SPL Problem - Touch Diamond, MDA Compact IV ROM Development

Right, so I have 1.93 HardSPL installed from Olinex, but for some reason I can't update the ROM to the official HTC 2.03 release, it gets to 100% then shows a Upgrade Rom Error, Image File Corrupt, Please Try Again, message on the bootloader, I figured this might be becuase it needs the original 1.93 bootloader with it being a official release (unless I'm wrong) so I have got the stock 1.93 spl from the spl thread, I ran the update, it went straight to 100% and rebooted, still got Olinex's 1.93 on though.
Help.....

I have this problem too Gurus help please!

He-he, the problem is solved. To boot, you need a 1.09.25.23 radio.

Related

Trouble with Dopod WM6..

can't seem to get this upgrade to work. the updater stops at about 28 percent for me with an error (286? i think) and after that i'm stuck in bootloader. Every time after that, the updater wont even start.. (a different error).
i can flash successfully a cooked ROM, but can't get the official one to work. Could it be a conflict with Des' crash-proof SPL? That's the only thing i can think of at this point..
To me said invalid device id, and got stuck on the boot loader
try back to any old offical ROM
and then copy SSPL to PDA and run it on PDA
when bootloader appear, run WM6 offical updater
I got same problem too and get fix
good luck
update: since i managed to flash PDAVIET's rom, i thought i'd just try going back to Olipro's hard-spl and see what happens.. So i flashed it, entered bootloader and ran the WM6 update again, and SUCCESS!!
very strange though.. anyone have some thoughts as to why it wouldn't work under Des', or if this is just coincidence?
It installs a new bootloader that can't be hacked by the previous hacks I think.... I'm stuck in it too...
SPL-3.03.0000
racerx_ said:
update: since i managed to flash PDAVIET's rom, i thought i'd just try going back to Olipro's hard-spl and see what happens.. So i flashed it, entered bootloader and ran the WM6 update again, and SUCCESS!!
very strange though.. anyone have some thoughts as to why it wouldn't work under Des', or if this is just coincidence?
Click to expand...
Click to collapse
Hi racerx,
I've encountered the same problem as your, stuck at 28% ERROR [286] while flashing, and couldn't go over it even after recovery process following the instruction.
Could you please explain a bit more details about how to go back to Olipro's hard-spl and enter into bootloader?
Thanks, eager to flash the new ROM...
Well I was able to get out of it by running Pof's CID RUU Unlocker, however, it errors after 7%, and resets. It gets past the bootloader, however, it hardreset the phone...eh.
IT happened to me too - Update Error.
So should i go back to Official WM5 then update to WM6 (i had AX3L installed before and i just had to reflash back to AX3L coz of the error from WM6).
Kinda scared me.....LoL
well, to start with i had Des' Crash-Proof SPL on my phone... so after the updater hung at 28%, i remained in Des' bootloader. I then ran the RUU for pdaviet's ROM, which flashed successfully. After that was on and my trinity was up and running, i flashed Olipro's hard-spl. Then manually put it in bootloader again, and flashed the official ROM.
Let me say this, though. At this point, i think you should be content to get your device out of bootloader mode. This Dopod WM6 doesn't have so much to be desired in it compared to cooked ROM's on this forum, plus your bootloader will be stuck at version 3.xxxx which i don't know if anyone is sure how to deal with yet. I'm regretting flashing mine to official version. Should have waited for a chef to pack it up for me.
what does your bootloader say?
You need to actually have a device that this release is supported by. It flashes a new SPL but you can flash Olipros HARD SPL 1.20 straight over that once WM6 has flashed.
It replaces any HARD SPL before flashing, probably to ensure only official devices get this update. Those having issues are probably out of this.
The official rom is fine, not as finished or customised as some chef ones, but good none the less. Also, the new 3.0??? SPL is no issue at all and easily removed once flashed.
yeah saw your post on the other thread.. thanks for the tip! talk about a stressful morning haha..
i was waiting for this ROM cause my activesync has mysteriously stopped working for a couple of weeks. so i was going to flash and take it to the service center. The miracle of it, was after my device hung and i reflashed pdaviet's rom, my activesync mysteriously works now even though i reflashed a million times before trying to get it going haha..
new spl is needed for flashing new radio rom with cid locked device.
So that's why RUU reflashes SPL at first.
U could simply reflash HArd spl back by using sspl
mUn, when can we expect your much anticipated "Indigo" rom using this offical WM6 base??
Genius! thanks for the tip mun...
all i can say is one word....
INDIGOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO!!
I also got Invalid vendor ID when I tried to flash for the first time. But it flashed just fine after I put it into bootloader mode. Give it a try..
Flashed my mine in a breeze from LSVW version 27/05/07.
myppcsg said:
Flashed my mine in a breeze from LSVW version 27/05/07.
Click to expand...
Click to collapse
still same problem
can you post the RUU files plz
mxlaser said:
You need to actually have a device that this release is supported by. It flashes a new SPL but you can flash Olipros HARD SPL 1.20 straight over that once WM6 has flashed.
It replaces any HARD SPL before flashing, probably to ensure only official devices get this update. Those having issues are probably out of this.
The official rom is fine, not as finished or customised as some chef ones, but good none the less. Also, the new 3.0??? SPL is no issue at all and easily removed once flashed.
Click to expand...
Click to collapse
Thanks for all the helps from you guys. This is what I did after stuck at 28% with ERROR[286]:
1. Flash back to Official OZ WM5 ROM. Had no problem to flash back as it was in the bootload mode.
2. Flash Olipro's Hard-spl. No problem as well.
3. Flash Official OZ WM6 ROM again...... and stuck at 28% again!!!!!! with ERROR [262] @#[email protected]#$.
4. Now in the process flash back to Official WM5 again... @#@#@....
5. Will flash Official WM6 straightaway after that.
6. Will update result later....
geoffreyhan said:
Thanks for all the helps from you guys. This is what I did after stuck at 28% with ERROR[286]:
1. Flash back to Official OZ WM5 ROM. Had no problem to flash back as it was in the bootload mode.
2. Flash Olipro's Hard-spl. No problem as well.
3. Flash Official OZ WM6 ROM again...... and stuck at 28% again!!!!!! with ERROR [262] @#[email protected]#$.
4. Now in the process flash back to Official WM5 again... @#@#@....
5. Will flash Official WM6 straightaway after that.
6. Will update result later....
Click to expand...
Click to collapse
hehe i did that many time this day maybe hmmm 5 or 6 and im still doing that
try to use another version of RUU (the older one)
ps. plz don't post messages about indigo in other tgreads ) if u want to ask - so ask in mine thread.
I'll flash official rom today and then will make some conclusion ) but i thibk that indigo will be based on oficial release

