Related
Hi,
I just started with the ROM upgrade of my I-mate Pocket PC to 1.72.00wwe (obtained from the I-mate website) when my phone switched off. Now it only has (at the top) "Serial" and (at the bottom) "v1.06". No matter what I do - soft or hard reset nothing happens, obviously the power button also doesn't function. On my PC desktop I got the message that I need to reset my phone and re-connect.... can't get my phone going, so here I am.
The solution to my problem is (hopefully) simple ? I will really appreciate if you could help me with this ?
not a problem hopefully....u just made HimaClearJumpCode.exe run on ur device(this file exists in ur upgrade folder),and now ur stuck in the bootloader mode....
do the following:
1-hard reset ur device(it wont boot,off course)...
2-put it in the cradle,u should see that ur XP has found a new hardware(if it doesn't,change the USB port)
3-now run the himaupgradeUt.exe.
Now in case(just in case),those procedures didn't work,go to plan B.. :wink:
1-take the battery off ur Himalaya.
2-leave ur device for 12hours(it won't need all that time,but to be on the safe side,u know... :wink: ) without battery,so that backup battery drains...
3-put back the battery,recharge and enter the OS(this option wont work if u have erased the ROM)
4-rerun the upgrade...
good luck.....
RAGO :lol:
Hi
OK, what happens if the ROM is erased.... (judging by the fact that nothing happens when I put it in the cradle - with power on the cradle) ?
My phone was off for about 12-hours - blank screen when I got here this morning.
If I put it in the cradle (and after changing between all the available USB ports on my PC) the PC doesn't detect it - ActiveSync doesn't connect to the phone at all... Note : I have power on the cradle, and it's been a hour now - still just "USB" "v1.06" (or "Serial" if I take it out of the cradle).
:?:
so it is connected!!!!!!!!
since ur serial on the top of ur screen changes to USB when u put it in cradle,then it's connected.... :wink:
now just run the HimaUpgradeUt.exe in the folder that contains the NK.nbf file(32MB,it's the ROM),and it should start the upgrade....
be sure the NK.nbf is a Himalaya ROM....
good luck...
RAGO :lol:
Hi,
Thanks, did it just after posting my reply and everything worked out fine. Note, I just ran the ROM upgrade file (not HimaUpgradeUT), which I got from the clubimate webste.
Thanks, once again for helping me with this one.
Himalaya pocket pc - screen frozen on bootloader
Hi,
My problem is the same - but the difference is that whenever i run the himaupgradeut i get a connection error saying that the PC cannot identify the cradle as connected.
What should I do now?
I tried the Upgrade, but it did never start, so when I tried to get it back to normal, doing a reset, I only get the Bootloader screen, with the USB and v0.60, I tried a Soft and Hard Reset but nonthing, I have tired to re-flash it again, but also nothing, please any help, thanks
I can not even to start the Flash program, I get ERROR : 101
ERROR 101 : CONNECTION ERROR
PLEASE ANY ADVICE IS WELCOME, THANKS
I WAS ABLE TO REFLASH IT, BUT I STILL GET TO BOOTLOADER ONLY
PLEASE HELP
latest ActiveSync installed? Removed battery?
Had this issue Yesterday. Even if You update the ROM, You will still stay in bootloader (for me it was like this). Do another update, this time only the radio (so delete ms_.nbf and nk.nbf from the directory from where You run your upgrade utility). After this (another 20 minutes) You should be able to have result after the cold-reset.
On the bootloader there is a small difference. Upgrading the ROM shows how far he actually is (in percentage), whilst upgrading Radio it does not show You the percentage, only that he is busy.
Ruud
Just try the update without any insert card (sd and sim), and a wonder will happen!
Teja
- connect the JASJAR with your PC using the USB cable. Activesync will NOT start and the XP says does recognize it
- do a HardReset (press the 2 (-) in the keyboard and softrest it all at the same time. Hardreset screen appears (DON'T press 0 or X..)
