Hey
I hope some one could help me on this small problem.
I just tryng to resest my XDA IIs back to defaults, clear all on the memory.
Im running WM6 and im a bit lost on how to do a hard reset please help me.
Thank You
Dal.
Hard Reset
If this is new ROM you should go to Boot Loader first.
How to make Hard Reset:
1.Perform Soft Reset
2.Push Record and Camera button at the same time and hold them until the Boot Loader screen shows up.
P.S. You should do step 2. before the Radio version/ROM version appear in the right bottom of the screen.
3.“Enable KITL” must be NO, “Clean Registry Hive” must be YES, “Format Storage” must be YES
P.S. Use the Record and Camera buttons for navigation.
4.Press Mail button.(Do not touch anything until the white screen disappears)
NOTE: IF YOU WANT TO GET RID OT THE PASSWORD(WITHOUT DELETING YOUR FILES) YOU SHOULD PERFORM NO/YES/NO PROCEDURE!
That's it! Good Luck!
hello i have wm6 on my ba and i wanna give hard reset!!! i don't know how! please help!!!!
Have a look here:
- http://wiki.xda-developers.com/index.php?pagename=HTC_Blueangel
- http://wiki.xda-developers.com/index.php?pagename=BlueAngel_For_Beginners
And next time try this one: http://forum.xda-developers.com/search.php
Greets Rossi
pls help~~~
where? i have ba whit wm6!!! i try all of them for there, not working! there is for ba whit wm5 or wm2003! for wm6 nothing!
helppp!!
on/off + reset button at the same time... not work!
recor+ on\off+reset =serial message on the screen ( i think that is bootloader)
anything alse i need! please helppp!!!
I can't hard reset either
I have followed all of the directions on the wiki, I have even tried to install another rom and it still will not remove all of the data, it changed the information in the about section of my settings but that's it. I want to change ROMs but it is not working. any ideas?
What version of windows is on your PC?
also try the enter BL which is on most ROMs
Hard Reset
To hard reset you do a soft reset (power + reset)
and before it shows the version numbers at the bottom you have to press Record + Camera & also power (i think) and then you come to an options screen using the record button to go down the list and camera to select you select Yes for option 2 and 3 and then hit the mail button to apply.
jidi22 said:
hello i have wm6 on my ba and i wanna give hard reset!!! i don't know how! please help!!!!
Click to expand...
Click to collapse
swick off button & rest buton in the same time but take care if is not the original windows you may have problems
Warm Boot: Reset the unit by pressing reset button.
Cold Boot: Press Power ++ Reset the unit simultaneously.
Read this. It's how to hard reset your BA. Hope it helps. Make sure you already formated the storage.
Code:
http://wiki.xda-developers.com/index...izzardUpgrade4
Hi all...
My Blue Angel wont hard reset. I just bought it second hand and have been trying to hard reset it. I read up and the instructions are to keep the power button pressed while resetting with the stylus. But no matter how many times I tried, this procedure only soft resets the device. Please help!
Try it the software way by going to start>settings>system>clear storage>1234>ok.
kareem9nba said:
Try it the software way by going to start>settings>system>clear storage>1234>ok.
Click to expand...
Click to collapse
Hi buddy.. thanks so much for the reply... but its not working.. tapping on the clear storage icon in settings does not bring up the password screen or do anything at all
wat are my other options people... pls help
anybody??????
i think you make wrong HardReset.
for Hard Reset a BA just press RECORD+CAMERA/PLAYER+SOFT RESET 2 sec. and walaahhh.... there you go.., You'll see three options on screen. You must change the second and the third to yes. If you are not developing/testing software you can disable the first debug option for better performance.
have a nice reset
Stevo.Mksr said:
i think you make wrong HardReset.
for Hard Reset a BA just press RECORD+CAMERA/PLAYER+SOFT RESET 2 sec. and walaahhh.... there you go.., You'll see three options on screen. You must change the second and the third to yes. If you are not developing/testing software you can disable the first debug option for better performance.
have a nice reset
Click to expand...
Click to collapse
Thank you soooo much Stevo... Ur method worked... I wonder why the wiki itself has the wrong method for hard reset... Maybe the hard reset varies from brand to brand... although it should not be since the hardware essentially is the same... Anyways... Hopefully one of the moderators would read this thread and add your method to the wiki...
Million thanks again...