SPL 2.03 Problems

Hi,
I recently had my diamond return to me from HTC (screen repair) and as part of the normal process they flash the latest rom when they return the device.
Now i have the latest 2.03 rom and 2.03 SPL (did not know there was a 2.03 SPL)
Now for the problem..... I cant seem to flash to a hard SPL ie 1.24 or 1.40, i have tried them all and i have tried the manual method (no luck).
Prior to me sending off my diamond i had flashed the 1.24 spl with no issues.
I have looked all over the forum and i can't find any mention of a 2.03 SPL and i am wondering is this new SPL prevents you from flashing to any older/other SPL versions.
If any one has any ideas please help.
_)_?_:?
problems because of the SPL?
There is a good part to the new SPL?
could someone get this SPL? for a separate installation?
thanks :d
Yeah it is strange i had no idea there was a new one until i tried to flash and it shows spl 2.03 on the boot loader screen.
If someone knows how i can get a copy of this SPL off my device i will post it for all to look at.
bump...Loads of people have looked at this, no one with any ideas ??
if i remember corectly i had it on my phone also, but i could change it...
littlej said:
if i remember corectly i had it on my phone also, but i could change it...
Click to expand...
Click to collapse
ahhh interesting..... which SPL do you now have on your diamond ?
You have to use SSPL.
Just flashed HardSPL 1.24 over 2.03.
...
y want to instal spl 2.03 to test a modified room

Urgent! My diamond has hardware problem and need to fallback to stock ROM and SPL.

