need help for cricket internet!!!! asap - Touch CDMA Windows Mobile ROM Development

as i stated in an earlier post i have what once was a telus issued htc touch p3050 which i have been informed is the same as a 6900. i took my phone to a local phone flasher and was given back a partially flashed phone. to make outgoing and recieve incoming phone calls the phone works great!! however when i try to connect to the internet... i follow all the setup rules of the wap.cricket.com, [email protected], and port 8080 etc...
when i try to connect it tells me i have a bad username or password.
the phone attempts to dial the #777 too.
ok now here are some mitigating factors i should tell u about...
-when i soft reset the phone i get an alltel slash screen even tho the phone operates on the cricket network.
-when i go into the settings to futz with the internet settings i also get choices for an alltel phone.
-and as told earlier by a few folks i checked in my pst settings and my phone is in fact already on the simple ip settings...
please help!!!!
i really want and need internet!!!
i would be willing to try and reflash the phone with another rom but i can't get the qpst to recognize my phone... cuz it only allows me to open one additional port in addition to the two that already exist...i keep getting a port busy error...
thanks in advance!!!

tbananaz said:
as i stated in an earlier post i have what once was a telus issued htc touch p3050 which i have been informed is the same as a 6900. i took my phone to a local phone flasher and was given back a partially flashed phone. to make outgoing and recieve incoming phone calls the phone works great!! however when i try to connect to the internet... i follow all the setup rules of the wap.cricket.com, [email protected], and port 8080 etc...
when i try to connect it tells me i have a bad username or password.
the phone attempts to dial the #777 too.
ok now here are some mitigating factors i should tell u about...
-when i soft reset the phone i get an alltel slash screen even tho the phone operates on the cricket network.
-when i go into the settings to futz with the internet settings i also get choices for an alltel phone.
-and as told earlier by a few folks i checked in my pst settings and my phone is in fact already on the simple ip settings...
please help!!!!
i really want and need internet!!!
i would be willing to try and reflash the phone with another rom but i can't get the qpst to recognize my phone... cuz it only allows me to open one additional port in addition to the two that already exist...i keep getting a port busy error...
thanks in advance!!!
Click to expand...
Click to collapse
you realy need to just flash it yourself with a new rom... check your radio (3.35 & up) and then switch to one of vetvito's roms. after you flash it remember to set the phone todiag mode (##3424) so qpst will see it. you might need to change the port via the device manager. make sure you have the drivers you need (ppc6700 drives work fine)... Do ur *228 stuff after you change the spc to all 0's. if ever in doubt ##778 to check your epst settings. for internet, setup ur modem & proxy in the connection manager. be sure to use your real number and "cricket" as the pw. This is not a full walkthough, but the just main points you need to touch on.
good luck

make sure all ur epst settings are correct...check and see if u have the newest prl uploaded 1050 i believe is the new evdo one...also go to select networks in the connections/connections/advanced and make them all to the one u want to connect through

do u know where i can get the new prl. i installed the 1040 and its only 1X

Cricket on HTC Apache PPC6700
I have the PRL loaded. Internet is a b*tch! Every time I do a soft reset, the sprint connections come back. Then I have to delete the Sprint one, and goto the wap.... whatever whatever site to get it on the internet. And its only 1X. Here is a link to PRL's. http://corolada.com/prl/
If ANYONE out there is willing to make me a Cricket rom for my 6700 Apache, you will be my best friend. It would be nice to not have to load a random PRL every time i hard reset my phone and mess with connections forever just to get slow as heck 1X speeds. If you can, just make a rapidshare link to the exe. Helmi's WM6 rom is bad and doesn't work right. And I don't know how to use BuildOS and my friend has used it several times on his VZW apache. But it won't work right for some reason. All I am asking for is a rom or cab or something to get internet to work. i don't even care that much about mms. even tough it would be nice

@tbananaz: Go to Howardforums.com under the cricket forum and looks for To0's V2 ROM for the 6900. You might have to PM him for it. Out of the box its has everything for cricket aside from changing a few things under EPST. The easiest way to get your phone working with everything with Cricket.
@disturb3d1: Your best bet for the 6700 would be to build a ROM for yourself for Cricket. Download PPCkitchen and make one. Its pretty straightforward and has everything including Crickets OEM info. So you don't have to mess with any other carriers settings.
If you any of you need help let me know. 8)
Later Days,