I get that 3 choice screen, but how to I get it to hard-reset AFTER that? If I hit the soft-reset I get the same thing I have gotten for the whole day before. :-(
on the screen must be shown
enable kitl :choose no
clear registry hive : choose yes
format storage : choose yes
change it using the record and camera button.. after that use the mail button to proceed the hard reset
evoluzionne said:
on the screen must be shown
enable kitl :choose no
clear registry hive : choose yes
format storage : choose yes
change it using the record and camera button.. after that use the mail button to proceed the hard reset
Click to expand...
Click to collapse
tried the above but unable to press enter using mail button to initiate rebootin. pls help
Procedure works as advertised
I also was scratching my head over the Hard Reset info in the Wiki not working. This procedure did the trick. Thanks for the help!
Also, for the poster who had trouble with the Mail button not initiating a reboot, just hold it until you get an all white screen, that's what I did and it worked like a charm!
Hard Reset Big Thank Q
Hi every1, the step does work & i would like to thks those who has shared there thought with all.
juz press the "mail" button for about 3 miniutes & you shud see a totally white blankscreen & then it will bring you to formatted WM6. whatever u install previously will be wipe out.
After i hv tried various method.Honestly, this is the only method work to overcome "EXTREME FROZED WM6".
Thks to XDA developer community for sharing.
Just curious, any1 know wat mig hv cause the "EXTREME FROZED WM6"?
Have a nice day every1.
RGds
Thks mysteroid,
For making me holdin on to d "Mail" button. It really works. Brilliant.
Have a nice day.
Consolidated Solution
To the next member whois searchin for a solution here it is:
Problem:My O2 XDAiis won't hard reset. WM6 deep FROZED.
Solution: Extreme Hard Reset a XDAiis just press RECORD+CAMERA+SOFT RESET 2 sec. and walaahhh.... there you go.., You'll see three options on screen. Then use RECORD+CAMERA/PLAYER button to change the value on the setting.
Setting: on the screen must shown
enable kitl :choose no
clear registry hive : choose yes
format storage : choose yes
Finally: use the mail button(act as enter) to proceed the hard reset. U might need to press & hold it for 3minutes.
Kudos to original contributor :Stevo.Mksr(for method) , evoluzionne(for setting) & mysteroid(for keepin the faith).
WM6 deep FROZED -> check/replace your battery
Hello,
a few days ago I recognised the implemented feature "Soft Reset Device". (In Joshkoss Rom etc...)
Does this Application can cause data loss?
Is it better to make a normal shutdown and then power on again in order to restart the device?
Please Help!
sapphire_pro said:
Hello,
a few days ago I recognised the implemented feature "Soft Reset Device". (In Joshkoss Rom etc...)
Does this Application can cause data loss?
Is it better to make a normal shutdown and then power on again in order to restart the device?
Please Help!
Click to expand...
Click to collapse
Only if the you havn't saved data program(s) you are using. It's the same as rebooting windows on your PC.
Ta
Dave
HI,
so if no data or program is opened I can just tick the button and the system gets no internal failure message or something like this, right?
I just want to be sure that I do not not crash the system while using soft reset.
sapphire_pro said:
HI,
so if no data or program is opened I can just tick the button and the system gets no internal failure message or something like this, right?
I just want to be sure that I do not not crash the system while using soft reset.
Click to expand...
Click to collapse
Without looking the Soft Reset should just call the Windows API to Reset the Phone, so nothing will be lost / broken, etc.
Ta
Dave
Ok, thank you for your help!
sapphire_pro said:
Hello,
a few days ago I recognised the implemented feature "Soft Reset Device". (In Joshkoss Rom etc...)
Does this Application can cause data loss?
Is it better to make a normal shutdown and then power on again in order to restart the device?
Please Help!
Click to expand...
Click to collapse
soft reset is a normal reboot per say.. no data is lost.
Hi all,
Just received my Vodafone-branded Diamond, and I'm afraid I already managed to brick it!
It was equipped with version "1.37.172.3 NLD" so I decided to upgrade it to the latest version.
The installation of OliNex Hard-SPL 1.93 went flawless, but the installation of ROM "RUU_Diamond_HTC_WWE-ME_1.93.456.2_Radio_Signed_Diamond_52.29.25.12_1.00.25.05_Ship.exe" stopped at about 25% with error code 302. The recovery method that came with the package didn't help, every time the upgrade stopped at the same moment.
Since the device is stuck in the bootloader, and I'm left with a non-chargeable battery, I tried the official Vodafone-branded "RUU_Diamond_Vodafone_NL_1.97.172.4_Radio_Signed_Diamond_52.44.25.24_1.08.25.08_Ship.exe" ROM. Unfortunately, this upgrade stops at 48% and throws the same 302 error.
Anyone who can tell me what I'm doing wrong, and what I can do to solve all this?