Hi,
My Diamond has no response on the screen, so I think I need to return to factory for repairing. However I have difficulties in falling back to stock ROM and SPL.
From the Wiki:
---------------
STEP BY STEP HOW TO RETURN TO STOCK SPL - FOR WARRANTY REASONS ONLY!
0. be sure to first restore stock OS, and stock radio. stock SPL is always to be done last!!
...
-----------------
I can't flash my ROM to latest HK WWE CSL ROM (2.03) as it just stopped at 0%. I'm using SPL-1.30.OliNex.
Questions:
0) Why? Any step I've missed? I've just copied the .NBH from HTC official ROM download. Should I get the .NBH from the Wiki instead?
1) Should I flash to v1.93 (the very beginning of the ROM)?
2) Must the RADIO be flashed back as well? or the above Stock ROM has included the RADIO already?
3) Anyone can give me a reference on the step-by-step in details...
Thanks!
Please help...
F810
Questions:
f810 said:
0) Why? Any step I've missed? I've just copied the .NBH from HTC official ROM download. Should I get the .NBH from the Wiki instead?
Click to expand...
Click to collapse
If the latest was the offical from the site then you could use that - as you are having issues flashing this with 1.30 HSPL, I would suggest updating that to 1.40
f810 said:
1) Should I flash to v1.93 (the very beginning of the ROM)?
Click to expand...
Click to collapse
This might be a easier option and should work woth the 1.30 HSPL
f810 said:
2) Must the RADIO be flashed back as well? or the above Stock ROM has included the RADIO already?
Click to expand...
Click to collapse
This is recommended
f810 said:
3) Anyone can give me a reference on the step-by-step in details...
Click to expand...
Click to collapse
Its really straight forward like the WiKi suggests
This Thread may help
Thanks a lot.
Re Q3, so do you mean if I extracted the stock NBH, it's only OS but not including RADIO? If so, I will get the RADIO from wiki page later. Would you please clarify for me?
After your information, I think the steps in Wiki are clear. Thanks.
If this is HK ROM is the one you have downloaded from HTC PAGE then it has a radio included
Since my Diamond is totally malfunction in the touch screen, I can't response to all the confirmation & prompts...
I've failed to install Stock ROM and tried your recommendation on upgrading to HSPL 1.40. There was a confirmation on running the program in my Diamond and I can't press YES and now my diamond is just like bricked.
I've also tried pressing VOL DOWN + Reset to connect the Diamond via USB. The ROM Update Utility has "successfully" update the HSPL, but actually when I hard reset it and found it's still running 1.30... Can I just use this approach to fallback to Factory status??
Anyone has good idea on how to fallback to Factory Stock ROM, RADIO and SPL, provided that my screen has totally no response to me?
PLEASE...PLEASE...PLEASE help.
You will not be able to update olipros Hard SPL in bootloader mode as the SPL is protected and the 1.30 will prevent this although show its been done.
What you will need to do then is just load a 1.93 ROM from boot loader. the were some in that link i posted earlier. as to reverting to the default SPL - you may be luck not to need the screen for any confirmation. but running a new SPL to overwrite Oli's you will need to use windows and the RRU
I've tried to load 1.93 ROM to my diamond but failed on OliNex 1.30. The link in modmydiamond.info on OliNex 1.40 Signed seems not correct, as it's still 1.30 after flashed. I've then flashed UNSIGNED 1.40 OliNex SPL (also downloaded from modmydiamond.info) and now flashing the 1.93 ROM in progress from bootloader.
I will flash the Stock SPL through the Bootloader after that...I hope I can successfully fallback and get it repair...
Last question (I hope), the stock SPL should be 1.37 so I want to confirm whether it can boot 1.93 ROM.
Thanks a lot!
Because these Unsigned HARD SPL 's are write protected.....you will fail all the time. Not sure if stock SPL can undue the write protection but if you still get stuck after you try then in order to bypass write protection I know Jump SPL allows for this.
band27 said:
Because these Unsigned HARD SPL 's are write protected.....you will fail all the time. Not sure if stock SPL can undue the write protection but if you still get stuck after you try then in order to bypass write protection I know Jump SPL allows for this.
Click to expand...
Click to collapse
you're right. When I flash the Stock SPL, it is "successful" but actually it doesn't update the SPL (i.e yet running OliNex 1.40). Where can I get the Jump SPL?
Here you go....I did a search
Hi,
