Related
Okay, I've finally got WM6 on my HX2110. For any other people having the same problems I did, here is exactly what I did. What the guides I've found don't tell you is where to find it, and what to do when you get it. Basically you need to trick the iPaq into thinking it's getting the original 1.00.00.l firmware and then switch firmwares. You need to downgrade to the original H firmware before the iPaq will accept wm6. This worked perfectly for me after two days of trial and error. More detailed steps are below, but basically its: flash with 100l, reset, run 100l and swap firmware with 100h, flash, run 100l and swap with wm6, flash
Prerequisites:
Advanced_pack_for_hx2xxx_to_WM6
iPaq HX2110
USB connection to computer
1) Hard reset iPaq. Do this by holding the calendar button and itask button (curved arrow), and then put your stylus into the reset hole on the bottom of the iPaq. This will hard reset it.
2) After doing that, put it in to bootloader mode. You do this by holding the contact button (to the right of the calendar) and the itask arrow, and then clicking the reset button on the bottom. It should now be in bootloader mode. unplug the power/usb cable and plug it back in. hit the calendar button. it should now say USB.
3) run hpRUU.exe under the Wm5.0 for hx2000_1.00.00.L_ENG folder. It's found in provishki. it will flash your ipaq to 1.00.00.l . let it flash all the way.
4) hard reset the ipaq and put it in bootloader mode. see steps 1 and 2. make sure it says USB.
5) do step 3 again, but this time don't click upgrade. rename the E1_Upgrade_ROM_v1_00_00_L_SIGNED.nbf file to 100l.nbf
6) go into the SP32408_1.00.00.H_ENG folder and get the NBF file from there. copy it into the 1.00.00.L folder that we were just in. rename is to E1_Upgrade_ROM_v1_00_00_L_SIGNED.nbf. click upgrade. let the upgrade finish.
7) repeat steps 1 and 2.
8) delete the E1_Upgrade_ROM_v1_00_00_L_SIGNED.nbf file that you just copied over and rename the 100l.nbf file to E1_Upgrade_ROM_v1_00_00_L_SIGNED.nbf.
9) run hpruu.exe again. DO NOT CLICK UPGRADE.
10) get the wm6_wwe.nbf file and copy it into the directory we were just in. rename E1_Upgrade_ROM_v1_00_00_L_SIGNED.nbf to 100l.old and wm6_wwe.nbf to E1_Upgrade_ROM_v1_00_00_L_SIGNED.nbf
11) click upgrade. let it finish.
12) repeat step 1
you should now have Windows Mobile 6 on your iPaq. Good luck
I've been finding things that said I need to downgrade my firmware to 1.00.00.h after doing the 1.00.00.l version. I can't find L for the life of me. All I need is for someone to show me where I can get it. The only sites that bring anything up about that are russian.
jsbarone said:
I've been finding things that said I need to downgrade my firmware to 1.00.00.h after doing the 1.00.00.l version. I can't find L for the life of me. All I need is for someone to show me where I can get it. The only sites that bring anything up about that are russian.
Click to expand...
Click to collapse
Hi jsbarone
You may study and try from this:
http://forum.xda-developers.com/showthread.php?t=330682
hkksl said:
Hi jsbarone
You may study and try from this:
http://forum.xda-developers.com/showthread.php?t=330682
Click to expand...
Click to collapse
More info found here
http://forum.xda-developers.com/showthread.php?t=329079&page=9
updated with my guide on flashing my hx2110. it worked well for me. it's not perfect but hopefully it will help someone with the same problems I had.
Thanks Man you saved my day... everything worked fine!!!
At last, I done an upgrade to WM5 (still waiting for help to understand how to upgrade to WM6)...
May I Ask A question?
Everyone doing an upgrade have a slower PDA?
cant make it work :-(
i did precisely as described in this article, but now i got a "bricked" HX2110.
I only get to the loading screen with the version 5.20.00.H ENG
Someone had an idea??
Thanks!!
//Pzymex
pzymex said:
i did precisely as described in this article, but now i got a "bricked" HX2110.
I only get to the loading screen with the version 5.20.00.H ENG
Someone had an idea??
Thanks!!
