Hi,
maybe something im missing here but i was at a friends house the other day and he has a wireless access point set up (open with no encrption set up yet ...just for testing purposes). so basically he is broadcasting his SSID. I turned my wifi on my m2000 and it picked up his access point and showed me that my phone had connected, with the WIFI signal enabled...however i could not browse or use the net which tells me that i was not picking up an IP address...wats going on here? any clues?
thanks for any help
K
kadabra said:
Hi,
maybe something im missing here but i was at a friends house the other day and he has a wireless access point set up (open with no encrption set up yet ...just for testing purposes). so basically he is broadcasting his SSID. I turned my wifi on my m2000 and it picked up his access point and showed me that my phone had connected, with the WIFI signal enabled...however i could not browse or use the net which tells me that i was not picking up an IP address...wats going on here? any clues?
thanks for any help
K
Click to expand...
Click to collapse
if the AP's DHCP sevice is off,you can't get the IP automatically
The DHCP is dodgy on my belkin router, so I have each PC and my BA set up to use a specific IP address, rather than rely on the iffy DHCP.
You may find you need to input a DNS if you do it this way.. just copy one off a working PC
Forgive me if I am talking utter c#$* but if you have established a connection have you not been allocated an IP via DCHP? Just taking a step back from router problems, when setting up the wireless connection did you set up for work or internet profile?
simjo, what you say is prefectly logical, but I have seen cases (as the thread poster was suggesting) where a connection has been created, but no IP addy issued. At these times, no internet access etc is possible. i.e. connection is said to be active, but it is useless.
My solution for this problem was as I posted above, dont bother with DHCP. Set IP addresses manually.
I have a similar problem on a new M2000 (so I'm probably overlooking something)
I can connect my PC and laptop to my router (D-Link 614) on WiFi without any problem
The M2000 can "see" the WiFi but there is no connection
When I try to view pages via GPRS there is no response
When I try MSN Messenger, same again there is no response
I've tried several soft and hard reboots, but no difference
I also find switching the "phone" on is very difficult as I am warned to "The phone is off. Do you want to turn Wireless on"
I then turn Flight Mode on, but am then warned that Orange GPRS cannot connect
I have managed to make some test phone calls, but the menus seem to be taking me round in circles...
Any advice welcome
My Best Roms - WIRELESS PROBLEMS FIXED!!
XDA IIs UK from O2 - WIRELESS PROBLEMS FIXED!!
1. Best ROM so far without doubt for me is the BA_TMNL_14200_119_11300_Ship from T-MOBILE
AND its the fastest ROM ive ever used!
2. Best ROM (slightly slower)
XDA 1.42 115 T-Mobile Firmware (uses Radio 1.13)
3. I-Mates 1.40 WWE with Radio 1.13
still had an issue with audio dropping from incoming calls
If you've seen any of my previous posts you'll see the hell i've been in trying to get anything to work with these ROMS, now it ALL works. and I dont say that lightly!
i tried the last 2 factory ROMS from O2 UK 140.237 & 140.242 which is there latest and I had WIFI nightmares with both of those..
I must have spent 30 hours swapping ROMs and this is the best Ive found so far now. Seamless Wireless Hookup everytime! I have Rude FM 88.2 Streaming Live through my Linksys Router at 64k 44khz using Pocket Music 3.2 , Surfing the Net, even the GPRS is stil enabled with the WIFI signal, a special lead pipes the audio to my Amplifier it's been on all day playing variouse stations, Windows Media Player streaming well, even download Skype over the XDA and installed it.
All
Can anybody help?... i have installed all the wm6 roms available (thanks to everyone that has created one of these) Anyway my problem is i have a bthomehub and i am having some troubles connecting the universal to the homehub via Wifi. The universal can pick up my wifi signal fine but then when i enter my encryption key the uni then comes back and tells me the key has been entered incorrectly ( i know this is not the case ) I have even tried removing the encryption off the homehub and the universal still does not connect. I know that there is not a problem with the wifi on the uni and WM6 as i took it round my friends and connected up to his dlink straight away.
