can't seem to get this upgrade to work. the updater stops at about 28 percent for me with an error (286? i think) and after that i'm stuck in bootloader. Every time after that, the updater wont even start.. (a different error).
i can flash successfully a cooked ROM, but can't get the official one to work. Could it be a conflict with Des' crash-proof SPL? That's the only thing i can think of at this point..
To me said invalid device id, and got stuck on the boot loader
try back to any old offical ROM
and then copy SSPL to PDA and run it on PDA
when bootloader appear, run WM6 offical updater
I got same problem too and get fix
good luck
update: since i managed to flash PDAVIET's rom, i thought i'd just try going back to Olipro's hard-spl and see what happens.. So i flashed it, entered bootloader and ran the WM6 update again, and SUCCESS!!
very strange though.. anyone have some thoughts as to why it wouldn't work under Des', or if this is just coincidence?
It installs a new bootloader that can't be hacked by the previous hacks I think.... I'm stuck in it too...
SPL-3.03.0000
racerx_ said:
update: since i managed to flash PDAVIET's rom, i thought i'd just try going back to Olipro's hard-spl and see what happens.. So i flashed it, entered bootloader and ran the WM6 update again, and SUCCESS!!
very strange though.. anyone have some thoughts as to why it wouldn't work under Des', or if this is just coincidence?
Click to expand...
Click to collapse
Hi racerx,
I've encountered the same problem as your, stuck at 28% ERROR [286] while flashing, and couldn't go over it even after recovery process following the instruction.
Could you please explain a bit more details about how to go back to Olipro's hard-spl and enter into bootloader?
Thanks, eager to flash the new ROM...
Well I was able to get out of it by running Pof's CID RUU Unlocker, however, it errors after 7%, and resets. It gets past the bootloader, however, it hardreset the phone...eh.
IT happened to me too - Update Error.
So should i go back to Official WM5 then update to WM6 (i had AX3L installed before and i just had to reflash back to AX3L coz of the error from WM6).
Kinda scared me.....LoL
well, to start with i had Des' Crash-Proof SPL on my phone... so after the updater hung at 28%, i remained in Des' bootloader. I then ran the RUU for pdaviet's ROM, which flashed successfully. After that was on and my trinity was up and running, i flashed Olipro's hard-spl. Then manually put it in bootloader again, and flashed the official ROM.
Let me say this, though. At this point, i think you should be content to get your device out of bootloader mode. This Dopod WM6 doesn't have so much to be desired in it compared to cooked ROM's on this forum, plus your bootloader will be stuck at version 3.xxxx which i don't know if anyone is sure how to deal with yet. I'm regretting flashing mine to official version. Should have waited for a chef to pack it up for me.
what does your bootloader say?
You need to actually have a device that this release is supported by. It flashes a new SPL but you can flash Olipros HARD SPL 1.20 straight over that once WM6 has flashed.
It replaces any HARD SPL before flashing, probably to ensure only official devices get this update. Those having issues are probably out of this.
The official rom is fine, not as finished or customised as some chef ones, but good none the less. Also, the new 3.0??? SPL is no issue at all and easily removed once flashed.
yeah saw your post on the other thread.. thanks for the tip! talk about a stressful morning haha..
i was waiting for this ROM cause my activesync has mysteriously stopped working for a couple of weeks. so i was going to flash and take it to the service center. The miracle of it, was after my device hung and i reflashed pdaviet's rom, my activesync mysteriously works now even though i reflashed a million times before trying to get it going haha..
new spl is needed for flashing new radio rom with cid locked device.
So that's why RUU reflashes SPL at first.
U could simply reflash HArd spl back by using sspl
mUn, when can we expect your much anticipated "Indigo" rom using this offical WM6 base??
Genius! thanks for the tip mun...
all i can say is one word....
INDIGOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO!!
I also got Invalid vendor ID when I tried to flash for the first time. But it flashed just fine after I put it into bootloader mode. Give it a try..
Flashed my mine in a breeze from LSVW version 27/05/07.
myppcsg said:
Flashed my mine in a breeze from LSVW version 27/05/07.
Click to expand...
Click to collapse
still same problem
can you post the RUU files plz
mxlaser said:
You need to actually have a device that this release is supported by. It flashes a new SPL but you can flash Olipros HARD SPL 1.20 straight over that once WM6 has flashed.
It replaces any HARD SPL before flashing, probably to ensure only official devices get this update. Those having issues are probably out of this.
The official rom is fine, not as finished or customised as some chef ones, but good none the less. Also, the new 3.0??? SPL is no issue at all and easily removed once flashed.
Click to expand...
Click to collapse
Thanks for all the helps from you guys. This is what I did after stuck at 28% with ERROR[286]:
1. Flash back to Official OZ WM5 ROM. Had no problem to flash back as it was in the bootload mode.
2. Flash Olipro's Hard-spl. No problem as well.
3. Flash Official OZ WM6 ROM again...... and stuck at 28% again!!!!!! with ERROR [262] @#[email protected]#$.
4. Now in the process flash back to Official WM5 again... @#@#@....
5. Will flash Official WM6 straightaway after that.
6. Will update result later....
geoffreyhan said:
Thanks for all the helps from you guys. This is what I did after stuck at 28% with ERROR[286]:
1. Flash back to Official OZ WM5 ROM. Had no problem to flash back as it was in the bootload mode.
2. Flash Olipro's Hard-spl. No problem as well.
3. Flash Official OZ WM6 ROM again...... and stuck at 28% again!!!!!! with ERROR [262] @#[email protected]#$.
4. Now in the process flash back to Official WM5 again... @#@#@....
5. Will flash Official WM6 straightaway after that.
6. Will update result later....
Click to expand...
