Screen fades in to white - 8525, TyTN, MDA Vario II, JasJam ROM Development

My screen fade in to white any ide what that happens or what i can do to orevent it from fading like that. or is it broken beyond repair

Hi, here's an active thread on the whitescreen to check for possible solutions:
http://forum.xda-developers.com/showthread.php?t=321163

tnx alot, I wasent sure there was a solution to my problem.

Another White Screener
I to have now joined the white screen brigade! phone was working fine and suddenly started doing it. I have tried several WM6 roms since, and the same problem eventuates. I notice on first booting, that some of the details are at the top of the screen as well as the bottom (M.S.B etc instead of all at the bottom) Even the windows green screen has a thin band of bright green at the top which clearly belongs at the bottom, like some other complainants, I also find some of the fast key buttons (internet and mail) do not work. I took it to the service centre who will not do anything with it while it has WM6 in it (Jasjam have not realease that here). They want to revert it to WM5 (at my cost) and then try and repair, with no guarantee. Some deal huh. Any ideas, surely it cant just be the rom if the problem continues with additional roms, and can it really be just flex if the buttons stop working?

Slow computers!!
Damn...after all that typing I just found Alkizmos reply....thanks...I will go back to the repair shop i think!!

Related

White screen, cable problems, unusable BA... Please help!! Thank you!

Hi all! I hope I'm not disturbing here, but I'm quite desperate with regards to my poor BA... After replacing the display about a year ago (the touch-sensitive layer had broken) everything was going well, but something bad has been happening for some months now, and I think it has come to the point of no-return...
At first, when I slid the BA open, there would be a point in which a change in the colors on the display happened, as if the the Red and Blue channels worked well while the Green one was dim (as noticeable during the boot process). Then, opening it completely, it came back to the normal state. The situation worsened, sort of "interference" could be seen while opening the BA, the touchscreen would lose calibration after some openings and closings and so on...
Now the worst: when I turn it on, the screen is completely blank and white; sliding it back and forth would once get it to work, but now it is completely useless. About halfway between the open and closed positions the backlight itself turns off and then on again. It is impossible to see anything and it is unusable!! I opened the BA and made sure everything was connected, I re-connected the LCD and the touchscreen cable but nothing changed... I don't know what to do...
Does anyone have any suggestions? Can I try to repair it or to have it repaired, or, as it is a bit visibly used, should I resign myself to saying it goodbye?? Thanks for your patience and help...
News!! I rried to replace the new screen with the old (broken touchscreen) one, and that one works. Save for a problem, the green colour is lightly dim in the exact positions in which the backlight goes off with the "new" but not working display... Does anyone have an explanation for this behaviour? Thanx again!!

[Q] TocuhFlo3D problem!

