Related
Good evening, kind forum readers.
Per the subject line, I find myself in possession of one misbehaving iMate-branded Blue Angel. Everything was working perfectly until a day and a half ago. Now the device is acting as though there is no SIM card inserted whatsoever.
As you might expect, there is no signal detected whatsoever. The 'Device Information' system applicaton reports no information for the Radio or Protocol version. There is no IMEI number listed on the Identity tab. Launching the 'SIM Manager' tool does nothing - the application never launches. When I do a soft reboot, it correctly lists the ROM verion on the startup screen, but says directly above it "No GSM". I've tried a hard boot and restore from a backup from about a week ago, no luck. I have tried with two SIM cards from two different providers, neither one produces any different results. Both cards work perfectly when inserted into another phone.
I am using the official 1.40.00 WWE ROM from iMate. When I try to reapply the ROM, I receive the "COUNTRY ID ERROR". I tried with an older third-party ROM that I had been using a while back, but that also aborts with the same error message.
Speaking with iMate support netted me the typical "Send it in to a service center" answer.
Hoping that someone else out there might have gone through something similar? Any thoughts/suggestions on how I might recover from this?
Regards,
Shawn.
http://wiki.xda-developers.com/index.php?pagename=BA_1.40.00_Upgrade
Try following the description on the link, go for the MaUpgradeUt_noID option.
Use this on your Original Rom, and try one upgrade at a time, Radio first, then OS, Don't see any reason to flash the Extended Rom
bosjo said:
Try following the description on the link, go for the MaUpgradeUt_noID option.
Use this on your Original Rom, and try one upgrade at a time, Radio first, then OS, Don't see any reason to flash the Extended Rom
Click to expand...
Click to collapse
I just tried this option, and it did progress further this time, but it produced the following error:
Device Software Update Utility - R2500 D1001 - CB2.07 -1
ERROR 114: RADIO ROM UPDATE ERROR
There has been a problem while updating your device software.
To continue the update, please:
1 Disconnect your device and the USB cradle.
2 Perfrom a normal reset by pressing the reset button (as left picture show).
3 Reconnect your device and the USB cradle and run this device software update program again.
Click Exit to quit.
Click to expand...
Click to collapse
Being something of a newbie in such matters, I didn't realize that I had to run GetDeviceData.exe first, so I didn't have a copy of DeviceData.txt. In that the device was not in a bootable state, I wasn't sure how to run the OS upgrade without the Radio upgrade. I ended up going with the decidedly unscientific but seemingly effective solution of just renaming the 'radio_.nbf' file. The OS and extended ROM both upgraded successfully. So now I'm back where I started - the radio is still not functioning.
Run the same upgrade this time with the radio.nbf and remove the other 2 nbfs.
Else ron the radio upgrade only of wiki using those files.
And if what MDAIIIuser says don't work.
Download the latest Rom upgrade from your wendor website,
extract the .exe file with a zip program,
delete the nk, ms, radio files,
Copy the 1.13 radio in there,
Run the BaUpgradeUt.exe
Or try to only delete the ms and nk files leaving what ever radio is in there, and run the BaUpgradeUt.exe
First time post ...
I recently downloaded the 1.13.53 WWE ROM update from the Imate site and attempted to install it on my JasJar. The update failed leaving my JasJar in boot loader mode. No reset method seemed to work to bring it back up. Subsequent attempts to load the ROM update gave me the dreaded "Country Code" error. Here are the steps I followed to get the ROM update to succeed:
1. Uninstalled ActiveSync 4.0 and installed ActiveSync 4.1 as downloaded from XDA FTP site. Disabled firewall and Anti-virus. Rebooted machine. I am not sure whether this step was neccessary or not but noted that others had some success with this. At this point I was still getting the country code error when trying to install ther update.
2. Run the update but once you get to the first screen that asks you if you want to proceed, switch to the Windows file system using Explorer and set the current directory to your TEMP directory. If you are not sure where this is, open a command prompt (Start - Run - CMD - OK) and type SET. This will display environment variables. Look for the one called TEMP - that is where you want to go.
3. Search for a file called ROMUpgradeUT.exe or RUU.conf anywhere in the TEMP directory or its subdirectories. When you find the correct directory, copy the files to a new location.