//Pzymex
Click to expand...
Click to collapse
The answers are all in the Posts above.
Hkssl:
But that was i did.. My device is not even able to boot in any of theese steps..
should the device be able to boot after every upgrade???
but i will try again...
pzymex said:
But that was i did.. My device is not even able to boot in any of theese steps..
should the device be able to boot after every upgrade???
but i will try again...
Click to expand...
Click to collapse
i might find the problem, i think i started with wm2003. do i need any prerequities to upgrade from WM2003 to wm6??
and what to do when I already bricked my hx2110?
something it's not clear for me... When we run hpruu and 100% of instalation it's complete the devive restart it self. Do we have to wait there? wen do we have to do the hard reset?
I did it!
my advices are
1)start installing from windows mobile 2003
2) do not restart the pocket pc before the windows log-in screen appears!
Good luck!
Thanks!
sorry for my english
So many thanks for your tips.
I have some friends who couldn't flash by ordinary steps, I hope your guides will solve their problem on upgrading to my Thai Customized WM6.1.
Cheers,
Keng230
pzymex said:
But that was i did.. My device is not even able to boot in any of theese steps..
should the device be able to boot after every upgrade???
but i will try again...
Click to expand...
Click to collapse
My device is Original WM2003, are there any prerequities before doing the upgrade mentioned in this article?
Hi!
I'm having some problems with my Hx2110...
When flashing my working ipaq (Step 6), my computer halt.
So, i run HPRUU to reflash again, with no luck (because of "incorrect device SKU). Of course, model ID returned of my bricked IPAQ is "¨¨¨¨¨¨¨"...
But i have another chance, i try universal bootloader and USB telnet, (USB> prompt never come. (Pre-Bl screen and USB on ipaq screen are ok.)
I've tried every solution in this forum, and on internet.. (well, there's a hpruu.exe patched to ignore lang/model, but is for 6xxx series only )
What happen if i put a working 2110 on cradle, when hpruu comes with UPDATE screen, disconnect usb, and connect my non-working ipaq?...this will work?. I can try this on monday.
Thanks!
2) After doing that, put it in to bootloader mode. You do this by holding the contact button (to the right of the calendar) and the itask arrow, and then clicking the reset button on the bottom. It should now be in bootloader mode. unplug the power/usb cable and plug it back in. hit the calendar button. it should now say USB.
I just have to ask this:
What we should do before Unpluging powe/usb cable and plug it back in ???
Does it means that after putting it in bootloader mode i must put it on a cradle, then unplug power/usb cable and then again plug in it and press the calendar button ??? Or else ?
Greets, Janeku
people who installed wm6 on ur hp2110, are u satisfied with it?
Guys I Need Heeelp!!
Hellow Everyone! I am having a Hx2400 With WM5 Spanish and Firmware Version 1.02.00.H. Since i don't know any Spanish i want to upgrade to WM6 English.
I don't understand what i am supposed to.... Pleeeeease Help Me ...
I had followed jsbarone instruction but after step 3, i can not put my hx2110 on bootloader mode.i don't understand why?? i put the stylus into the softreset hole but it won't work. and then it shut down.now even i cannot turn it on (i mean put the cradle power on ) so if anyone know why please help me to fix it up !!!
after increased battery usage with crc 11.2
i decide to change to schaps 4.40 beta!
after correct installation and restart of the device
i get a screen which cannot be removed!
every key which i press is not working and this screen is still appearing.
Now i cannot not connect with active sync to change the rom again (((
what can i do now??????
plz help urgently.
The screen that appears says following..
"This concludes the beta test of this software release. thank you very much for your time and effort in helping make this a great product for our customers.
to obtain a newer release or further information, please revisit the web site that you used to obtain your current beta release."
Thanks in advance!!
B'R'
good approach, sticky thread
come on man, if you don't know what "beta software" means, google it
quick solution: put your device in bootloader mode (by pressing both Power and OK buttons and with the stylus pressing and holding the Reset button at the bottom of your device ) and then flashing a new ROM like normal.
reliable solution: surfing enough at the wiki pages http://wiki.xda-developers.com/index.php?pagename=HTC_Hermes
reading the comments on the ROM which represent User Experience before f***ing up your device
Ok Remove your memory card and connect it to the computer.
