Hi everybody;
I'm trying to update my HTC DIAMOND.Everything seems ok.Activesync detects my phone.
Image version 1.35.456.3 to i.93.479.3KRM
Then phone goes to BOOT mode;
SPL : 1.35.0000
Then i can see progress bar on phone LCD but it takes few moments and i get "UPDATE ERROR" and it takes me to RECOVERY page.
As mentioned in "READ ME" file:
This error occurs during the CE ROM code upgrade process.
I soft reset and restart RUU but the same thing happens.I changed USB cable and tried on another PC but the same
PLZ help.
I'm using activesync version 4.5
Install Hard SLP!
i had the same problem..
the solution for me was to upgrade the hard spl
so try to use the last version
CU
thanks,i'll try and post result.
Related
I upgraded my 85' with the "official" wm6 rom and now I cannot go to other roms. The process was solid, meaning I was fully charged, no power loss, and it was synced. I've tried every version of rom available and get the same results. I went through the "brick" thread and I'm affraid I don't quite fit into any category. I can get phone calls and everything works, I just happen to like all of the great ROM's everybody is cooking and want to try them to see which one I favor. I tried using the Hard-SPL and all of the other bootloaders out there and I always get that ERROR [206]. I've tried to restart the machine, and hard reset the 85'. Any good idea's.... Maybe I need to search more? I'll try that.
==============================================================================
UPDATE:
What I should really do is rent a gun, and buy a bullet...
I'm not saying I'm some sort of season veteran of flashing... but I've never had to touch anything after I accept all terms. For some reason, when it came down to the last "Next" form, my phone flashes "Accept" super fast. So what to do?... I push "Yes" soft key fast as I can and it runs like grease lightening... I had to choose SS for the boot loader because it couldn't figure it out... Maybe next time around.
Have you tried to flash a coocked ROM using the microSD card?
Hi,
did you try get your phone in the tri color bootloader screen and then running the Hard SPL program again?
I did not try to do flash it woth the MicroSD card... I just found out that I could flash it with the MicroSD card about 2 seconds ago. And I wanted to Hard-SPL at the tri-color as a last result in fear of bricking but everything is okay now. As I said before, I've never had to touch my 85' while flashing the rom, it just did it on it's own, but that "official" rom was not about being neglected. And then when I saw it flash something and say "yes", I pushed it and never looked back. It's alllllllllllllllllll good.
I do have one question, is the SSPL preferred over the other choices? Or is there one that is recommended?
Hi joshkrajnak,
How did you solve this problem exactly cos I dont understand what your saying:
http://forum.xda-developers.com/showthread.php?t=298640
boz said:
I extracted these error codes from a Hermes rom upgrade 'read me' document, these should be of help if you get an error message during a rom upgrade. They should be common to all roms, please correct me if I am wrong.
ERROR [202, 204] : CONNECTION
This error message will appear when the device is not connected to ActiveSync correctly. Make sure you properly connect the device to the PC through ActiveSync before running RUU.
ERROR [260] : CONNECTION
This error occurs when there is an “open port error” before upgrading the CE ROM image.
Solution: You can reset the device and run RUU again. If you still encounter an “OPEN PORT ERROR” again, reset your computer and try again.
ERROR [206] : MEMORY ALLOCATION
ERROR [280] : UPDATE ERROR
When you see any of these error messages, close other running programs on the computer and run RUU again.
ERROR [208] : FILE OPEN
ERROR [210] : FILE READ
These error messages indicate that RUU lacks certain important files and cannot continue with the update. Please get the complete RUU package again.
ERROR [212] : FILE CREATE
ERROR [214] : FILE WRITE
ERROR [222, 224] : DEVICE NOT RESPONDING
These error messages will appear when remote access control has failed. Check the ActiveSync connection and try running RUU again.
ERROR [220] : MAIN BATTERY POWER
This error message will appear when the device’s battery power is not sufficient. Although RUU will instruct you to plug in the AC adapter, it still has to make sure that your device has enough power to upgrade the radio. (Even when you plug in the AC adapter, the device is unable to charge the battery when it is upgrading the radio).
ERROR [238] : FILE READ
This error message may appear when, for some unknown reason, the ROM image on the Mobile Device is corrupt. Download the whole RUU and try again.
ERROR [240] : FILE OPEN
When this error message appears, check whether the downloaded image is placed in the directory of RUU. If, for some unknown reason, you find that the ROM image is not located in the RUU folder, you have to download the RUU and retry again.
ERROR [242] : INVALID LANGUAGE
ERROR [244] : INVALID MODEL ID
ERROR [294] : INVALID VENDER ID
ERROR [296] : UPGRADE ONLY
One of these error messages will appear when you use the wrong RUU to do the upgrade. RUU will check if the Model ID and Language ID are compatible with the device. Make sure you use the appropriate RUU tool to upgrade.
