Develop Bugs

When installing WM6, ActiveSync auto disconects. What to do?

Hello everyone.
I have just bought my Hermes (AT&T 8525) after one year of planing so. It came with WM5. I downloaded some of the ROMSs, radio and bootloaders commented here. I tried reading all the vast infromation in this forum and the wiki, but still having a problem.
THE PROBLEM IS AS FOLLOW:
When I start the flashing process, using HTC_TyTN_WWE_3[1].54.255.3_6275_1.48.00.10_108.exe or RUU_Hermes_CINGULAR_WWE_3.1.57.502.1_6275_1.48.00.00_108
... everything goes well, until the progress bar appears in my PC. When it appears, ActiveSync in my PC closes and my Hermes goes to stand by (the lcd goes off) so I cannot complete the installation process.
The phone works pretty well and I'm really amazed for all its capabilities. But still, I'm stucked with wm5.
Why do you think this happened?
PS: I flashed the radio (1.51.00.10) and bootloader (HARD SPL v7). My ROM version is 2.15.502.3. I use "ActiveStink" to sync my files without problems.
Any advice will be more than welcome!!

I'm no expert but that appears to be normal behaviour!
ActiveSync is only used at the start of the process. After a few files have been transfered, Activesync is closed and a different link is established. If you just leave it for a short while longer, a progress bar should appear on the Hermes too.

Yes, ActiveSync will disconnect. The RUU takes over the connection. Have you let it sit - sometimes it takes a minute for the progress bar to move.
Have you consulted www.mrvanx.org for help on the flashing?

todd_jg said:
Yes, ActiveSync will disconnect. The RUU takes over the connection. Have you let it sit - sometimes it takes a minute for the progress bar to move.
Have you consulted www.mrvanx.org for help on the flashing?
Click to expand...
Click to collapse
I'm having the same problem - always have. The message tells me that I'm disconnected and that I should check my USB connect etc. I left that box up there for about 15 minutes. Now I've closed the box and have waited several minutes with no activity. This is pretty aggravating. Thanks for any help.

try turning off your antivirus aplication. thats work for me flashing my tytn to wm6.

I've done everything.... I guess
Hi...
Yes, I consulted the www.mrvanx.org, excellent tutorials.
I flashed without problem the radio and bootloader. The progress bar started to "progress" and everything was fine. The only problem I have is flashing the WM6.
I don't remember where, but I readed that flashing the bootloader "Hard SLP v7" causes my HTC not to accept any Oficial WM6 ROM. The article said that I only had the chance to flash a coocked or modified ROMs. Is this true?
If not... what else can it be? I also closed all my applicacations including the antivirus, goback, disabled the internet connection, the logictec mouse center, etc. and nothing, the same as Chicoh happens to me.
"Error 260: Connection... check the USB cable bla bla bla."
Should I restart in safe mode to do the flashing?
Should I try to install a modified ROM?
Have in mind I've tried three different official ROMs: WWE, Cingular and spanish.
Thanks to all the comunity!!!
Saludos desde México!!

Greetings -
I had a similar problem and couldn't get the thing get going. My solution was to load it from the SD card. This worked flawlessly.

liquidsilver said:
Greetings -
I had a similar problem and couldn't get the thing get going. My solution was to load it from the SD card. This worked flawlessly.
Click to expand...
Click to collapse
I'm trying that as we speak. I have a good feeling about this. I'm a little concerned that I didn't think of it though. Makes perfect sense - Skip the middle man.
UPDATE: Crap. No luck. Thanks all the same though. I'm not giving up.

What OS are you using, xp or vista? My vista 'top had the same problem wouldnt flash for the longest time and i had to use my xp.
However, it does work now. Not entirely sure why.