Related

Someone, anyone please HELP with an ESN

I know I'm a noob, but I've been struggleing with this for a while now. I put in probibly 6 hours last night and haven't any clue if I'm even close to being complete.
I bought an HTC Touch MP6900SP (Sprint) and was told it had a clean ESN. Turns out it didn't and I'm up the creek because I paid cash. I bought it to replace my motor razr which has a clean ESN, but is quickly dieing. I'm trying to clone my ESN but can't get mtty to work properly. Once the ESN is swapped, the RAZR will go in my junk drawr.
I've tried to follow the steps here:
http://www.mobile-files.com/forum/showpost.php?p=355768&postcount=1
but when I go to fire up mtty I can only enter the rtask a command then the program or phone won't allow me to do anything else, even type the next command.
In the boot loader I have the following info:
VOGU100 MFG
SPL-2.31.CoKe
CPLD-3
Can someone please walk a noob through this. I'm totally new to this whole unlocking thing and could really use some help. The phone is locked to the account of the previous seller who refuses to release it. I've got the 2.31.coke on there now and when I boot it normally I also have the Alltel rom that fires up. HELP!!! PLEASE!
Edit: In MTTY when I run rtask a this is what I see, but I can't type anything after that.
rtask a
Enter Radio Bootloader
POWER ON PMIC VREG_USB : SUCCESS!
This has been covered...
SEARCH!!! MTTY is actually working, you just can't see the text you are typing... Just be careful typing everything in and you will be good to go...
Alright, I got through MTTY, and am not onto working in CDMA workshop.
I put the phone into DM mode, Active sync disconnects, but CDMA shows it is connected to Com1 port successfully, but fails when I attempt to read the ESN.
I can't seem to find the diagnostic modem drivers that I need and think the lack of the drivers is what is causing me grief now.
Believe me, I'm looking everywhere I can to get information. I've got tons of hours into this now.
Edit: Got the drivers installed and working properly. Still having problems reading from the phone with CDMA.
Edit 2: Had to figure out the proper com port in CDMA, getting warmer.
scanning and finding esn addresses right now! If this thing works I'll be so damn happy!
im still reading up on this, but seeing information that has been corrected over time, then finding some old posts that may be outdated.
using MTTY with all of the steps to superCID... is that actually changing the ESN in one failed, fast swoop? Is it actually doing what CDMA does when scanning/writing?
ESN
cox abele said:
im still reading up on this, but seeing information that has been corrected over time, then finding some old posts that may be outdated.
using MTTY with all of the steps to superCID... is that actually changing the ESN in one failed, fast swoop? Is it actually doing what CDMA does when scanning/writing?
Click to expand...
Click to collapse
Hey did you get this to work? I changed my esn last night and the phone works. Can make and receive calls. Only prob is that I can't connect to the internet. I think it is a problem with the user name/password but not sure. I keep getting the 67 error when trying to connect. I only changed the esn and nothing else.
Did you have any luck? If so what about the internet thing? Any help would be much appreciated. Been reading and trying to figure this out for a while now.
Thanks,
-T
Hey man, welcome to XDA
What Airline do you fly for? It's good too see another fellow Pilot on here.
As you can see from my sigpic, I'm with Air Canada Jazz.
b727pilot said:
Hey did you get this to work? I changed my esn last night and the phone works. Can make and receive calls. Only prob is that I can't connect to the internet. I think it is a problem with the user name/password but not sure. I keep getting the 67 error when trying to connect. I only changed the esn and nothing else.
Did you have any luck? If so what about the internet thing? Any help would be much appreciated. Been reading and trying to figure this out for a while now.
Thanks,
-T
Click to expand...
Click to collapse
Have you tried installing the DCD carrier cab. I think this is the link. Just double check.
http://dcd1182.n715dp.com/index.php?dir=carriers/
Help with ESN Change. Phone works just not internet
Csquared said:
Have you tried installing the DCD carrier cab. I think this is the link. Just double check.
http://dcd1182.n715dp.com/index.php?dir=carriers/
Click to expand...
Click to collapse
Thanks for the reply. No I had not tried the DCD carrier cab. First of all let me get this out of the way. NOOB here.
I tried researching the DCD cab because someone else suggested it and then tried it and it didn't work. I think it might be something with the user name and password for vision service. This is what I did:
Flashed the Touch (it is a sprint touch) to the 6.1 wm latest rom (sprint). Then did the esn swap from my razr (also sprint). After the esn swap I flashed again using the 6.1 sprint rom (just wanted to make sure nothing changed after I did a rom flash). Phone works fine on sprint and I even called them on it and they think it is a razr. I can make and receive calls, voicemail etc. Just can't get the internet working. Just get the 67 error. Any ideas?
-T
jmitr said:
Hey man, welcome to XDA
What Airline do you fly for? It's good too see another fellow Pilot on here.
As you can see from my sigpic, I'm with Air Canada Jazz.
Click to expand...
Click to collapse
SWA! Ever in MDW?
-T
b727pilot said:
Thanks for the reply. No I had not tried the DCD carrier cab. First of all let me get this out of the way. NOOB here.
I tried researching the DCD cab because someone else suggested it and then tried it and it didn't work. I think it might be something with the user name and password for vision service. This is what I did:
Flashed the Touch (it is a sprint touch) to the 6.1 wm latest rom (sprint). Then did the esn swap from my razr (also sprint). After the esn swap I flashed again using the 6.1 sprint rom (just wanted to make sure nothing changed after I did a rom flash). Phone works fine on sprint and I even called them on it and they think it is a razr. I can make and receive calls, voicemail etc. Just can't get the internet working. Just get the 67 error. Any ideas?
-T
Click to expand...
Click to collapse
Do you have a data plan setup with Sprint on your Razr?
Csquared said:
Do you have a data plan setup with Sprint on your Razr?
Click to expand...
Click to collapse
Yea I have the old sero plan. It includes unlimited data. I think that is what you mean. I can run opera on it so it is working.
-T
This might be trivial but lets check.
Goto:
Settings/Connections/Connections/Advanced/Select Networks
It should show Sprint in top and Work network in bottom.
Click edit under Sprint and make sure its set to #777
Then try this:
Settings/Personal/Phone/Services/Internet/Get settings
Then have IOTA done by pressing start.
No Internet Still......
Csquared said:
Then try this:
Settings/Personal/Phone/Services/Internet/Get settings
Then have IOTA done by pressing start.
Click to expand...
Click to collapse
Thanks Csquared. I tried this and this is what I got. I also have posted this at http://forum.xda-developers.com/showthread.php?p=3413006#post3413006 . Not trying to double post but was getting some help over there also.
Phone is working great using the donor ESN but no internet. Here is what I've got:
- Sprint Razr (donor ESN phone) and Sprint Touch (Had bad ESN now has Razr ESN).
- Have Data plan on my Account.
- Did the changes from the original post and phone works fine (can make and receive calls)
- When I try and connect to the internet it gives me error 67, can not connect #777 and 1012 error.
What I have tried:
- Start/settings/services/internet/get settings/ and start IOTA.
- Tried making a new connection under start/settings/connections/connections and setup a new #777 connection.
- Changed Active Profile from 0 to 1 in ##3282#
None of this worked. Under ##3282# my settings are:
User Name:
Active Profile - 1
MIP_MODE - Mobile IP Only
User Name - (My Username)@sprintpcs.com
SPI MN-HA - 4D2
SPI MN-AAA - 4D2
ReverseTunnel Pref - Enable
Home Agent IP Address - 0.0.0.0 (for some reason it will not let me edit this setting)
Primary Home Agent - 0.0.0.0
Second Home Agent - 0.0.0.0
HA Shared Secret (HEX) – Blank
AAA Shared Secret (HEX) – Bunch of characters
Advanced:
ESN - Donor ESN (From Razr)
MSID - My Phone number
Not sure if any of this makes sense. I am just trying to get the internet working. Please let me know if anyone has any ideas. It does say "Preparing vision services" when I try to connect to the internet but always fails with error 67 Username and/or Password incorrect. Also get Cannot Connect Dialed #777. Also get error code 1012 could not prepare Vision services please try again later.
Thanks very much in advance for the help!
-Tony
Well I know this is prolly not the right thread to put this under however I am not sure which is and the person who started this thread is doing what I wanted to know was possible to do. And second I was wondering how to do it. I am completely noob on this. I did as he did and bought a new phone which ended up having a bad ESN.
I have a Nokia with Verizon and it broke. They wont replace it for me so I went and bought an LGVX9100M. I have been researching for around 4 hours now and cant find a thing if I can take the ESN from my Nokia which is clean and working and put it to the LG to make it work. I am not familiar with any thing that has to do with programming cell phones or using the programs. I am however a pretty quick learner.
Is there a way to do this? Is there a program I need or a way to just do it in the phone? IF I can do this with a program how do I do it and what stuff do I have to replace the numbers with?
Bad ESN's= Unrecovered lost or stolen property, or property with a bill due over its usage.
Helping with Bad ESN's, is like helping repaint a stolen car.
WR

