HI all,
I'm having some fun and games with my Orbit today.
I previously had an old version of black & Blue on there. SO today decided to update to have a go with some manilla based ROMS.
First I Tried YuE_v11.3_3.15.20755_Lite_M2D_WWE
Which seemed to work ok but after a while applications were being very slow.
So then I tried to reflash oop, but that seemed to fail.
I Tried to flash love, but it wasn't ever getting to the progress indicator on flashing, so did an SD flash of YuE which worked.
So then tried to flash Love from that minimal YUE and the device is being really slow, like gets to the calibration and takes about 5 mins to swap between screens.
What's the best way to totally clear down the rom and start again on this?
Thanks
I've now flashed the Official UK O2 WM6 ROM and still having problems. Flashed succesfully, but when it boots up, it just sits on the "Windows Mobile" screen and beeps a bit
Current State after O2 flash :
IPL : 3.04.0001
SPL : 3.04.0000
GSM : 03.06.90
OS 3.4.0.0
Any help gratefully appreciated.
Thanks
Hard reset the device, and while you're in the config wizard, plug in your device and flash to new rom. That way it's completely formatted and you'll have a fresh new install... hope it works mate
I did a hard reset, still no joy, hangs on the welcome to windows screen
I can access the Bootloader, but can't find a way to flash a rom from there, all seem to want it done once you've made an activesync connetion
flash YUE back via SD card flashing
I already tried that, flashes fine, but becomes unresponsive soon after
have tried flashing O2 WM5 + WM6 from SD, but still no joy.
It just flashes, loads up WM(5/6) then hangs there, beeping sometimes. Pressing the green button brings up the calibration screen. I sometimes see bits of apps, today screen, but that's about it, it's generally unresponsive.
Any suggestions?
ta
A little update incase someone can help?
I left the battery out of the phone all night last night, and this morning the phone worked great.. for about 2 hours, then it froze. I hard reset, and it's back to freezing after OS loading now
What's up if you remove your MicroSD card ?
That makes no diff, i've tried flashing with + without the SD card (it's currently out), flashing from windows + flashing from microSD, all ends up the same way, with an unresponsive device once the OS boots.
Related
Hi there, i got hold of a Hermes yesterday and since that moment i've been trying to flash it to a decent wm6.1 rom.
but i ran in some problems.. first i flashed HardSPL 7. then i flashed the radio to 1.4x and even 1.5x and some roms. the last ROM i tried is the latest TNT.
but for some reason i keep getting crashes, missing shortcut links and when i reboot at that moment it keeps stuck at the bootscreen picture. this happened serveral times now and its getting on my nerves..
i already used MTTY with the info 8 command. and it only returned some "Reversed" blocks, none were bad.
Can someone please tell me if i am doing something wrong? or how i can solve the issue?
i already tried leaving it be for 5 minutes, remove battery, and did like 30 hard-resets already..!
help?
happened to me once
have you done a manual hard reset? at least i think thats what its called. where you hold both soft keys(ones above start/ok) and press the button in with your stylus all at one time till the white reset screen comes up..then just press R and SPACE on the keyboard.
now once it reloads and is finally done...flash vg3's at&t wm6 rom..once its all done flash your 6.1 rom of your liking..
its something to do with the memory i dunno but i just flash vg3's at&t wm6 rom every single time before i flash to another 6.1 rom and i've never had that happen to me again and trust me it happened a lot before..it never happens now
Yes i did do the hard-reset manually.
i will try the vg3's rom first thing tommorow.
Alright, forum friends. On Friday I flashed Anryl Beta 3 using sspl on my sd card. During the day on Friday and Saturday, my phone would occasionally freeze up forcing a soft reset. When I reset the phone, it forced me back through the initial setup (tap screen to configure, setup time zone and email, etc.), essentially forcing a hard reset. Now my phone is stuck at the 1st splash screen and won't finish booting up. The green LED on the right side is lit (the GSM light) and it just hangs there. A soft reset sends it back to the same spot. A hard reset has done the same.
I tried to flash a new rom using the bootloader but the HERMIMG.nbh won't take - it says "Loading..." across the top of the screen then flashes 00068002, then goes back to the red, green, blue and white bootloader screen. Does anyone have any ideas for rescuing my poor phone? I'm up for anything now!
Flash your carrier original ROM, or VP3G or AT&T ROM and see if that helps!
I've tried to flash my original ROM (both the first one that came on the phone and the WM6 release from ATT) but I can't run them from my PC since I can't get an activesync connection. I tried to download the nbhextract file from the forums here and it says that the file is corrupt. I've tried flashing other roms to my device (using my SD card and the .nbh image) and keep getting the same result.
If it helps, here's my info from bootloader: HERM100, IPL-1.04, SPL-2.03.
By the way, I just moved back to my old Ericsson P800 and am dying to get back to my HTC!