ERROR [246] : DEVICE NOT RESPONDING
This error message indicates that RUU cannot start the update process. Please contact your service provider for assistance.
ERROR [262, 276, 284, 302] : UPDATE ERROR
This error occurs during the CE ROM code upgrade process.
Solution: If this happens, you can just soft-reset the device and run RUU again. The update process will then continue.
Note: At this stage, the Wince is destroyed; instead, it is in upgrade mode.
ERROR [300] : INVALID UPDATE TOOL
This error message will appear when you use the incorrect RUU version to upgrade.
ERROR [330] : ROM IMAGE ERROR
This error message will appear when you use the incorrect RUU to upgrade and the image file size is larger than the Flash ROM size. In this case, download the correct RUU version to upgrade.
Click to expand...
Click to collapse
To Clarify: Whenever I went to upgrade my 85' to a different ROM, it wouldn't recognize my bootloader, and then after selecting any of the options, it would give the "ERROR [206]" message and fail miserably with any rom.
What I did to correct it was this: On the "official release" whenever I went to upgrade the ROM, the 85' would show a message at the bottom, the same as any "Notification" would giving me the option to either "confirm" or "dismiss". I did not notice the messages up until it caught my attention out of the corner of my eye on the very last attempt. The messages would quickly appear and disappear, so when the time came and it stated:
Current Rom: 3.25.###.###
Upgrade: 1.##.###
I had to press a confirm notification to continue on or I would get the "206" error message. The quote posted by Binyo is correct, but it does not apply in my situation.
ERROR [206] : MEMORY ALLOCATION
ERROR [280] : UPDATE ERROR
When you see any of these error messages, close other running programs on the computer and run RUU again.
Although that may be true that some applications may interfere with the upgrade process, I had turned off all applications and killed any services during this process.
I have successfully installed Hard SPL into my HTC TyTN (Qtek 1.18.255 ROM) but I cannot get the ROM upgrade utility to work. I have tried using both the latest Qtek 2.11.255 ROM as modified for Hard SPL and using the upgrade utility as shipped (which I know would replace Hard SPL).
In either case the process stops at the point where I get the progress bar, I get through the verifying the information on your phone screens and confirming the ROM image but it never gets past the "Updating the ROM image on your PDA Phone" box.
The progress bar remains at 0% and eventually I get the message:
ERROR [260] : CONNECTION
The Update Utility cannot connect to your PDA Phone. Please check that your USB cradle/ cable is connected...
Needless to say the cable is connected but I notice that Activesync has disappeared at this point. There is nothing to do but exit the upgrgade. When I do, Activesnc reappears
Has anyone else come across this issue?
Help would be much appreciated
Simon
I had a small problem:
I want to upgrade ROM from 1.35.401.3 to 1.93.401.2...
I download the official .exe from HTC:
Diamond-QMR-RUU_Diamond_HTC_Europe_1.93.401.2_Radio_Signed_Dia mond_52.29.25.12_1.00.25.05_Ship
using the S/N from the back of my PDA
... it work till 34%, then it appears UPDATE ERROR:284
"ERROR [262, 276, 284, 302] : UPDATE ERROR
This error occurs during the CE ROM code upgrade process.
Solution: If this happens, you can just soft-reset the device and run RUU again. The update process will then continue.
Note: At this stage, the Wince is destroyed; instead, it is in upgrade mode."
What do you recommend to do?
I repeated the process 5 or 6 time, the same stop, at 34% and even recovery is useless
Please help...
there are a couple of things you can try...
1st off, put the phone in bootloader mode (hold "volume down" button and press reset with pen) then flash using a windows XP machine with no running services such as Anti Virus/firewall etc.
if not, try hard SPL developers edition, and then flashing it...
Amz
amzchhabra said:
if not, try hard SPL developers edition, and then flashing it...
Click to expand...
Click to collapse
That would be impossible in bootloader mode using the current toolchain.
The Hard SPL uses a soft SPL that has to be loaded into RAM from within Win CE.
This Soft SPL forces the device to think that it's CID unlocked, and letting the actual Hard SPL flash to the device.
Maybe a hard reset would help:
http://www.hardreset.eu/htc_touch_diamond_hard_reset_soft_reset_en.html
Good luck to you friend.
May be the file u have is corruped, try another ROM!!
Which OS did you use to upgrade from?
Have you tried to use a PC with XP (proffesional) with activesync 4.5 installed?
if all fails:
-kill wcecomm.exe on the PC (with taskmanager) (or disable activesync)
-put Diamond into bootloader..