4. In the new location, edit the RUU.conf file and add the following text at the end of the file:
[CHECKCEID_TYPE]=1
5. Save the file and then run ROMUpgradeUT.exe
At this point I was able to get past the country code error and the update began. The radio upgrade was the first component and it took the most time (about 10-15 minutes). The other 2 components upgraded the extended ROM and the OS but only took about 5 minutes each.
After getting the completion message on my PC I also noted a "100% complete" message on the JasJar screen. After a hard reset (soft keys and reset) the JasJar came up with the upgraded ROM in place and I was REALLY HAPPY!
I don't know if this will work for anyone else - use at your own risk but I wanted to share what has worked for me.
BTW - many thanks to all the previous posters who left "breadcrumbs" for me to follow in getting my JasJar back. This community is SUPERB!
Thanks again.
Rick
Did like u said.
Still country id error
works now
thanks
my device t-mobile mda pro jasjar bootloader nope
rsteel1 said:
First time post ...
I recently downloaded the 1.13.53 WWE ROM update from the Imate site and attempted to install it on my JasJar. The update failed leaving my JasJar in boot loader mode. No reset method seemed to work to bring it back up. Subsequent attempts to load the ROM update gave me the dreaded "Country Code" error. Here are the steps I followed to get the ROM update to succeed:
1. Uninstalled ActiveSync 4.0 and installed ActiveSync 4.1 as downloaded from XDA FTP site. Disabled firewall and Anti-virus. Rebooted machine. I am not sure whether this step was neccessary or not but noted that others had some success with this. At this point I was still getting the country code error when trying to install ther update.
2. Run the update but once you get to the first screen that asks you if you want to proceed, switch to the Windows file system using Explorer and set the current directory to your TEMP directory. If you are not sure where this is, open a command prompt (Start - Run - CMD - OK) and type SET. This will display environment variables. Look for the one called TEMP - that is where you want to go.
3. Search for a file called ROMUpgradeUT.exe or RUU.conf anywhere in the TEMP directory or its subdirectories. When you find the correct directory, copy the files to a new location.
4. In the new location, edit the RUU.conf file and add the following text at the end of the file:
[CHECKCEID_TYPE]=1
5. Save the file and then run ROMUpgradeUT.exe
At this point I was able to get past the country code error and the update began. The radio upgrade was the first component and it took the most time (about 10-15 minutes). The other 2 components upgraded the extended ROM and the OS but only took about 5 minutes each.
After getting the completion message on my PC I also noted a "100% complete" message on the JasJar screen. After a hard reset (soft keys and reset) the JasJar came up with the upgraded ROM in place and I was REALLY HAPPY!
I don't know if this will work for anyone else - use at your own risk but I wanted to share what has worked for me.
BTW - many thanks to all the previous posters who left "breadcrumbs" for me to follow in getting my JasJar back. This community is SUPERB!
Thanks again.
Rick
Click to expand...
Click to collapse
this method how?my jasjar can open normal ?
help me
error 101 problem
error 150 problem
MaUpgradeUt_noID trying in my jasjar error problem 150 .whats saying ? problm where? usb dont recognize xp .what must ı do?
please help me im using Vista and cant get connection with my imate to my pc... and what is a radio update if you can help me add my msn!
i dont want to update anymore i just want to get my wm5!
Have a look here:
http://wiki.xda-developers.com/index.php?pagename=FlashVista
Hope it helps,
Okay,
I installed WM5 with no problem, but as a lot of my aps do not work on it, I am now trying to go back to Window 2003.
I have done all the needed stuff as told in the "How to Downgrade a WM5 Rom' (http://wiki.xda-developers.com/index.php?pagename=BA_Downgrade_WM5), but when I get at step 7, and run the 'MaUpgradeUt_noID.exe' (downloaded from the howto site) I get the following error:
Error 150: Rom Upgrade utility error
This ROM Upgrade Utility does not design for your device.
Please get proper ROM Upgrade Utility and try again!
Click to expand...
Click to collapse
(the 'MaUpgradeUt 'Device Software Update Utility - R1000 D1001' does also NOT show any info about the Device CE image version)
The ROM that I am trying to use is the same version as I was using before the WM5 update!
Anyone here who can help me with this error?
Nevermind... After rebooting the main pc, I got it to work.
So i downloaded WM6 Black 2.0, and its constantly crashing, so i wanted to re-install it and see if that helped.
now whenever i try to launch the file, i get an error message that states
"custom RUU has encountered a problem and needs to close. we are sorry for the inconvenience."