Then Extract your favourite ROM to a temp directory on your computer. There will be nbh file. Rename it to HERMIMG.nbh and copy it to the root of the memory card and insert it to the PDA. Now get into the bootloader mode by pressing the POWER+OK button on the Left side of your PDA, below the scroll wheel+HARD RESET using your stylus. Upon restart the PDA will automatically start installation of new rom. No need of activeSync.
Enjoy
Put Manually Bootloader and flash another rom again.
The bootloader is invoked by pressing down both the POWER button and SIDE OK together and using the stylus at the same time to press the RESET button at the bottom.
Amazing Synchro guys. We are real Helpers!!!!
lagoskon said:
Amazing Synchro guys. We are real Helpers!!!!
Click to expand...
Click to collapse
yeah man, we learned how to stop ignoring or only insulting new users but we forgot to tell him not to post a new thread for such a question next time.
hi!
i get only the usb notification on screen but no connection on pc
B'R'
flashing from micro sd card
try this:
http://wiki.xda-developers.com/index.php?pagename=Hermes_SDCardFlashing
mimahitna said:
try this:
http://wiki.xda-developers.com/index.php?pagename=Hermes_SDCardFlashing
Click to expand...
Click to collapse
i don't have a card yet :/
Get one ??? or do you want the guys to manufacture you one?
loco09 said:
after increased battery usage with crc 11.2
i decide to change to schaps 4.40 beta!
after correct installation and restart of the device
i get a screen which cannot be removed!
every key which i press is not working and this screen is still appearing.
Now i cannot not connect with active sync to change the rom again (((
what can i do now??????
plz help urgently.
The screen that appears says following..
"This concludes the beta test of this software release. thank you very much for your time and effort in helping make this a great product for our customers.
to obtain a newer release or further information, please revisit the web site that you used to obtain your current beta release."
Thanks in advance!!
B'R'
Click to expand...
Click to collapse
YOU DON'T NEED TO FLASH WITH SD CARD.
1: Do a HARD RESET. (hold the two soft keys then press reset with stylus).
2: at reboot connect with activesync but DON'T ESTABLISH A PARTNERSHIP WITH ACTIVESYNC.
3:flash your hermes with another rom, that's all.
The simplest thing to do is just to put it into bootloader mode, connect to pc the then flash with another ROM. In less than 10 min. you're done.
Cheers!!
I recently purchased two M88 Miphones from China (Windows Mobile 6.0 version). Both were supposed to be in English but when they were shipped to me, one was in English and the other Spanish. How can I change the language from Spanish to English? Or maybe I can install an entirely new English version of Windows Mobile 6.0? Can I extract the ROM from the English one and use it for the other (Spanish) one? Please help. Thanks.
It's great to find a way to install or restore the Windows on M88. My one just died. I haven't access to anything but the "phone" functions, so i need to restore it somehow from my PC. Some advices?
snakemountain said:
I recently purchased two M88 Miphones from China (Windows Mobile 6.0 version). Both were supposed to be in English but when they were shipped to me, one was in English and the other Spanish. How can I change the language from Spanish to English? Or maybe I can install an entirely new English version of Windows Mobile 6.0? Can I extract the ROM from the English one and use it for the other (Spanish) one? Please help. Thanks.
Click to expand...
Click to collapse
Hi, I think there is a way to change your Windows to English. I received the same phone with the same problem. I wrote to the supplier and they respond with the decision: they provided the original english WM6 ROM for M88 MiPhone on the website, so you can download it from here: http://rapidshare.com/files/168534489/DX.SKU16783.UPDATE.ENGLISH.AUG01.rar
But my problem is that I can't go in to the bootloader mode - just don't know how so to start loading the Windows OS. The instructions on the site are very poor and don't work. So I'm stuck again. Here there are the instructions:
"English OS System 20080801 Edition (ROM image) available for download
- To update ROM, format your TF card with FAT32 and unzip all files and folders from the downloaded file into the root folder of the TF card. Then, restart the phone to begin updating. This update converts all non-English versions of this phone into English version."
