Develop Bugs

Hello Guys I need Your Help

First of all Hello
I've been trying to update my XDA2i Pocke PC for more than an hour
and every time I start the Update Operation I got an error message and the operation corrupt agian it prompts me to reset it, after the reset, it informs me to disconnect the Pocket and Cardle USB, and reconnect it Again but it gave me a message on its screen told me Serial on the top of the screen, and on the buttom V1.01< What should I do?
Please Help me to get it alive again because it's dead now, and it won't work anymore, I need the method of booting it up, what are the buttons combinations to enter the boot again.
and If you gave the ROM Update for it, I'd be so grateful!! :lol:
PS: the Pocket information are
Pocket PC O2 XDA2i

Are you using a usb hub to connect, if you are then try plugging in direct to usb port. You will not be able to boot until you complete the flashing procedure, the program has probably wiped your previous rom.

It didn't work
Thanks sir,
but how can I do the flashing procedure, the Pocket PC wouldn't give the chance to do it!
and I've already plugged the USB directly to the PC.
Could you give the manner to falsh it again and boot,
because it is dead and silent
I'll be so grateful for your efforts

Not even stuck at Bootloader :(

Please help!
I just upgraded my ROM to Ivan's latest AKU3.5 from bootloader
This completed successfully (100% successful, disconnect and restart etc)
I disconnected and reset, except it was stuck in bootloader mode
I tried the Mtty method (for the first time ever) and followed the step by step instructions...
...after a few seconds a few command lines appeared with "USB>" on the last line
I took this to mean the process had finished (?), disconnected the device from USB and tried a soft reset
the device just stayed stuck in bootloader
next, i downloaded uni_exitbootloader and ran it (as this has worked for me many times in the past). it didn't work the first few times, but i disconnected and reconnected and this time it worked. It said "data sent, you can now reset your device"
This maybe where i went wrong?
I foolishly reset the device before disconnecting it from the USB. The PC immediately said "USB device not recognised" and the screen of my Universal went blank
Now, if i soft reset, it does nothing, i cannot even put it back into bootloader using the camera, on, reset button combination.
HOWEVER, if i press the two soft keys (as if i was going to do a hard reset) i get the white screen with the black text saying "Press 0 to restore etc"
If i press 0, it says "clearing" but the screen just goes blank
If i press x, the screen just goes blank
Now i am completely unable to try and use either mtty or exitbootloader as my PC just says "USB device not recognised" and neither applications run as they should
QUESTION: Have i totally bricked my Universal?!
If not, what can i possibly do...???
As usual, i will be extremely greatful for any advice or assistance to resurrect my favourite Pocket PC!
Thanks in advance for your help.

Aaagh! I think i just realised what i did...
1. I didn't read the posting "For all those stuck in the bootscreen, try the Mamaich method" carefully enough. I didn't realise that the Mamaich method totally erased the ROM!!!
2. By not flashing a new ROM to the device immediately and instead using exitbootloader to exit the bootloader screen i now have a device that has no ROM and probably has no way of knowing how to get into bootloader mode.
Can someone confirm this?
For one, i feel like an idiot for not reading the posting carefully, but having admitted to being stupid,...
... is there anything at all i can do???
Please help...

cancel that, you already said what i was going to ask above

have you try to flash it again with original ROM? sometimes it helps!

Once in bootloader mode, try plugging it into a different USB port, one directly on the PC.
I have had this where one port says not recognised, even after having been plugged in and used for ages, then I go to flash it and it won't work.
Another port has worked for me.

Since you ereased the DOC, all you've got to do now is to reflash the default ROM.

Thanks everyone...
Only problem is, i cannot get it into bootloader mode. And every port i plug it into (so far) says "device not recognised"...
Nevertheless, i did try to reflash the device, but it just gave me the "Error 150" message. It just doesn't know the device is connected i guess?
I think if i hadn't done the Exitbootloader step then i would have been able to reflash it. However, now that i have... i'm a bit stuck... any ideas of other ways to get the device into Bootloader mode?

try
you already know there is a file called EXITBOOTLOADER but did you know that here is a file called ENTERBL ?
try it .....

