I'm having this problem with my tytn after flashing the wm6 rom it dosen't matter the name of the rom because the problem always apear.
In this case the PrimarySplash and secundarysplash screen dosen't apear at full screen. For example the original htc PrimarySplash when flashed, at the bottom of the screen were you have the numbers when booting on the tytn i get a smal part off the last image that i had flashed whit the previous rom.
I have tried to flash only the PrimarySplash and secundarysplash but now luck
Does any one now how to fix this ???
Had this problem - for me, flashing a new ROM did the trick :
Before you go with that though - have you tried a hard reset and all the usual tricks? (in the Wiki?)
If all else fails - Assuming you're using hard SPL -
1. Use Dutties really good NBH tool,
2. Make an .NBH file including windows.nb and your 2 spash screens
3. burn baby burn...
This cured the problem for me - I assume that the previous flash I did somehow overwrote a few bytes of something it shouldn't have to cause the problem in the first place...
Try that but it dosen't fix the problem
Also tried to flash only the splash screen also didn't worked i'm starting to get with this bug.
Any one with another possible solution ?
You can always make your own Main and Sub splash screens, MrVanxs has an excellent guide to help.
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=20&Itemid=27
Related
I've been using Mun_rus's WM6 ROM for quite a while and seeing that PDAVIET's rom was built on a more recent WM6 ROM I decided to flash PDAVIET 2.07.06.PV.
Since then I cannot flash anything on my Trinity, the update utility starts and when the progress bar reaches around 84% half the screen on the Trinity goes funny. The progress bar on the PC reaches the 100% (while the screen on the Trinity goes blank slowly slowly) but upon restarting the device PDAVIET ROM loads up again intact as if I have just done a soft reset!
I've even tried flashing WM5 again but without any success.
Trying to flash Hard-SPL does not work either and I'm running out of ideas now :-( Anyone else has this problem please? I would love to try flashing a ROM with an original IPL SPL but cannot find one. My bootloader currently says IPL 1.5/SPL 9.99.CP.
Yes I am having a similar problem. It starts to flash then stops reboots and on my pc says image fiile corrupted. I have re downloaded and extracted the files but it happens everytime. However. My trinity when it reboots is stuck in the splash screen.
I had a similar problem, though not quite what you're describing. Try removing the Mini SD (storage card) before flashing.
Also, try entering bootloader fisrt before before flashing from PC.
Hope that helps.
i have the same problem...
i get 100% done and than it is still the old one..
Well, I have now sorted it. Go to this link read first post and download and use the unbrick.
http://forum.xda-developers.com/showthread.php?t=308691&highlight=splxploit-windows
I had to run it 3 times but it has worked and now I have flashed a new rom on it and it is working fine now
deniser said:
Well, I have now sorted it. Go to this link read first post and download and use the unbrick.
http://forum.xda-developers.com/showthread.php?t=308691&highlight=splxploit-windows
I had to run it 3 times but it has worked and now I have flashed a new rom on it and it is working fine now
Click to expand...
Click to collapse
I've run the splxploit a couple of times as well. It seems to finish the process succesfully but the problem persists :-( And mine is not stuck on splash screen, the device boots normally, it's just that whatever I flash does not work. Any more ideas please?
I tryed the all i think, read the all forum up and down, started in different ways, but no rom of SSL apply...
What is that!
I am stuck with this rom?
Any of the pro cookers can help with this please? I just need to understand what could be wrong, not necesseraly a solution
capeli said:
I had a similar problem, though not quite what you're describing. Try removing the Mini SD (storage card) before flashing.
Also, try entering bootloader fisrt before before flashing from PC.
Hope that helps.
Click to expand...
Click to collapse
Hey many thanks Removing the miniSD solved my problem I flashed at least a 100 ROMS in my life and never bothered removing the memory card before ... but there you go
hi, i had the same problem. i flashed my trinity with original htc rom and after that when i tried to flash with any other rom it gave me success message after every try but in my phone there was still the same htc rom. i used that : http://forum.xda-developers.com/showthread.php?t=293632 AND IT WORKS. FROM THE MOMENT WHEN I USED THAT FILE I FLASHED MY TRINITY 2 TIMES WITH THE SAME ROMS WHICH DIDN`T WORKED PREVIOUS. you need to copy that file to your trinity and follow the instructions from the readme file. in my case i only opened it ,it started bootloader mode ,i disconected usb and connected it again and started ROMUpdateUtility with rom which i wanted.
interesting... so why does the miniSD card affect the flash?
kta- had you tried running sspl and then flashing during your failed attempts? (just curious)
Ok, I have been trying to update to the latest official O2 exec rom, specificaly: Xda_Exec_Upgrade_v113188
I flash the rom, radio, well all that comes wit it and I get this weird screen (see attached pic). What can I do? Any ideas?