And some more instructions from my correspondence with the supplier, which shows different way of putting the phone in to the bootloader mode:
"we have a better idea to solve this inconvenience for you
we had updated a file on our website for you
you can download it and put it in your memory card to update the language into English.
you can put the file in the memory card no need to creat a folder for it
and insert the card into your cellphone
press the power bottom and the home bottom together
a few second later there would be a message on the screen shows you can press the home bottom again to restart the cellphone"
So maybe you can see they are showing different ways to enter the boot loader. Neidher 2 of them are working for me.
Since I have this phone I didn't find a way to enter the bootloader mode! I tried every combination between the keys but NOTHING! The only thing what I can do with the buttons is SWITCH OFF, SOFT RESET AND HARD RESET.
Please if somebody discover how to do that on that phone -M88 to share here with the rest of us!
Best of luck!
teddy_irish said:
Hi, I think there is a way to change your Windows to English. I received the same phone with the same problem. I wrote to the supplier and they respond with the decision: they provided the original english WM6 ROM for M88 MiPhone on the website, so you can download it from here: http://rapidshare.com/files/168534489/DX.SKU16783.UPDATE.ENGLISH.AUG01.rar
But my problem is that I can't go in to the bootloader mode - just don't know how so to start loading the Windows OS. The instructions on the site are very poor and don't work. So I'm stuck again. Here there are the instructions:
"English OS System 20080801 Edition (ROM image) available for download
- To update ROM, format your TF card with FAT32 and unzip all files and folders from the downloaded file into the root folder of the TF card. Then, restart the phone to begin updating. This update converts all non-English versions of this phone into English version."
And some more instructions from my correspondence with the supplier, which shows different way of putting the phone in to the bootloader mode:
"we have a better idea to solve this inconvenience for you
we had updated a file on our website for you
you can download it and put it in your memory card to update the language into English.
you can put the file in the memory card no need to creat a folder for it
and insert the card into your cellphone
press the power bottom and the home bottom together
a few second later there would be a message on the screen shows you can press the home bottom again to restart the cellphone"
So maybe you can see they are showing different ways to enter the boot loader. Neidher 2 of them are working for me.
Since I have this phone I didn't find a way to enter the bootloader mode! I tried every combination between the keys but NOTHING! The only thing what I can do with the buttons is SWITCH OFF, SOFT RESET AND HARD RESET.
Please if somebody discover how to do that on that phone -M88 to share here with the rest of us!
Best of luck!
Click to expand...
Click to collapse
Hi, I'm From Brazil
I'm selling this phone here in my country.
I think I've got same problem here. But I've tried to get bootscren and it seems to be that procedure correct.
Once you shutdown the phone first remove it battery for 10 seconds, and than put back into the phone. Than press power and home(that center buttom) until phone show 2 messages(one for master boot and other for clear boot).
After this message you may release power buttom and keep pressing home buttom untill phone shows it boot screen.
You will face a "downloading program, please wait" message on phone screem
But be extremelly carefull than, make sure you have a power cable attached to the phone and it battery at least 90% charged because update took lot of time sometimes.
I'm telling that because today I have one M88 "dead" in my hands because I did not followed all this procedure and after 35 minutes, by mystake I pressed reset buttom.
Now my phone not even turns on, nor charge it battery, is dead.
But I think using one of those "BOX" devices I will ressucitate it!
Thanks m8!
The thing is that when I press the 2 buttons at once I can only get blue screen for less than 1 second and after that Windows is loading. When it is done - the phone is after hard reset. I've tried hundreds of times - always the same. I can't get messages asking me to load software - only hard reset is the result. I've tried any other combination, including the reset buton under the cover, next to USB, but never managed to enter the service mode or boot mode or whatever it is.
One week I'm wasting my time in doing hundreds of attemts to enter the bootloader and nothing! How then do you make a hard reset on the M88?
Do you thing if I can use backup from english version of the same model that will change the situation - the spanish will be substituted by english? And if it's possible can you upload such a backup, made by Spb backup software for me, please?
Best regards
I have stupid problem. Some files disappeared, some programs stopped working and the entire system blocked. I made many soft and hard resets, which fixed the things... for a while. After one hour it's blocking again, without any settings, or interventions.
