My touch screen is completly dead, and I tried to hard reset it but i got stuck on the alignment screen. Is there anyway to skip the align screen after hard reset? or is there any rom out there i can flash that will skip the align screen?
a62c said:
Is there anyway to skip the align screen after hard reset? or is there any rom out there i can flash that will skip the align screen?
Click to expand...
Click to collapse
Did you tried to flash back to radio 1.50 or lower?
Michele
You have to set you're pda in the bootmode ( reset button + ok and power button )
Then reflash youre pda with a other Radio Rom.
Good luck
I even tried to flash back to 1.48 and still im stuck at the align screen. I think the screen died at the same time i flashed the 1.51 radio. Now the real issue now is how to skip the align screen after hard reset because the touch screen is gone.
I'm sure one of the chefs could cook a ROM that skips the setup screens...
There is a remote alignment application that allows you to skip the alignment screen.....but you obviously wont be able to use the touch screen.
could you please give me a link of the remote alignment screen program? Im sure the touch screen is dead and i think ill be fine with the manual buttons.
Hope some chef will cook a rom that will skip this align screen thing.
I must be in a good mood, because I found this on google in two clicks....why you can't is beyond me....
http://216.139.221.18/downloads/mobile_speak_pocket/release/MSP_RemoteAlignment.zip
wow. it works! thank you so much. now i can use my phone again but the touch screen. i think i'll be fine without it. =)
Related
Hello, this is my first post here. I tried to install Windows Mobile 6.5 as indicated in Gizmodo http://gizmodo.com/5281397/how-to-install-windows-mobile-65-right-now but it didn't work and now my phone won't boot.
The phone is an HTC Touch Diamond from Sprint. I followed all the steps indicated and everything look fine, but after installing the OS the phone displays the screen TOUCH DIAMOND, and then restarts and displays the same thing. I'm able to get into the boot loader (Tri color screen) and says:
DIAM500
SPL-0.57.CMONEX
MicroP-Diam (LED) vB
PSOC-Diam STAGE_EVT v20.
I don't know what to do now
Thanks
try to load back to default setting by pressing the power on button at the top of the phone, before the "Touch Diamond" logo come up, press and hold volume down button and the center button until the three color screen come out, then release the two button you are pressing..
if the problem still happen, that mean the rom you are using should have risk on it..
give it up and try other rom or flash it again..
hope my suggestion can help you solve the problem..
dont worry.
if bootloader is possible as you write
than you can flash all time orig. rom back.
Flash from Olinex 1.40 screen?
okokur said:
dont worry.
if bootloader is possible as you write
than you can flash all time orig. rom back.
Click to expand...
Click to collapse
Hi I have the same issue on my HTC Diamond. I flashed wm 6.5 and it was working fine, then it hanged on titanum weather. I reset and it stayed on the HTC Diamond page, I did hard reset and got the Olinex 1.40 3 color page. It does respond from serial to usb when I plug/unplug. Can I reflash without active sync?
Turns out I was able to flash, but both roms I tried work well on 1st install, but stay stuck on the Touch Diamond screen everytime I restart de device. Is it a problem with the radio not compatible , or is there a specific Hspl for each ROM???
I found solution for this problem. If your diamond won't boot go to bootloader mode and upgrade your radio http://modmydiamond.info/index.php?option=com_content&task=view&id=15&Itemid=26 and after that your dimond worked fine without loosing data.
try to hard reset the phone by pressing vol down key + the center button + reset button.
if the problem is still like dat..
try to install another rom..
davidwong007 said:
try to load back to default setting by pressing the power on button at the top of the phone, before the "Touch Diamond" logo come up, press and hold volume down button and the center button until the three color screen come out, then release the two button you are pressing..
if the problem still happen, that mean the rom you are using should have risk on it..
give it up and try other rom or flash it again..
hope my suggestion can help you solve the problem..
Click to expand...
Click to collapse
Thanks davidwong007 for your help, I was experiencing the same issue as op and your method did the trick. For a minute there I thought I had bricked my HTC Touch. I did step by step what you suggested and ended up in the rainbox screen, once I was able to do that, I knew there was a hope. i did a full factory reset of the phone and voila the phone fully booted, the pain in the butt touchflow loaded. Very important thing I forgot to do in the past is to back up my phone, after the restore you will lose everything on phone, except what is in the internal storage. Thanks again.
