dropped, power switch jammed in, need to disable. - P3300, MDA Compact III General

ae button maps power to another button, but because the power switch is locked in the unit wants to deep sleep. sucks
been searching for a way to unbind the power button, but failed.
i'm mediocre at tech stuff at best, looking for a registry tweak or such.
in fact i'm just plain looking for help!
been lurking on the boards for the last couple of years and appreciated all the work you guys have done for my xda's(made them usable for a start!)
taking this opportunity to say thank you.

Why are you going to resolve a hardware problem with a software tweak? If your power-button is broken, replace it! In the wiki section you´ll find a Service Manual on how to disable your device. Shouldn´t be that hard to replace a button. I mean your not going to change the CPU or so.....
regards
jabami

The Power Button consists od the plastic button which is held there by a springy membrane in turn held in 2 slots inside the case.
The button pushes the little switch on the Circuit Board - normally it's not touching it so that's being held in so the switch is always on and the phone won't behave properly.
Try a very thin blade to pop the button back up into place.
Otherwise it's a case off job which is not too difficult although you'll need a No 6 Torx screwdriver and sometype of plastic lever, very thin but strong to prise the case apart.
As stated follow the instructions but beware not all cases are the same so look carefully before you get mad at something......

thanks, that's exactly what I needed, especially the warning about the case difference
phone fixed and i'm happy.
note: the xda orbit doesn't have a seperate camera cover, the back is all one piece.
I didn't want to risk taking apart my satnav just before my xmas dash around the country, but then i remembered i could steal my wife's and i'm due an upgrade, so i went for it.
there will be a slightly foxed orbit going on ebay in jan, just after i receive my upgrade. now i have to decide whether i want the tytn ii or the polaris.......
choices, choices........
Thanks again, for the help.
Silver

Related

HELP ME!! Stylus end is stuck!

:? Boy do I feel dumb.
I've been using a 3-1 stylus (from Proporta) on my M2K and today the plastic "tip" got stuck in the unit's slot! Peering down the slot using a desk-lamp I can see the tip and it's off-centre to the actual axis of the hole. It looks like the hole for the stylus is NOT a tube - but is instead merely an opening into the unit. (thinking about it - I'd noticed that the stylus tip was "awkward" to fit into the slot a couple of times - obviously it had been getting caught in the body-work).
Stupidly I've further compounded my troubles by attempting to fineagle (technical term.. ) the tip out by using a biro refill - and the tip of the biro refill got stuck in the stylus tip!!! AAARGH! :shock:
Looks like I'll need to dismantle the entire bloody unit to get this thing out - so... how do I do it, what do I need, and where can I obtain the tools??
DOH!!!!
Damm, your having one of those day's
Just as a side note.
Don’t buy or use 3 in 1 stylus, they will break the clamp in the device holding the stylus in place so the stylus gets so loose that it will slide out and in without any resistance
Check your warranty before taking your unit apart!
You'll need a T6x60 and maybe a T7x60 drive. Then search for a thread on this forum that will guide you through the dismantling process.
good luck!
nomadman said:
Check your warranty before taking your unit apart!
You'll need a T6x60 and maybe a T7x60 drive. Then search for a thread on this forum that will guide you through the dismantling process.
good luck!
Click to expand...
Click to collapse
somehow I doubt Orange will be terribly impressed with what's hapened!!!
Anyone know how much it would cost to have the unit dismantled by a repair workshop (and thus maintain the warranty)? And is there such a place in central London?
Why not try the finest tad (more technical phraseology) of super glue on the end of your 3 in 1, push in hole, wait 1 minute and pull out. It might just work and surely would have done without that biro bit. Got to be worth a try - but be frugal with the glue !
By the way, I've used a 3 in 1 form Proporta for 3 months now and the old stylus fits and is retained just the same as its always has done (just tried it).
Stylus.
Hmmm I dont remember where i bought mine, but this is the second time i need to get the 9090 to service.
There is no resistense at all, it just slide in and out by it self
They are going right to the trashbin now.
Do you have a link to where you got yours??
Bottom stylus is the original.
Much more soft in the area where the clamp goes in
Mine came from here;
http://www.proporta.com/F02/PPF02P05.php?t_id=933&t_mode=des
But having looked at your photograph, and had a good look at my stylii, the 'shoulder' is different on my original stylus and that from Proporta - just as your picky shows. Still haven't had a problem though - YET.
Don't like it that you have to take of the tip to use the pen as reset tool
The ones i got are working very good, but I just cant use them any more since they destroy the clamp.
Here's one more pic.
I don't. I just use the tip of the stylus for re-set.
If you pull out the stylus and look into the hole in the BA, does it look like white plastic clamps in your BA.
I can se 2 white plastic clamps in mine.
Yes - just the same !
Since we both have plastic clamps, my stylus clamp shoulders must be the reason for the defect in the BA.
Well then I can only say to anybody reading this thread, don't buy 3 in 1 stylus that look like the ones in the pictures :!: :!:
TIP: Use a software to reset the PPC. I use CLaunch on normal reset. During lockups, I have to use the stylus. But that's only 1out of 10 resets.
http://home.pacific.net.sg/~welic/claunch.html
nomadman - sir, sorry this is out of the topic.... i just noticed your ROM version... where did you get the ROM update for our XDA IIs?
Thanks!
YAY! Fixed it last night.
1 T6 driver and 1 small flat bladed screwdriver were all the tools necessary.
Just removed the 2 silver screws, and 3 of the black ones (the "Void" sticker was untouched) and the rear cover was loose enough to allow the very flat blade of the screwdriver in just far enough to dislodge the "item" and it just dropped out.
reassembly was easy and the only shock I got was when I turned the unit back on the emergency battery was nearly dead!! I'd only had the main battery off the unit for 5 minutes!!!! Not terribly impressed by that I have to say.