I downloaded the ROM, created a "root" folder in the card and unzipped everything there.
The thing is that it ROM-boot looks too fast - only couple of minutes. Can it be?
teddy_irish said:
Thanks m8!
The thing is that when I press the 2 buttons at once I can only get blue screen for less than 1 second and after that Windows is loading. When it is done - the phone is after hard reset. I've tried hundreds of times - always the same. I can't get messages asking me to load software - only hard reset is the result. I've tried any other combination, including the reset buton under the cover, next to USB, but never managed to enter the service mode or boot mode or whatever it is.
One week I'm wasting my time in doing hundreds of attemts to enter the bootloader and nothing! How then do you make a hard reset on the M88?
Do you thing if I can use backup from english version of the same model that will change the situation - the spanish will be substituted by english? And if it's possible can you upload such a backup, made by Spb backup software for me, please?
Best regards
Click to expand...
Click to collapse
I think I can do that,
but in one and half week because I'm still waiting for the flashing box and their cables.
Once I get I will upload it here.
ZEMONTI said:
I have stupid problem. Some files disappeared, some programs stopped working and the entire system blocked. I made many soft and hard resets, which fixed the things... for a while. After one hour it's blocking again, without any settings, or interventions.
I downloaded the ROM, created a "root" folder in the card and unzipped everything there.
The thing is that it ROM-boot looks too fast - only couple of minutes. Can it be?
Click to expand...
Click to collapse
Go ahead
But be pretty calm when performing update or you gonna get a bricked phone.
But is it possible that the update takes only few minutes? Or i'm doing only hard reset?
It is possible the update to take only few minutes
ZEMONTI said:
But is it possible that the update takes only few minutes? Or i'm doing only hard reset?
Click to expand...
Click to collapse
Hi from Ireland!
Yes it's possible. Today I finally managed to make the update - it took only 3 minutes. Now I have English OS on my M88!
It's a really nice phone isn't it?
Regards
teddy_irish said:
Hi from Ireland!
Yes it's possible. Today I finally managed to make the update - it took only 3 minutes. Now I have English OS on my M88!
It's a really nice phone isn't it?
Regards
Click to expand...
Click to collapse
That's good news!
Yes It is!
How to install WM6 ROM - English version on M88 MiPhone from SD card
Please download the original ROM from here
I was adwised to do this:
1. Duplicate the update.img file and rename the second one as "uploader"
2. Copy both "update.img" and "uploader" on the SD - formatted in FAT32
3. Press POWER and HOME butons at the same time.
4. There are two possible options from here:
a) White screen with blue text showing "Upload image... please wait..."
b) Red screen with the options what to do in the next step -
5. I saw first the a) option - the white screen. So after 3 minutes of waiting the phone said it is done and it will selfrestart.
After the restart it will load the English OS on your M88
Enjoy
the mine is dead too.
stenatay said:
hi, i'm from brazil
i'm selling this phone here in my country.
I think i've got same problem here. But i've tried to get bootscren and it seems to be that procedure correct.
Once you shutdown the phone first remove it battery for 10 seconds, and than put back into the phone. Than press power and home(that center buttom) until phone show 2 messages(one for master boot and other for clear boot).
After this message you may release power buttom and keep pressing home buttom untill phone shows it boot screen.
You will face a "downloading program, please wait" message on phone screem
but be extremelly carefull than, make sure you have a power cable attached to the phone and it battery at least 90% charged because update took lot of time sometimes.
I'm telling that because today i have one m88 "dead" in my hands because i did not followed all this procedure and after 35 minutes, by mystake i pressed reset buttom.
Now my phone not even turns on, nor charge it battery, is dead.
But i think using one of those "box" devices i will ressucitate it!
Click to expand...
Click to collapse
i am passing through the same. What do you mean with box. I need to ressuciatate it
please.
[email protected]/ [email protected]
helllp
stenatay said:
hi, i'm from brazil
i'm selling this phone here in my country.
I think i've got same problem here. But i've tried to get bootscren and it seems to be that procedure correct.
Once you shutdown the phone first remove it battery for 10 seconds, and than put back into the phone. Than press power and home(that center buttom) until phone show 2 messages(one for master boot and other for clear boot).