Any suggestions would be most helpful
Nevamind folks. just solved my own problem for some reason it would only let me connect if i specified a static IP on my uni. Bit of a pain but still i can live with that..
Cheers anyways
strange, i just got the homehub with phone etc, and my uni connects no probs
hey guys,
i'm sure this has been asked, cant find the thread...
wifi on wm6 seems to dis-connect when vario II goes into standby...
and looses watever net connection u on...
anyway of sorting this???
dude, does your computer use the internet (WiFi not Ethernet) if it's on standby? I believe it does that to save you some precious power. Be happy.
Freeksta said:
wifi on wm6 seems to dis-connect when vario II goes into standby...
and looses watever net connection u on...
anyway of sorting this???
Click to expand...
Click to collapse
This is a default behaviour of windows mobile (even version 5 already did this) and the software that uses the wi-fi connection should take this into account.
(skype for example has an option to "avoid device suspend" when open)
I'd like to know if there's an easy way to keep the Wifi on in standby too, yes I know battery life will suffer, but that's my choice. I want the wifi on constantly for incoming VoIP calls to the mobile.
Is there anythingout there (appart from skype, i dont use skype for voip) that will keep the connection alive in standby?
Thanks
you may simply turn the screen off and this will keep the connection. not a good solution but it works, open wmp and assign a key for 'toggle screen', then you can turn the screen off easily
BT - WIFI interfirence
Try this on your Excalibur:
Establish connection with BT headset
Dial voice number
Activate WIFI at the same time
Did you hear any crackling and noise in your BT headset?
i'll try this a bit later when i get the chance, but isn't it common to have some interference if data is transmitting for both since they're both operating on 2.4ghz? also, what headset are you using? bt 1.2 should be better than 1.1
JwY said:
i'll try this a bit later when i get the chance, but isn't it common to have some interference if data is transmitting for both since they're both operating on 2.4ghz? also, what headset are you using? bt 1.2 should be better than 1.1
Click to expand...
Click to collapse
Well, I don't have this problem with TyTn.
I've tried Nokia BH 900 and Jabra JX10 - both 2.0
I'm glad i saw this thread. I'm having the same issue. I cannot stream music to my motorola ht820 bluetooth stereo headset if i use wifi. It just keeps stopping and freaks out on me. I was having issues streaming videos to my dash via wifi and using the headset also. I could not stream 100kbps videos over wifi! I thought the phone just wasn't powerful enough. (although it's not.. I could stream 300kbps videos on my old hp 3615 via wifi fine.)
I just was able to stream a video at 300kbps fine without bluetooth turned on using wifi and it worked fine. Grr!!
BT and wifi both use the same frequency.
I think you shoud try an other channel for the wifi. It may solve your problem.
Wifi how do you set IPs/DNS info?
did i over look something i can't figure out how to set IP, DNS and Subnet for my phone. I've gone to every connection screen did i over look something?
Internet via WiFi - Wireless Access Points Only
I am not subscribing to the data service on my cellular net. I only want to be able to access the net and email when I am in range of my WAP at home/work or at my favorite hot spots. I've got the WiFi settings so that I am connecting to my WAP and can see the SSID when it connects.. I've tried adjusting the settings in the IE options and am at the point where once in a while (1 out of 8 or so ) I can open access one page of a web site.. but can not navigate any further. If I type a different URL in it says locating and loading then times out.... what did I miss???
T-Mobile Dash / Re-ROM-ed to Excaliber.
All other functions seem to be OK.
Thanks, XmP
I've seen this as well. Playing around earlier today, I installed Opera Mini. Opera works fine over wifi or edge. I believe that the issue involves one or more IE bugs involving either the size (fragmentation?) of cache and/or scripts.
