked. i guess this explains why PAN networking wasnt active. however, what is strange is that this must have worked before using my old TyTn II without this setting.
So once this is enabled, it makes a connection fine!
with regard to wire tethering, this is always a handy fallback, but i have found that BT usually worked quite well, once set up and working, additionally you dont need a wire.
For the life of me i cannot get it to work with my work notebook running Win7 and my netbook running Win7 & OSX
It's driving me nuts
Why can't they just leave it simple. Damn Bluetooth 2.1
Is there any chance somebody can have a .cabs to install back the old internet sharing where there is a Bluetooth PAN in the drop down list. I figured that would be alot easier.
I had the same issues with TP2 and a Mac Book Pro. It works perfectly on Windows XP on this machine but not in OSX. I found a solution for OS X though:
http://forum.xda-developers.com/showpost.php?p=4101986
Thanks for the info but now i'm getting the error msg below
"Failed to establish Internet Sharing connection to remote devices as it supports only Network Access Point (NAP) mode"
What does that mean and how do i configure it in OSX?? Appreciate any help with this as i need ISC in OSX.
Well it means that TP2 thinks that your Macbook offers the internet sharing and not the TP2. I get that same message until i kill the blued and tick that mark again. Then it works until next reboot where i have to repeat the sequence again. Which OSX Version and hardware are you using btw?
Seems the new Snow Leopard fixes some issues with bluetooth. I re-paired my TP2 with Snow Leopard and this works like a charm out of the box. No more fiddling with the bluetooth daemon. Let's see if it stays that way
Just disable DHCP on laptop/PC PAN & u r ready to go.
Scann69 said:
Is there any chance somebody can have a .cabs to install back the old internet sharing where there is a Bluetooth PAN in the drop down list. I figured that would be alot easier.
Click to expand...
Click to collapse
Yes bro. v1.11 will have this feature but still Widcomm stack & bt PAN working 100%
Bluetooth ICS Windows 7 WinMo 6.5
I'd like to chime in here. I've flashed several 6.5 ROMs, but with the 23016 and 23017 sys roms I can't seem to connect bia BT ICS. The USB cable works fine. It seems that my netbook does not acquire an IP address from the TouchPro. I'd sure like to find a fix for this as I use this technology all the time.
@izzyforreal
see my post above. did u disabled dhcp on ur netbook bt pan profile?
monx® said:
@izzyforreal
see my post above. did u disabled dhcp on ur netbook bt pan profile?
Click to expand...
Click to collapse
Hi monx!
How do you disable DHCP on the PC's BT PAN profile? I'm using Widcomm/Broadcom firmware 2.1.211.299 by the way.
And if I do disable it, how will the PC get an IP address??
Thanks,
- Shay
skamin said:
Hi monx!
How do you disable DHCP on the PC's BT PAN profile? I'm using Widcomm/Broadcom firmware 2.1.211.299 by the way.
And if I do disable it, how will the PC get an IP address??
Thanks,
- Shay
Click to expand...
Click to collapse
I've found the solution here. Not using the "Internet Sharing" application though but a couple of nice hacks. IT ACTUALLY WORKS!!!
See attached ZIP with files and that post quoted.
- Shay
Hi, first of all sorry for my english...
This is my problem: I have a BA Windows Mobile 2003 and I want to use it like a modem for my laptop (using gprs connection).
I read the wiki Blue Angel as USB Modem but something is not working.
My laptop OS is Microsoft Vista. I can see the "HTC USB Modem" in the modem list and the port selected automatically during installation was COM4 and I don't know how to change it if necessary. If I launch the "USB MODEM Dialer" in my laptop i can't see a modem available (Modem: <No USB Modem>).
The BA is connected to the laptop using the USB cradle.
Someone can help me?
Is there a way to connect the laptop using wifi with the BA and use the the gprs connection to reach internet? I tried WMWifiRouter but it is not compatible with Windows Mobile 2003.
Andrea
hello and welcome to the forum, there are several options for you:
- you could try -=HTC Wifi Router=-, which is much better than wmwifirouter, but might not work with wm2003, sorry i can't test that, i use wm6.5
- and that would be the next thing, why not try and use another rom, nobody forces you to use such an outdated OS, try wm5, wm6, wm6.1 or wm6.5, you wouldn't have any problems with incompatible software then.