So im wondering what changed that wont allow me to run the ruu file? Im kinda freaking out here because i need to get my phone working! its constantly crashing on me!
i hope someone knows a fix for this, i tried to search but came up with nothing
newnoise1024 said:
So i downloaded WM6 Black 2.0, and its constantly crashing, so i wanted to re-install it and see if that helped.
now whenever i try to launch the file, i get an error message that states
"custom RUU has encountered a problem and needs to close. we are sorry for the inconvenience."
So im wondering what changed that wont allow me to run the ruu file? Im kinda freaking out here because i need to get my phone working! its constantly crashing on me!
i hope someone knows a fix for this, i tried to search but came up with nothing
Click to expand...
Click to collapse
Looks like a problem on your PC... (I mena for the Customruu crashing)
newnoise1024 said:
So i downloaded WM6 Black 2.0, and its constantly crashing, so i wanted to re-install it and see if that helped.
now whenever i try to launch the file, i get an error message that states
"custom RUU has encountered a problem and needs to close. we are sorry for the inconvenience."
So im wondering what changed that wont allow me to run the ruu file? Im kinda freaking out here because i need to get my phone working! its constantly crashing on me!
i hope someone knows a fix for this, i tried to search but came up with nothing
Click to expand...
Click to collapse
Had this happen to me. I downloaded .net framework 3.0 from the M$ site and then it worked fine.
Maybe that will help you.
Jim
Need more info?
newnoise1024 said:
So i downloaded WM6 Black 2.0, and its constantly crashing, so i wanted to re-install it and see if that helped.
now whenever i try to launch the file, i get an error message that states
"custom RUU has encountered a problem and needs to close. we are sorry for the inconvenience."
So im wondering what changed that wont allow me to run the ruu file? Im kinda freaking out here because i need to get my phone working! its constantly crashing on me!
i hope someone knows a fix for this, i tried to search but came up with nothing
Click to expand...
Click to collapse
Ok, first off, this is not a flame. It's an education, ok?
When posting a problem, it's best practice to let us know your:
Model of phone
Radio version
Boot Loader version
OS on your PC
ActiveSync version (s/b 4.5 by now)
Then, and only then, will you be able to get some intelligent answers. You also need to follow the link in my signature and there you will find answers.
If you're still stuck, usually re-downloading the RUU will result in a working ROM patch, unless you have other PC issues. You really need to fix that first, and the guides posted here are FULL of the diagnostic and troubleshooting steps that will propel you to a successful resolution.
Please read those posts, add your info, and you may be extremely pleased with the results.
Good reading!
newnoise1024 said:
So i downloaded WM6 Black 2.0, and its constantly crashing, so i wanted to re-install it and see if that helped.
now whenever i try to launch the file, i get an error message that states
"custom RUU has encountered a problem and needs to close. we are sorry for the inconvenience."
So im wondering what changed that wont allow me to run the ruu file? Im kinda freaking out here because i need to get my phone working! its constantly crashing on me!
i hope someone knows a fix for this, i tried to search but came up with nothing
Click to expand...
Click to collapse
First off; relax. At least the problem isn't with your phone. It's a heck of a lot easier to fix a PC.
I assume you've already tried to re-download the file?
Did you completely reboot your PC? Shut it down to power down, then restart. Make sure you don't have any extra USB stuff plugged in (like cameras, etc). If you have a PS/2 mouse and KB, use those, and not USB versions. One trick is to have the USB bus on your computer completely empty except for your phone.
Head over to Microsoft's site and download a fresh version of Compact Framework .NET (3.0 is the current version). Reboot after installing it -- even though it doesn't tell you to.
Run Windows Update. Make sure you're OK on those.
If that doesn't work, try downloading another ROM (OS only) -- like the Cingular Black 2.02 or the LVSM ROM, and see if that works.
You can also strip it apart -- use WinRAR to open the EXE file that you've been executing and extract the .nbh file from the EXE. Then go and download this guy: http://wiki.xda-developers.com/index.php?pagename=Hermes_CustomRUU and extract it into its own folder. Copy that .nbh file into that directory, and execute the executable -- it will flash your phone with a known good flasher.