- start the update program. Please use a good upgrade like the latest from imate ftp://ftp.clubimate.com/JASJAR_WWE_11353_137_10301.zip
- start the update and when it's looking to check the version of the JASJAR softreset it
It should start to reflash it without problems.
I hope it helps...
Hi there!
What key combination gets me into the bootloader?
I've been wondering and searching for a way to upgrade my MDA pro rom. (searching for hours on xda, google and a lot of other specialized sites. Turned out to be dead ends! FRUSTRATING!
I'va had a Qtek S100 before. There was a way to get into the bootloader. And there is a way into the bootloader for the Universal to! YES!
But when i try to push the buttons
on/of
Camera
reset button
i cant get in!
button 1 and 2
reset
the same problem.
I get as far as the pres 0 or X for factory default and exit.
Who can help me? I have the no_id upgrade utility and the ROM ready.
Was there a UUL file which i had to edit before using this upgrade method?
I hope there wil be a good tutorial for this just like the one i have used to upgrade my S100 to an orange rom. (worked great!)
Can anyone help me please
Its BACKLIGHT BUTTON + POWER BUTTON + RESET HOLE
It's better to do this without the SIM and Memory Card connected. Disconnect also the USB Sync Cable.
After entering bootloader, you will see SERIAL written on the screen but the screen has no backlight so you have to look hard.
Then when you plug the Sync Cable, the SERIAL will change to USB then you can run the NoID to update.
Remember the NoID has to be run twice in a row as the first time usually solicits an ID Country error
It Works
Thanks Jorge!
Just those keystrokes helped me a lot. It works just fine and it took me only one run to Initiate the upgrading.
Thanks a lot!
I followed your advice and removed the SD and the phone card.
Yes! now i can experiment with these ROMS.
First Jasjar, later O2 and hoping for the best roms with the best programs.(hoping to find a messenger cab file in the jasjar rom)
As I am planning to do the same, Try all the variants of the ROM's, could you inform me what are the good and bad points of all the different ROM's you used and which did you decide to use finally.
Thanks
HELP !!!!
I turn on my Qtek 9000 and i see SERIAL written and the screen but the screen has no backlight.
How can I boot my Qtek 9000 again without this SERIAL mode ????
Best Regards
Hi Ecraseur,
if You did not do anything else (no upgrading), try ColdReset : Power-switch + Reset hole.
Ruud
If we can boot from Serial/USB is it possible to boot from Mini SD? I'm toying with the idea that by using a Linux Live Disk content on a Mini SD it may be possible to boot into a virtual Linux environment? I know it's going to be uber slow and may not even work but I thought it may be worth a look?
If a Mini SD boot isn't possible do you think it'd work to have one of the smaller USB bootable Linux flavours as the USB boot for the HTC Wizard etc?
Hi, a friend have 2 pda universal from vodafone that he has flashed and killed. I don´t know what happend. pda always shows USB and v1.00. After a lots o rom updates still dead, i have JAFWM, but with or without this machine is dead.
any rom especial version?
any soft?
thanks.
1. Try to restart the device in bootloader mode(Light key, power and reset pressed together)
2. Look at the display (should say Serial and version at the bottom)
3. Disable the USB connection in Active Sync otherwise the update will crash.
4. Plug in USB Cable (Screen Should now show USB at the top)
5. Start original Upgrade from your provider or take the upgrade you want to use with the MA_UpGrade_noid.exe.
6. After Flashing restart device with both soft keys at the bottom of the screen ( Buttons with - on it) pressed.
7. When asked type 0 to erase all data.
9. Device should start normally, if it doesn't do not hesitate to ask.
device always start in bootloader mode, i flash all times without problems, but when i restart device, automatically puts on bootloader mode.
after flash, make factory settings but,after this, restart in same mode.
always, when i run update program soft MaUpgradeUt_noID, detects no rom in pocket loaded.
strange problem on 2 pda´s ?
thanks
That shouldn't be a problem. Just continue to flash the rom. There could be a problem with your bootloader and the upgrade version (AKU2) you want to use.
Maybe it's a problem with bootloader.
