Related
I'm having this problem with my tytn after flashing the wm6 rom it dosen't matter the name of the rom because the problem always apear.
In this case the PrimarySplash and secundarysplash screen dosen't apear at full screen. For example the original htc PrimarySplash when flashed, at the bottom of the screen were you have the numbers when booting on the tytn i get a smal part off the last image that i had flashed whit the previous rom.
I have tried to flash only the PrimarySplash and secundarysplash but now luck
Does any one now how to fix this ???
Had this problem - for me, flashing a new ROM did the trick :
Before you go with that though - have you tried a hard reset and all the usual tricks? (in the Wiki?)
If all else fails - Assuming you're using hard SPL -
1. Use Dutties really good NBH tool,
2. Make an .NBH file including windows.nb and your 2 spash screens
3. burn baby burn...
This cured the problem for me - I assume that the previous flash I did somehow overwrote a few bytes of something it shouldn't have to cause the problem in the first place...
Try that but it dosen't fix the problem
Also tried to flash only the splash screen also didn't worked i'm starting to get with this bug.
Any one with another possible solution ?
You can always make your own Main and Sub splash screens, MrVanxs has an excellent guide to help.
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=20&Itemid=27
I've been using Mun_rus's WM6 ROM for quite a while and seeing that PDAVIET's rom was built on a more recent WM6 ROM I decided to flash PDAVIET 2.07.06.PV.
Since then I cannot flash anything on my Trinity, the update utility starts and when the progress bar reaches around 84% half the screen on the Trinity goes funny. The progress bar on the PC reaches the 100% (while the screen on the Trinity goes blank slowly slowly) but upon restarting the device PDAVIET ROM loads up again intact as if I have just done a soft reset!
I've even tried flashing WM5 again but without any success.
Trying to flash Hard-SPL does not work either and I'm running out of ideas now :-( Anyone else has this problem please? I would love to try flashing a ROM with an original IPL SPL but cannot find one. My bootloader currently says IPL 1.5/SPL 9.99.CP.
Yes I am having a similar problem. It starts to flash then stops reboots and on my pc says image fiile corrupted. I have re downloaded and extracted the files but it happens everytime. However. My trinity when it reboots is stuck in the splash screen.
I had a similar problem, though not quite what you're describing. Try removing the Mini SD (storage card) before flashing.
Also, try entering bootloader fisrt before before flashing from PC.
Hope that helps.
i have the same problem...
i get 100% done and than it is still the old one..
Well, I have now sorted it. Go to this link read first post and download and use the unbrick.
http://forum.xda-developers.com/showthread.php?t=308691&highlight=splxploit-windows
I had to run it 3 times but it has worked and now I have flashed a new rom on it and it is working fine now
deniser said:
Well, I have now sorted it. Go to this link read first post and download and use the unbrick.
http://forum.xda-developers.com/showthread.php?t=308691&highlight=splxploit-windows
I had to run it 3 times but it has worked and now I have flashed a new rom on it and it is working fine now
Click to expand...
Click to collapse
I've run the splxploit a couple of times as well. It seems to finish the process succesfully but the problem persists :-( And mine is not stuck on splash screen, the device boots normally, it's just that whatever I flash does not work. Any more ideas please?
I tryed the all i think, read the all forum up and down, started in different ways, but no rom of SSL apply...
What is that!
I am stuck with this rom?
Any of the pro cookers can help with this please? I just need to understand what could be wrong, not necesseraly a solution
capeli said:
I had a similar problem, though not quite what you're describing. Try removing the Mini SD (storage card) before flashing.
Also, try entering bootloader fisrt before before flashing from PC.
Hope that helps.
Click to expand...
Click to collapse
Hey many thanks Removing the miniSD solved my problem I flashed at least a 100 ROMS in my life and never bothered removing the memory card before ... but there you go
hi, i had the same problem. i flashed my trinity with original htc rom and after that when i tried to flash with any other rom it gave me success message after every try but in my phone there was still the same htc rom. i used that : http://forum.xda-developers.com/showthread.php?t=293632 AND IT WORKS. FROM THE MOMENT WHEN I USED THAT FILE I FLASHED MY TRINITY 2 TIMES WITH THE SAME ROMS WHICH DIDN`T WORKED PREVIOUS. you need to copy that file to your trinity and follow the instructions from the readme file. in my case i only opened it ,it started bootloader mode ,i disconected usb and connected it again and started ROMUpdateUtility with rom which i wanted.
interesting... so why does the miniSD card affect the flash?
kta- had you tried running sspl and then flashing during your failed attempts? (just curious)
Hello.