Thanks dhob187!
Where might i find this file though? Did you mean to attach it?
Just one other question...
How does ENTERBL work if the PC doesn't recognise my device i.e. "USB device not recognised"? Will the application override this and push commands to my pocket pc anyway?
Or is there a way i can get my PC to stop rejecting the device when i plug the USB in?
Thanks in advance,

I believe this is the file u needed
i don't know how this utility works, but just yesterday i stuck in the bootloader after upgrading my uni to AKU 3,5 and solved with ExitBootloader.exe. CMIIW it works the same way, just plug the USB cable then execute the utility (just simple as that).....
but have u tried my earlier suggestion? my friend got the exact problem like you (blank LCD not even bootloader), he was downloaded the original EXEC ROM and try to flash with it (with original upgrade utility also). and the thing start to blink, enter the bootloader and flashing!.....after he manage to wake the device up, then he tried to flash it again with the newest ROM and succeded........
sorry for my english.....

Please don't apologise for your English, thank you for your suggestions!
I didn't quite understand your initial post... but i do now.
Does it have to be the first ROM that it was shipped with or just an original i-mate JasJar ROM?
I can't try it now, but i'm excited to go home and give it a go later tonight... what's more i'm excited at the prospect that there may be some hope for my currently rather expensive paperweight!!!
If the aforementioned doesn't work, i'll try using your attachment.
Cheers again!

it doesn't have to be the first rom that shipped with your imate, just an original one. try your luck then! never give up, keep the faith!!!

sorry, forgot one thing, just ignore the USB error (not recognized) and go for the upgrade (execute the original upgradeUt.exe)

Hi Rudy173.
Thanks for your help, but unfortunately nothing has worked
I have tried running two official JasJar Roms without success... i always get the connection error message (this is surely because the PC always says "device not recognised" when i plug it in).
Also, when i run ENTERBL.exe i just get a failure saying that ...ENTERBL.exe is not a valid WIN32 application... etc...
So unfortunately, i'm still stuck... any further suggestions anyone?
Can the i-mate service centre help me? Is it likely to be expensive?

Back in business )
Wow, not entirely sure what i did... but my Universal is ALIVE!!!
As per the previous post, nothing seemed to be working so i removed Activesync 4.5 beta and reverted to 4.1. I then tried to reflash to an original ROM and the same "connection error" problem happened.
However, next time i tried to enter bootloader, by pressing light, on/off and reset, it went straight into bootloader and i was able to reflash from there
I didn't even need to reflash with an original i-mate ROM. I went straight for Ivan's latest.
This experience has taught me a few things:
1. I have become seriously attached to my Universal!
2. You should never give up hope of retrieval!!
3. This forum is full of very nice helpful people!!!
Thanks everyone.

wow! glad to hear that!
Happy ending....................

HELP!! Diamond Stuck in bootlaoder

Help pls i have olinex 1.40 hardspl in but my phone is stuck in bootloader with "upgrade ROM code error Please try again" i cant get out...tried hard reset nothing...tried recovery mode (volume down + reset ) nothing...cant get a usb connection help!!!!!!!!!!!!!!!!

are you sure you don't have usb connection? try running an ruu with usb plugged in see if it runs. it sounds like you tried to flash a radio from another device. try flashing a new radio.

Blazeitup123 said:
are you sure you don't have usb connection? try running an ruu with usb plugged in see if it runs. it sounds like you tried to flash a radio from another device. try flashing a new radio.
Click to expand...
Click to collapse
the bootloader shows usb when i plug it in and serial when i plug it out...when hard resetting it goes through the formatting but then just jumps back to bootloader with the message...active sync recognizes nothing but i'll try that right now
edit - ok it seems to be flashing i'm crossing my fingers
edit: ok it seems to have flashed i see my rogers main screen thank you soooooooooooooooo much

glad to hear!
just so you know you can always flash from bootloader. i have seen alot of people around here saying "oh no, my device is bricked and i'm stuck in bootloader". i lol.

Blazeitup123 said:
glad to hear!
just so you know you can always flash from bootloader. i have seen alot of people around here saying "oh no, my device is bricked and i'm stuck in bootloader". i lol.
Click to expand...
Click to collapse
lmao now i know..i was coming from an elfin, not used to diamond as of yet but now i know

Bootloader bottom says "serial" but wont switch to "usb"
Perhaps this is a known issue but I could not find the solution easily and ended up discovering it myself so wanted to share it in case others face the same.
I was try to use the mtty software to "clean" my touch diamond in an effort to get rid of some bugs in macadam 1.2 rom [great rom, by the way].
I had disabled the usb connections in active sync on my laptop [mac running windows xp in bootcamp]
I could enter bootloader easily but the bottom part of the multicolor screen kept saying "serial" and would not switch to "usb" when I connected the phone to the laptop.
What finally worked was ensuring that the phone was set for "activesync" rather than use as a "disk drive" or "internet sharing". I had assumed, wrongly, that once in bootloader the last selected option [disk drive] would be irrelevant.
So I exited the bootloader by pressing the reset key; connected phone to pc via cable; selected the active sync option; disconnected the phone; entered bootloader, connected the phone via cable again and the bottom of the bootloader changed to usb and I was able to use mtty successfully.
I wonder if this has implications for people stuck with bad flashes etc. In my case I could easily exit the bootloader and go back and select 'activesync' from the working phone. One could also hard reset if a working rom was on the phone...
BUT If one is stuck with the option of only the bootloader, would it matter on what the last selected option was [active sync or use as usb disk drive or internet sharing]?