Try it, maybe it will help you.
http://forum.xda-developers.com/download.php?id=11414
i think same as you, only problem with ROM image, but i have flashed many roms but I can´t revive device. So i ask name of Rom tht can revive pda.
Br.
PD. how i can flash the archive attached?
The rar file mentioned above is only the bootloader you already got on your device.
In your case i would use an old AKU1 rom and to see if it works.
hi guys
i have same problem. show only boot loader mode. how to use this boot loader file. wich AKU1 file is working. my phone is MDA PRO from germany T-mobile, i wan't to update ro to English. after flashing many times, many rom no result. help me
thanks a lot
Hello Siemens Man
Which Bootloader do you have ?
It would be great if you could make an backup of your bootloader then, that i could downgrade my phone and try to unlock it.(If do not know how to make an backup, thats no problem, because i can show you how to do it)
greetz
hi man
i have in boot loader mode. show me usb v1.00 only. i don't have buck up for my phone. please tell me solution how repair my phone.
thanks a lot
Did you try to update your phone to the latest orange rom for testing yet ?
If not try it out (I know it is said to be slow, but only if all orange customizations are installed) If it runs then its ok.
Otherwise try to use the exitbl.exe mentioned somewhere in this forum, hopefully it works.
connect to mtty and issue set 14 0 and then restart the device or use exitbl utility by buzz
hi guys
thank you for reply mail. all problem solved. now good working
thanks to Buzz
are there any useful hints extrem69 ?
no usb mode
What can i do of my Qtek 9000 doesen't change from Serial to USB mode?
siemens man said:
hi guys
thank you for reply mail. all problem solved. now good working
thanks to Buzz
Click to expand...
Click to collapse
I had same problem like you, can you tell me what exactly did you do so you can repaire your phone.
I used T-mobie and didn't work after upgrade rom too, it's alway stop in boot loader screen. I tried up rom of T-mobile, Imate, Dopod but nothing to work, I don't know how to repair it, it's still can up rom normaly, nothing wrong while upgrade, it's only don't work after finish.
wooooooooooooooooooow
many thanks
i tried many ways to solve this problem
with your advuse it is working now.................
Lt.Cmdr.Ivan said:
1. Try to restart the device in bootloader mode(Light key, power and reset pressed together)
2. Look at the display (should say Serial and version at the bottom)
3. Disable the USB connection in Active Sync otherwise the update will crash.
4. Plug in USB Cable (Screen Should now show USB at the top)
5. Start original Upgrade from your provider or take the upgrade you want to use with the MA_UpGrade_noid.exe.
6. After Flashing restart device with both soft keys at the bottom of the screen ( Buttons with - on it) pressed.
7. When asked type 0 to erase all data.
9. Device should start normally, if it doesn't do not hesitate to ask.
Click to expand...
Click to collapse
HI to all! I have lost bootloader upgrading my qtek 9000 vodafone.
can i to solve problem? No bootloader menu, i have tried power+reset+lamp, power+reset+camera - herd reset with - + - reset without effect. Pse help me!!! Thanks.
Hi guys.
I was using the installed the FInixNOver 3.0.1 ROM onto my SPV M700 and it was great. I've had it for about 2 weeks without any problems.
Last night I looked at my phone, only to realise that it was completley dead. This didnt shock me to much because the battery was running low, and i decided to let it die completley before recharging it again.
I charged my phone overnight and switched it on this morning, but the phone would freeze at the 'FInixNOver' splash screen (the numbers at the bottom of the screen would appear overlaying the splash, but the phone wouldnt go pass this point).
The only way to turn off the phone from this state is to eject the battery. I have tried removing the sim card, turning it back on in as many ways as possible but to no avail. I am able to get to the TriColor test screen (im running IPL-0.50 / SPL-1.30.Olipro) but with all the custom roms available, they all use the ROMUpdateUtility which requires the phone to have established an activesync connection initially (but this would mean my phone would have to be 'on completley' - so this is catch 22.)
For the record, my phone/battery died while my wired handsfree was attached (dunno if thats of any interest to anyone or the rom baker).