But.... stepping all of the way back ... if the ROM doesn't work on your phone, it's very likely reflashing it won't help a single bit. Those ROM's are checksummed when they go on the phone -- if they're corrupted, they won't load right in the first place (and you'd end up with a boot-loader only phone). Soo... uh.. first, reboot/clean USB, then try a different ROM.
Last resort will be completely reinstalling Windows XP. I've had to do this several times because Windows will get in some weird state and it refuses to flash my phone. I finally gave up and started flashing on my Mac using a Windows virtual machine -- it's a lot easier to restore my Windows system to a working point when I do that.
Thanks to everyone who gave a response!
Here's all the information i was asked to post ( i will remember this for next time)
Cingular 8525 HERM100
Radio version: 1.40.30.00
Boot Loader version: (Not quite sure what this is?)
OS on your PC: Pro Black 2.0
ActiveSync version 4.5
I have redownloaded the ruu about 3 times and it has failed everytime.
Restarted the PC, disconnected everything from my laptop, realized that i havent installed Framework .NET 3.0, ( although i have it on my phone as i needed it to run hitchhiker)
So i'm going to download framework .NEt 3.0 and run it.
As for my phone, i uninstalled all the apps, hard resetted and everything is working fine right now, hasn't froze at all since yesteray, so im going to wait it out and see if something happens again.
Thanks again to everyone!! This forum is really really helpful.
-Matthew
How to determine the bootloader version
newnoise1024 said:
Boot Loader version: (Not quite sure what this is?)
-Matthew
Click to expand...
Click to collapse
You need to have a look at your user guide, as it states how to enter bootloader and check the version. Otherwise press and hold the left OK button and the power button at the same time, then hit the reset button with your stylus. You will enter a tri-color screen. This is bootloader mode. Jot down the numbers and compare against the below link.
Exiting is simple, press the reset button with your stylus.
Here's a valuable link for updating your bootloader.
Bootloader Version: SPL-1.40.01pro
IPL-1.01
i just tried to install Framework .NET 3.0 and got this error message
[04/20/07,08:50:20] Windows Communication Foundation: [2] Error: Installation failed for component Windows Communication Foundation. MSI returned error code 1603
[04/20/07,08:57:35] Windows Communication Foundation: [2] Error: Installation failed for component Windows Communication Foundation. MSI returned error code 1603
[04/20/07,08:57:54] WapUI: [2] DepCheck indicates Windows Communication Foundation is not installed.
[04/20/07,08:57:54] WapUI: [2] DepCheck indicates Microsoft .NET Framework 3.0 was not attempted to be installed.
i uninstalled any previous version, is there something i'm missing?
.Net Framework co-existence
newnoise1024 said:
Bootloader Version: SPL-1.40.01pro
IPL-1.01
i just tried to install Framework .NET 3.0 and got this error message
[04/20/07,08:50:20] Windows Communication Foundation: [2] Error: Installation failed for component Windows Communication Foundation. MSI returned error code 1603
[04/20/07,08:57:35] Windows Communication Foundation: [2] Error: Installation failed for component Windows Communication Foundation. MSI returned error code 1603
[04/20/07,08:57:54] WapUI: [2] DepCheck indicates Windows Communication Foundation is not installed.
[04/20/07,08:57:54] WapUI: [2] DepCheck indicates Microsoft .NET Framework 3.0 was not attempted to be installed.
i uninstalled any previous version, is there something i'm missing?
Click to expand...
Click to collapse
You're probably missing version 2.0 of the .NET framework. .NET Framework is to be left in place once installed. You should have left V 2.0 installed and added .NET 3.0. Go to www.microsoft.com/net and get version 2.0 redistributable re-installed on your machine. (If you can). If you cannot, search the KB and you may get by without rebuilding your OS.
"Head over to Microsoft's site and download a fresh version of Compact Framework .NET (3.0 is the current version). To be extra safe, go into Add/Remove Programs and uninstall any existing versions -- reboot -- then install the new CF Framework. Reboot after installing it -- even though it doesn't tell you to."
this is the advice i was given in this thread, so i uninstalled version 2.0 before installing version 3.0.
So am i screwed now? lol
Well, version 3.0 just installed successfully... does that mean i still need to install 2.0? or am i fine just running 3.0?
Sorry for all the questions, i just want this fixed :/
You should be good. Give it a go.
If not, just dl .Net CF2 and install that. I think you are fine now though.