After this message you may release power buttom and keep pressing home buttom untill phone shows it boot screen.
You will face a "downloading program, please wait" message on phone screem
but be extremelly carefull than, make sure you have a power cable attached to the phone and it battery at least 90% charged because update took lot of time sometimes.
I'm telling that because today i have one m88 "dead" in my hands because i did not followed all this procedure and after 35 minutes, by mystake i pressed reset buttom.
Now my phone not even turns on, nor charge it battery, is dead.
But i think using one of those "box" devices i will ressucitate it!
Click to expand...
Click to collapse
help me, the mine is dead.
how per-say?
teddy_irish said:
Hi from Ireland!
Yes it's possible. Today I finally managed to make the update - it took only 3 minutes. Now I have English OS on my M88!
It's a really nice phone isn't it?
Regards
Click to expand...
Click to collapse
how persay did u get past the blue screen?
hello I am of chili and my m88 non reconose the card of cellular neither the icon of the cellular one needs urgent operative elsistema and the program and naturally like one makes before hand thank you
Hello every one,
I have this phone too, I trying to find any way or a cab to send the audio from the Fm radio app to the bluetooth headset, but no progrees, it only works with the original eraphones,
Any one have an a idea woh to do it?,
Regsards.
Javier.
jaguerra said:
Hello every one,
I have this phone too, I trying to find any way or a cab to send the audio from the Fm radio app to the bluetooth headset, but no progrees, it only works with the original eraphones,
Any one have an a idea woh to do it?,
Regsards.
Javier.
Click to expand...
Click to collapse
Me too. I was intending to lessen some audio-books.
Does it requires some additional software?
so how did it go and whats the name of the box i need one kinda kill my phone as well
please give info if u have it
M88 english bootloader
Here is the fix, sponsored by wirelessandmorestore.com
Copy both of these files to your computer.
http://uploading.com/files/YE6JJ36Y/update.img.html
http://uploading.com/files/TA1N0MBA/uploader.img.html
Plug in your phone and copy them to the SD card.
Turn the phone off.
Press the button on the top and the round button on the face at the same time and continue to hold it. As you are holding it, the phone will turn and go thorugh a couple steps before it says something like 'downloading image' or 'updating image' something like that.
Once it gets to that screen, you can let go of the buttons and the phone will update and reboot. This will take a couple of minutes. It will be in English when it turns itself back on and loads Windows.
English OS System 20080801 Edition (ROM image) for M88 MiPhone
Please download from here
If somebody knows how to enter the bootloader mode of this phone please share here with us!
Here is the instruction for this procedure from the supplier which is nor working for me:
"English OS System 20080801 Edition (ROM image) available for download
- To update ROM, format your TF card with FAT32 and unzip all files and folders from the downloaded file into the root folder of the TF card. Then, restart the phone to begin updating. This update converts all non-English versions of this phone into English version."
If somebody can manage to install the ROM please write here the steps!
Thanks!
You can get to the flash update by pressing RESET, MENU, and POWER all at the same time, then release RESET first and wait for a message. The message will tell you to release POWER to do a hard-reset or MENU to do a flash update. In this case, you will release MENU first, then you will get a message asking if you want to update from SD. At this point, none of the buttons do anything so I assume you have to tap the touchscreen. My touchscreen is broken so I couldn't get any further than this.
Problem Fixed!
GnatGoSplat said:
You can get to the flash update by pressing RESET, MENU, and POWER all at the same time, then release RESET first and wait for a message. The message will tell you to release POWER to do a hard-reset or MENU to do a flash update. In this case, you will release MENU first, then you will get a message asking if you want to update from SD. At this point, none of the buttons do anything so I assume you have to tap the touchscreen. My touchscreen is broken so I couldn't get any further than this.
Click to expand...
Click to collapse
Thanks for your help, m8. It didn't work that way for me. I was adwised to do this:
1. Duplicate the update.img file and rename the second one as "uploader"
2. Copy both "update.img" and "uploader" on the SD - formatted in FAT32
3. Press POWER and HOME butons at the same time.
4. There are two possible options from here:
a) White screen with blue text showing "Upload image... please wait..."
b) Red screen with the options what to do in the next step -
5. I saw first the a) option - the white screen. So after 3 minutes of waiting the phone said it is done and it will selfrestart. After the restart - voila! There was the English OS loaded on my phone and everything was working perfect!