Can't get migrated xv6800 back onto Verizon network

What started out as an effort to get my migrated XV6800 to operate on Verizon's data network has taken a nasty turn for the worse... Here is the long, sordid story, and I would really appreciate help in getting this device back onto the Verizon network.
This was originally a Qwest phone. I unlocked it and flashed it with a Verizon ROM, the file name is _Verizon XV6800_RUU_TITAN_VZW_WWE_3.57.605.1_RS_TITAN_3.37. 75_OM_VZW_ShipFULL. After I did that the customization routines did not run. Frankly, I don't know if they were supposed to or not, but they didn't.
I couldn't get the phone to connect to the Verizon network, even on *228. Eventually I applied a PRL and then I was able to connect to *228, and option #3 got the phone onto the voice network. I used it as my cell phone for two weeks with no issues on the voice network. Still, I wasn't able to get data working.
These are the things I tried while troubleshooting the data issue:
* Loaded the carrier cab from DCD
* Forced a CDMA only connection to download new keys
* Loaded the newest Verizon ROMs I found while at their website (this is the first time I saw customization routines)
* Told Verizon to switch me from pay as you go data to unlimited data (though it looks like they never turned this on)
* Tried activating my PDA with a different Verizon number, and then re-activating it with my original Verizon number
* Did a hard reset
It's those last two steps that screwed me. After I swapped the number off the phone I wasn't able to get it back. I could get to option #3, but it wouldn't let me activate the phone. Their tech support is no help and they are shocked when they look back at my account history and see that I was able to use *228 to get this phone on their network two weeks ago.
I then did a hard reset and got myself all the way back to the point where I was before I manually put the PRL in place. When I dial *228 I get the following: "Your account is not authorized to make calls to this phone number. I you would like to have additional capabilities added to your account please call customer service. Message 4, swich 691". I'm guessing that installing a PRL on the phone will now let me use option #3, because that's what made it work last time. However, I'm looking for instructions since I messed up somewhere in the process last time.
I just tried the following, but I get a recording saying they are unable to activate my phone at this time and then it tried to connect me to a person.
1. Install PRL
2. Install carrier cab
3. Install MMS cab
4. Run *228, #3
I know the person is just going to tell me that they can't help because their system doesn't recognize the ESN.
So what's the verdict, can I expect to get this phone back onto the voice network, will it ever work on the data network? Any help that anyone can offer in resolving this would be greatly appreciated.
Wrong forum? Should this have gone into upgrades?
moved thread by request of OP as Q&A forum did not provide answers nor does the OP expect it to.
Best regards,
Flar
Since being able to dial *228, have you called customer service to pull a new key for your device? When I upgraded a xv6800 rom I was not able to dial *228 until I did that. It was a bit of work getting it to pull the new key, but they did it. They first walked me through a manual registration process, then I think they tried to push it through and that worked.
Is your phone a Verizon phone? The pickle I'm in is that mine is not. When they ask me for the ESN they say it's unrecognized and that's pretty much it. They say they can't help me get it on the network because it's not a Verizon phone.
mfreema said:
Since being able to dial *228, have you called customer service to pull a new key for your device? When I upgraded a xv6800 rom I was not able to dial *228 until I did that. It was a bit of work getting it to pull the new key, but they did it. They first walked me through a manual registration process, then I think they tried to push it through and that worked.
Click to expand...
Click to collapse
Yep mine is a verizon phone. I am wondering if this is a new implementation, because I have flashed several roms before and never had to call them to get my phone activated until about a month ago. When you dial *228 does it allow you to do a phone programing, I think it is option 1?
No. 1, 2, & 3 all fail. I just called tech support again, hoping getting a new A key would resolve this. He told me he couldn't give me an A key unless the phone's ESN was in the system and the only way to get it in there is through *228, #3... Kind of a Catch 22.
His last suggestion was that I activate a different PDA on my number and see if maybe the computer is choking because my current phone isn't a PDA, and this one is. Kind of sounds like clutching at straws, but he said at this point I've done all that can be done, short of that.
I find really odd, and extremely frustrating, that I can't find anyone else who has been through this with a non-Verizon phone.
mfreema said:
Yep mine is a verizon phone. I am wondering if this is a new implementation, because I have flashed several roms before and never had to call them to get my phone activated until about a month ago. When you dial *228 does it allow you to do a phone programing, I think it is option 1?
Click to expand...
Click to collapse