But it looks like the only way i'll be able to flash my phone is by finding a way to install the .nbh file without using the RUU method. Because I can put my phone into test mode manually.... any help or guidence would be very much appriciated.
Thanks.
Ok can you get it into bootloader? power/camera buttons and reset?
sorry didnt read fully.
right get your device into bootloader first,
then open active sync (are you using xp)
then open connection settings and disable usb connection,
put your device into bootloader mode, then run any rom upgrade, i prefer the WM6.1 pdaviets from HERE (Username: PDAVIET / Password: pdaviet)
Your pda does not need active sync with ruu's, so no catch 22. if you turn off usb connection in active sync, you can still run ruu and it will be recognised, unless you are using vista, where you need to change your HTC SYNC drivers.
Thanks for your quick response...
Yes I can get into boot loader using the power and camera buttons (or holding the power and camera buttons when resetting the phone)...
When the phone is in boot loader mode, active sync doesnt even detect the phone anyway, but nevertheless, I have followed your instructions and disabled the USB Connection. (BTW, yes i am using XP)
The phone is still in boot loader mode, so now i try and execute the ROMUpdateUtility.exe and go through the steps, at the 1st step i tick the tickbox and click next, and the 2nd step i tick the tickbox and click next. (this step says DO NOT enter the bootloader manually? - but i have havent i?) anyway, when i click next, it says... "Verifying the information on your Trinity... Please Wait..." for about 10 seconds, and then i get a message "ERROR [260] : CONNECTION"
What am i doing wrong?
Huumm.. why dont you flash your phone throw the sd card??
Read this link:
http://wiki.xda-developers.com/index.php?pagename=Trinity_SDCardFlashing
try to flash your phone with some official rom and after that flash it with any other you want!
manos_23 said:
try to flash your phone with some official rom and after that flash it with any other you want!
Click to expand...
Click to collapse
I would recommend this option above, to be safe, i usually get them error messages when the battery is below 50% or sometimes i try it again and it works. it does state do not manually enter bootloader but i always do it this way.
also make sure active sync is not still running in taskmanager under the alais: wcescomm.exe and WCESMGR.exe, end them both.
I've just tried using an official ROM, but the problem still occurs with the 'connecting'. It doesnt seem that the computer picks up a connection to the phone whatsoever.
Should i be concerned that at the bottom of the bootloader screen it says "serial", is this correct?
Im starting to get annoyed now.
Bye,
the bottom of the sreen mast say "usb" not serial.
it seems there is a problem, if it states serial. as it should say usb. try THIS
Seems like the problem was that my USB lead was loose and made a bad connection, hence why the bootloader showed 'serial' and not 'usb'... as soon as i wiggled it and heard the 'connection noise' in windows, i knew i was good to go, and so using the RUU worked fine to reupdate my phones ROM.
Thanks for your help.
My only question is that why did it happen in the first plave?
WIZZKID - I just saw your post here now. I have to tell you that I also saw "SERIAL" at the bottom of the bootloader screen and not "USB". As I said I returned it to get another phone but maybe I will try something else for now instead of a P3600i. I will monitor your thread to see how it turns out for your phone, because it seems that we have the same problem.
if you see "serial" instead "usb" your problem is in the usb cable, usb port from your computer or in the usb connector from your trinity!!!!!
I was having the same problem that you have!! my problem was from my usb from mine trinity!! see if the conector is at good conditions !!!
Well as some of you may know, I got my Trinity replaced for sticking at the WM splash screen after a few days. This second one - I have had it ONE night - and the same thing has happened with incomplete booting. This time I have been trying all night to flash the phone to an official ROM, but I cannot do it (apparently) because I can't establish a connection via ActiveSync. When I stick the data cable in while in bootloader I see SERIAL replaced by USB and when I try the flash I get a "270" error (cannot connect to phone) and the phone re-boots to the sticking plash screen. What should I do now?
ladies and gentlemen...
we've got a lot of mixed messages in this thread.. please make sure you're posting the right thing. no need to disable USB when manually going in to bootloader to flash (at least in xp).. Also, you can ignore the part of the RUU that says 'do not manually enter bootloader' (you should really read the guide on my site)
foxuniform- can you please give some details..