Hope this to help to other people too!
Wow! It was very detailed and finally i resolved my problem. Thanks!
Does somebody knows how can i uninstall the fung S2U2? It causes a lot of problems with the horizontal screen ant others. It's not in the list of "remove programs".
Check this out:
ZEMONTI said:
Wow! It was very detailed and finally i resolved my problem. Thanks!
Does somebody knows how can i uninstall the fung S2U2? It causes a lot of problems with the horizontal screen ant others. It's not in the list of "remove programs".
Click to expand...
Click to collapse
Check this out:
Resco explorer
Pocket Mechanic
Pocket Toolman
Resco is very useful thing so the other two are very powerful as well. You will definetely uninstall S2U2 with more than one of them.
Good luck!
Hi, is it existing a French release of this rom for M88 or can you help me for translate it ? Cordialy
Sorry for my english very bad...
MMS works in this rom?
MMS works only with Arcsoft_MMS_Composer_v5.0.31.16
bye
Mark
i have aquestion... : I was screwing around with the m88 phone and put in the original rom in (I've done this many times) but this time i forgot to use the other three files .img and ... i only had the update.img in the card... then when i tried flahing it , it was reading but the battery fell out and now it wont turn on.... any ideas on how i can fix this... ???? I really need the help please!!! If it is possible to fix this.
helppp
I need help i was updating mi os , but it takes more than a half of hour , and now it wont turn on again how can i fix that? thanks?!
problems
i have a daxian +999
i flash it whit that file it work but now i have a white screen the phone looks like ok but nothing shows in the screen only a white screen what i can do ??
My touchscreen does work but I get the white screen asking me "updated from SD card?" then it just sits there. I dont have a keyboard to hit Y. None of the buttons do anything. Touching the screen does nothing.
*edit* figured it out. You just keep holding the power button down. Then it flashed to a solid purple screen. I went wtf.... it screwed up again? then after a few minutes it booted up.
problems in m89
hello, I recently bought a M89.
In general the phone is great, but mine has a very big problem.
As a PDA it works great, but when I insert my SIM card the phone just freezes. It works for just a minute after the SIM is inserted. I've even been able to make one or two calls before it freezes.
But past one or two minutes it just stops working. It doesn't respond to anything at all, the only solution is to remove the battery.
I think the problem is in the firmware. I've reinstalled a bunch of diferent firmwares: wm6 english, wm6.1 spanish, wm6 english again... and nothing works.
can anyone help me???, 'cause this is really killing me :'(
Thanks in advance!
oic0 said:
My touchscreen does work but I get the white screen asking me "updated from SD card?" then it just sits there. I dont have a keyboard to hit Y. None of the buttons do anything. Touching the screen does nothing.
*edit* figured it out. You just keep holding the power button down. Then it flashed to a solid purple screen. I went wtf.... it screwed up again? then after a few minutes it booted up.
Click to expand...
Click to collapse
Just wondering - What is the size of your microSD card.
As far as I know m88 does not support SD card greater that 4 Gb by default.
Please, let us know.
Updated from SD Card ?
Hello, first of all I want to say thank you because I learned a lot from this thread. I bought M88 phone some months ago and is the first time I cannot use ( I really don't know what went wrong but finally the phone is not working or frezze ).
I bought 2Gb card and was formatted in FAT32. I also complete all steps in order to load the original image but I got this message: "updated from SD card?" and nothing more... What button must be pressed ?
I'll go crazy... do you know what's the next step ?
Thank you very much.
i dont understand sorry. i have to copy the "update" imgfile and rename it as "uploader"... and leave this two files : "update and uploader" in the root folder ?
I've install ROM from this topic: http://forum.xda-developers.com/showthread.php?t=452848
and now, when I try power on my MiPhone - it show only white screen - please help!
bootloading
the file, atleast on windows 7, shows up as "update". Also, I found it works must faster and easier to make 3 copies (4 files total)
naming 1: update.img
2: uploader.img
3: Update
and 4: uploader
(so the last 2 don't actual have .img in the title)
Then just make sure you hold down both the buttons, and vuo-la! haha
Doesn't fix the MMS problem though.