Thanks!
fernandosaez said:
Ok, I have been trying to update to the latest official O2 exec rom, specificaly: Xda_Exec_Upgrade_v113188
I flash the rom, radio, well all that comes wit it and I get this weird screen (see attached pic). What can I do? Any ideas?
Thanks!
Click to expand...
Click to collapse
happend to me once.
if you have the same problem as i did, you have a rom update that was written badly into the rom memory.
what you see is supposed to be a splash image, but because the rom is not written properly - all you see is a bunch of bits.
the reason it's "stuck" there is probably the same reason - the rom is not complete and it can't load.
1. put your device in BL mode
2. flash to a different rom (including a radio rom), preferrably one with spalsh images (jwright's roms have those usually)
3. make sure the upgrade reaches 100%
4. wait 10 seconds, then unplug & hard reset
if that doesn't work -
search the wiki on how to use MTTY to clear and reset the partition table on universal ('task 28 aa' ? if i remember correctly, but please double-check)
then after doing that, repeat the steps i wrote earlier, and you should be fine.
Hi,
I tried many times to install the hard spl version 1.34 on my new Diamond, but I have always the same problem:
- the program start
-it run since the boot loader mode appear on the screen
-then appear the progress bar and then ..... NOTHING.
I'm not new to flash and add new software, infact before the Diamond I had a Trinity flahed many and many times (Kaiser, Elegance Edition, etc....).
What can I do to solve the problem ? Really I don't undestand.
Please If someone has solved the problem post the solution.
Thank's
Post your SPL upgrade procedure, step by step.
We'll try to see where you might've gone wrong.
Did you sync your diam with active sync?
Did you try the spl-manual?
Maybe it is also good to give a link to the post you got the SPL from, so we know exactly which version you have (signed/unsigned).
I could not do it on my macbook pro either. IN teh end I resorted to boot camp and it worked fine
The procedure I made is still the same.
1. connect to activesync
2. start the exe
3. the screen of the diamond star the boot loader mode
4. appear the progress bar both in the pc screen and the diamond screen
5. the procedure stops and no data are transferred to the diamond
I tried all the three version of hard spl but the problem is still present.
The version of hard spl (from 1.24 to 1.34) is the one you can find in the first page of the forum.... belive me I did it many times in the past and I read very well the procedure suggested in the post.
However I will try to use boot camp.
Thank' s to everibody .
Dear Sir
My diamond got stuck up at the welcome screen or else in the alignment screen. I've flashed many roms number of times before but this time this happened after a hard reset- using Macadam 1.2 (latest).
My bootloader reads - Diam140 MFG 64M; SPL-1.40. Olinex. After this I've flashed back to the latest indian stock rom i.e. First to (RUU_Diamond_hTC_Asia_India_1.93.720.4_Radio_Signed_Diamond_52.62.25.34_1.13.25.24_ShiP) but know result & (RUU_Diamond_hTC_Asia_India_1.93.720.2_Radio_Signed_Diamond_52.29.25.12_1.00.25.07_Ship_R). After going through the forums- I understood that I've to step down to stock spl. But even after successful flashing, the boot loader shows the same- "SPL-1.40.OliNex".
I'm unable to use the jump SPL, because I can't pass through the alignment screen. Please help, is there any way to JUMP SPL without operating the phone.
Or else how can I come back to the stock spl.
Please Help.........................
Regards
Furthermore, I've tried using mtty to following the procedure:
Correct sequence is as follows:-
1. Launch ActiveSync on PC
2. Go to connection settings
3. Uncheck the Allow USB Connection
4. bring the device to bootloader. AND connect to the PC.
5. Now, run mtty1_1_.42_538 on PC.
6. CMD>task 29
7. Flash the ROM of your choice
Then flashed the stock rom again. But the problem remained.
jockyw2001 - suggested me on PM to do- "in mtty: set 16 0 then reboot'- but nothing happened. Or I didn't follow the correct steps... can anyone explain & help please....
[UPDATE]where do I get the commands for mtty
Can anyone tell me the link where I can get the commands to be used in mtty... Is there anyway to bypass the screen alignment part during start up after a hard reset.... how can I JumpSPL in a handset where the touch screen is not working.. but the screen is not completely dead, i.e. on tapping the "+" sign is moving after around 5 or 7 mins of the tap...
Please help guys.... I'm waiting to be rescued by some WM wizard from this great community.....
Regards
wizards- all'r failing or what- very few people with clear funda
cmonex please help....
hi man
i had the same problem, with all the rom around
than i understand that the problem was the radio rom
try to flash the lastest radio..i use the 1.13
Flash a Rom without screen alignment
Hi
If you on bootloader and you have 1.40olinex then flash a 1.13 radio then flash a Rom without Screen alignment process. It might help. Good luck
I did HardSPL v.1.40 and flash new rom
every thing seem going well, but cannot
boot, screen is freezing at the boot LOGO
I push a reset bottom, but it does Hard reset it-self
I am trying to do HardSPL other version
every thing seem going well also but
look like the previous version (1.40) still
exist!! what should I do???