Related
I tried to upgrade my rom but the process crashed. The utility mtty doesn't work because when I connect the universal, boatloader mode by the cable, to the pc, it says "USB not recognized" (sometimes when I connect the computer is frozen till I disconnect the cable of the universal)
Please, I tried to have some solutions in the forum but all the posts indicates is needed previously the usb connection.
Do you know if should be possible to run the flash of the rom in other way, for example using a serial cable connected into the miniusb of the universal, because the boatloader screen says "Serie, v.1.01"
I apprecite what you can say please, I'm really in a hole.
Try this...
Try taking out the battery for a few minutes (10-30mins) and reboot your PC then repeat upgrade process. Hope that helps. Good luck!!!
I have the same problem on my PC at work, it's caused by a poor USB chipset in the PC, or trying to connect through a USB hub.
The only thing I found that worked was to try a different PC, then it was fine...
sl9 said:
I have the same problem on my PC at work, it's caused by a poor USB chipset in the PC, or trying to connect through a USB hub.
The only thing I found that worked was to try a different PC, then it was fine...
Click to expand...
Click to collapse
In my case it still happening in other computers. Conclussion: some piece of the software in the universal has been lost. The screen shows "Serial" that means on some way that is opened to comunication but not USB.
My questions are:
- should be possible to put some starting software in SD and do the universal boot on it.
- do you know how to connect to the computer COM! port from the usb miniport of the Universal.
I appreciate, I was not planning to replace now the Universal...
beginner said:
sl9 said:
I have the same problem on my PC at work, it's caused by a poor USB chipset in the PC, or trying to connect through a USB hub.
Now works.... I still thinking windows is so stupid software made for distroy our mind ....
Solved after install drivers for a converter usb -rs232 ( I was looking for the way to connect from rs232 the universal)
I'm happy again and I promise don't try to change rom again (at least for a while)
If some person is interested in what brand of software/hardware I installed, send me a mail...
Thanks hearing me ...
Click to expand...
Click to collapse
Click to expand...
Click to collapse
i have the same problem with my friend's uni
does it mean that you don't have to own any adapter, just have to install drivers for USB to RS232 adapter
if yes, where to find it?
thanx
respectfully
ZeD
zedino said:
i have the same problem with my friend's uni
does it mean that you don't have to own any adapter, just have to install drivers for USB to RS232 adapter
if yes, where to find it?
thanx
respectfully
ZeD
Click to expand...
Click to collapse
I want to say that is running after doing some things and obviously some of it solved my problems. I made:
- unistall last version of activesync and go back to version 4.0
- delete all the applications using ports usb.
due the connection still not running (windows message: device not recognized) and because in the screen of universal I saw: "COMM1" I tried to connect from computer port rs232. By that I purchased some special cable, name: hama brand, rs232 serial, 9 pin - usb.
As you can imagine all the steps I followed were followed by the typical restart of windows. In this sense is important to say that the universal, after connect, need to do a soft reset each time (again windows....)
Other comment is that I unmark the option to connect by usb in activesync and mark the connection by com1.
and after all was done, connecting by usb the unniversal, kill wcescomm, windows said "NEw usb device, sync device". I started mtty and now appears the USB option, great! same time the screen in universal changed from comm1 to usb, more great....
and that's all.
does it mean you solve your problem using special USB 2 RS232 connector?
ZeD
PS: it was my first idea , but i still believe i can solve the problem using USB port
zedino said:
does it mean you solve your problem using special USB 2 RS232 connector?
ZeD
PS: it was my first idea , but i still believe i can solve the problem using USB port
Click to expand...
Click to collapse
I think my english wording was not fine. I mean I solved my problem after install the sofware -drivers- of the rs232 connector, but connecting to the universal by usb as on standard way I was syncronizing previous the crack with activesync.
OK, where to get this driver?
thanx
?????????? NOTHING ?????????????
zedino said:
OK, where to get this driver?
thanx
Click to expand...
Click to collapse
Try here.
http://www.hama.de/portal/type*3/action*1026/searchMode*1/q*039703
I have had the same problem several times now (search the forum for the thread).
I tried three different PC's/laptops and three different USB cables all with the same error as yourself.
Eventually I got a connection but the laborious process of trying - failing, restarting windows and soft resetting the phone, trying - failing........... until it finally worked. I did nothing differently the time that it worked but the strange thing is that it has worked every time since! Maybe the USB driver the phone has a bug in it that causes it to get 'stuck' in a mode where it will no longer correctly operate but once you have managed to 'kick' it into action it seems toi then carry on working.