faisal said:
Perhaps this is a known issue but I could not find the solution easily and ended up discovering it myself so wanted to share it in case others face the same.
I was try to use the mtty software to "clean" my touch diamond in an effort to get rid of some bugs in macadam 1.2 rom [great rom, by the way].
I had disabled the usb connections in active sync on my laptop [mac running windows xp in bootcamp]
I could enter bootloader easily but the bottom part of the multicolor screen kept saying "serial" and would not switch to "usb" when I connected the phone to the laptop.
What finally worked was ensuring that the phone was set for "activesync" rather than use as a "disk drive" or "internet sharing". I had assumed, wrongly, that once in bootloader the last selected option [disk drive] would be irrelevant.
So I exited the bootloader by pressing the reset key; connected phone to pc via cable; selected the active sync option; disconnected the phone; entered bootloader, connected the phone via cable again and the bottom of the bootloader changed to usb and I was able to use mtty successfully.
I wonder if this has implications for people stuck with bad flashes etc. In my case I could easily exit the bootloader and go back and select 'activesync' from the working phone. One could also hard reset if a working rom was on the phone...
BUT If one is stuck with the option of only the bootloader, would it matter on what the last selected option was [active sync or use as usb disk drive or internet sharing]?
Click to expand...
Click to collapse
This doesn't make any difference. When you're stuck in bootloader just plugin your USB and the display will state "USB" as well. You can flash a rom at this point.

Need help..My BA stuck in 'USB' / 'Serial' gray screen

heloo
I am currently upgrading my XDAIIs from WM2003 to WM6.5.
after checking the system from my XDAIIs, suddenly the power led went off and the sync is disconnected so I cannot continue the upgrade. On my phone screen there are only gray screen with USB at the top and V.2.07 at the bottom.
I have tried to restart the upgrading process but the problem is now my phone cannot connected to my laptop although I am using USB. I also tried to change the usb port and sync with other computer, but the problem is still the same.
FYI : at the beginning of the upgrade process, I didn't hard reset the phone. Is this the cause of the problem??
Please help me, does anyone have any solutions?

your device is in bootloader mode and it should show up as a ms_wm_device in
windows and you should be able to flash it again you can read more here
http://wiki.xda-developers.com/index.php?pagename=HTC_Blueangel

chanxda... you sorted it yet! I had same problem last nite and figured it out. Ill watch thread if you need reply!

no active sync connex after flashing rom

reflash.. impossible
--------------------------------------------------------------------------------
hi guys, ive a strange problem.. after flashing mad's ita-rom in my hermes, as i retryed to flash another one it was not more possible.
in the beginning normal connex but before going in bl-mode...error and nada
active sync 4.5 AND 6.1 refused to reconnect to device.
i tryed to put manual in bootloader modus.. nothing happened.
well, i ve the sd card modus possibility but i want use this as last solution.
please need info, thx

what do you mean by "i tryed to put manual in bootloader modus.. nothing happened. "?
Did it enter bootloader? If so, don't look at ActiveSync, it won't show you anything, just run ruuwrapper and flash your baby

hmm?
yes, it enter in bootloader modus, but if i try to run wrapper, same error than without..
active sync stay connected until arriving to verify the device.. after that.. error coz cable unplugged or not correct connected..

HTC_BALI said:
yes, it enter in bootloader modus, but if i try to run wrapper, same error than without..
active sync stay connected until arriving to verify the device.. after that.. error coz cable unplugged or not correct connected..
Click to expand...
Click to collapse
The same error happened to me quite often.
use the SD card method, its way better.
rename the .nbh file to hermimg.nbh and put it on a smaller than 2 Gb SD card formated to Fat32, then enter bootloader (power, ok, reset) and wait till the device asks you to press power button to start upgrading.

i try
oki, i will try it and let you know.. btw... jade is FANTASTIC...
never a problem after flashing with olinex hard spl..
thanks for the help..

i bring him in bootloader, but stucks there.. what now?