I hope I don't have a brand new, but bricked device on Christmas!
TIA and have a nice day.
Try a hard reset first. If this doesn't help google or search at XDA for MTTY.
This tool can fix your device
http://wiki.xda-developers.com/index.php?pagename=Kaiser_Stuck_at_bootloader
Try this, maybe will work
Try a Vodafone branded stock rom before mtty.
Regards,
Carty..
He already tried a stock rom....
Potential Solution
Have you looked at the thread titled,
[UPG][TRBL]How-to fix: Update/Flash doesnt work, stops at 0% or 5% (invalid model ID)
It may just be a model ID glitch that can me fixed.
Take a look. It's in this forum in a sticky by cptsunshine.
Thanks all for the help, I'll have a look at your suggestions.
The problem isn't that it stops at 0% or 5%, it stops at random percentages (depending on the ROM I use).
I also see the bootloader (red / green / blue), so it's not dead. I guess it's just that it doesn't pick up a ROM.
Besides, the bootloaders says upgrade ROM code error please try again.
Edit:
A hard reset doesn't seem to work. In the bootloader, when I press "volume down" and "enter" together, and press the "reset button" the screen goes black, but then goes back to the bootloader screen after a sec or 2.
Edit 2:
MTTY doesn't do much either, after executing "boot" the phone is showing me the Vodafone logo and that's it.
For the rest, MTTY shows me the following:
Cmd>boot
InitDisplay: Display_Chip=1
dwDirectNum: 0, dwMatrixNum: 0, dwMicroPNum: 0
Fixed new dwPSImageSize = 0x53E0000
Install Rom via Internal Memory Method
Steps from Suiller:
1. open from your PC the rar or zip archive and extract only the BIG .nbh file
2. rename as DIAMIMG.NBH
3. copy the renamed file into the root dir of your "Storage Card" or "Internal Storage" (the one of 4Gb... NOT to the internal phone memory!)
4. reset your device and within 3 seconds push together the Vol_Down + Back button (the one on the right above the hangup button) and keep pressed until the boot loader appears (the one with the color stripes)
5. soon as you see the bootloader stop to press those poor buttons
6. a very simple gray menu will appear asking you what to do, simple press the power button to perform the ROM/Radio upgrade
7. while the upgrade runs be patient and don't press again the power button, reset the device or play with it until it finishes, when finished a message "UPDATE SUCCESS" will appear, now you can safely reset your device
8. who prefer can perform a hard reset after the fresh cook (soon after reset simply press Vol_Down + Circle button, then when you see another simple gray menu choose Vol_Up to confirm format), even if this has no-sense because internal memory is pre-formatted during flash, but... there is always a but... for some unknown "scientific" reason sometimes an hard-reset can save time & headache
Let me know how it goes.
Make sure you have Net framework 3.5 installed on devices.
Nakkie27 said:
Thanks all for the help, I'll have a look at your suggestions.
The problem isn't that it stops at 0% or 5%, it stops at random percentages (depending on the ROM I use).
I also see the bootloader (red / green / blue), so it's not dead. I guess it's just that it doesn't pick up a ROM.
Edit:
A hard reset doesn't seem to work. In the bootloader, when I press "volume down" and "enter" together, and press the "reset button" the screen goes black, but then goes back to the bootloader screen after a sec or 2.
Edit 2:
MTTY doesn't do much either, after executing "boot" the phone is showing me the Vodafone logo and that's it.
For the rest, MTTY shows me the following:
Cmd>boot
InitDisplay: Display_Chip=1
dwDirectNum: 0, dwMatrixNum: 0, dwMicroPNum: 0
Fixed new dwPSImageSize = 0x53E0000
Click to expand...
Click to collapse
u can do one thing then press woluem down and reset bottom at the same time then u go to rescue mode then u wait and put in the usb stick and there stand seriel when u put in the cable it will change to usb thenu can load the firmware again
band27 said:
Steps from Suiller:
3. copy the renamed file into the root dir of your "Storage Card" or "Internal Storage" (the one of 4Gb... NOT to the internal phone memory!
Click to expand...
Click to collapse
I wish I could mate, but I cannot put files on it anymore, since ActiveSync doesn't recognize my device when it's in the bootloader.
janielsen said:
u can do one thing then press woluem down and reset bottom at the same time then u go to rescue mode then u wait and put in the usb stick and there stand seriel when u put in the cable it will change to usb thenu can load the firmware again
Click to expand...
Click to collapse
Can you please be more specific? Are you telling me how to do a hard reset? I tried as to do a hard reset, but it goes back to the bootloader instead of resetting. USB stick?