It was also a ROM upgrade that caused my USB phone driver to stop functioning. Maybe the fact that the phone has a slightly diffferent software configuration after the upgrade but exactly the same hardware fingerprint causes the driver to fail.
Every time that I have had this problem it is after an upgrade but once I have gotten it to work once with the new ROM, it always continues to function - until the next upgrade.
shrubbery said:
I have had the same problem several times now (search the forum for the thread).
I tried three different PC's/laptops and three different USB cables all with the same error as yourself.
Eventually I got a connection but the laborious process of trying - failing, restarting windows and soft resetting the phone, trying - failing........... until it finally worked. I did nothing differently the time that it worked but the strange thing is that it has worked every time since! Maybe the USB driver the phone has a bug in it that causes it to get 'stuck' in a mode where it will no longer correctly operate but once you have managed to 'kick' it into action it seems toi then carry on working.
It was also a ROM upgrade that caused my USB phone driver to stop functioning. Maybe the fact that the phone has a slightly diffferent software configuration after the upgrade but exactly the same hardware fingerprint causes the driver to fail.
Every time that I have had this problem it is after an upgrade but once I have gotten it to work once with the new ROM, it always continues to function - until the next upgrade.
Click to expand...
Click to collapse
not works, probably is this device lost forever, i have restarted device and PC almost hundred times, still the same result, uni stuck in Bootloader screen top of page "Serial" bottom of page "v1.00"
nothing changed, even if i connect to USB port
if someone have some solution to this s*it pls let me know
thanx
i have had the same. my device wast recognized by my pc, bur i used maupgradeno_id and installed a other rom, even installed the original rom from qtek (latest) then after i was finished it started then i tried the other rom and it was working. ( pc did see a unknown device ) hope you have the same and its working also.
good luck
mrijnvis said:
i have had the same. my device wast recognized by my pc, bur i used maupgradeno_id and installed a other rom, even installed the original rom from qtek (latest) then after i was finished it started then i tried the other rom and it was working. ( pc did see a unknown device ) hope you have the same and its working also.
good luck
Click to expand...
Click to collapse
no, my problem persist, hundred times i tried to recover friends device using upgrade by original shipped ROM but the device is not recognized by system so there is allways connection error, so this kind of reliving this UNI is not usable
anyway, thanx for raply and suggestion
ZeD
mrijnvis said:
i have had the same. my device wast recognized by my pc, bur i used maupgradeno_id and installed a other rom, even installed the original rom from qtek (latest) then after i was finished it started then i tried the other rom and it was working. ( pc did see a unknown device ) hope you have the same and its working also.
good luck
Click to expand...
Click to collapse
If you're stuck in bootloader mode only, visit www.buzzdev.netand look for ExitBootloader utility written by the great Buzz. Just follow his instructions or scroll thru' Universal's forum here and there for problems relating to "stuck in bootloader"
hope this helps
no device is not recognized by PC so any trying to use exitbl is not available, anyway this option was one of the first what i have tried
thanx anyway
ZeD
i had the same problem with the QTEK of my principal after I upgraded his ROMs.
(after the hard reset, the pocket remained in bootloader mode).
you can solve this problem in a very simple way:
you have to launch the bootloader installation (BL1.01_RUU_UNI_V.1.2.EXE) from the PC (still connected with the PPC through USB) while the PPC is in bootloader mode (on your display you see "USB > Serial 1.01" or something like that).
then you do a SOFT reset and the pocket boot normally.
very simple.
i hope to be helpful to someone.
zedino said:
no device is not recognized by PC so any trying to use exitbl is not available, anyway this option was one of the first what i have tried
thanx anyway
ZeD
Click to expand...
Click to collapse
I had some problem. After uninstall all usb applications in the pc and install the software for cable usb -rs 232, doing some softreset in the pda connected, it turned the screen message "Com" by "Usb"
Hi, I have reflashed my ROM I dont know how many times. Yesterday I tried to connect via activesync on a new ROM and it wouldnt connect. These are some of the things that happened:
Device orange charging light flashes a few times then goes off [never seen THAT before]
Activesyc menu comes up on device but activesync doesnt connect
Get 'this device can perform faster' message on desktop
Sometimes get USB devce not recognized on desktop
SOmetimes device orange charging light it stays on if I plug direct into PC but still doesnt activesync
I have tried to connect as DISK DRIVE but I dont see the device on my PC.