Now I had success!!!
Hello my friends.
It seems that the article I readed days ago detailing that after flashing the Hard SPL v7, I could only install a modified ROM, not an official one from HTC or Cingular.
I downloaded Black Satin and installed it without any troubles. The entire process lasted only 3 minutes!!!
I wanted to have an official ROM, don't ask me why, and never tried the "other" ROMs that are actually excellent!!! some apps that were on WM5 are not in WM6, which is kind of sad, but if there's something that I love of WM Smartphones is that I can download and install whatever I want or develop it if it doesn't exist!!!
By the way, I use Windows XP Pro.
Thanks for all the support!!!
PS: Before flashing the Hard SPL v7, I tried installing the cingular WM6, but didn't make it. That's why I readed almost all the pages and threads here in xda-developers and found that flashing a new bootloader was a very good idea. The rest of the story is known by you.

custom roms and 6.5

i have a custom rom with a 3.42 radio and wm 6.1
if i upgrade my phone to windows mobile 6.5 will i still have my custom rom or would it be all new just like when you flash a new rom?

jljohnson919 said:
i have a custom rom with a 3.42 radio and wm 6.1
if i upgrade my phone to windows mobile 6.5 will i still have my custom rom or would it be all new just like when you flash a new rom?
Click to expand...
Click to collapse
The only way you would be able to upgrade to WinMO 6.5 would be to flash the phone just like when you flash a custom ROM now
WinMO 6.5 is not an installable app/upgrade like upgrading an application on your phone its the operating system itself
Right now and there are very few ROMS out there for WinMO 6.5 and none for the Vogue at all (Im assuming you have a Vogue as this is where you posted) soon there will be one as there are people working on it currently but what is there is EXTREMELY buggy and almost non-functional for the fact its on a phone and a phone should be able to be used after all LOL
Keep with the Custom ROMS for now and wait, the desire for it has been spoken and the Chefs are a cookin LOL
Detroit Doug

NFSFan has confirmed that those WM 6.5 ROMS are FAKE. Even if they were real, there would be no point of using them...

The builds are fake indeed. However they do contain a few components of 6.5. None which are worth upgrading for.

NFSFAN said:
The builds are fake indeed. However they do contain a few components of 6.5. None which are worth upgrading for.
Click to expand...
Click to collapse
Really? What components do they have? Anything from a new today screen or Internet Explorer (like rumored)?

Kinetic scroll (give up TouchFLO and Manila2D), new IE build that supports kinetic scroll. The today screens being posted are fake. They are actually from a smartphone, called HTC Juno. Some asian dude took it out of the Juno, resized the images, and re-arranged the tabs to make it look like the new today screen.

flashing on Vouge
I know this may sound tedious but i have no idea on how to flash any ROM onto my Vouge. Can someone please help. I would love to try out several ROMs and see which one would work best for me.
Thanks in advance

Hey, here is one really good one
Detroit_Doug said:
Basically here are the steps
Download the 2.31 unlocker
Download the ROM you want to use (my personal preference is this one for a TF2D style or this one for a WinMO 6.5 style interface that has TF2D included to switch back and for - both very stable, fast and clean and the thread is very active for help (especially if your on Verizon or Bell which can have issues)
from there, use WinRAR to extract each file into separate folders
then Put your phone in bootloader mode (press and hold power+camera+stylus in reset until 3-color screen comes up)
At this point at the bottom of the screen it will say Serial, plug it into the USB cable or cradle and it should change to USB
Start the exe in the 2.31 and follow the directions (you may get some errors about sleep4.exe just click on OK as it keeps occuring its a XP/Windows7 64 bit issue if that is what your using)
At the point where it tell you to disconect, unplug the phone from the USB cable and wait (count to 10 or something) then plug it back in, it should have went from USB to SERIAL and now back to USB at that point go ahead and hit any key on your PC and it should continue along
once complete, reboot, allow it to do its thing then reboot and go back into bootloader again during reboot you should see coke 2.31 in the upper left if so your ready to go
plug it into your USB/Cradle again and then go into the ROM folder you extracted the ROM into
Once the screen on your phone says USB again go to the folder and double click on the RomUpdateUtility.exe file and follow the directions again, it may take some time so be paitent
once the phone flashes and reboots, let it run and do its thing to the and reboot itself then (and here is an important step for stability) once it starts up do a hard reset (red+green+stylus in reset hole) hit the enter button (center of D-Pad) it will reflash the phone and then red key (send) when prompted
then go thought the setup again, this time you can actually set things up as your keeping them this time and once things are done and your at the start screen on your phone power off (not reset) the phone and then start it up again - seems doing it this way takes care of alot of little issues that will come up before they can happen
Depending on your carrier be sure to have one of the DCD Carrier Cabs as well especially for the 6.5 ROM as it is a generic ROM and some have reported needing to run the DCD Carrier Cab for the service they use to get on the internet and use GPS and the like
Detroit Doug
Click to expand...
Click to collapse

thanks
Everything is working smoothly and better than I thought it would have (i flashed the 6.5 ROM). Thanks to you Detroit Doug or I don't think I would have been able to do it without your instructions. I however do have one more question....i'm having issues syncing the device with my PC now. Any idea on what that could be???

re: Thanks
I've done several resets but to no avail am i able to connect via active sync???