Also, Opera Mini isn't a solution (yet) either. It works great once installed and launched from the installer - but has to be uninstaller and reinstalled to work after you exit.
I can't wait for a linux port
I run into this problem all the time at my college and at my home. I turn on my wifi and the phone defaults to the network instead of wifi. I am on cingular with the 8125, I was using I/S PL 1.08 i just updated to cingular rom 2.24.10.1 WWE. I have tried IE, Opera, Mozilla (Minimo) and another i forget the name of. In all I preferred Opera but I feel Mozilla will be the best once the bugs are gone.
Oh yah and when I try and connect to the wifi network at my school they require a redirect to login through bluesocket. That is just too difficult for my little wizard and I rarely get through that system.
External antenna jack on Excaliber/Dash... is it just for GSM? or also WiFi?
Anyone had experience with the external antenna jack on the back of the Dash (under the mirror button)? Just wondering if using this connector would improve performance on WiFi? or is it designed only for GSM reception?
I found a cable which fits the connector perfectly. Thanks for your responses.
Issue solved!
I rebooted my wireless router and everything works great...
Bump!
I'm guessing the absence of answers means that the settings cannot be changed (or may need a reg hack to do so) - I can't find them anywhere either...
so it works for an external wifi as well?
yes, it is possible to change these settings (or at least the IP adress). I have read about it, but can't remeber where. It's possible to chnge it somewhere in the registry, can't be changed directly through settings. If I find it, where I read about it, I will post it here ...
As I remember the external is designed for car holder external antenna, not for WiFi. You may find at most of the GSM mobile back also have this.
This was posted over at howardforums too. What, you didn't search the internet endlessly to find an answer?
Above poster is correct, it's for GSM only. Like I said over at HoFo, unless you're lost in the backwoods, I don't think it's going to help much. Plus, it looks a tad silly!
Thanks for all your responses. Yeah, I posted the question in a couple of forums (the level of expertise varies widely, as you know!).
Reason I asked... we want to be able to access realtime weather conditions while at a remote nature facility on a barrier island here on the West Coast of Florida -- you know, like hurricanes There is a weak WiFi signal from an access point about 1/4 mile away. I simply wanted to establish a stronger link by using an external antenna.
So although it might have looked silly, it was to be a quick fix for instant weather updates (like radar), when needed.
Wifi connection sloooow. For you also?
Hi, with my stock htc s620, establishing a connection to a wifi network that is already saved (home & work), takes around 1 to 2 mins.
What often happens also is that it goes to sleep before even connecting (with me waiting in IE or mail to clic on a favorite or do a send & receive action).
I can't understand this since a nokia n80 will take seconds and it's almost instantaneous on my macbook.
Are there any tricks or software that can accelerate this (unless I'm the only one to have this problem)?
Seems to be a problem of your hardware or a configuration problem. I have energy save mode enabled and usually it takes two or three seconds to connect, sometimes up to ten seconds, if it has extremly low WiFi-Signal.
interesting, I'm going to investigate on the software part first... You really think it could be a hardware issue?
What's sure is that once the connection is established, it's fast and doesn't drop.
BTW, do you mean seconds after the handset is waken up from sleep?
Hum, after looking in my Remove section on my handset, nothing appears, is there some kind of registry cleaner for smartphone?
Hi,
with my old device (a XDA rebranded Touch Cruise) the internet sharing had the fine capability of keeping the bluetooth PAN connection alive even when the GPRS/3G connection broke down. It then tried to reestablish the GPRS/3G connection and sooner or later things fixed itself. The internet sharing app on the TP2 seems to disconnect the bluetooth PAN when the GPRS/3G connection goes down, which is quite an annoyance since i have to manually reestablish both connections all the time and this can become quite tiresome on a train ride where connection quality varies greatly within minutes. Does anyone know a registry tweak or something to make the application behave like the old one?
Kind regards,
Kork