Have tried different ROMS, 6.5, 6.51, sense 2.1 and 2.5 but all have same issue. Have also tried connecting to other computers. same issue.
Have played around with USB to PC menu options (enable / diable faster data sync etc) but doesnt make a difference.
Anyone had this problems? Thoughts?
Have you tried diselecting "ask me 1st about usb connection type when I connect the device to the pc" under USB to PC settings
It worked for me
This is the exact problem I am facing!
I tried everything - as diskdrive, activesync (with/without speedup), etc.
On many ROMs, even the original one (WM6.1)
Can't connect - every PC gives an 'unknown device' and on some ROMs I cannot charge via USB, only via mains...
I also tried without the question on connection.
Just some thoughts:
Do you have corruptions on screen sometimes? (Some graphical glitches)
Any .CAB files you cannot install?
Did you try to reflash the same ROM more than once?
tried to connect without card in the device and in flight mode? (Uses less power)
With me it started after a ROM flash from Miri... (I don't blame him!!)
The Hard SPL did not give me any problem, the radio was not flashed, just the OS. But reverting did not help.
I certainly hope you will find a solution, since I have the exact same problem!!
Do you stil know what ROM you flashed when this problem occured?
I reverted to original ROM 6.1 AND 6.5 which included everything - boot, radio, os, stardup image. But it did not change!
I figured it out after trying everything i could: i think its a hardware problem. I have dropped my devicetoo many times, or plugged it in too many times. Who knows.
ekerbuddyeker said:
I figured it out after trying everything i could: i think its a hardware problem. I have dropped my devicetoo many times, or plugged it in too many times. Who knows.
Click to expand...
Click to collapse
And how did you figured it out? Did you return the device to the shop?
I have this exact same issue except I am on AthineOS... I thought it was my PC until I read these posts. No OS updates or any other machine updates were performed except on my device. Any clues as to a fix?
Somehow I don't think this is just hardware.
I did drop my device once, but that was even before first flash. After that it still worked.
So, some weeks later I HSPLed without any problem. After that the device still worked.
Then, after investigating which ROM to use I flashed the ROM a few days later.
Right after the first flash it all still worked. So, had to flash another and from that moment on the device cannot be reckognised by any PC.
I still think it has something to do with the flashing. I think the device does not give correct feedback when it receives some commands from PC (eg. the command to reply the device type/number)
Does anyone know a program which can check the USB port for the HTC Touch Pro 2? Just to test wheather the connector pins are ok?
download activesync 4.5 and run the setup. it will perform a repair. that usually solves the problem. if not, try a different usb cable and try plugging into different ports on your pc.
crazythunder said:
download activesync 4.5 and run the setup. it will perform a repair. that usually solves the problem. if not, try a different usb cable and try plugging into different ports on your pc.
Click to expand...
Click to collapse
These are the first things done. And this was already written in here.
It happens with many PCs, including some on which the device never connected to.
Also tried different cables, ports, etc.
Also disabled the fast transfer etc. etc.
Even tried several other ROMs, inclusding original Dutch 6.1 and Dutch 6.5
I'm having the same issue. I can connect via bluetooth, but not usb. And I'm stuck with 6.1. I was tole my phone was brand new, but now I'm starting to think otherwise.
waynehead05 said:
I'm having the same issue. I can connect via bluetooth, but not usb. And I'm stuck with 6.1. I was tole my phone was brand new, but now I'm starting to think otherwise.
Click to expand...
Click to collapse
Some questions, to verify this is due to flashing or is a fault in the design of the device...
- Where did you get the device?
- Have you flashed the device?
- Did you accidentally drop the device?
hi just to say had a completely orignal o2 xda orbit 1 flashed with new rom everything worked perfect before now active sync plays up i can sometimes connect but get usb device not reconigsed then click cross then pull out usb then reinsert then active sync connects works fully functional then after 5 min it disconects this is driving me mad as use active sync for a fast internet connection on my pda as my wifi is crap
Hi,
I just bought a s620 that runs wm5, but when I try to connect it to my pcs with the usb cable nothing happens... as if the phone wasn't there at all.
I tried on 2 different computers with 2 different usb cables. The phone charges fine and connects on activesynch via bluetooth... I even tried to hard reset it but I had no luck
Is the phone faulty? Have you got any ideas on how to fix it?
Thanks a lot.