OK maybe i lied about everything working properly and wonderful....so on top of not being able to connect to my PC via activesync I also am not able to connect to the internet on my device, i've downloaded and installed the NFSFAN Sprint GPS Registry but still its a no go... Did i do something wrong completely????? still

I fixed the internet problem!!!!!!!!!!!!!!!!!!!!

....somehow magically i'm now able to connect via activesync. I guess the device just needed time to adjust. Thanks for the help, and i do apologize for the numerous newbie questions.

ehepps said:
....somehow magically i'm now able to connect via activesync. I guess the device just needed time to adjust. Thanks for the help, and i do apologize for the numerous newbie questions.
Click to expand...
Click to collapse
ok so i didnt notice this thread. so whats your secret? howd you get it to work?

mbaseball, I just replied to your thread.

MMS
I flashed the rom perfectly and im lovin every thing bout it but one thing, i cant send or recieve picture mail. Is there a way 2 fix that or sumthin. That takes alot of funny away from the rom. help me please. does there happen to be a 6.5 rom wit picture mail?

Best Windows Mobile 6.5 upgrade for Vogue (Bell)?
hi
I 've been reading this thread, and am just wondering whats' the best download so far for upgrading to Windows Mobile 6.5, for HTC Touch - I think this is the vogue...for Bell Mobility?
If you could please provide a download link.
Thank you all for your help
Thank you
Karim

kchaggani said:
hi
I 've been reading this thread, and am just wondering whats' the best download so far for upgrading to Windows Mobile 6.5, for HTC Touch - I think this is the vogue...for Bell Mobility?
If you could please provide a download link.
Thank you all for your help
Thank you
Karim
Click to expand...
Click to collapse
The best is NFSFAN's Windows Mobile 6.5 ROM. You can find it on another thread in this forum right here:
http://forum.xda-developers.com/showthread.php?t=432487
Don’t even bother with anything else. I am running this. It is fast, stable and very close to the stock WM 6.5 (I have downloaded the device emulator image from Microsoft’s website for software development purposes). The extras that are in there are useful.
The Fish

How to install NFSFAN's custom Roms

Hi i was wondering if there was anyone out there who was kind enough to explain in detail how to install this Rom because by the looks of the pictures and the reviews, it is a great Rom. OH and if there is an answer to this already, please direct me to it because i have searched for hours and cannot find anything.
Thanks in advance

How far is your knowledge when it comes to custom ROMs? Do you have your phone unlocked?
If your phone isn't unlocked, go here:http://forum.ppcgeeks.com/showthread.php?t=20370

I could use a little help to. My phone is unlocked and I have flashed another rom before but when I download the rom file I can't do anything with it. I seem to remember using another program to handle the rom file before flashing but I have looked and looked and have come up empty handed. Someone pointing in the right direction would be great.
Basically I am stuck between getting the file on the computer and starting to flash. I can get my phone to the color screen and all.

Terms you should know before-hand, haha:
-The color RGB color screen is called the Bootloader mode (you get to it by holding the power button + camera button, and sticking you stylus in the slot at the bottom of you phone to reset.)
-Hard-reseting: Flashing the phone to default state of the flashed ROM. (Hold talk key + end call key, and sticking you stylus in the slot at the bottom of you phone to reset.)
-Soft-reseting: Simply restarting your phone. (Sticking you stylus in the slot at the bottom of you phone to reset.)
-------------------------------------------------------------------------
0. Unlock Phone. (http://forum.ppcgeeks.com/showthread.php?t=20370)
1. Go in to Boot-loader mode. (Text towards the bottom of the screen
should read "Serial" if you phone isn't connected to the PC.)
2. Connect phone to PC. ("Serial" text should change to "USB")
3. Extract the files from .rar file you download. (Use Winrar.)
4. Run ROMUpdateUtility.exe and follow the on screen instructions.
- Your phone will start showing a progress bar when the flashing starts.
- Once done, the phone will restart. (Should reset and windows should boot, but still do step 5.)
5. Hard-reset the phone.
6. Dance in place.
-------------------------------------------------------------------------
*pants* Hope that helps!