Flashing Samsung Fascinate To Cricket Walk Through

Flashing Samsung Fascinate To Cricket!!!!
ok so this is the one phone that has made me wanna punch my screen since i got it. amazing phone but hell an a half an very difficult to flash. OK so to start there are programs out there u can purchase to flash this phone if u wanna pay 100 dollars or 65 at a shop. but well im cheap so i set hours on end figuring what i could out. this tutorial will get u talk, text, 3g, internet an ability to send mms (to recieve has been difficult because there is a lock code to get to those features that ive been unable to find out)...
WHAT YOU WILL NEED!!!
QPST. 2.7 build 323 an build 215.
a Samsung fascinate.
PATIENCE!!
samsung fascinate drivers
and samsung epic drivers
first you will want to turn on usb debug mode, stay awake while plugged in, mock location(applications /developer menu). o an dial up mode(in wireless settings). install all the drivers before plugging phone in. after that plug in the phone. now as always you will want this phone on COM PORT 1. . (if u dont know how to do this u have to get to control panel then systems then hardware tab then select device manager. from there go to ports right click the samsung. then port settings tab then advanced. there will be a number toward the middle bottom set it as com port 1 then ok ok ok ok untill ur back to device manager then exit device manager) open qpst system programming. phone should show if not go to qpst config an set it up.
now in qpst system programming u will select the phone an it will ask for the spc. it is six 0's (ZERO's). then select read phone . now go to the roam tab. then u will see a prefered roaming box click the browse button an select the prl you wish to use. (nationwide 3g prl is best i use 42800 which is for the zio) now write to phone it will restart.. from here after the phone restarts open up qpst again an go thru the first process except do not go to the roam option. click the cdma tab an select nam1 if not already selected(ONLY nam1 NOT nam2 if u r dumb enough to mess with nam2 i am not responsible for the outcome )in nam 1 select set to default. now go to m.ip an delete all entrys. click write to phone it will again restart..
ps after you load the prl to the phone do a factory reset to clear out a few of the system logs to help everything go thru smooth
FUN TIME!!!! after phone reboots click the dialer menu (if its asking to program push the power button as if u r turning it off then select airplane mode. then restart the phone while in airplane mode(trick to get around that pesky activation menu).now after that boot select the dialer an enter *#83786633 an press home. got back to dialer an delete whatever is in it. if nothing ok now enter *#22745927 it will then ask for the spc code it is six 0's (ZERO's). now select to enable hidden menu. from there accept an what not if it ask an get to the home screen after hidden menu is enabled.
now again enter dialer make sure its clear an press **772 it will again ask for spc it is all six 0's (ZERO's) 000000. now from there it will show a service programming menu. press down slowly till u reach nam1 CDMA directory number. this will be your number click touch here u enter your number (for example 937-000-0000) now after that press enter then the back softkey to exit keyboard then press the down button this will bring u to a screen where u can enter your min(if u do not know it call cricket an ask them to bring it up for u. easier to call a local store an get this info. after u enter it press the back softkey u should be on cdma home sid. u will need to know your sid or find it out (google is your friend an so is your cricket store employee's) . enter it then press enter an exit the keyboard an when u see the exit screen hit ok. phone will reboot.
now u will have to of course have your phone activated to go any further so u know that process. (ps u can also activate it after u get the prl on it but until u do the hidden menu process it wont be active)
u now have text an calling but here comes the advanced user portion lol.
GETTING 3G
u will need to get the backup restore apn app from the market place its free. (email me an i can send u a copy).
u will need to install it an then backup apn. it will save to your sd card. plug it in to the computer an copy it to ur pc.
open the file in notepad as administrator the file will have all verizon settings change them to cricket. here is an example of mine after i changed it to cricket
<?xml version='1.0' encoding='UTF-8' standalone='yes' ?>
<apns count="1">
<apn name="Cricket" numeric="310012" mcc="310" mnc="012" apn="internet" user="[email protected] " server="*" password="cricket" proxy="null" port="null" mmsproxy="null" mmsport="8080" mmsprotocol="null" mmsc="http://mms.mycricket.com/servlets/mms?x-cricket-mdn=937_000_0000" type="null" />
</apns>
where the phone numbers are those will all need to be your number. an my mnc is 012 yours may be different but thats an ideal of the settings that u need to change. next u will save that file an place it on your memory card over the original file (overwrite the one on your sd card). after that access the apn backup app an delete all apns(DO NOT DELETE THE BACKUPS U NEED THEM!!!!!)now click restore apn it will ask which one an restore the one u just modified). now here is the funnest part but if done right u will have 3g......
first u will need to use qpst to setup your m.ip settings. u must use qpst 2.7 build 323. u will change your settings to cricket settings. . i can not completely remember the steps but u can google them on this part but make sure u click ur profile an change your numbers to @mycricket.com instead of the verizon settings. after that change both the ha and aaa passwords to cricket an set the home address to 0.0.0.0 then set the primary home address to 68.28.15.12 an then set second home to 68.28.31.12. after this write to phone after restart unistall qpst.
now u will install qpst 2.7 build 215. an go thru nearly the same process but in the ppp config menu. in here u will change your numbers emails to @mycricket.com in the UM and AN tabs an set the passwords to cricket. make sure in the um u change the tethered nai number to your number @mycricket.com. then write to phone an after restart turn off dial up mode an WALA flashed your fascinate.
ALSO ON A SIDE NOTE TO FURTHER EMPHASIZE THIS when u get the phone activated be sure to tell them its a zio *wink wink* so it will register in the system as a zio which will help more after u get 3g up an running. an all features only work on the 55 dollar plan
SORRY IF I GET A LITTLE SLURRY TOWARD THE END IM HUNGRY AN NEED A NAP LMAO