Has anyone changed their housing on the Artemis?

I'm curious to know if you can get it back together with all the seems as tight as when it was new. I want to get a new case off ebay but I want to know if there's problems with if fitting together again after it's been disassembled.
I was able to do it. It came out pretty good but I did slightly bend the metal edge of the new frame when I had to reopen it to align the reset button cover. But it's so slight, no one would ever be able to tell but me. All in all, it wasn't too bad, but it was just nerve racking having your $500 phone ripped apart and wondering if it will work when you put it back together - if you can get it back together. I was so relieved when I got the WM screen again!
A few pieces of advice:
For one, the instructions I read just said to disconnect the ribbon cables. Well it doesn't say that all you have to do is flip up the little plastic part to release the tension from the ribbon. (figured that out the hard way)
Also, make sure the rubber covers for items like the mic and reset button line up before you resecure the board to the frame. You DON't want to have to reopen it.
My phone will now stay covered with an excellent silicone cover made by Boxwave. The cut-outs are precision - you can get to everything. Also, it fits nice and tight like a glove. And it's just thick enought to protect, fit in the carrying case, and allow you to use all the buttons easily, especially the scroll wheel. (my last cover was too thick to use it with the cover on) I don't want to have to do this surgery an my phone any time in the near future so this is staying on my phone.
Problem when change housing
Yesterday I've change my M700 housing with P800. But as we know, they have different button map.
Now, I am trying to set up a hotkey for the Call button (Green button),
ie, when I press the call button, an application of my choice would
start running. For that I need to change the default settings in the
registry of the Pocket Pc. Could someone tell me where the default
settings of the call button is stored in the registry and what all
values should I change in the registry so that I can setup the call
button hotkey. Any help would be highly appreciated.
Why not just download hbutton and map as many programs as you like to the other available buttons? I've got like 12 prog mapped to 5 buttons.
Edit: Oops. I missed the point of your post. The buttons are mapped differently.