Hi! I have a big problem with my Rhodium.
I have post another similar thread before but aybody seems to respoding..
I don't know what happened to my phone.
The touchflo3D seems to not responding. in other words the screen reacts when I tap on it, but I can't move or select anything on the screen.
I don't understand if it's a software or hardware problem.
The problem born with a custom rom I installed.
R [WWE|GER|FRA|ITA|NLD] |Feb 12| Energy™-.¸¸.·´¯ 6.5|21916 / 6.5.X|28244 * Sense 2021
after few days of no problem, the screen became as I described, incapable to select anything.
I tried also to move to the settings to disactivate sense but it was impossible with only the keyboard.
I searched on the forum for the solution, but the methods proposed didn't resolve the problem!
So I decided to return to the ufficial Rom.
RUU_Rhodium_HTC_ITA_1.19.408.1_Radio_Rhodium_3.44. 25.27_Signed_Ship
I performed a HardReset before the reinstall of the ufficial rom, but the problem remained.
So I performed a task29, but after the reinstall nothing changed and the TouchFlo seem to be broken.
I followed the guides proposed but I don't think I commited something wrong...
I suppose is a problem of the software because, I repeat, the screen react to my tap when is in minimum light.
Please help me because I don't know whato to do...
Tnx to All!!!!
Is the issue *only* with Touchflo? Can you tap on the Start menu and bring it up?
I'm confused as to why you say "the screen reacts when I tap on it, but I can't move or select anything on the screen"
How can you tell if the screen reacts?
Mnementh666 said:
Is the issue *only* with Touchflo? Can you tap on the Start menu and bring it up?
I'm confused as to why you say "the screen reacts when I tap on it, but I can't move or select anything on the screen"
How can you tell if the screen reacts?
Click to expand...
Click to collapse
Hi! No I can't tap on the start menù and when I tap on any icon on the screen nothing happens!
What I meant with "the screen seems to react" is that (sorry for my English XD!) before the screen goes black, the light goes high to low, ok?
when the screen has low light, and I tap on the screen, the light goes to high, so it seems that the screen can react to my tap.
tnk you very much for your response.
If I wasn't capable to explain correctly, please tell me 'cause I'm a little worried for my phone!
Bye.
i don't want to bring down any hope left, but if it does not respond to anything you do, i think your phone has just lost its flat cable. It might be broken and fixing it up would be a total pain. I would bring it back to where you bought it. Contact me through pm for further details, if u're still wondering what does this mean.
G4rreT84 said:
Hi! No I can't tap on the start menù and when I tap on any icon on the screen nothing happens!
What I meant with "the screen seems to react" is that (sorry for my English XD!) before the screen goes black, the light goes high to low, ok?
when the screen has low light, and I tap on the screen, the light goes to high, so it seems that the screen can react to my tap.
tnk you very much for your response.
If I wasn't capable to explain correctly, please tell me 'cause I'm a little worried for my phone!
Bye.
Click to expand...
Click to collapse
This sounds either like a broken / damaged ribbon cable (the "flat cable" the previous poster was referring to) or a damaged / broken digitizer.
On my old phone, the digitizer slowly broke - first the accuracy of the touchscreen would slide, then it got to the point where it wouldn't register 'on screen' at all, even though the phone could still tell I was tapping the screen because the backlight would come on etc, just as you describe.
Replacing the digitizer will cost money, but if you're going to do that find someone good at doing it! And also consider getting the device checked out and replacing the ribbon cable too, it's probably one of the most vulnerable parts of the device so it can never hurt to be overly cautious and replace both of them. Unfortunately there's always a cost involved
Let us know how you get on...
Hi the cable is not the only thing that can couse your screen to not respond, ive seen a tp2 that stoped responding because IT captured humidity in the digitizer screen, you can tell if this is the case by mooving your phone under the sun light and you will notice a kind of rainbow loking transparente spot, this humidity causes the digitizer screen to get stuck, the Solution can be to let it dry in the sun, or to rub it jently against your leg, the fricción can help to dry out the humidity, hope IT helps.
Search on here "tp2 screen not responding"
There is a thread on here I found about the screen not responding, and cleaning around the chrome edge with something thin, carefully, (I used my fingernail, which worked, but I lifted the contact too much down by the buttons on the bottom of screen). Worked for me and a few others. Good luck.

Display Graphic problem

I've got a problem with a OneX I'm trialling for work.
This is a stock device with the latest OTA update applied. I installed Good for Enterprise, activated it, and got my work emails. I opened a PDF attachment which opened for a couple of seconds then the display glitched.
The attached images show what I mean. The display is glitched for every screen. Soft resetting the phone was okay until it started again a couple of minutes later.
Soft resetting a 2nd time was where my real problems started. The phone vibrated as it started, but the display stayed dark. If I tap the power, the touch buttons light up. If I go through the motions of the lock ring and my gesture lock, I feel vibrations of my actions but can't see a thing. If I ring the phone, it rings, the touch buttons light up and the LED blinks. The display stays dark at all times.
Does anyone have any idea what's going on here? It's almost like when a graphic card overheats in a PC.
I would try a hard reset, see what that does, it should fix it as it looks like software problem
Squeeze your phone between thumb and forefinger (on the screen and rear cover) about 1.5-2cm in from the USB port, and slightly below. Let us know if the screen comes back on.
ZenithUK said:
I've got a problem with a OneX I'm trialling for work.
Click to expand...
Click to collapse
I think your phone is on drugs.
Seriously though, that's the scariest gfx bug I've seen on a phone.
Work were just as surprised as everyone else.
It's been sent back to them so they can talk with Vodafone about just what's happened with it.
In the few days I had it, it's a decent phone. The primary reason for considering the OneX is the screen size, and the fact you can read a PDF clearly on it.
ZenithUK said:
I've got a problem with a OneX I'm trialling for work.
This is a stock device with the latest OTA update applied. I installed Good for Enterprise, activated it, and got my work emails. I opened a PDF attachment which opened for a couple of seconds then the display glitched.
The attached images show what I mean. The display is glitched for every screen. Soft resetting the phone was okay until it started again a couple of minutes later.
Soft resetting a 2nd time was where my real problems started. The phone vibrated as it started, but the display stayed dark. If I tap the power, the touch buttons light up. If I go through the motions of the lock ring and my gesture lock, I feel vibrations of my actions but can't see a thing. If I ring the phone, it rings, the touch buttons light up and the LED blinks. The display stays dark at all times.
Does anyone have any idea what's going on here? It's almost like when a graphic card overheats in a PC.
Click to expand...
Click to collapse
Mine looks exactly the same once Ive had a few whisky's...
I had the exact same problem, so I shipped off my phone to service.
They actually changed the whole motherboard. I got my phone back 2 days ago, and it is working better than ever. Even better than before they changed the board.
My guess; Same problem as me. Busted motherboard. Im waiting to get a reply from the service guys that fixed my phone, so I can get some solid answers about what was actually wrong.
Hope this helps!
Best regards,
Sebastian