SpaceFlyer said:
Hi,
I just bought a s620 that runs wm5, but when I try to connect it to my pcs with the usb cable nothing happens... as if the phone wasn't there at all.
I tried on 2 different computers with 2 different usb cables. The phone charges fine and connects on activesynch via bluetooth... I even tried to hard reset it but I had no luck
Is the phone faulty? Have you got any ideas on how to fix it?
Thanks a lot.
Click to expand...
Click to collapse
You need to install ActiveSync into your PC before it can recognize your phone. Also try using a different USB cable.
I did that on both the computers I have
SpaceFlyer said:
I did that on both the computers I have
Click to expand...
Click to collapse
Try another usb cable. if the problem still exist the problem might cause from usb pin from phone.
Maybe its hardware and your miniusb port is damaged, you can find good and cheap deals in ebay.
I can't even flash it with a wm6 rom this way :/
SpaceFlyer said:
I can't even flash it with a wm6 rom this way :/
Click to expand...
Click to collapse
You can still flash your phone thorugh your sdcard
gmaniac2008 said:
You can still flash your phone thorugh your sdcard
Click to expand...
Click to collapse
I tried, but I keet getting the invalid certificate error on some roms and nothing happens on others instead :/
SpaceFlyer said:
I tried, but I keet getting the invalid certificate error on some roms and nothing happens on others instead :/
Click to expand...
Click to collapse
Try this: http://forum.xda-developers.com/showthread.php?t=329605
u said that u connected via bluetooth, u said the phone charges when pluged....so i think your activesync its not configurated with a USB connection OR your phone isnt configurated to allow a USB connection to Activesync.
check activesync in the phone and in the PC to ALLOW USB CONECTION
se ya
flmhak said:
u said that u connected via bluetooth, u said the phone charges when pluged....so i think your activesync its not configurated with a USB connection OR your phone isnt configurated to allow a USB connection to Activesync.
check activesync in the phone and in the PC to ALLOW USB CONECTION
se ya
Click to expand...
Click to collapse
I have already another device that uses activesync via usb and that one works fine, I checked the settings btw.
gmaniac2008 said:
Try this: http://forum.xda-developers.com/showthread.php?t=329605
Click to expand...
Click to collapse
I followed the instructions on that thread, I get till the screen gets dark with the bt connection but then any ruu program obviously won't see the phone as it's not connected via usb. I even tried rebooting and getting in the manual bootloader after this but I kept getting the invalid certificate error, as if I didn't do anything at all.
Thanks for the help anyway.
SpaceFlyer said:
I followed the instructions on that thread, I get till the screen gets dark with the bt connection but then any ruu program obviously won't see the phone as it's not connected via usb. I even tried rebooting and getting in the manual bootloader after this but I kept getting the invalid certificate error, as if I didn't do anything at all.
Thanks for the help anyway.
Click to expand...
Click to collapse
You are running XP right on your computers and have access as administrator right? have you checked firewalls or antivirus settings that can be stopping the sync?? Reinstalling activesync?
Additionally, have you try on another computer with vista and WMDC?....I know vista is not as stable as XP, but I haven't had any issues so far with vista.
gmaniac2008 said:
You are running XP right on your computers and have access as administrator right? have you checked firewalls or antivirus settings that can be stopping the sync?? Reinstalling activesync?
Additionally, have you try on another computer with vista and WMDC?....I know vista is not as stable as XP, but I haven't had any issues so far with vista.
Click to expand...
Click to collapse
I tried on both xp and win7, my axim x30 is synching fine... so I don't think it's about settings.
The only option I have left at this point is the rom update I guess... if only it accepted the wm6 ones :/
Thanks.
I connected my SG2 via USB cable to my PC and started seeing this error
"One of the USB devices attached to this computer has malfunctioned and Windows does not recognize it. For assistance in solving this problem, click this message."
I have tried everything from changing cables/PCs/enabling/disabling USB debugging to *#7284#, and none of them work ...
Is the device bricked, is there any hope of revival..please help i got this phone myself paying $400
Does your phone turn on and work and a connection to PC the only problem? If so your not bricked...you prolly need to install the drivers in order for your PC to recognize it so install kies on your PC
Sent from my SGH-T989 using XDA App
Yes phone turns on, charges through the port...just that it is not recognized by the PC....what could be wrong?
As I said previously you probably need to add the drivers on your PC install kies on your PC
Sent from my SGH-T989 using XDA App
Make sure you use one of your rear usb ports also. I had an issue with drivers installing in a front usb port.