Problem with trackball!

Hi guys,
The trackball on my Orbit has stopped recognising being rolled up, left or right, and the silver clickwheel is stiff. Is this repairable myself, or should I be looking at a new motherboard?
Cheers,
Nick
hey dontpannic, don't panic
at least not too hard.
It is possible to exchange the trackball unit. You can sell a new one on the internet (I bought one via eBay, it was in your country and very cheap) Allthough, it is kind of hard to get the old unit out of your phone. You will have to totally apart your phone, because the trackball unit is stick to the daughterboard which is behind the LCD
There are a number of guides to help you apart your phone, you can find it somewhere on this forum. Once apart, you can blow the dust out and uncover your current trackball (mine was kind of hidden ) Or you can get the whole trackball off the board and replace it.
(I should note I got my phone apart couple of times, so have some experience. It can be tricky)
ciao!
I agree with amfasis, it can be tricky but gets very easy once you've done it a couple of times and know what to expect (how much force to apply separating parts...)
Everything on the daughterboard is pretty open under the cover so I suspect something sticky got dripped in there (cola?) from the symptoms you mention.
I thought I had a problem with my daughterboard as well since I was getting random scrolling action in all applications, but it turned out I had some dirt stuck on the side of the screen giving a bad signal on the touchscreen.
I took apart my whole trackball and even took the silver cover off the silver scroll wheel toggle and took out the tiny spring... that was an adventure getting it all back together correctly after cleaning!
I chalk all of it up to an excellent learning experience and now have no fear of taking it all apart just to look at it again. You will too.
Good luck!
Thanks guys! Will give this a try and see what happens

Hardware problem (buttons), please help.

over the past few weeks some of the buttons (namely left soft key, up and left) have stopped working, i've tried numerous roms just incase but it's definatley a hardware issue, now, i've dismanted the phone using the diamantos guide to see if anything jumps out at me, gave the phone a damn good cleaning whilst i had the chance, put it back together....but nothing, everything seems to be in order, all components in their rightful place but i still cant work it out, does anyone know if this is a common problem or if theres a fix as i've been unsuccessful in my searches.
actually, i just found the solution and it worked a treat, thanks anyway people.
btw, if anyone would like to know what i did then i'll be more than happy to share the solution.
godofwap said:
actually, i just found the solution and it worked a treat, thanks anyway people.
btw, if anyone would like to know what i did then i'll be more than happy to share the solution.
Click to expand...
Click to collapse
I'll be more than happy
please share your solution with us, I have the exact same problem
ok, no problem, heres what i did.
before you start please be aware that this is a very delicate procedure and you should take care as this may naff up your beloved trinity.
ok, i first disassembled my trinity using the dimantos guide located here http://forum.xda-developers.com/showthread.php?t=311463,
now, when you get to the keyboard / button pcb take it out if, you look closely you'll notice theres a thin adhesive plastic cover covering the metalic buttons, very very carefull peel this back (i used a sharp knife to get to it), making sure not to completely remove it, try to only expose the underneath of the buttons in question, you'll see that the buttons come away with the plasic leaving the underneath exposed, now, using a cotton bud and some lightly applied alcohol clean the contacts then when all is done, replace the plastic and make sure its firmly pressed back down you may notice it making a different, kind of sharper clicking noise when depressed than before meaning its worked, repeat for all buttons.
i think whats going on here is the gum or glue from the plastic film has "leaked" if you will, onto the plates meaning theres no contact from the buttons, this would also account for the very slight change in sound when you now press the button.
i found this info here http://forum.xda-developers.com/archive/index.php/t-289737.html
i have the same problem with the front hardware keys. They last around 1 year, i had them changed under warranty the first time but now they are failing again.
Thank you! now i just have check for tools and some courage because i fear damaging my good old trinity.
temp9300 said:
i have the same problem with the front hardware keys. They last around 1 year, i had them changed under warranty the first time but now they are failing again.
Thank you! now i just have check for tools and some courage because i fear damaging my good old trinity.
Click to expand...
Click to collapse
....hi to all dear friends!!after half an year of very hard work my trinity has the same problem....only central botton working but,the superior two,works if I do an hard reset!very strange!changing a lot of different roms,from w 5 to w 6.5 the problems doesn't solve...!
- I'd like to make your same operation but I'd like to know first if you too have they working on hard reset before trying....
thanks a lot and merry christmas!
yes, even after a hard reset they work for me, its as if it was brand new, bare in mind you may have a different problem so if your gonna try this, TAKE YOUR TIME.
godofwap said:
now, when you get to the keyboard / button pcb take it out if, you look closely you'll notice theres a thin adhesive plastic cover covering the metalic buttons, very very carefull peel this back (i used a sharp knife to get to it), making sure not to completely remove it, try to only expose the underneath of the buttons in question, you'll see that the buttons come away with the plasic leaving the underneath exposed, now, using a cotton bud and some lightly applied alcohol clean the contacts then
Click to expand...
Click to collapse
I tried doing this but found no plastic cover above the metallic buttons. Maybe it's because mine went for repair with this problem before, dunno.
I don't think i can mess with the metallic part so i guess i'm stuck with this unless i buy a new keyboard.
it's more of a very very thin laminate, like sticky back plastic than a cover, it should definately be there unless they replaced the PCB with a different model, otherwise the metalic buttons would just fall away. Again, they may have used a different version of the PCB. You can actually buy the PCB and replace it yourself. (here http://cnn.cn/shop/p3600dopod-d810-keypad-p-1825.html )