Sorry to use this thread but im also trying to install back to my original Diamond ROM and am currently using the rom developed by Diamond Project (1.93.456.2WWE) and i kept flashing it back using Signed V1.93 RUU and apprently the Diamond project words still keep showing out when i start my phone!
How do i completely remove the Diamond Project thing? Thank you!
Read this............Scroll to Post #39
http://forum.xda-developers.com/showthread.php?t=400950&page=4
band27 said:
Here you go....I did a search
Click to expand...
Click to collapse
I also got that but it's not win32 program... I believe it's running on the Diamond. But I've hard reset, and never able to setup as it's screen was not functioning now...
kawatsu said:
Hi,
Sorry to use this thread but im also trying to install back to my original Diamond ROM and am currently using the rom developed by Diamond Project (1.93.456.2WWE) and i kept flashing it back using Signed V1.93 RUU and apprently the Diamond project words still keep showing out when i start my phone!
How do i completely remove the Diamond Project thing? Thank you!
Click to expand...
Click to collapse
That ROM had a different boot image - so you need to replace that by flashing another splash .NBH file using RUU.
Original splash can be found HERE
and if needed CUSTOM RUU HERE
Just un-zip these and put the splash file in the same folder as the Custom RUU and run the RUU - the flash should take a few seconds and viola - bye bye Diamond project splash.
f810 said:
I've tried to load 1.93 ROM to my diamond but failed on OliNex 1.30. The link in modmydiamond.info on OliNex 1.40 Signed seems not correct, as it's still 1.30 after flashed. I've then flashed UNSIGNED 1.40 OliNex SPL (also downloaded from modmydiamond.info) and now flashing the 1.93 ROM in progress from bootloader.
I will flash the Stock SPL through the Bootloader after that...I hope I can successfully fallback and get it repair...
Last question (I hope), the stock SPL should be 1.37 so I want to confirm whether it can boot 1.93 ROM.
Thanks a lot!
Click to expand...
Click to collapse
I think as long as the SPL is changed and the ROM is of the original language the I think it should be OK to send back like that
f810 said:
you're right. When I flash the Stock SPL, it is "successful" but actually it doesn't update the SPL (i.e yet running OliNex 1.40). Where can I get the Jump SPL?
Click to expand...
Click to collapse
As said before; you should be able to successfully run the stock SPL using RUU - if you are trying this via bootloader it will not work.
Which is the original SPL?? 1.23, 1.34 or 1.37? I do recall taking a picture of the original SPL when i 1st got the Diamond for days like that but i just can't find it now
I'm bought it from Malaysia. Anybody can help me confirm this??
R3PUBL1K said:
As said before; you should be able to successfully run the stock SPL using RUU - if you are trying this via bootloader it will not work.
Click to expand...
Click to collapse
I've tried to connect to ActiveSync successfully although the Initial Setup wizard on my Diamond. I've then run the RUU from RUU-SSPL-withoutNBH.zip and put the stock SPL .NBH file into the extracted directory. It can retrieve my device info, and when I confirm the update of ROM, after 3-5 sec it said about connection failure. I can browse the Internal Storage at the moment yet.
I've then tried similar thing using the Custom RUU inside the package diamond-hspl-1.34.zip. This time I can see 100% update. When I press VolDown and reset, the SPL is still v1.40 ONliEx.
What's wrong with my procedures above?
f810 said:
I've tried to connect to ActiveSync successfully although the Initial Setup wizard on my Diamond. I've then run the RUU from RUU-SSPL-withoutNBH.zip and put the stock SPL .NBH file into the extracted directory. It can retrieve my device info, and when I confirm the update of ROM, after 3-5 sec it said about connection failure. I can browse the Internal Storage at the moment yet.
I've then tried similar thing using the Custom RUU inside the package diamond-hspl-1.34.zip. This time I can see 100% update. When I press VolDown and reset, the SPL is still v1.40 ONliEx.
What's wrong with my procedures above?
Click to expand...
Click to collapse
I think I miss the step of running the SSPL-Manual.exe because of my screen is not responding... Anyway for me to put it into the Windows Startup Folder?? When I use ActiveSync I can't see Windows directory.
Please...please...I miss this step only...
f810 said:
I think I miss the step of running the SSPL-Manual.exe because of my screen is not responding... Anyway for me to put it into the Windows Startup Folder?? When I use ActiveSync I can't see Windows directory.
Please...please...I miss this step only...
Click to expand...
Click to collapse
Can anyone help??