OneX EU Version vertical dark line on the middle of screen

OneX EU Version vertical dark line on the middle of screen.
For me, I think it is related to LCD signal quality, maybe panel problem or screen cable problem. Anyway, it should be a HW problem.
The dark line is about 1 or 2 lines. It is okay with white screen, but has problem with light blue, yellow, green and light red pictures. It is not a constant problem. I can get the line removed by changing color with flashlight app. Sometimes, the dark is disappeared when you change screen colors in the app. Then it will come again at sometime.
Reboot, no help.
Anyone encountered such problem?
does sound like hardware, can you take a picture?
Attached pictures, you can see the line on blue screen and yellow screen. But nothing with white screen.
you could try safe mode (i think you have to hold volume down when restarting the device, until you feel it vibrate a few times), and then a factory reset if safe mode doesn't help, if it still persists, i'd go for replacement/repair
does look like hardware, although strange it doesn't show on white screen, but then again a dead pixel wouldn't show on a black screen, so can't rule out hardware
Many thanks for your advice. Since there is no such issue reported on the net, I just shared findings here. Maybe I will try factory reset later when I get backup ready.
lawrence750 said:
you could try safe mode (i think you have to hold volume down when restarting the device, until you feel it vibrate a few times), and then a factory reset if safe mode doesn't help, if it still persists, i'd go for replacement/repair
does look like hardware, although strange it doesn't show on white screen, but then again a dead pixel wouldn't show on a black screen, so can't rule out hardware
Click to expand...
Click to collapse
Have tried factory reset, no help.
I also can see this issue even on boot screen. So it is related to HW. But also I can make it fix sometimes with some screen fake out conditions. (by "color flashlight" tool).
Hi
jiazhen said:
Have tried factory reset, no help.
I also can see this issue even on boot screen. So it is related to HW. But also I can make it fix sometimes with some screen fake out conditions. (by "color flashlight" tool).
Click to expand...
Click to collapse
It is faulty, simple as that unfortunately.
Regards
Phil

[Q] screen flickering

Hi guys,
anyone had an issue where the screen flickers really badly? Mine has been working great then today it did a weird glitch where the button bar at the bottom went halfway up the screen, and the screen flickered really bad, like a tube light starting up. Ive reset it and now its flickering like a fluorescent tube light. everything still works, but im on the phone to three now organising to get it returned.
cheers
Ray
ok, so an update to this. after leaving the phone on all day the flickering screen stopped flickering, however now i have an issue where plugging my ear pollution headphones causes the phone to now show as a headset with microphone, and the voice assistant to appear. It is also now getting really hot on charging where it didnt before, so my returns envelope arrived today, and its off back to LG for a repair. Seems very strange how its happened after a month of relatively light use, where my 2 htc phones were working great after 2 years of use?
anyway, lets see what rubbish comes back from LG
Home screen Magnifies
I have a weird problem with LG G3 screen
When i double tap to lock the screen .....Home screen Magnifies and if i double tap on that again it goes back to normal
I dont understand why .....can anyone please suggest me if any option to be tweaked under settings
Thanks
Vj Roshan

Categories

Resources