PS MMS WILL WORK IF THE APN IS DONE CORRECTLY AS SHOWN ABOVE!! MINE IS OFFICIALLY WORKING SOLIDLY (INGOING AN OUTGOING)
help
Hi, I was wondering if you were ever able to get MMS to work. I took my phone to the store to get it flashed and I was so upset afterwords. They flashed it however my MMS does not work. I can not send any messages out and I can get them in only from certain people. I have had several people try to send me messages and I was able to get them in from a few. Please help if you can..
for some reason cricket did some updates to their midwest region an now occasionally you wont receive mms from t-mobile or verizon customers an random other carriers if the picture crosses the maximum image size criteria. its odd. i just have em send the mms to my google mail. i recieve 98 percent of my mms tho using handsent mms so download it from the market place
works perfectly
Ok so Im gonna start by apologizing for bringing up an old thread and stating that I am not a noob in the flashing game just been a long time observer but I can vouche that this works for flashing to boost mobile. Only issue is getting vm to work but as far as 3g and data thats a different story, its hell I onlly have 1x speeds with data as we speak.
BTW mms lock code is 500667 but be very careful as you can get locked out after many times of messing with it and fixing will make you want to smash the phone into a millions pieces. I can vouche for it personally. Now my advice is if you see anything verizon in there that is why your mms is not working do not edit it in there as it will just revert back to original after reboot. You have to complete debrand the phone in order to get these settings to stick and fix the mms lock out after many stupid attempts. GOOGLE IS YOUR FRIEND ON HOW TO DEBRAND!
Hope my first post helps out someone.
ability to send mms (to recieve has been difficult because there is a lock code to get to those features that ive been unable to find out)...
Click to expand...
Click to collapse
I stumbled upon this thread by a google search.. what a weird concept
Thought I'd contribute, I Don't know if it's been pointed out anywhere else yet- Samsung has been tricky with this for quite a long time. This specifically brings to mind my SCH-a870. The MMS lock code on Samsungs is typically 6 digits, the first three are the model number of the phone, the last three spell out MMS on a phone keypad. In this case, it would be 500667.
Good luck & happy hacking!
Now from what I am hearing is that you have to physically bring in a flashed cricket phone to a cricket store to have it activated. Cricket do not enter flashed phones esn information over the phone. Now does anyone know any other method of getting the phone activated besides going into a cricket store or sending your phone via snail mail to a remote person?
And someone mentioned boost mobile. Boot act funny towards adding non-boost mobile phones to their databases, so how are you people doing that?
I have a Fascinate on 2.2.1 There is no Dial up option & teather doesn't connect right... NE idea how 2 connect?
---------- Post added at 08:34 PM ---------- Previous post was at 08:08 PM ----------
Found it... Dial **USBUI change from PDA 2 Modem
boost mobile... fascinate/mexmerize
ir0b3rt809 said:
Ok so Im gonna start by apologizing for bringing up an old thread and stating that I am not a noob in the flashing game just been a long time observer but I can vouche that this works for flashing to boost mobile. Only issue is getting vm to work but as far as 3g and data thats a different story, its hell I onlly have 1x speeds with data as we speak.
BTW mms lock code is 500667 but be very careful as you can get locked out after many times of messing with it and fixing will make you want to smash the phone into a millions pieces. I can vouche for it personally. Now my advice is if you see anything verizon in there that is why your mms is not working do not edit it in there as it will just revert back to original after reboot. You have to complete debrand the phone in order to get these settings to stick and fix the mms lock out after many stupid attempts. GOOGLE IS YOUR FRIEND ON HOW TO DEBRAND!
Hope my first post helps out someone.
Click to expand...
Click to collapse
Sorry to bring up such an old post but is it possible to flash a US cellular mesmerize to boost mobile? I have recently flashed a nexus s 4g to boost and the mesmerize seems to have all the same specs...
Half Flash for Talk and Text only? (MMS maybe?)
vengeance937 said:
Flashing Samsung Fascinate To Cricket!!!!
ok so this is the one phone that has made me wanna punch my screen since i got it. amazing phone but hell an a half an very difficult to flash. OK so to start there are programs out there u can purchase to flash this phone if u wanna pay 100 dollars or 65 at a shop. but well im cheap so i set hours on end figuring what i could out. this tutorial will get u talk, text, 3g, internet an ability to send mms (to recieve has been difficult because there is a lock code to get to those features that ive been unable to find out)...
WHAT YOU WILL NEED!!!
QPST. 2.7 build 323 an build 215.
a Samsung fascinate.
PATIENCE!!
samsung fascinate drivers
and samsung epic drivers
first you will want to... (INGOING AN OUTGOING)
Click to expand...
Click to collapse
Hey there! Sorry to bring up an old post, but I have a question regarding this flashing business. I'm set up on Cricket's $35/month talk and text only plan and I had them flash my Fascinate to talk and text only since I don't want/use data (only wifi). I want to start messing around with the phone, but I'm afraid of losing the talk&text only flash. Should this happen will this guide allow me to flash to only talk and text with some modification? (I would LIKE MMS but there is supposedly no supporting plan for smartphones without data...)
Mr_Blam0 said:
Hey there! Sorry to bring up an old post, but I have a question regarding this flashing business. I'm set up on Cricket's $35/month talk and text only plan and I had them flash my Fascinate to talk and text only since I don't want/use data (only wifi). I want to start messing around with the phone, but I'm afraid of losing the talk&text only flash. Should this happen will this guide allow me to flash to only talk and text with some modification? (I would LIKE MMS but there is supposedly no supporting plan for smartphones without data...)
Click to expand...
Click to collapse
The $35 plan does not support MMS. Only the $45 dollar plan and the smartphone plans support it. Although if you set your account up with AutoBillPay you save $5/month. You will need the phone to be fully flashed in order to support it.
Source: I work for Cricket.