SPL-2.03

Hi,
I sent my diamond back for repairs, and when it came back it came with SPL-2.03
As a result, I can not flash RUU_Signed_1_93OliNex_HSPL_UnsignedEdition which i need to install a cooked rom from here
Anyone have any ideas what I can do?
Thanks!!
you can't flash SPL 1.93???
My Diamond had SPL 2.03 and I managed to flash 1.93, maybe you're just doing something wrong.
I noticed there's a quite a few different new official SPL versions out there..
Can someone tell me if there's a difference in performance/battery life between hard-spl 1.40 & 1.93? I'd really appreciate it.
just run the sspl-manual from your device and try flashing HSPL after your screen becomes blank.

No matter what spl is installed - it always appears 1.93 OLINEX

Im having issues with SPL.
Originally, the device came with 1.93, so when I installed I installed hard spl 1.93 olinex.
Now I tried to do sim unlock and the guide asked me to go hspl 1.24, I tried to skip that step and go staright and install the patched radio, but it failed to update - error 226 with RUU.
I thought maybe its related to the hspl, so i downgraded to 1.24 but still I have that issue that I get error 226.
after i downgraded i still see in the bootloader mode spl 1.93 olinex.
I thought maybe to stock spl and then from there to hspl 1.24 and from there to patched radio maybe it will succed.
But even in stock spl it appears spl 1.93 olinex.
Also, besides that, i cant install the patched radio.
I appraciate your help..
Thanks.
I've noticed it the other way around, I first HardSPLed it with v1.40 and some later I flashed v1.93 (I think at least twice), without any error, but the flashscreen still says v1.40. Never had any problem though ...
Can't help you with the SIM unlocking, haven't tried it yet.
with the spl im mostly concerned because one day i might need warrenty and if it says 1.93.olinex..someone will probably suspect..
To Sim-unlock it doesn't matter you have HardSPL(Olinex) 1.40 or 1.93. The most important is your radio, you mut have the Diamond_Radio_1.00.25 intermediate to accept the SIM-unlock proces. Look at the thread .. unlock (sticky) and get the file - Radio downgrade - then you go. The error 226 is related to the radio version !!!
eranyanay said:
Im having issues with SPL.
Originally, the device came with 1.93, so when I installed I installed hard spl 1.93 olinex.
Now I tried to do sim unlock and the guide asked me to go hspl 1.24, I tried to skip that step and go staright and install the patched radio, but it failed to update - error 226 with RUU.
I thought maybe its related to the hspl, so i downgraded to 1.24 but still I have that issue that I get error 226.
after i downgraded i still see in the bootloader mode spl 1.93 olinex.
I thought maybe to stock spl and then from there to hspl 1.24 and from there to patched radio maybe it will succed.
But even in stock spl it appears spl 1.93 olinex.
Also, besides that, i cant install the patched radio.
I appraciate your help..
Thanks.
Click to expand...
Click to collapse
just flash this Spl : http://forum.xda-developers.com/showthread.php?t=400402 and then your problem is solved use the first zip download it worked with me

Categories

Resources