I have installed a PV Hermes WM 6.1 Rom.
It now says : thank you for using this software...etc
I think it was for betatesters, and now it shows only a splash screen, and i CANNOT install another ROM.
I tried to install by starting in BOOTLOADER, but it does not help.
What can i do???
emipop said:
Hello.
I have installed a PV Hermes WM 6.1 Rom.
It now says : thank you for using this software...etc
I think it was for betatesters, and now it shows only a splash screen, and i CANNOT install anothor ROM.
I tried to install by starting in BOOTLOADER, but it does not help.
What can i do???
Click to expand...
Click to collapse
I think I read somewhere (but have not tried), do a hard reset, and when the screen that says Tap to begin using your device pops up, start attempting to flash from there.
But they "should" flash from the bootloader screen.
I had exactly the same problem. Tried all the tricks to go back to the previous ROM. I also tried boog321's hard reset idea, but it just puts you back into the bootloader. HOWEVER, when I then went through the screen alignment process (just for fun), lo! it works!
The problem is that i can`t get inside windows anymore. It stays at the screen 3 seconds after power up. Is there a way to hardware reset?
emipop said:
The problem is that i can`t get inside windows anymore. It stays at the screen 3 seconds after power up. Is there a way to hardware reset?
Click to expand...
Click to collapse
Just flash a different rom dude!! probably a expired beta rom.
i have tried to falsh 4 differnt ROM`s. It makes 2% and says rom orrupter or something.
Tried installing via MicroSD card? I installed the same ROM a while back...
Hey. I just re-flashed right now after I installed an expired beta by mistake.
Start with the Hermes connected USB, showing the splash out of luck screen.
1. Hold both Power and the ok button on the left and then RESET with the stylus. It should go in tri-color mode
2. Flash a known good ROM
Good luck!
Bro just flash your ppc using other ROM (flash it in bootloader mode) when its in the hermes rom upgrade tap the (force using safe SSPL) it will do the trick.
I already said i did that.
After 1% it stopped and says : ERROR 270. UPDATE ERRROR: The image file is corrupted please check your update utility.
I have done this with 5 roms now.
Will try microsd install.
Hope you have Hard SPL, you need it for sd card flash...
I solved the problem with the bad ROM.
I downloaded an official rom from here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_Upgrades
I has done a clean install.
But i still can§t install another rom, from the forum.
Will try again.
emipop said:
I solved the problem with the bad ROM.
I downloaded an official rom from here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_Upgrades
I has done a clean install.
But i still can§t install another rom, from the forum.
Will try again.
Click to expand...
Click to collapse
Are you sure you have HardSPL installed and CID unlocked your device?
I was attempting to change to ookba's 3VO ROM but the operation failed and the ROM did not install. I did get the recovery instructions screen and followed them but the phone did not reset to the previous ROM (NRGZ28's EnergyROM 52409). The phone hangs on the Windows Mobile screen. I have done the following -
1) Followed ookba's recovery instructions and gotten the tri-band screen. However whenever I try to flash back to the T-Mobile ROM (any version) I get Error 260.
2) Followed stylez hard reset instructions and gotten the reset screen but the phone hangs on the Windows Mobile boot screen. A hard reset does not occur.
3) Followed NRGZ28's "In Case Things Go Wrong" instructions and gotten the tri-band screen, however when I try to flash the EnergyROM (or any other non T-Mobile ROM) I get corrupted image errors.
4) I have used jockeyw2001's bootloader but get Error 260
Also, the power button does not turn the phone off. I have to remove the battery to get it to shut down. I think I have tried all the recovery steps I know if. If anyone has a suggestion or solution I would be most appreciative. Thanks.