So I downloaded the update from HTC's website (the original 6.0 ROM from AT&T) and am pushing that over now. I had to turn off the USB on activesync to get it to connect but everything seems to be going just fine now. Thank you all for all of your help. Hopefully this will be the last post on this thread.
Hello, i have a new P3300. The first time i opened it it started installing some basic stuff/programs and then worked quite good. Then i turned it off and when i turned it on again it shows the first splash screen with the htc logo, shows IPL and SPL versions on the left top side (like it should do) and then it instantly turns off. I have tried installing the official WM6 ROM again and again but after the installation finishes the problem remains. Also, when in confirmation dialog for the ROM to be installed or not when it shows the old and the new version, the old is completely blanc.
P.S.: Something else, when i connect it to charger (or USB cable) the orange light keeps going on and off about every 30 seconds.
Any help would be highly appreciated guys.
Send it back to your vendor for warranty...
Cheers
After many tries i managed to install some older official ROM but again after the initial screen calibration and the other stuff some customizations started installing and when PDA rebooted the problem appeared again. But tomorrow I'm getting it to service (and getting my Qtek 8310 back which by the way got a repair although unlocked ).
Hi there xda's !
I have a problem with my Touch Pro2
It has bin running fine, with lots of different roms, until this morning, when it on startup hang at the first welcome screen (the one with white background and the HTC logo)
Usualy there are some red letters in the left bottom corner of the screen but not this time.
Also, the small lamp that indicates if it is recharging and stuff, does not work anymore.
However, if i wait for 30 minutes, it will eventually boot up, but the phone is so slow, that it takes another 15 minutes to startup, and everything works slow when i am in the OS. And then it turns it selv off.
I have tried to do a task29 and install a new rom, and it installs it flawless and fast like it normally would, but it still doesnt boot up. Only after 30 minutes.
When i am in the bootloader it also has these 2 lines
MicroP(LED) Wrong Plat(0x0)
MicroP(KEY) Wrong Plat(0x0)
Is my phone bricked? Or is there something i can try?
nubx said:
Hi there xda's !
I have a problem with my Touch Pro2
It has bin running fine, with lots of different roms, until this morning, when it on startup hang at the first welcome screen (the one with white background and the HTC logo)
Usualy there are some red letters in the left bottom corner of the screen but not this time.
Also, the small lamp that indicates if it is recharging and stuff, does not work anymore.
However, if i wait for 30 minutes, it will eventually boot up, but the phone is so slow, that it takes another 15 minutes to startup, and everything works slow when i am in the OS. And then it turns it selv off.
I have tried to do a task29 and install a new rom, and it installs it flawless and fast like it normally would, but it still doesnt boot up. Only after 30 minutes.
When i am in the bootloader it also has these 2 lines
MicroP(LED) Wrong Plat(0x0)
MicroP(KEY) Wrong Plat(0x0)
Is my phone bricked? Or is there something i can try?
Click to expand...
Click to collapse
Try reflashing the stock SPL and then Hard SPL again.
cajunflavoredbob said:
Try reflashing the stock SPL and then Hard SPL again.
Click to expand...
Click to collapse
Thank you for the suggestion
In attempt to do so, i got the phone booted up again, and it actually worked normally untill you turn of the screen (pocket mode, or what ever), but then it wont come back on again, i can reseave messages, and call the phone.
Anyhow i cannot get activesync or "windows mobile device manager?" installed on my x64 windows 7, so i am waiting for an oppertunity on another computer, but untill then i am open for suggestions
Get 64-bit version of windows mobile device manager. You can also try a radio upgrade.
DGeneral02 said:
Get 64-bit version of windows mobile device manager. You can also try a radio upgrade.
Click to expand...
Click to collapse
well, my phone will nok make an active sync connection once in windows mobile, guess it because everything is so slow.
Is there anything i can try to install from the bootloader, since that is the only place i can install stuff on my phone?
nubx said:
well, my phone will nok make an active sync connection once in windows mobile, guess it because everything is so slow.
Is there anything i can try to install from the bootloader, since that is the only place i can install stuff on my phone?
Click to expand...
Click to collapse
You can install from the SD card by renaiming the *.nbh file to RHODIMG.nbh and putting it in the root of the SD card. Boot into the bootloader and it will ask you to confirm the flash with the power button. This method can be done with ROMs, radios, and splash screens.
I installed a rom/hardspl and new radio yesterday, didn't like the rom so much for slowing sometimes, wanted to switch to another rom, saw the Eto.Y 2.4 sense 2.5 and tried to install (Didn't read that I have to change radio aswell), was installing well, though I didn't understand about the task29 thingy, still kept pressing next, till the download bar, I went to DC, came and found my phone soft reset, and finished the instalation, but the problem is, my phone freezes on the startup picture that says "TOUCH diamond"
Please help me solving this problem ASP!
Nvm, solved it, close this.