Stickfigure, thanks a bunch for your summary of the ROM loading process! My Sprint Touch has been giving me lots of problems (freezing on incoming calls, data connection stops working randomly, phone not wanting to get out of roam and back into EV mode, and many many more). Needless to say, it is frustrating and I want to throw it at a wall. I'm sure my reset button is going to fail since I've poked it so many times.
Anyways, I've been wanting to install a custom ROM and finally have the chance during my spring break from classes, but I wasn't quite sure how to do it. Your post definitely helps.
One more question...is the process basically the same if I want to install a different custom ROM? If you know of any other tutorial or noob info pages that might help me I'd appreciate it too.
Thanks again!

Stickfigure, thanks for the instructions. Winrar was the piece that I was missing. Once I installed that I had the new rom installed the the phone was working fine in a bout 15 minutes.

hapa_dude said:
Stickfigure, thanks a bunch for your summary of the ROM loading process! My Sprint Touch has been giving me lots of problems (freezing on incoming calls, data connection stops working randomly, phone not wanting to get out of roam and back into EV mode, and many many more). Needless to say, it is frustrating and I want to throw it at a wall. I'm sure my reset button is going to fail since I've poked it so many times.
Anyways, I've been wanting to install a custom ROM and finally have the chance during my spring break from classes, but I wasn't quite sure how to do it. Your post definitely helps.
One more question...is the process basically the same if I want to install a different custom ROM? If you know of any other tutorial or noob info pages that might help me I'd appreciate it too.
Thanks again!
Click to expand...
Click to collapse
There are some great tutorials out there for beginners, one of the best of which is Dharvey's "UPDATED- CONSOLIDATED Rev A./GPS TUTORIAL" found on PPCGeeks; it is no longer available for some reason, but you may be able to find a repost somewhere.

Thanx
Thankx every one who contributed to this thread because it really helped.

ROM Recommendations (see inside)

Hey there,
After lots of problems with my P3300 (see this thread), I've decided to flash it to see if that helps. I'm not too bothered about getting the GSM working again as I have another phone, but I'd like to be able to run all apps again.
So... I'd like some advice please.
What would be the best ROM for me to use if I just want to use the phone as a GPS device, portable wifi web browser and notepad?
Basically something pretty stripped down with as good battery life as possible.
Is there any advantage with going for WM6 over WM5?
Bear in mind I've never done this before and am currently reading up on all of it.
From what I've read so far I'll have to do the CID unlock first (currently have WM5 in french installed and would like an english ROM)? I think it may be unlocked already but am not sure. Is there a way to check? Do I risk anything if I run USPL even though the phone is already unlocked?
Thanks in advance for any advice!

You can check if your phone is CID unlocked if the SPL number which comes up while booting during the big white HTC screen says 1.11.0000. If it says anything other than that then it's not unlocked.
Best stripped rom for me is Sheen's clean base version 3. Check it out, it's on the first page of the thread.

alternatively, if u want fast and stripped, go for yues extraclean (see my signature)
greetz

ferfecir Clean
This is the best clean rom which is a modified version of Yues clean with 30mb free ram.
http://forum.xda-developers.com/showthread.php?t=531972&highlight=ferfecir

mta33 said:
This is the best clean rom which is a modified version of Yues clean with 30mb free ram.
http://forum.xda-developers.com/showthread.php?t=531972&highlight=ferfecir
Click to expand...
Click to collapse
Pagepool 4 MB
RAM 32 MB
ROM 69 MB

Thanks for the replies. My SPL says 1.12.0000 so I guess I need to do the CID unlock.
Ferfecir Build 20931 looks like the most promising from those.
Can anyone please point me to a good tutorial for flashing the ROM via activesync? I'd rather not have to format the memory card if I can avoid it and my soft reset button is broken. (I have serached but had no luck)
Thanks!