The Rotagilla said:
I was attempting to change to ookba's 3VO ROM but the operation failed and the ROM did not install. I did get the recovery instructions screen and followed them but the phone did not reset to the previous ROM (NRGZ28's EnergyROM 52409). The phone hangs on the Windows Mobile screen. I have done the following -
1) Followed ookba's recovery instructions and gotten the tri-band screen. However whenever I try to flash back to the T-Mobile ROM (any version) I get Error 260.
2) Followed stylez hard reset instructions and gotten the reset screen but the phone hangs on the Windows Mobile boot screen. A hard reset does not occur.
3) Followed NRGZ28's "In Case Things Go Wrong" instructions and gotten the tri-band screen, however when I try to flash the EnergyROM (or any other non T-Mobile ROM) I get corrupted image errors.
4) I have used jockeyw2001's bootloader but get Error 260
Also, the power button does not turn the phone off. I have to remove the battery to get it to shut down. I think I have tried all the recovery steps I know if. If anyone has a suggestion or solution I would be most appreciative. Thanks.
Click to expand...
Click to collapse
Maybe its safe to assume you have a hardware issue? Since the initial flash and following consecutive flashes failed, maybe its a bad USB cable? I would try reflashing the shipped T-Mobile ROM from a different PC altogether using a different USB cable. Since your phone gets to the Bootloader (multicolor) screen means it's not bricked. Try different PC and cable hardware...
Will do. I did try another hard reset and the boot screen has sat for over 20 minutes without getting past it.
Or try flashin stock ROM via SD
you must flash to official rom to make any progress at this point. at least thats what i had to do when my computer auto-restarted in the middle of one of my flashes.
Fixed, thanks for the help.
bricked excalibur
how did you fix it cause i'm having the very same problem
Switched from a PC running Windows 7 to one running XP.
muga said:
how did you fix it cause i'm having the very same problem
Click to expand...
Click to collapse
Welcome to the forum
Also reading here would help http://forum.xda-developers.com/showthread.php?t=415225
Well that didn't work for me its stuck it the multi colour screen and pc not flashing it. When it does recognise and start to flash i see a count down screen like the one on pc but only stops at 3percent
muga said:
Well that didn't work for me its stuck it the multi colour screen and pc not flashing it. When it does recognise and start to flash i see a count down screen like the one on pc but only stops at 3percent
Click to expand...
Click to collapse
Muga, It's also happening to me. I had previous flashes with different roms Kavana's, rose, energy (6.1 release) and everything went well with no problems at all. But a few days ago, I tried to flash my excalibur with the latest release by NRGZ28 (energy rom 6.5) and what I think what happened was that I didn't run the unlock file aplications (since I didn't have to do it in the other flashes, because I already had unlock the phone with the first upgrade) that's the only explanation I can get. At the end, I came up with the frozen screen and I've tried the bootloader steps, original rom installation, hard reset with no succes at all. What I get is the same error you have.
I get the colored boot screen then "loading..." then the phone shuts off.
Any ideas on how to fix this?
TW,
Probably your phone is out of energy...
I feel stupid if it is... I'll slip it on the charger for an hour, thanks.
TW,
Battery was close to dead, duh!
However now it won't progress past the white screen "Loading..."
Thoughts or suggestions.
TW,
Flash from windows using custom rru
Making some progress.. Got a link to a good ruu, ATT?
Thanks,
When trying to flash via USB I get the error
"Invalid vendor ID".. then it quits and reboots.
TW,
Did you install hard spl?
Yes, it has hard spl.
Should I update it with a more recent version?
Try with 3.29
The soft SPL is 1.39... I'm getting a communication error now, could it be Windows 7?
I'll try at work in about an hour... thanks.
TW,
Did you follow this guide?
http://forum.xda-developers.com/showthread.php?t=433835
Already had a custom ROM on the phone so SPL should be there correct?
I'm getting error "262 Update Error"..
Tri-color screen shows SPL 1.93.0000
Trying to flash via SD, downloaded Cmonex's HARDSPL 3.29 SD and phone is just hanging at "Loading..."
I installed Android to NAND, will that have some impact on the restoration? Also will the verrsion of Android installed have some impact?
Finally got a ROM to load using the SD method... got the ROM from here:
http://f1ip.net/plug.php?e=index&f=./Downloads/KaiserFiles/Roms/OEMs
Thanks for all the help and suggestions..
TW,