Volume Button broke on 3 week old tilt2!?

So i go my device about 3 weeks ago. last night i noticed the volume down button wasn't working, so i took off the battery cover and this is what i've found.
Theres a plastic piece that goes over the button and looks like the one for volume down as slid into the device, the volume up & PTT button's plastic cover looks to be going loose as well.. :/
I know i can take it into the device support center but they'll probably give me a refurbished device which i dont want. I payed for a new device, its fairly new and i should get a new device!
Anyone else experienced this?
ouch. it looks like your other buttons are a little broken too. how hard are you pressing those? ive had my tilt 2 for a month and a half and the buttons are still perfectly aligned and feel brand new.
Looking at my case and the vol/ptt buttons inside it doesn't even look like it'd be possible to push hard enough on the outside to cause that. However all three buttons do have the same internal plastic piece which is probably why the other buttons are going.
If you're under 30 days can't you return the device? I thought AT&T had a 30 day return period.
My volume buttons didn't break off like yours, but they did lose tactile feedback after a while. That is, when I press it, it doesn't click and bounce back as strong as before. They felt dull when I press them.
So what I did was put layers of scotch tape against the inside of the back cover where it would come in contact with the volume buttons. (Not sure if I explained it properly). Now my buttons work beautifully again.
If others are having this problem, please let me know. I can post some pics so that you can try.
ohyeahar said:
My volume buttons didn't break off like yours, but they did lose tactile feedback after a while. That is, when I press it, it doesn't click and bounce back as strong as before. They felt dull when I press them.
So what I did was put layers of scotch tape against the inside of the back cover where it would come in contact with the volume buttons. (Not sure if I explained it properly). Now my buttons work beautifully again.
If others are having this problem, please let me know. I can post some pics so that you can try.
Click to expand...
Click to collapse
I'm having that with mine right now actually, just started noticing it in the past week. I'll give your trick a shot, thanks!
so i got pretty drunk last night (almost like every night but thats a different story ) and i remember dropping my phone on the pavement. And just now i noticed the volume down button has fixed itself from the drop! haha
i tried manually moving the cover piece back over the button when it first broke and that didn't help. so i guess the solution is to drop your phone!

Categories

Resources