Phew it turns out to be the samsung driver..I believe kies update must have corrupted and stopped the pc from recognizing the phone....
seshsud said:
I connected my SG2 via USB cable to my PC and started seeing this error
"One of the USB devices attached to this computer has malfunctioned and Windows does not recognize it. For assistance in solving this problem, click this message."
I have tried everything from changing cables/PCs/enabling/disabling USB debugging to *#7284#, and none of them work ...
Is the device bricked, is there any hope of revival..please help i got this phone myself paying $400
Click to expand...
Click to collapse
The definition of "bricked" is having a really expensive
... brick. It means your phone doesn't turn on no matter what you do to it (short of a JIG and that's not guaranteed) the "USB device not recognized thing" is a problem w many windows devices my vista computer does it all the time and I just switch ports.
Sent from my SGH-T989
I had this problem. tried everything and never got my phone to connect toy laptop. What did you do?
Sent from my SGH-T989 using Tapatalk
Having same/similar issue
Hey, was there every a solution found for this?
I'm having basically the same problem...using the cable that came with my phone, and have installed Kies (fresh). I have tried toggling multiple settings. I tried uninstalling kies and reinstalling. I tried using pdanet for the driver. I have tried a few different roms, as well: Darkside 2.4, 2.5.1, and gingersnap 1.21. All have had the same result.
When I plug the phone in, it beeps (charging) but no notification for usb settings (disk drive, sync, etc). On my computer, it pops up "USB Device Not Recognized" and says the device has malfunctioned, etc, same as OP.
In Device Manager, it shows under USB as "Unknown Device".
I have tried this with two Windows 7 laptops, and a Windows Server 2008 R2 desktop. Also tried with a different cable. This cable was able to transfer data from an external hard drive today, so I doubt anything is wrong with it.
Any help is greatly appreciated!
Chino9656 said:
Hey, was there every a solution found for this?
I'm having basically the same problem...using the cable that came with my phone, and have installed Kies (fresh). I have tried toggling multiple settings. I tried uninstalling kies and reinstalling. I tried using pdanet for the driver. I have tried a few different roms, as well: Darkside 2.4, 2.5.1, and gingersnap 1.21. All have had the same result.
When I plug the phone in, it beeps (charging) but no notification for usb settings (disk drive, sync, etc). On my computer, it pops up "USB Device Not Recognized" and says the device has malfunctioned, etc, same as OP.
In Device Manager, it shows under USB as "Unknown Device".
I have tried this with two Windows 7 laptops, and a Windows Server 2008 R2 desktop. Also tried with a different cable. This cable was able to transfer data from an external hard drive today, so I doubt anything is wrong with it.
Any help is greatly appreciated!
Click to expand...
Click to collapse
Well I had the same problem with a new sgs2 i got witb the warranty. I even made a post about it. Tried everything and nothing fixed it. Had to do another warranty exchange
Sent from Flip's SGS2
Did you try the drivers separate first or Mtp mode
Sent from my revolutionized Samsung infuse
I tried without the drivers, and went to wireless and network > USB utilities. The only option in there, however, is "Connect storage to PC". If I try that, then plug it in, the phone acts like I hit the back/undo button. It doesn't show that anything is connected, nor does it give any other options. At this point on the computer, I get the "USB device not recognized" error.
This happened before installing Kies/Drivers, and still happens after installing drivers and kies.
try another usb cable
i had the exact same error, and it ended up being a good USB cable that went south
I will try a different cable when I get home - Have a month old cable for a mytouch 4g that I know works.
Okay, I tried it with the other cable, on a desktop in the rear port. same thing...Phone start to charge, and I get the error that the device malfunctioned, yada yada.
Any other ideas? Should I try to connect in Download mode?
Alrighty, so in the end, I ended up completely unroting, using terminal emulator to remove superuser.apk, busybox, and su and putting right back to read only. Then in CWM, flashed a stock 2.3.5 ROM (Zedomax). However, I now have the 2.3.5 ROM and the 2.3.6 KL1 Kernel...
I'm planning to return to Tmobile/Samsung - will the kernel and rom versions not matching be a huge red flag??
Any help is appreciated. I have tried to flash the 2.3.5 kernel, but I always get an error that it's not signed/verified.
Ideas?
I was hoping to grab the 2.3.6 OTA update, but it says there is no firmware update. Is there an update file I can put on the SD card and update using the stock recovery?