Click to collapse
hehe i did that many time this day maybe hmmm 5 or 6 and im still doing that
try to use another version of RUU (the older one)
ps. plz don't post messages about indigo in other tgreads ) if u want to ask - so ask in mine thread.
I'll flash official rom today and then will make some conclusion ) but i thibk that indigo will be based on oficial release
Right, so I have 1.93 HardSPL installed from Olinex, but for some reason I can't update the ROM to the official HTC 2.03 release, it gets to 100% then shows a Upgrade Rom Error, Image File Corrupt, Please Try Again, message on the bootloader, I figured this might be becuase it needs the original 1.93 bootloader with it being a official release (unless I'm wrong) so I have got the stock 1.93 spl from the spl thread, I ran the update, it went straight to 100% and rebooted, still got Olinex's 1.93 on though.
Help.....
I have this problem too Gurus help please!
He-he, the problem is solved. To boot, you need a 1.09.25.23 radio.
hi guys
i would like to restore hard spl
when i bought diamond it has 1.93 wwe (rom) i dident remmer it hard spl
please help me to restore hard spl
thanx
i can restore it
this way
first i flashed it and install 1.93 wwe
then download this (1.93 and ruu) http://forum.xda-developers.com/showpost.php?p=2324829&postcount=39
then copy sspl manual on device and run ruu
So I have an HTC Touch Diamond GSM (DIAM 110)
I want to restore my phone to stock settings. I have done hard reset.
I have an issue where my phone hangs on the "touch diamond" screen. I can get into the boot loader and load (some) stock spls. (Others including stock HTC RUU give error)
When I load stock SPL, phone resets, but upon reset it shows OLINEX still.
What can I do???
i have the same problem
i can´t restore another SPL
i always see SPL - 1.40 OliNex
how can i replace it ?
thank´s a lot
Im having issues with SPL.
Originally, the device came with 1.93, so when I installed I installed hard spl 1.93 olinex.
Now I tried to do sim unlock and the guide asked me to go hspl 1.24, I tried to skip that step and go staright and install the patched radio, but it failed to update - error 226 with RUU.
I thought maybe its related to the hspl, so i downgraded to 1.24 but still I have that issue that I get error 226.
after i downgraded i still see in the bootloader mode spl 1.93 olinex.
I thought maybe to stock spl and then from there to hspl 1.24 and from there to patched radio maybe it will succed.
But even in stock spl it appears spl 1.93 olinex.
Also, besides that, i cant install the patched radio.
I appraciate your help..
Thanks.
I've noticed it the other way around, I first HardSPLed it with v1.40 and some later I flashed v1.93 (I think at least twice), without any error, but the flashscreen still says v1.40. Never had any problem though ...
Can't help you with the SIM unlocking, haven't tried it yet.
with the spl im mostly concerned because one day i might need warrenty and if it says 1.93.olinex..someone will probably suspect..
To Sim-unlock it doesn't matter you have HardSPL(Olinex) 1.40 or 1.93. The most important is your radio, you mut have the Diamond_Radio_1.00.25 intermediate to accept the SIM-unlock proces. Look at the thread .. unlock (sticky) and get the file - Radio downgrade - then you go. The error 226 is related to the radio version !!!
eranyanay said:
Im having issues with SPL.
Originally, the device came with 1.93, so when I installed I installed hard spl 1.93 olinex.
Now I tried to do sim unlock and the guide asked me to go hspl 1.24, I tried to skip that step and go staright and install the patched radio, but it failed to update - error 226 with RUU.
I thought maybe its related to the hspl, so i downgraded to 1.24 but still I have that issue that I get error 226.
after i downgraded i still see in the bootloader mode spl 1.93 olinex.
I thought maybe to stock spl and then from there to hspl 1.24 and from there to patched radio maybe it will succed.
But even in stock spl it appears spl 1.93 olinex.
Also, besides that, i cant install the patched radio.
I appraciate your help..
Thanks.
Click to expand...
Click to collapse
just flash this Spl : http://forum.xda-developers.com/showthread.php?t=400402 and then your problem is solved use the first zip download it worked with me
Hi!
I have some problem with the pda.
I have hspl on it. 1.93 Olinex, and a clear winmo 6.1 with no tf3d.
I just wanted to install this rom:
Gen.Y D2 R5.5[WM6.1 21056][UC][SENSE2.1][
http://forum.xda-developers.com/showthread.php?t=521941
In this thread they say this is the recommended radio rom for this rom:
"GSM Diamond Radio 1.13.25.24•RapidShare
•MegaUpload
•MediaFire
* This is an original Diamond Radio, no security unlock needed!"
ok. So I sarted the radio rom install with costumRUU. And when it gets to 100% the costumRUU stoped with rom flash error.
then later i find this thread:
http://forum.xda-developers.com/showthread.php?t=470306
this thrad says:
"Your phone has to be SECURITY UNLOCKED (WHICH IS NOT THE SAME AS SIM-UNLOCKED!!!)
Radio v1.13.25.24 (Blackstone) (SU) (Quad Band)(NEW) "
So. My pda wont start. when i start it, it goes to the booatloader screen and there is "rom flash error" text. And i cant reach the internal storage.
i ve tryed to install the stock rom but the instal stops at 13% with rom flash error 226.
i dont know what to do... can somebody help me?
Is the official rom same as the one you are able to download via the HTC official site using the serial number under the battery of your device...
Hi!
A few weeks ago the problem was the same. You tryed to help me, remember?
only the stock htc service could made it.
you gave me the link to my stock rom anno.
I cant flash the stock rom. Are there any rom with radio? Or just the stock rom has radio?