- or, and that might just be the one you'd pick you make up an ad-hoc wlan connection.
the way to do it is:
1. make sure, your pc has all the drivers needed for wireless lan installed
2. ALL of them, forget windows zero config, when it comes to ad-hoc, install all the nifty little tools, you thought, you could live without, because from now on, you can't anymore.
3. then open the tools and make them the default program for managing wireless communication, so that then, when you take the windows wlan search, it does not search for networks, but says, "some other program is managing wlan, windows can't search for networks" or something similar, then you are right and coming closer.
3.a you might have realized, i can't describe all that in detail. i don't know, your wlan device manufacturer, your native language and many other aspects necessary to describe with more detail.
4. on your pc, go to "network connections" right click your wireless device and go to properties.
5. select TCP/IP v4 and click settings
6. set it on manual and choose the following, from top to bottom:
ip 192.168.1.101
snm 255.255.255.0
gw 192.168.1.1
dns 192.168.1.1
adns 192.168.1.2
7. go to your device and call up start->settings->connections->network cards, go to the 2nd panel, select the tiaxclwlan(or something like that) and set the ip config on manual and use these settings:
ip 192.168.1.1
snm 255.255.255.0
gw 192.168.1.1
dns 192.168.1.1
adns 192.168.1.2
8. having all these things set, you can now start your ad-hoc wlan on your pc, using the manufacturer's tools, which should provide you with an option to set up a new ad-hoc
9. select encryption wep and choose a key according to the regulations of wep keys (13 numbers are just fine i believe)
10. take your BA and start looking for wlans in range, make sure "all networks" is selected, and NOT "just accesspoints"
11. as soon as the network is found, connect and enter the key you picked in 9.
12. as soon as you are connected your gprs connection should be shared with the pc. since i am not an expert when it comes to gprs and i don't have my device with me, because i am at work and just can't re-create the conditions, i had to write this all by heart, maybe there are some inaccuracies, but, as always, there are small things to be determined by intelligent guessing or googling
nice work by the way, making your first post this hard to answer, because you looked up things yourself in before.
with best regards,
Chef_Tony
Post deleted,
double post
Thank you (a lot) for the long answer!
1) -=HTC Wifi Router=- is not working on WM 2003, i already tried before.
2) (try wm5, wm6, wm6.1 or wm6.5): i will do it in the future, but I need a fast solution in one/two days. I will try with wm6.5 after holidays
3) I followed what you suggested (not only the nifty little tools, I don't know what they are and where they are). At the end of all I have the laptop and the BA connected wireless, but I can't open gprs connection on the BA. To do it, i usually opened a web page with IE, but if i do it now, IE will try to find the page using wi-fi connection and not trying to open a gprs connection.
The edit button in the forum is not working, so i write another post:
if i go to "Wireless manager" i can connect to gprs and i can see the gprs button green. Then i go to "Wireless LAN management" or something similar (i don't know because I have an italian OS) and i click on "Wireless lan actived" to connect to the laptop. If I go back to Wireless manager i can see the gprs button becoming red and the wlan button becoming green. And i lose the gprs connection.
that is too bad, as mentioned before i am not an expert on gprs, in fact i never used it before, because it is hellishly expensive but i used the other way around often, connect via ad-hoc wlan to a pc, connected to the internet by lan, i even connected to a wlan router once that was not connected to the network, but another client pc, connected to the internet via lan and connected to the router allowed me to go through the router and then through the pc to the net, that was neat, those things are, where i recalled the ad-hoc informations, who would have guessed the BA was as "smart" as preferring the free and faster connection. there must be a way to force it!
i will continue to think about it and hope more senior members have a look into this and maybe advise you on how to do it (although i have to admit, at this point i believe, before a solution is found, more than one or two days might pass by, which makes upgrading a faster alternative again )
Thank you Tony. Tomorrow i will leave home for holiday, and without solution i will be disconnected from internet for 15 days... but when i'll be back i will try to upgrade the operative system.
If someone will be able to give me a hint for my problem... i remeber you that I will go in holiday tomorrow, not exactly now....