UPDATE:
I called T-Mobile Customer Service today, and went through the "troubleshooting" with them again. They ended up sending me a new one, overnight. They didn't ask anything about doing anything custom with it like rooting or other modifications.
I'm not sure if it made a difference, but I'm within 90 days, and also have the "best" insurance/warranty coverage through T-Mobile, and whoever their insurance provider is that I signed up for when I bought the phone.
Final charge is for $5, which I was told is some kind of fee from Samsung, but will appear on my bill.
Anyway, not too bad. Can't wait to get rid of touchwiz again when I get the new phone!
Chino9656 said:
Alrighty, so in the end, I ended up completely unroting, using terminal emulator to remove superuser.apk, busybox, and su and putting right back to read only. Then in CWM, flashed a stock 2.3.5 ROM (Zedomax). However, I now have the 2.3.5 ROM and the 2.3.6 KL1 Kernel...
I'm planning to return to Tmobile/Samsung - will the kernel and rom versions not matching be a huge red flag??
Any help is appreciated. I have tried to flash the 2.3.5 kernel, but I always get an error that it's not signed/verified.
Ideas?
I was hoping to grab the 2.3.6 OTA update, but it says there is no firmware update. Is there an update file I can put on the SD card and update using the stock recovery?
UPDATE:
I called T-Mobile Customer Service today, and went through the "troubleshooting" with them again. They ended up sending me a new one, overnight. They didn't ask anything about doing anything custom with it like rooting or other modifications.
I'm not sure if it made a difference, but I'm within 90 days, and also have the "best" insurance/warranty coverage through T-Mobile, and whoever their insurance provider is that I signed up for when I bought the phone.
Final charge is for $5, which I was told is some kind of fee from Samsung, but will appear on my bill.
Anyway, not too bad. Can't wait to get rid of touchwiz again when I get the new phone!
Click to expand...
Click to collapse
FYI, I just went through the same thing. Decided to finally root my phone after owning it for 2 weeks.
Phone nor the phone would recognize USB data, but would charge. Tried another cable and no luck.
Rebooted the phone. Works like a charm now.
Hi All, I've got a USB connection problem with my Galaxy Nexus. When I connect it to a computer, it will start charging, but doesn't show that it's connected to a computer and the computer doesn't show that a device is connected. I've tried on a few different Windows machines and don't get any change in the device manager. There is no "unknown device" nor device with an error. I've been searching the Internet and this forum, but still can't find the problem after a couple of days. Here's some details and things I've done:
I did not install the "force fast charge" kernel mod.
I've tried a couple different cables and verified that the cables worked with my wife's Galaxy II.
I've tried several different computers.
I've tried MTP and PTP storage options.
I rebooted everything several times.
I drank heavily.
I tried a factory reset.
I updated Windows Media Player to get the latest MTP software.
I installed drivers packages even though it never gets to the point of installing drivers.
Does anyone have any other ideas before I smash this thing with a hammer?
Does anyone have any ideas? At this point, I'm thinking there is a hardware problem.
Go into Menu -> System Settings -> Developer Options -> Turn on USB Debugging.
Not a guarantee, but something to rule out.
I've got USB Debuging on. Thanks for the reply.
Can anyone help? I'm having the same exact problem. My phone charge but is not detected by my computer. I am having this problem right after flashing AOKP ROM B35. This is very important, one mistake and my phone will be bricked as a computer to phone is so important !! There is nothing detected at all under device manager. Tried it on several laptop to make sure it isn't just my computer.
someone?
Uninstall the drivers you have for the s2. Reboot and install the official drivers for the galaxy nexus. Reboot. Then try.
If that doesn't work... let the phone load a while and just keep trying other ports on the computer. I saw this with my other gnex that it would take a while to realize a USB to be connected. Also make sure the USB is in completely... don't jam it in but make sure you know its All the way in. ( no pun intended) What's funny is my gnex will detect it instantly... but the other one takes a few tries.
Sent From My Sprint Galaxy Nexus via Xda Premium
Thank you dude. It doesn't work. Prior to installing this rom, my nexus is detected instantly. There is something wrong with the process i root or something. Now i can't do anything as It is not detected by my computer. Someone please help.
Indeed is the rom that is causing the problem. I opened NEXUS toolkit and rebooted my phone into boot image. It will sense it and i can operate from there. I've restored to factory and now my phone is being detected. I hope the thread starter gained something out of it too