A "Pro" Flashing my Epic 4G to Metro

Bought an Epic 4G Touch and found a local guy on craigslist who's going to do a full flash to MetroPCS. I'm wondering if anybody has any suggestions as to what questions I should ask the guy. I'm new to this whole thing, this is my first smart phone, but I'm a quick learner.
From what I understand from my research, he's going to have to flash a custom rom on it in order for the phone's features to be fully operational. Is it important I find out which rom so I can perform my own updates, or is it going to be obvious what he did simply by looking in the settings?
Am I going to have to avoid OTA updates? Or do I just install Rootkeeper to get the updates?
I also assume that by doing this I will be stuck using the custom rom, right? Or as long as my ESN is added to the Metro system I can change it to any rom I can find that is fully operational with Metro?
Is there any other vital information I should make sure to ask for in case I need to configure anything in the future?
Would it be smarter for me to just ask him to add my ESN to metro and then flash it myself? (If I can find a guide online-- links, anybody?)
Feel free to add any information that you think might help!
Thanks in advance.
its pretty much about manually programming in your data settings 100% correctly. anyone can add an meid/esn into their database and program in your phone number(##SPC#). if you research online you can find the exact settings. i dont believe metro uses wap anymore so that certainly makes things easier.
you should be able to use ANY rom and be able to call/text/use data. the only issue you will run into(maybe.. i dont use metro) would be mms. mms sometimes is custom built for a specific phone/carrier. when you see metro/cricket custom roms.. thats generally the big modification.. the mms. you may get some little edits here and there.. changing the word sprint to metro etc... but otherwise thats pretty much it. as is.. the epic 4g touch can be manually programmed with any cdma carriers data profiles for 3g.
if you dont care about mms.. its a 100% no brainer.. take the time and do it yourself. if mms is a must.. do a little research to see if others on metro got mms working.. there will be people talking about it somewhere on the internet.
and just to add.. if u do use a custom rom for metro.. you will be stuck with that rom(unless its a freely available custom rom.. but those are rare these days.. most are sold on cdma forums for lots of $$$).
I will preface this with I've never done this before so I don't know the outcome. That said, at least in my area, the 4g is not compatible with lte, metro doesn't have 3g but 2g rttx1 should work. I don't know about you but if it were me, I wouldn't do it. That's like putting a restricting device on a Porsche so that its top speed is 30mph. 2g is practically dial up speeds. Do what you will though...
autoprime said:
its pretty much about manually programming in your data settings 100% correctly. anyone can add an meid/esn into their database and program in your phone number(##SPC#). if you research online you can find the exact settings. i dont believe metro uses wap anymore so that certainly makes things easier.
Click to expand...
Click to collapse
Thanks so much, great information. Question- Do you mean I can add my own ESN into the Metro Database myself? I thought only Metro reps could do that (independent ones for under the table).
As for the rest of the data settings, when searching for this information online, do I need to look specifically for Epic 4g Touch, or the data settings will be the same no matter what phone?
autoprime said:
if you dont care about mms.. its a 100% no brainer.. take the time and do it yourself. if mms is a must.. do a little research to see if others on metro got mms working.. there will be people talking about it somewhere on the internet.
Click to expand...
Click to collapse
Actually I don't care about mms, as long as I can do regular text messages (sms). Does this mean that if I don't care for MMS I can actually get the Epic Touch fully operational on the stock rom?
autoprime said:
and just to add.. if u do use a custom rom for metro.. you will be stuck with that rom(unless its a freely available custom rom.. but those are rare these days.. most are sold on cdma forums for lots of $$$).
Click to expand...
Click to collapse
So I couldn't re-flash it to a different rom? It's not "reversible"? (If it is possible- would I lose all the Metro data if I changed the rom?)
Thanks for the help, I've been Googling around like crazy trying to find more info, but not finding a lot. I probably should of gotten a more commonly metro flashed phone, lol. I'll keep looking around and see if I can find any guides, if I find one and can do everything myself I'd rather go that route (not to save money, just to be able to troubleshoot any issues that may arise in the future).
Edit: I've found this thread http://forum.xda-developers.com/showpost.php?p=8395950 that looks like it might be exactly what I need to do (up to step 28), and someone on this Epic Touch Forum recommended another member to this thread http://forum.xda-developers.com/showthread.php?t=1303507 but it's for Evo 3D, so not sure if it would work for the Epic. The guide starts off for phones already "flashed to metro with text and talk", though. I think I still need to pay the "Pro" to get my ESN added to the Metro Network? Are they able to add the ESN to the Metro Database and get text/talk working without flashing a custom rom?
Sorry... so many questions. I'll give lots of thanks =(
EDIT #2:
Think I got it now. Looks like I will need to get the phone Metro Flashed through my guy for talk and text (I can ask if his MMS/Web method involves a custom rom, if so I'll pass) then I can activate web (and MMS I guess) myself through these steps: http://forum.xda-developers.com/showthread.php?t=1303507
At this point (correct me if I'm wrong) I won't be locked into any custom roms and I can freely upgrade to any freely available rom (ie CM7) without affecting my Metro settings?
really not sure what the best procedure is for getting your esn added to the DB.. i would think any 3rd party metro store would be able to add it into system... as well as some people on craigslist. just look for the cheapest option.
once your esn ins in the system.. you pick a plan.. program in your phone number and msid (##SPC#) as well as write a metro PRL to the phone... and thats it for working talk/text. thats the "basic flash" most people do. only thing you cant do yourself is add meid.
and then you will eventually program data. the steps for evo 3d should be very similar to epic. other than how to get the phones into DIAG mode.. what to manually add is the same across the board... tho your username/password will be unique to you. (ppp password is based off esn.. username will be based on phonenumber).
i believe metro has recently added 3G in SOME areas.. so theres a small chance youll have that. and as for 4G... see my epic 4g touch thread on how to edit wimax settings...
ive said enough.. you should be able to take it from here.
edit: as for being "stuck" with a custom metro rom.. youd have the option to reflash anything youd like.. but the custom metro settings would probably no longer work. it would suck to pay for a custom rom that you end up wanted to switch out anyway(since it wouldnt be updated like he rest of the roms). i say pay the $10.. 15..20.. whatever it is to have esn added to the system.. then do the rest yourself.
If you search on ebay. There is a guy that can add your esn to metro for $25. Then you can flash your own custom rom, but you would have to setup your own data. If you search around, there are threads about how to setup data for metropcs around the web.
Ran outta thanks, I'll get you tomorrow
I looked it up on ebay and there's only a couple up atm and they end up being a lot, ie the cheapest is $20 but then they charge $25 shipping lol <.<
Luckily, the local guy I found on Craigslist (there are actually a lot independent metro stores in the area advertising actually) will add ESN and get talk & text working for $35. So it's not a bad deal. From there I'll get the rest working myself.
Although I'm gonna ask him about his MMS method, if it involves a custom rom I have been contemplating getting it. I been researching and it looks like all I have to do is backup the custom rom with nandroid, and I can flash to whatever rom I want, then I can always revert to the custom rom if I really want MMS working again-- if I'm unable to get it working myself.
My used Epic 4G Touch arrives in a few hours!
First thing I plan on doing is a full restore and then installing EL13+CWM. After this I'll get take it to the independent Metro store to get it flashed over to Metro. Then I'll make my first nandroid backup.
Question- By making the nandroid backup I can always revert back to the Metro data settings my guy configured, right? (In the case they get deleted through rom flashing).