Edit: never mind
version 2.0 installed fine
Thanks everyone
Disclaimer, use this at your own risk, if this voids your warranty I’m not being held responsible, blah blah all that junk.
Well, first, thanks go out for Microsoft for releasing a support tool for Windows Phone yesterday. Inside that tool, were unreal hidden gems.
Basically they’ve created a managed wrapper over the whole update process for us, rather nice of them.
So I flashed my HTC Mozart back to RTM (7004) via a ROM update HTC ship and whipped up a little application to flash pre-NoDo (7008), NoDo (7355), NoDo update 1 (7389) & NoDo update 2 (7390) all in a single process. No I don’t care which carrier you are on, which phone you have, it’ll just update your phone accordingly.
We really have to commend Microsoft here for being able to split up the OS updates into differential packs, which saves users downloading 200+ MB updates, unlike the IFruit updates.
All you need to do is run the ChevronWP7.Updater.exe console app and follow the prompts.
Make sure you select the RIGHT language for your device. To double check what your default language is, go to Settings > Keyboard and if your selected language is displayed in the Console app, you’re good to select it. If it isn’t in the list, DON’T flash it just yet.
Now, download the following files.
x86 Operating System (32 bit)
Windows Phone Support Tools
http://download.microsoft.com/download/1/5/4/15427EAF-AD42-4E4A-8179-9A3C5483E366/WPSupportTool-x86.msi
ChevronWP7.Updater
http://www.megaupload.com/?d=G1OEGML1
x64 Operating System (64 bit)
Windows Phone Support Tools
http://download.microsoft.com/downl...E4A-8179-9A3C5483E366/WPSupportTool-amd64.msi
ChevronWP7.Updater
http://www.megaupload.com/?d=40MA6F02
Once you’ve installed the support tools and extracted the ChevronWP7.Updater.zip to the desktop, plug your phone in and wait 30 seconds.
Now start ChevronWP7.Updater.exe (this should kill Zune) and follow the prompts.
If you’re updating from Version 7004, you need to run the Updater TWICE, this needs the preUpdate before we can flash NoDo.
Again, if your language isn’t in the Chevron updater, DON’T attempt to update your phone. Some of the applications won’t work otherwise.
This “might” work for HD2 owners, haven’t tried it out just yet. If it does, report below and tell me .
There is NO revert process, again, flash at your own risk.
I flashed my Samsung Omnia 7 works fine
Big Tenks to walshie
If I do so like you suggest with my HD2 (WP 7.0.7004.0), he still asks to update the february update..
And I did it twice like suggested...
Thanks anyway!
It doesn't work for me but I still have to install the February update. Does anyone know if there is already a new rom with this update included?
Thx!
Works for me, Samsung Focus AT+T and had to run it twice to get both updates.
Source
Where does this method pull the updates from? Is it the same update being tested by AT&T for the Focus?
Didn't work for me...tried 4 times and kept getting some error, then got booted from the program...not sure what the deal is. Samsung Focus, AT&T
Sent from my SGH-i917 using Board Express
Also not working for me- Samsung Focus on AT&T. Program runs, reboots phone, seems to update, but on examination I'm still at 7004.
Sadly I should've resisted. I did this on my AT&T Samsung Focus, everything is great except I have no marketplace and no Zune functionality..
LastOttoman said:
Disclaimer, use this at your own risk, if this voids your warranty I’m not being held responsible, blah blah all that junk.
Well, first, thanks go out for Microsoft for releasing a support tool for Windows Phone yesterday. Inside that tool, were unreal hidden gems.
Basically they’ve created a managed wrapper over the whole update process for us, rather nice of them.
So I flashed my HTC Mozart back to RTM (7004) via a ROM update HTC ship and whipped up a little application to flash pre-NoDo (7008), NoDo (7355), NoDo update 1 (7389) & NoDo update 2 (7390) all in a single process. No I don’t care which carrier you are on, which phone you have, it’ll just update your phone accordingly.
We really have to commend Microsoft here for being able to split up the OS updates into differential packs, which saves users downloading 200+ MB updates, unlike the IFruit updates.
All you need to do is run the ChevronWP7.Updater.exe console app and follow the prompts.
Make sure you select the RIGHT language for your device. To double check what your default language is, go to Settings > Keyboard and if your selected language is displayed in the Console app, you’re good to select it. If it isn’t in the list, DON’T flash it just yet.