Hi Guyz, Just bought a Touch HD and 1st thing i did was configure a 4 digit password. Since i live in china and Chinese for texting, i went on to try to install a old version of CE-Star (wm2003) on it, installation went fine, finally was prompted to do soft-reset, i did so, and then things went haywire, after coming out of reset the device diasplayed the initial password screen came up, realized that i cannot type in screen (totally un-responsive) and nor clicking on below 4 hardware butons causes any effect. I cannot enter into my device and hence cant do anything, stuck. Both Soft-reset nor even the Hard-reset surprisingly does not work (at wits end to get out of this dilemma, pls help). Pls help to resolve. Thanks.
if hard reset didn't work i think that this means that you have a faulty touch screen!
but i think you have not done Hard reset right,
do the following,
turn off the device
hold down vol up & vol down
press and release (only single click) the power button and wait for the instructions on the screen.
follow the instructions on screen untill the phone reboots.
i hope this will help
I recently tried to unlock my uncle's Diamond. I used Hard SPL1.4 from this site, and it finished that successfully. After restarting, I went through the whole screen calibration and so on, then I went to the kitchen to get some food. By the time I got back, the Diamond wouldn't start at all. I haven't tried a hard reset, but I don't think that would do me any good since the phone doesn't start up at all. Is there anything I can do? Or will I have to tell my uncle I ****ed his phone..
Just a quick detail, I did notice that after it started up again, the area next to the SIM card slot heated up quite a bit. I don't know if that's related, but I figured I'd tell you anyway.
The Hard SPL of choice is the 1.93. Any who, try and place the device into bootloader mode (tri-colour screen).
Hard Reset Your Device:
• Soft reset button and hold the vol. down + Circle button until u see the grey screen. REMEMBER THIS WILL ERASE EVERYTHING SAVED ON THIS ROM (i.e. contacts, calender, etc.)
Bootlaoder Mode:
• Soft reset and hold the volume down until u see the tri screen
Do you see the Hard spl 1.40? if yes, then just a hard reset and see what happens
IF none of the above worked, take out the BATTERY for a bit and try the above options all over again.
Hi, thought i would add to this thread.
Mine also did this, it worked fine for a week with Windows Revolution 6.5 rom then it randomly turned off and refuses to turn on.
Bootloader mode / hard / soft reset none work.
Ok, I know you probably get tons of these inquiries...I think I bricked my TP2, but am crossing my fingers that there is a way to 'unbrick' it.
I tried installing the "Timberwolf" ROM (Sorry I do not remember who the chef is). It completed as expected, but when it rebooted, all I get is a white screen.
There is no way to synch with my desktop so I can't simply install a new ROM. I've tried to boot from my SD Card (i.e. RHODIMG.nbh) and hard reset. When I do this, the bootloader comes up and when I press vol up, the install status bar completes within 5 seconds.
Please, please, PLEASE....does anybody know of any way to fix this?
Thanks for your help.
First, you would probably have better luck with a response in the Touch Pro 2 section.
http://forum.xda-developers.com/forumdisplay.php?f=488
Did you HARDSPL your Touch Pro 2 first?
http://thewingster.com/howtohspltp2.aspx
If not, try with the phone off, hold the VOLUME DOWN and press POWER on top.
Connect to PC.
Try to flash the NATIVE package for your provider, ie: A Stock ROM. Not the custom ROM you installed.
I have a Stock TILT 2 (TP 2) never flashed running basic programs Mobile Shell never had any issues with it, haven't installed new software in a few weeks , but I soft resetted it this morning and it keeps getting stuck in the boot screen. when first turned on it will run through boot screen then load screen for a millisecond then back to boot screen and never advances again , I've tried battery out sim card out Sd card out everything, even tried hard reset , but wont allow me to hard reset with front buttons and power, is there another way to hard reset , is it possible my phone just bricked for no reason ? thanks for any help ?
have you tried to do a hard reset via the pc? the original rom is on the htc website so you can try useing the exe file there. there is also an updated rom you can try to flash there. hope that helps
You might try sending it to the bootloader screen and reflashing. I don't know if it will work, but I thought it might be worth the effort.
I did notice that HTC removed the original shipped ROM for the Tilt2. I'm sure it is floating around here somewhere. If not, I have it and can send it to you when I get home.
Thanks I have original rom and just released wont work.
dod you see anythign on teh screen? if you do, then hard reset may fix it.
Power off your phone (or take teh battery out). Then press and hold teh call and hang up button while press teh power button. it will enter the hard reset mode. (remember hard reset will erase all the info on the phone and rever tot the stock setting).
jcterry said:
I did notice that HTC removed the original shipped ROM for the Tilt2.
Click to expand...
Click to collapse
wow, thank god i dl'd it when i dl'd the updated rom... and they still have the image of the old rom right beside it... lol
as for op, you can try to enter the bootloader with the following steps
Remove the back cover from the phone.
Hold the Volume Down button.
Use the stylus to press the reset hole.
Or if the device was powered off, press the power button whilst holding down the Volume Down button.
and try to flash from there
hope that helps again