Can I see all the settings he configured by reading the values set through CDMA Workshop? Would this include everything needed to make the phone fully functional on Metro again (outside of the possible custom rom to make MMS work)?
Thanks in advance.
Godswrath said:
My used Epic 4G Touch arrives in a few hours!
First thing I plan on doing is a full restore and then installing EL13+CWM. After this I'll get take it to the independent Metro store to get it flashed over to Metro. Then I'll make my first nandroid backup.
Question- By making the nandroid backup I can always revert back to the Metro data settings my guy configured, right? (In the case they get deleted through rom flashing).
Can I see all the settings he configured by reading the values set through CDMA Workshop? Would this include everything needed to make the phone fully functional on Metro again (outside of the possible custom rom to make MMS work)?
Thanks in advance.
Click to expand...
Click to collapse
nandroid wont restore data settings... but you wont need to as 3g data profiles(as well as talk/text) stick after new roms. only a ##786# full reset will wipe those settings.
you should be able to see most if not all settings with cdma ws/qpst service programming.
1. Phone number/msid has to be programmed.
2. Metro PRL Flashed
3. after step two you now have talk/text.
4. Program in 3G Profile 0/1.
5. Program PPP data profile.
6. Done. Only thing I skipped is MMS.. which will most likely be covered by a custom metro rom.. tho maybe you could take the mms ap out of the custom rom to use... but im just guessing at this point.
autoprime said:
really not sure what the best procedure is for getting your esn added to the DB.. i would think any 3rd party metro store would be able to add it into system... as well as some people on craigslist. just look for the cheapest option.
once your esn ins in the system.. you pick a plan.. program in your phone number and msid (##SPC#) as well as write a metro PRL to the phone... and thats it for working talk/text. thats the "basic flash" most people do. only thing you cant do yourself is add meid.
and then you will eventually program data. the steps for evo 3d should be very similar to epic. other than how to get the phones into DIAG mode.. what to manually add is the same across the board... tho your username/password will be unique to you. (ppp password is based off esn.. username will be based on phonenumber).
i believe metro has recently added 3G in SOME areas.. so theres a small chance youll have that. and as for 4G... see my epic 4g touch thread on how to edit wimax settings...
ive said enough.. you should be able to take it from here.
edit: as for being "stuck" with a custom metro rom.. youd have the option to reflash anything youd like.. but the custom metro settings would probably no longer work. it would suck to pay for a custom rom that you end up wanted to switch out anyway(since it wouldnt be updated like he rest of the roms). i say pay the $10.. 15..20.. whatever it is to have esn added to the system.. then do the rest yourself.
Click to expand...
Click to collapse
You can change your meid. ##YOURMSL#
Sent from my SPH-D710 using xda premium
locoboi187 said:
You can change your meid. ##YOURMSL#
Sent from my SPH-D710 using xda premium
Click to expand...
Click to collapse
yes it is possible to change an meid... but i'm not sure why ##MSL# is mentioned... the two are not related.
Hmmm... I'm stuck on this step :
USB Storage Mode is OFF - [Drag down the notification bar and tap on "USB Connected" - should be off by default]
When I click on USB Connected it just sends me back to Home. Any ideas?
(Step 1 from http://forum.xda-developers.com/showthread.php?t=1342728)
EDIT: figured it out, had to re-install drivers and change the default location to 32-bit
Nope, still no go... Hmm Maybe I'll uninstall drivers and reinstall them. Problem is my PC isn't recognizing phone as a drive, just a device.
Yeah I dunno, gonna give up installing EL13+CWM for now and go get it flashed.
I think the problem is, when I connect the device I get "Samsung Mobile MTP Device Failed"
I downloaded the Samsung USB/Android drivers [USB/Android] and have Kies installed (Kies can't even recognize it though).
autoprime said:
yes it is possible to change an meid... but i'm not sure why ##MSL# is mentioned... the two are not related.
Click to expand...
Click to collapse
Your MSL code entered at the dialer with the "#" brings up a menu in which you can edit. I used this with a sprint tech when trying to fix my gps
Sent from my SPH-D710 using xda premium
Godswrath said:
Hmmm... I'm stuck on this step :
USB Storage Mode is OFF - [Drag down the notification bar and tap on "USB Connected" - should be off by default]
When I click on USB Connected it just sends me back to Home. Any ideas?
(Step 1 from http://forum.xda-developers.com/showthread.php?t=1342728)
EDIT: figured it out, had to re-install drivers and change the default location to 32-bit
Nope, still no go... Hmm Maybe I'll uninstall drivers and reinstall them. Problem is my PC isn't recognizing phone as a drive, just a device.
Yeah I dunno, gonna give up installing EL13+CWM for now and go get it flashed.
I think the problem is, when I connect the device I get "Samsung Mobile MTP Device Failed"
I downloaded the Samsung USB/Android drivers [USB/Android] and have Kies installed (Kies can't even recognize it though).
Click to expand...
Click to collapse
Maybe you need USB debugging enabled by going to Settings > Applications > Development
Sent from my SPH-D710 using xda premium
Thanks, but no go. Have debugging checked. (I followed the tutorials to the letter)
youre trying to root?
I successfully rooted with the full restore, what I tried to do next was install EL13+CWM and I noticed 2 things:
1st) I can't get past this step: USB Storage Mode is OFF - [Drag down the notification bar and tap on "USB Connected" - should be off by default - pic] (ie when I tap on "USB Connected" it just takes me back to the home screen.
2nd) I continued with the tutorial since it says it should be set correctly as default, but then when the E4GT automated rooting package (not to root, but to install EL13+CWM) it hangs saying "Waiting for device to be connected"
When looking for an answer I discovered this:Why is the install stuck waiting for device to be connected? which gave me some ideas to try, although I've tried all of them to no avail.
I should note that when I go to start->run->devmgmt.msc this:
Code:
Android Phone
SAMSUNG Android ADB Interface
Modem
SAMSUNG Mobile USB Modem
isn't listed there, like it says it should here.
I think I'm going to try to reinstall all the drivers again... Should I do this before or after connected the phone? (The first time I installed the USB/Android drivers from the tutorial before connecting my phone, but I notice after connecting the phone windows goes through the automated process of installing drivers)
<face palm>
http://androidadvices.com/enable-usb-storage-android-devices/
It was so simple, lol... To my own defense this wasn't anywhere in the tutorials
Thanks again for the help guys
EDIT: Well, looks like my problem is still here, the E4GT automated rooting package still hangs searching for device to be connected.
EDIT #2: Omg... Finally figured it out. I thought debugging was enabled (it shows a freakin' check mark) but it has to be a green check mark apparently...
Weee installed CWM, now to create a nandroid and start flashing! Think I'm going for Calkulin's rom with the ICS Theme
Another question!
Hey guys, question:
I got 2 E4GT's flashed over to MetroPCS, both are working fine, but one of them gives me this error on bootup:
Code:
Error 67: Registration failure. Your Sprint data service username
and/or password may be incorrect. Please try again.
Any ideas? Aside from the nuisance, it hasn't seemed to cause any hindrance to the features. The other phone has never given this error, though. Both are running on Calk's rom. Thx guys.
Godswrath said:
Hey guys, question:
I got 2 E4GT's flashed over to MetroPCS, both are working fine, but one of them gives me this error on bootup:
Code:
Error 67: Registration failure. Your Sprint data service username
and/or password may be incorrect. Please try again.
Any ideas? Aside from the nuisance, it hasn't seemed to cause any hindrance to the features. The other phone has never given this error, though. Both are running on Calk's rom. Thx guys.
Click to expand...
Click to collapse
if its only at bootup i wouldnt worry too much. its just the firmware trying to get a sprint connection and it failing.. since youre connected to metro. i would check ##data# > view > data profile/username.. compare whats listed for the one thats working to the one thats giving the error. are they both the same? if not, make them the same and perhaps you can avoid the error. if they are the same... its probably some little data setting somewhere that the phone doesnt like and likely not worth the hassle of poking at it more. like i first said.. the error at boot really isnt a huge deal. if it was a constant error that kept popping up then its something to look at.