download uspl from here http://forum.xda-developers.com/showthread.php?t=311403
and any rom you want...
unpack the uspl
plug the cable in the device and establish a usb connection
run the "start_uspl.exe" be patient...after being prompted to click some "next buttons" follow the procedure...and i mean it...follow the procedure...that with 50% battery,no programs running on the pc,no unplugging the cable and so on...
and you will have the uspl flashed
go to boot loader...The bootloader is invoked by pressing down the Power and Voicedialer buttons simultaneously, and using the stylus at the same time to press the RESET button at the left side. Continue pressing the two buttons for a few seconds after pressing and releasing the reset button until the bootloader screen appears.
if uspl says 1.11.000 then you are good to go
now you can flash any rom (cooked for artemis) and any artemis radio (i recommend you the 3.34.90.) onto your artemis
simply download,extract,run the rom update utility (RUU) ,follow the procedure and watch the show...
if you ever get an error during flash or anywhere else in the rom update utility...refer to this page and troubleshoot your troubles http://wiki.xda-developers.com/index.php?pagename=RUU_Errors
if you get an error saying invalid file size or something like that (you will get it if you try eg this rom..http://forum.xda-developers.com/showthread.php?t=465291)
go to this thread http://forum.xda-developers.com/showthread.php?t=521406 download the file and flash it if it is an ordinary rom...just run the RUU
afterwards just check it in the bootloader if it says 1.11.cmon it is ok....and you will be able to flash virtually any rom cooked for artemis onto yours

i must be damn crazy to post this thing...because it is all there in the wiki and the forum stickies,believe it or not

Thank you very much for the detailed instructions.
Just two more questions!
My reset button is broken. Can I just turn the phone off and back on to check if I have 1.11.0000 instead of using the bootloader?
And the RUU is this one? http://code.google.com/p/htc-flasher/downloads/list (only file I have for the new Ferfecir ROM is a .nbh, is that all I need?)
Thanks again.

this is a very open-ended question.
Everyone on here will have their own favourite rom....if there was 1 definate fits-all "best" rom ...everyone would be using it..but there isnt and we are all using the rom that suits us best
some people want their phone to be more like an iPod and so the multimedia aspect is a priority along with decent graphics and animated menus
some people want the PDA functionality most so they want a really stripped-down fast rom that is reliable and handles email well
everyone wants to use it their own way....thats why this site exists.
The guys who make these ROMS are the guys who say "this is good, but i want it to be more like THIS."
Follow farukb's (excellent) instructions....unlock your device properly....if you get any problems, search for the answer before asking for help....chances are hundreds of people will have had the same problem and hundreds of people will have already given the answer...and then ....just look around the site. See which roms are available that fit YOUR needs, and flash it....if you dont like it, try another.
I'm trying 6.5 roms at the moment and love it....i've flashed it probably once a week with a new ROM each time a new version is released and have seen the OS evolve....right now i'd say PDhee's Mega 6.5 M2D rom is the best of the bunch providing you're not planning on installing LOTS of exra programs.
that's the beauty of these things, if you dont like the ROM, just try another. Sometimes the ROM won't work quite right (especially if flashing ROMs between different cooks) so just try flashing it again to make sure it resets everythin correctly. If it's still not right, try a different ROM.
farukb said:
i must be damn crazy to post this thing...because it is all there in the wiki and the forum stickies,believe it or not
Click to expand...
Click to collapse
yeah, unfortunately (and it seems to have increased over the last year or so) nost people on here are noobs who can't be bothered to read through some threads or use the search and we just get the same questions asked constantly.
I dont minds helping people....providing they've looked for the answer themselves first.
every time a new rom is released there will be people asking what error 260 or 270 means?, do they need to USPL? etc etc
it's easier to ask someone else to take time out of their day to aswer your question than just type "error 260" into the search box and find out for yourself. They dont consider that people are having to answer these questions 10 times a week, in their own time, for no thanks, just to have the same question asked the next day. Purely becuase they couldn't be bothered to see if anyone else has asked that question before.
sorry...rant over....i love you all