Does anyone know how to make it so that it can use mms?
Miphon m88
Danke es funktioniert supper !!
i got white screen too ;[ how to fix my phone now ;/ i dont see enythink ;[
I would like to flash into 6.5 but the problem is i have a mac! I would really like to flash but i dont know if flashing from SD Card would work
Referring to this one:http://forum.xda-developers.com/showthread.php?t=336158
If there are other alternatives I would also like to know! Thanks in Advance....
Yes u can!!! .... next time try to do some SEARCH!!
Took it from here!!!
http://forum.xda-developers.com/showthread.php?t=293387&highlight=flash+sd
Format SD card using FAT32
1 Insert SD card into phone
2. Connect using ActiveSync
3. Rename nbh file to "EXCAIMG.nbh"
4. Copy EXCAIMG.nbh to SD card
5. Disconnect phone
6. Start Manual Bootloader (hold camera key for three seconds and press power button)
7. After quick messages (checking sd card, etc.) you should get "Update SD image? Press power button to download" screen with countdown in bottom corner
8. After timeout you will go to color bars UI
Exit bootloader: hold camera key, wait three seconds and hold down power key also until phone turns off
CacoPelao said:
Yes u can!!! .... next time try to do some SEARCH!!
Took it from here!!!
http://forum.xda-developers.com/showthread.php?t=293387&highlight=flash+sd
Format SD card using FAT32
1 Insert SD card into phone
2. Connect using ActiveSync
3. Rename nbh file to "EXCAIMG.nbh"
4. Copy EXCAIMG.nbh to SD card
5. Disconnect phone
6. Start Manual Bootloader (hold camera key for three seconds and press power button)
7. After quick messages (checking sd card, etc.) you should get "Update SD image? Press power button to download" screen with countdown in bottom corner
8. After timeout you will go to color bars UI
Exit bootloader: hold camera key, wait three seconds and hold down power key also until phone turns off
Click to expand...
Click to collapse
Thanks man, I've noticed you have a Claro logo below your nick. Did your excalibur came locked to Claro and with WM5 originally?? I was wondering if you know what original rom is the one for this phones?.
Thanks again
No it didn't, I have 2 Excaliburs, one is an HTC S620 no carrier and the other one an Unlocked tmo Dash. No Claro original ROM for the dominican Republic
cant seem to pass step 6!! wont work!!!!
it goes to the searching sd card but it only flashes for a sec then goes to the multicolor screen! iim so confused!
i have finnally got into the screenn and then it says
"invalid certificate"
What did i do wrong?
is your excalibur app unlocked??
Invalid Certificate message
I'm also getting this message, I have flashed previously (not from SD card) with no problem. I tried flashing through SD card since I'm dealing with a frozen screen that I can't fix due that I was trying to upgrade to the new WM 6.5 and I don't know if I locked again my device. I've tried everything posted on these forums to resurrect my excalibur and I'm running out of options. I can only get to the bootloader mode with no success with the original roms posted, my phone just throws me the "Invalid model error" or "invalid model vendor". Is there another way out?
you senior members&members should really lighten up on us rookies. it takes a little time to learn how to navigate the site. not everyone is an expert, including me, YET. there's alot of threads to go through. in the last week i've been here for hours doing research on how to do stuff. thought the idea was to HELP. be a little nicer, like Stylez who is very helpful.
crz6662 said:
you senior members&members should really lighten up on us rookies. it takes a little time to learn how to navigate the site. not everyone is an expert, including me, YET. there's alot of threads to go through. in the last week i've been here for hours doing research on how to do stuff. thought the idea was to HELP. be a little nicer, like Stylez who is very helpful.
Click to expand...
Click to collapse
it is not that they are trying to be up tight, or something like that....a lot of space gets occupied on the server by threads that need not be started.... search does a lot.... we all do want to help... but, I believe the old adage says that you cannot help someone who does not first help themselves... they are just trying to assure the rules be followed.....