-Run the official RUU again.
(worked for me on other devices too.. )
All is not lost..
gabib77 said:
I had a small problem:
I want to upgrade ROM from to 1.93.401.2...
I download the official .exe from HTC:
Diamond-QMR-RUU_Diamond_HTC_Europe_1.93.401.2_Radio_Signed_Dia mond_52.29.25.12_1.00.25.05_Ship
using the S/N from the back of my PDA
... it work till 34%, then it appears UPDATE ERROR:284
"ERROR [262, 276, 284, 302] : UPDATE ERROR
This error occurs during the CE ROM code upgrade process.
Solution: If this happens, you can just soft-reset the device and run RUU again. The update process will then continue.
Note: At this stage, the Wince is destroyed; instead, it is in upgrade mode."
What do you recommend to do?
I repeated the process 5 or 6 time, the same stop, at 34% and even recovery is useless
Please help...
Click to expand...
Click to collapse
Hi gabib77.
As long as you can get the coloured bootloader screen all is not lost, you can still flash your Diamond in the bootloader mode, i.e run the rom update from your PC as normal.
I would first suggest you reflash back to the original rom, try here http://forum.xda-developers.com/showthread.php?t=399680, I am not sure what the "QMR" info you stated on the upgrade rom means, but the second link from the HTC Diamond ROM's List is for the WWE version (1.35.401.3 WWE)
If you cannot flash your Diamond in bootloader mode, then try a hard reset first as mentioned on this thread first.
If you all goes ok then go to http://modmydiamond.info/ for more info on flashing.
Good luck.
I solved the problem... my problem happened because I try to upgrade from 1.35.401.3 to 1.93.401.2...
I put the official 1.37.401.2, then I upgraded to 1.93.401.2 WWE and everything is perfect now...
Thanks everyone for the help
Hello,
if got the T-Mobile MDA III with WM6.0.
Now i want to update my ROM with WM 6.5, bit i only become the following error:
Your image has corrupted. please check your update utility.
Can anyone help me???
i hope you can help me.
thx
markus
try to re-download the rom and make sure you run a USPL first if it's your first upgrade. Search the forum if you need help
it dosn´t works
i´ve tried 5 different roms but no one works.
its the second upgrade on the fon.
Try a new update of SPL, files here= http://forum.xda-developers.com/showthread.php?t=311403
Download "ArtemisUSPL.zip"
1. Unzip
2. Connect your phone to computer, make sure activesync is enabled (green icon)
3. Run start_uspl.exe on your computer and wait until process finishes
4. The phone reboot.
When boot is done, you are CID unlock forever normally so you can flash all rom you want.
Then, You can flash now your rom, just run RUU from your rom folder and normally it's good.
If it always don't work, give us all the number show in your 1st screen when the phone boot (IPL, SPL ...)
yes, tell us what numbers you get on your screen
also what error are you getting
and what OS are you on....vista? XP ? Did you get an activesync connection before you tried flashing?
also try putting phone into bootloader mode first and then flashing, sometimes helps. (hold down RECORD/NOTES button when you reset)
once you've got an error number ( eg error 260 ) you can try searching the forum for that error number and see how everyone else has coped with it.
Dear Sirs;
I've done Hard Spl unsigned olinex 1.93 before and flashed various Cooked ROM befor (the last one was Diaduit 1.6.7). I decided to back to the original ROM, so connected the Diamond to computer and run the original ROM software (RUU_Diamond_HTC_WWE-ME_2.03.456.2_Radio_Signed_Diamond_52.51.25.26_1.09.25.23_Ship.exe). everything was ok and the bar went to 100% BUT then Diamond hanged in Bootloader and "connection error" appeared in RUU screen. I flashed the diamond from internal memory by Diaduit "diamimg.nbh" file which I've placed there before but connection type has been changed from "USB" to "Serial" in Bootloader and I can't flash the mobile by PC anymore.
I will be rally apprecialed if you help to to change the "Serial" to "USB" in Bootloader.
Best Regards
Try following the steps in This Thread to ensure you have the right drivers for the connection on your computer.
If you have bad blocks in the onboard memory this should sort it out and then you can re-flash from internal storage.
MarkG
Let me correct the description. After complete the flash (by original ROM) in boot loader this message appears "Upgrade ROM code error. Please Try again" and in RUU screen (in PC) correction error appears.
I'm going to try MTTY.
Solved! It seems the problem related to the ROM (which I've downloaded from HTC site directly and installed successfully before!!?!) I tried another original ROM (RUU_Diamond_HTC_ARA_2.03.415.2_Radio_Signed_Diamond_52.51.25.26_1.09.25.23_Ship.exe) and diamond flashed successfully!