seebasso said:
Thank you very much for the detailed instructions.
Just two more questions!
My reset button is broken. Can I just turn the phone off and back on to check if I have 1.11.0000 instead of using the bootloader?
And the RUU is this one? http://code.google.com/p/htc-flasher/downloads/list (only file I have for the new Ferfecir ROM is a .nbh, is that all I need?)
Thanks again.
Click to expand...
Click to collapse
no
you need to use the reset button (stick the stylus in the reset hole) .
Reset is like turning your computer off and on again
Power button is like turning the monitor off....it doesnt stop programs running and it doesnt properly reboot the device.
Your only alternative is taking the batter out i think (just like pulling the plug out will also reboot your computer).
If you havent already run USPL, then you probably WILL need to do it.
i dont know the specific ROM you're talking about, but just an NBH file will NOT work. You need the EXE file to run it.
Just download any suitable ROM off this site and it will have the whole package....if you're downloading from another site you'll have to ak that other site for help

my reset button doesn't work. i took the phone apart to change the touchscreen and must have misaligned something when putting it back together. sticking the stylus in the hole doesn't do anything anymore. will take the battery out instead, thanks.
regarding the rom, it is one i downloaded from here: http://forum.xda-developers.com/showthread.php?t=531972&highlight=ferfecir
the rar file downloaded from 4share (http://www.4shared.com/file/112067347/72728603/ARTEIMG-Ferfecir_-_20931_en_gncel_hali.html) only contains the nbh, no exe.
and for the record, i've spent all afternoon/evening researching this, searching this forum and the wiki etc! i appreciate it's annoying answering the same noob questions over and over again but i thought my thread was specific enough to warrant it and am grateful for all the replies.

seebasso said:
regarding the rom, it is one i downloaded from here: http://forum.xda-developers.com/showthread.php?t=531972&highlight=ferfecir
the rar file downloaded from 4share (http://www.4shared.com/file/112067347/72728603/ARTEIMG-Ferfecir_-_20931_en_gncel_hali.html) only contains the nbh, no exe.
and for the record, i've spent all afternoon/evening researching this, searching this forum .....
Click to expand...
Click to collapse
...yeah, and if you read ferfercirs description fully, you will come past "sd-card-flashing" which is the way to flash the *.nbh -part of your rom in a way without needing an activesync connecton
greetz

i did read that bit
but as mentioned a couple of times in this thread already, my reset button is not operational so i cannot use bootloader (afaik). so i assumed there was another way.
but i guess i'll find a rom that comes an an exe and save myself some trouble

no need to keep searching,
u can simple take the provided *.nbh file that came without an exe, rename it to ruu_signed.nbh, exchange the existing RUU from a complete installer-routine and off u go, provided u have used uspl first
greetz

ok thank you once again, i'll try it tonight.
one final question! do i need to have a sim card inserted while running USPL or does it not matter?

It is recommended to remove both your SIM card and your MicroSD card during any type of flashing, whether it be USPL or ROM. Even my reset button is not working anymore, my phone got dropped in water and I had to give it for repairs. After motherboard change they assembled it slightly wrong I guess, and it doesn't work. But I can still get into bootloader by just pressing the Voice record and power buttons together for 10 seconds. Try that.
Secondly, I hate to be plugging myself here, but I have just cooked a clean 6.1 ROM myself, with the latest build of 6.1 that is 21054. you might want to check that out, it comes with the full package and not just the nbh
here it is - (http://forum.xda-developers.com/showthread.php?t=551728)
Again, sorry, but Im giving you an option thats all

thormdac said:
no need to keep searching,
u can simple take the provided *.nbh file that came without an exe, rename it to ruu_signed.nbh, exchange the existing RUU from a complete installer-routine and off u go, provided u have used uspl first
greetz
Click to expand...
Click to collapse
ok i need help again sorry! i tried this but i got an error after 5% saying the .nbh was an invalid size
i used the ROMUpdateUtility.exe from Arte_WM65_23009_M2D_Mega_beta1 ROM (i removed Arte_WM65_23009_Mega_b1.nbh from the folder and replaced it with Ferfecir's .nbh which I had renamed to ruu_signed.nbh)
What did I do wrong?
I ended up flashing with Arte_WM65_23009_Mega_b1.nbh and it worked great but that ROM is too much for me and I want Ferfecir's simpler one.
Thanks

You need to flash the newer USPL which allows nbh files of a smaller size to be flashed.

thanks! it worked. everything working perfectly and my gsm works again too. woohoo.