Now, download the following files.
x86 Operating System (32 bit)
Windows Phone Support Tools
http://download.microsoft.com/downl...-4E4A-8179-9A3C5483E366/WPSupportTool-x86.msi
ChevronWP7.Updater
http://blog.walshie.me/Share/ChevronWP7.Updater.x86.zip
x64 Operating System (64 bit)
Windows Phone Support Tools
http://download.microsoft.com/downl...E4A-8179-9A3C5483E366/WPSupportTool-amd64.msi
ChevronWP7.Updater
http://blog.walshie.me/Share/ChevronWP7.Updater.x64.zip
Once you’ve installed the support tools and extracted the ChevronWP7.Updater.zip to the desktop, plug your phone in and wait 30 seconds.
Now start ChevronWP7.Updater.exe (this should kill Zune) and follow the prompts.
If you’re updating from Version 7004, you need to run the Updater TWICE, this needs the preUpdate before we can flash NoDo.
Again, if your language isn’t in the Chevron updater, DON’T attempt to update your phone. Some of the applications won’t work otherwise.
This “might” work for HD2 owners, haven’t tried it out just yet. If it does, report below and tell me .
There is NO revert process, again, flash at your own risk.
I flashed my Samsung Omnia 7 works fine
Big Tenks to walshie
Click to expand...
Click to collapse
In the future, just link directly to my Blog, direct linking to the installers doesn't enable me to update them if there is an issue.
so i shouldn't be doing this if i have Samsung Focus on AT&T?
mastamind518 said:
so i shouldn't be doing this if i have Samsung Focus on AT&T?
Click to expand...
Click to collapse
If you follow the post, there are detailed instructions for Samsung Focus users.
walshieau said:
If you follow the post, there are detailed instructions for Samsung Focus users.
Click to expand...
Click to collapse
thanks it worked. shows 7390.
Focus
Worked for me too on my ATT branded, locked Samsung Focus. Now running 7390.
Have an AT&T Focus, carrier unlocked, Chevron'ed and I can't seem to update. I have tried using the "Windows Support Tool" and still no luck. See log below if it looks right
UpdateWP version 4.7.1404
Applying updates to device
Id: \\?\usb#vid_045e&pid_0710#b7d536af-3362-ca4a-6b09-6f8888553bf1#{ca3d7387-f67b-11da-bbec-8000600fe800}
SN: af36d5b7 - 62334aca - 6b096f88 - 88553bf1
Name: SGH-i917
KITLName: QSD8XXX19417BBB
Manufacturer: SAMSUNG
ModelId: 1
MobileOperator:
Version: 07.00.07004.00-00000
Checking your phone's status.
Checking your phone's status: Completed in 0.01 seconds
Checking system requirements.
Checking system requirements: Completed in 0 seconds
Downloading updates.
Downloading updates: 0%
Downloading updates: Completed in 3.07 seconds
Checking system requirements.
Checking system requirements: Completed in 0 seconds
Installing updates. Please wait: 100%
Installing updates. Please wait: Completed in 5.57 seconds
Rebooting your phone..
Rebooting your phone: Completed in 42.3 seconds
Completing updates..
Completing updates: Completed in 1.28 seconds
The device has been updated to version 07.00.07004.03-00.00.00000.00-00.00.00000.00
When i look at the "About" status it still shows 7.00.07004.0
Any ideas?
Hi, HTC Surround
I am updating and it goes to downloading update but fails to go any further. just closes chevron
Any Ideas
Updated fine, but after the update anything related with messaging (SMS's, E-mail some contacts) doesn't work. Orange HTC Mozart running branded 7008...
Chevronwp7update was removed from the site. Where else can it be downloaded from?
Same here HTC Mozart telstra
Sent from my T8697 using XDA Windows Phone 7 App
Updater seems to be offline?
Anyone has got updated Links or a mirror?
Thanks in advance
Ok, I installed the Debrander xap util and it debranded to 00-88. I then ran Zune and it showed update available. It upgrade phone to 7008 from 7004. But even after that running chevron update still fails.
Maybe it was pulled from the site due to unforeseen problems.
Btw, don't reinstall debrander over your original debrander as it loses the original carrier details no I cannot rebrand to at&t unless I do a reg hack *I think*