1) are you running xp or vista
2) have you flashed hard-spl? if so what version?
in the mean time, try a couple of things.. first, flash hard-spl (even if you already have it, but from the sound of it i think you don't have it on your device).. if that works, try to flash an official ROM. Can also try to use splxploit, then flash hard-spl, and then flash official ROM (there's a guide on my site if you're unsure)
please post your results
*edit*
here are the steps for SD card upgrade, but i HIGHLY recommend flashing Hard-spl first..
try to do it from SD card. how?
Extract the .NBH file from your prefered ROM upgrade: In windows use winrar (right click) to extract the contents of the exe file. In Linux / MacOS use cabextract (http://www.cabextract.org.uk/) .
Rename the .NBH file to TRINIMG.nbh and copy it to the root folder of your miniSD card.
With miniSD card inserted on the phone, start the bootloader (hold Power button on right side and Camera button at same time and stick with stylus in RESET on bottom).
You should see the screen pictured on the left, confirm flashing on screen by pressing the power button.
Flashing might hang after some time but this is normal. Just wait. Complete flash takes about 30 minutes, so check your battery or connect to charger before the flashing process starts.
When flashing completes soft-reset your device.
Make sure your SD has FAT32 and has no label. There have been reports that if SD has a label the bootloader can not access the TRINIMG.nbh
racerx_ I have carefully read your response and suggestions, and thanks for your expertise input on the matter. I am fairly new to this stuff so read below carefully as you may find errors in the way I tried to go about doing what I was hoping to accomplish.
First let me answer your questions. I am running Windows XP. The phone is in it's completely natural state in that I have not flashed it in any way. The ROM I was TRYING to flash to the phone while it was not starting properly (this is where I manually entered bootloader) is an official ROM from the HTC website (please note everyone that when I registered my P3600i on the HTC website it came up as the Dopod 810). Anyway, that never worked. ActiveSync never detected the phone (and I guess that's the reason I could not do anything as far as flashing goes). I HARD-RESET my P3600i and it booted normally. I re-installed all the stuff I had on it, from memory card to various .cab files, and the phone is working beautifully thus far. I will report if anything funny happens again.
I have to ask you racerx_, if I CAN flash hard-SPL on the P3600i according to the lovely guide on www.trinityguides.info. I have been of the opinion that things don't work for the P3600i as they did for the P3600, and that has been echoed by many P3600i users on this forum who are ready and waiting to try out some cooked ROMs (myself included).
For the sake of record, my phone is running rom version 3.00.707.17 and radio version 1.46.00.11. I patiently await your response.
woaaahhh..
i didn't notice the 'i' in your previous post... yeah, as far as i know, these ROMs are not flashable on your p3600i.. sorry..
**correct me if i'm wrong somebody**
Yeah I kinda thought that would be your response. By the way - do you think that this phenomenon of sticking at the Windows Mobile splash screen (both the P3600 and P3600i models apparently) has anything to do with something users do with the devices, or you figure it's an inherent software glitch of some sort? I am wondering if I should try a different model or hold on to my P3600i? Hope it's not something that'll happen again - I fly for a living and it's not gonna be good to have the thing screw up on me away from base - I really count on it for everything from casual keeping in touch on Messenger to viewing my work schedule. I love the Trinity though - it's one of my all-time favourite HTC phones.
hmm... i don't think its inherent in the Trinity.. (not a hardware issue.. in my opinion)
its been a while since i followed the posts on it, but always seems to be software related.. sometimes ROM-specific problem. Personally, i've probably flashed as many ROMs as anyone and the only time i ever encountered problems was with the official HTC WM6 ha.. go figure.. I think ppl did find that hard resets before and after flashing are helpful as well..
i love my trinity, and there's not much else on the market to make me want to trade it in (is it just me, or have pda's kind of stopped getting cooler).. i'd stick with it..