Keyboard still not mapped correctly after cab install!

I was not the only user having this problem. There was actually a bounty set for a fix, but I havent seen one yet. Flashed Energy Rom Sense 2.5 and 2.1, provisioning didn work, and neither did cab install for correct key layout. Numbers still across the top row, and most symbols still incorrectly mapped. Seems to be first tilt configuration and nothing will change it back.
The strange thing in my case was before I ever flashed ANYTHING SPL, ROM radio...anything...,(bone stock) my HW keyboard would auto remap to these settings out of nowhere. Two different devices had this problem, i took the first one back, and this one being the second. a soft reset would set configuration back to stock before flash, but now even the cabs available will not change anything. I got a $20 for a .cab fix or a detailed xplnation of how to fix this, and have the entire HW keyboard mapped in english and to at&t tilt 2 configuration that will work on this device
Please Forgive the rant in the prior post concerning this issue, as this has become quite frustrating lol, and I have owned every HTC device at&t has sold and loved em all, but had to hunt fixes for every single one. Ive learned a lot in the process, but sometimes time is limited to be able to constantly search for what would seem to be a simple fix. If you will notice, for as long as long as I have been a member of this great community, I have made very few posts, and asked few questions on my different devices ...I read searched and read some more. I had xda google search as my homepage for a loooong time, help on this issuue would be greatly appreciated!!!

What cab did you use? There's a few floating around. I've tried dozens of roms and only seen this issue with one or two ROMs (both 2.5 roms) but went away after a hard reset. Are you hard resetting your device after flash?

Toleraen said:
What cab did you use? There's a few floating around. I've tried dozens of roms and only seen this issue with one or two ROMs (both 2.5 roms) but went away after a hard reset. Are you hard resetting your device after flash?
Click to expand...
Click to collapse
mskip said:
1. Make sure your microSD is Formatted to fat32 (you dont have to delete all files but it is safer if you do)
2. Download your prefered Rom from the Rhodium Rom Develpoment Page and unzip/unrar it to your PC
3. Goto the Roms Folder and rename the .nbh file to RHODIMG.nbh
4. Copy the RHODIMG.nbh file to the root of your MicroSD Card
5. Plug the MicroSD Card into the phone
6. Enter the BootLoader screen, you will first see a tri-color screen with the phone and SPL Information at the top
7. Follow the On Screen instructions to start the update
8. After flash has completed, press the reset button with the stylus to reset the device.
Click to expand...
Click to collapse
I thought it odd not to have to do a hard reset as left out in tutorial. I should have done it out of habit from flashing kaiser, and fuze, but no. I did not hard reset. I will try a new flash and do the reset this time. Hopefully thats all thats the problem! thank you very much, and cross your fingers for me lol. If it works I will def keep my word on 20!

DaIn BrAmAgE said:
I thought it odd not to have to do a hard reset as left out in tutorial. I should have done it out of habit from flashing kaiser, and fuze, but no. I did not hard reset. I will try a new flash and do the reset this time. Hopefully thats all thats the problem! thank you very much, and cross your fingers for me lol. If it works I will def keep my word on 20!
Click to expand...
Click to collapse
Just to help troubleshoot after you hard reset just install whichever keyboard cab you're using, soft reset, and test it out before installing anything or syncing.

thank you thank you thank you!
I cant believe thats all it was! Even more so I cant believe I didn even try the H R after flash. I never once failed to do this when flashing any other device, I guess b/c it was in the directions for noobs to do so in other forums, lol may ought to suggest adding it to the dir for flashing tp2 lol!
THANK YOU BIGTIME, once again! I had become frustrated after tryin multi cabs and reading where it worked for everyone else. all i did was re flashed, h-reset. cab was in uc folder, but that didn work, ended up using att provisioning provided by NRG, and there she was...working like a charm again!

Glad to hear it worked! Thanks for following up to, you're the first person with this issue I've tried helping that actually posted a followup.