[Q] Need help getting an EVO on MetroPCS...

Hi all,
Thanks for a least looking at this thread and providing feedback. So here is my situation.
1. Bought EVO 4g from a friend who bought new phone and transferred his phone number from Sprint to Verizon so the phone does not have access to Sprint's network.
2. My wife has a crappy MetroPCS phone I would like to replace with the EVO 4g.
3. I have all the software that has been talked about in many threads here: diagnosis drivers, cdma workshop, prl, and a few other things which I can't remember.
4. I have rooted the phone with S-OFF and currently running MetrogenMod 4.5
Q1: Does the phone need to be on the Sprint network in order for me to get the phone working on MetroPCS?
Q2: After reading all of the forums it sounds like the phone will magically work on MetroPCS' network, but something tells me I'm missing something?
Q3: How do I get my wife's phone number transferred over to this phone? It seems I can only transfer the current phone number that the phone has even though it is not mine.
Thanks again in advance and I apologize if these questions have been asked before, but I did not see any.
Jamdev12
PS: Ok after reading and getting familiar with this stuff it seems there are two ways of doing this, but I rather get some expertise from someone first :
1. Easiest method. Call MetroPCS and request an ESN swap. Since I own both phones I don't foresee this as illegal and I've heard of people successfully getting this done.
2. Hardest method and possibly bricking the phone. Call Sprint and request MLS number. Then use the software that is available to get ESN from old phone and write it to the new phone. If done right, the new phone will act and connect as if it were the old phone.
To all, am I correct in the above assumptions?
You shouldn't need to call sprint for your msl..search the play store for "msl reader". It'll save you that hassle anyways. ....Did a quick search and found this guide over on af.. http://androidforums.com/evo-4g-all-things-root/538899-guide-metro-pcs-donor-flash.html .. I flashed to boost so thats the extent of my experience. Hope it helps.
Hi nrvlljr,
Thanks for this link. I will be trying this tonight and if I get it working, I'll post my findings. Wish me luck. :good:
jamdev12
jamdev12 said:
Hi nrvlljr,
Thanks for this link. I will be trying this tonight and if I get it working, I'll post my findings. Wish me luck. :good:
jamdev12
Click to expand...
Click to collapse
Break a leg buddy..Just make sure to follow the instructions to a tee and you'll be fine.
nrvlljr said:
Break a leg buddy..Just make sure to follow the instructions to a tee and you'll be fine.
Click to expand...
Click to collapse
Hi nrvlljr,
Thanks for the encouragement. Unfortunately it did not work for me. For some reason the phone is unable to log into the MetroPCS network as my old phone. One thing that confused me about the instructions was to save the nam1 and Nam2 data for my old phone because not once after that did I use this data to reprogram the new phone. All it says is to replace the ESN and meid numbers in the nvm folder and reboot.
Next I tried the MetroPCS tutorial in the developer forum to get MetroPCS working, ROM and everything without success. I'm able to connect via roaming, but not on my current phone number.
Anyways, if you or anyone here has any ideas, I would gladly appreciate it. At least the phone is not bricked, yet.
Thanks in advance.
jamdev12 said:
Hi nrvlljr,
Thanks for the encouragement. Unfortunately it did not work for me. For some reason the phone is unable to log into the MetroPCS network as my old phone. One thing that confused me about the instructions was to save the nam1 and Nam2 data for my old phone because not once after that did I use this data to reprogram the new phone. All it says is to replace the ESN and meid numbers in the nvm folder and reboot.
Next I tried the MetroPCS tutorial in the developer forum to get MetroPCS working, ROM and everything without success. I'm able to connect via roaming, but not on my current phone number.
Anyways, if you or anyone here has any ideas, I would gladly appreciate it. At least the phone is not bricked, yet.
Thanks in advance.
Click to expand...
Click to collapse
Ok, so after more fiddling, I was able to get Data working, but no talk and text. To get data working, I had to run DFS to import the latest PRL from MetroPCS into the phone. Once I did that and rebooted the phone, 3G started to work, but still could not get Talk and Text to work.
Then I did the worst thing that I could have done, I think. I order for me to get Talk and Text working, I took the phone to a MetroPCS. Well, I let them run the phone through Houdini and now Talk and Text work, but I can't get 3G to work even though I have a plan that has Talk, Text and Data and I have reloaded the MetroPCS PRL in the phone.
Has anyone ran into this problem? Would I have to get my phone off the MetroPCS database in order for me to get 3G running again? Any help would be gladly appreciated.
Hello, I, new here..
I have literally tried everything i have read from forum to forum, post to post, from installing DIAG drivers to QPST, apn, anycut, everything i have found and cannot make my EVO to connect to the web. My sister had this phone fully working (except 4G) and now that i transferred it to my account i make calls and text but not MMS or WEB. less 3G. I am very frustrated but willing to keep on reading instructions if anyone would be able to help!!. Thank you very much and you guys are doing a very great job. miraculously i am obtaining knowledge i never even though it existed! unfortunately havent being able to solve my problem.
jamdev12 said:
Ok, so after more fiddling, I was able to get Data working, but no talk and text. To get data working, I had to run DFS to import the latest PRL from MetroPCS into the phone. Once I did that and rebooted the phone, 3G started to work, but still could not get Talk and Text to work.
Then I did the worst thing that I could have done, I think. I order for me to get Talk and Text working, I took the phone to a MetroPCS. Well, I let them run the phone through Houdini and now Talk and Text work, but I can't get 3G to work even though I have a plan that has Talk, Text and Data and I have reloaded the MetroPCS PRL in the phone.
Has anyone ran into this problem? Would I have to get my phone off the MetroPCS database in order for me to get 3G running again? Any help would be gladly appreciated.
Click to expand...
Click to collapse
What kind of phone did you use for the donor flash? I had this problem with my old evo 4g. I had it donor flashed from a freeform 1. Even though I was paying for 3g the evo didnt get it. I assumed it was because my freeform didnt have 3g so the ESN being read by the network on my evo didnt require it to send 3g data. Just a guess

Categories

Resources