Thanks all, much appreciated. A pain this can happen, looking at the fact that I did everything exactly as described in all these flashing manuals.
Nakkie27 said:
I wish I could mate, but I cannot put files on it anymore, since ActiveSync doesn't recognize my device when it's in the bootloader.
Can you please be more specific? Are you telling me how to do a hard reset? I tried as to do a hard reset, but it goes back to the bootloader instead of resetting. USB stick?
Thanks all, much appreciated. A pain this can happen, looking at the fact that I did everything exactly as described in all these flashing manuals.
Click to expand...
Click to collapse
first push the volum down buttom at the same time press the reset buttom then the 3 color display will appear and in the buttom will stand seriel then u putt in the usb cable to ur phone whit u have attact to ur pc then it will say usb now u can load new firmware
janielsen said:
first push the volum down buttom at the same time press the reset buttom then the 3 color display will appear and in the buttom will stand seriel then u putt in the usb cable to ur phone whit u have attact to ur pc then it will say usb now u can load new firmware
Click to expand...
Click to collapse
No mate, I never had problems getting into the 3 color screen. The problem was updating afterwards, which never completed without error code 302.
Anyway, I guess I just fully bricked my device after putting SPL-1.40.OliNex (according to the guide at http://forum.xda-developers.com/showthread.php?t=416211) on it. The SPL install was succesful, but when booting I'm now not even getting to see the 3 color bootloader. All I see is the Vodafone logo with some version numbers at the bottom, but that's it. It doesn't boot further on, and I can't get a USB-connection.
Edit:
Volume down + reset brought me in the bootloader again, although it's saying SPL-1.93.OliNex.
Nakkie27 said:
No mate, I never had problems getting into the 3 color screen. The problem was updating afterwards, which never completed without error code 302.
Anyway, I guess I just fully bricked my device after putting SPL-1.40.OliNex (according to the guide at http://forum.xda-developers.com/showthread.php?t=416211) on it. The SPL install was succesful, but when booting I'm now not even getting to see the 3 color bootloader. All I see is the Vodafone logo with some version numbers at the bottom, but that's it. It doesn't boot further on.
Click to expand...
Click to collapse
that i know but as i say in the post that when u do it that way i say u can load new firmware whitout it needs to boot try my friend i have done it 3 times because wrong loading of firmware
u have to only push thoose 2 buttom then it will work because u go to rescue mode
But what will that give me extra? I can access the Hard-SPL 1.93 bootloader (3 color screen), and I can get into USB mode. It's just that the upgrade of both firmwares stop at a certain percentage.
I'm constantly trying to hard reset the device, but after pushing the reset button (with both volumn down + enter pressed down), the device just reboots back into the bootloader and doesn't give me the hard reset warning.
Nakkie27 said:
But what will that give me extra? I can access the Hard-SPL 1.93 bootloader (3 color screen), and I can get into USB mode. It's just that the upgrade of both firmwares stop at a certain percentage.
I'm constantly trying to hard reset the device, but after pushing the reset button (with both volumn down + enter pressed down), the device just reboots back into the bootloader and doesn't give me the hard reset warning.
Click to expand...
Click to collapse
u need to hold them down until it leave the 3 color display an turns into grey
Ok, finally managed to do a hard reset. Afterwards I tried upgrading to the official Vodafone NL 1.97 ROM once more, but it failed at 48% again.
Any ideas what to do? I know have Diamond with Hard-SPL 1.93 (which says upgrade ROM code error) with no working OS.
Ok all, got it finally working again!
Don't ask me why, but flashing the newest Dutty ROM (and the included radio) did work.
Thanks for all your help, and a wonderful evening!
Hi all,
I have a quit similar problem. I've read a lot, but couldn't find an answer to my problem - may bye someone can help me.
I updated my Dimond (OliNex Hard-SPL 1.93, radio 1.09.25.23 and rom dutty V4). When I start my phone most of the time (95% plus) I end up in the color screen - however some time it's starts perfect (without changing anything).
When I get stock in the color screen, I can start the phone with mtty and the command "boot".
What can I do to make my phone always start in the normal way?
Thanks!
Nakkie27 said:
Ok all, got it finally working again!
Don't ask me why, but flashing the newest Dutty ROM (and the included radio) did work.
Thanks for all your help, and a wonderful evening!
Click to expand...
Click to collapse
i smell a radio issue - last time i was trying to upgrade my radio - ended up with something similar, managed it out like you did - but now you're up - so that's good!!
try some other rom (this time without radio) - i don't think you should have any issues going forward... good luck and have fun!