Develop Bugs

ERROR 120, country id error. With USB v1.00 on my screen

Hi,
I tried to upgrade my MDAc with the rom from TMobile.
During the upgrade my computer asked for this file "wceusbsh.sys".
At that point the upgrade stopped.
No i only see "USB" and "v1.00" on my screen.
The charger led is red.
When trying to upgrade again, i get ether this message:
Error 120, country id error
or
err no device
I located the file "wceusbsh.sys" but still.
After "checking the information on your device" i get the error.
"Error 120, country id error"
How can i solve this problem.
Greg

You're stuck in bootloader. Did you try to upgrade to an other language?
You can try to hard-reset your device 'power & soft-reset' at the same time to boot your magician.
If it doesn't boot, kick it back in bootloader 'camera & power & soft-reset' at the same time for several seconds, till screen turns black & read 'serial v1.00'. When connected to usb it reads 'usb v1.00'
Now get maupgradeut_noid.exe from the ftp. Unzip your shipped-rom file you downloaded from TMO. Put the maupgradeut_noid.exe in the same folder as the unzipped files like maupgradeut.exe, enterbl.exe etc. Then execute maupgradeut_noid.exe instead of maupgradeut.exe this will give the error 120 once more. Just exit & execute it again, now it should proceed upgrading.
Cheers, M

=(
Same problem! Trying to use no id upgrade . I hope it will solve my problem.
P.S. DO NOT upgrade ROM when batt is lo =)

I've tried upgrading my JasJar with Xda_Exec_Upgrade_v1.30

I guys, I've tried upgrading my JasJar with Xda_Exec_Upgrade_v1.30.162, using MaUpgradeUt_noID and when update was complete I cannot load my JasJar anymore. I am using hard reset, but when choosing "0" off the boot screen - noting happens and screeen remains black.
Can someone please help me with this issue?
Thanks a lot in advance,
Best regards,
Stazik

Try reflashing it again. If it does not work, try reflashing back to the i-Mate ROM.

Whats the version of your bootloader (the screen with serial at the top changing to usb when plugged into usb)? If it is 0.56 or something else below 0.6 thats an already known problem.

I had similar problems with my O2 upgrade.
Try:
- Turn off USB in ActiveSync
- Hold Power/Light and press reset button
- Run the upgrade again

Thank you very much for help and support, guys!
When I try flashing my JasJar with Bootloader update or JASJAR_WWE_13076_164_10900_wwe_ship I get the same error message: Error 101 Connection Error. And also when I disable ActiveSync USB and plug my Jasjar into USB - I get a message from windows saying the device was not recognized...
The only I can get from JasJar is a black screen, except when I press two soft buttons and reset - that gives me a screen with 0 and x to choose. Neither of choices helps thou.
Any help is appreciated. Thanks a lot.

you didnt answer the question re the boot loader number.
when your screen is grey or starting to reset, there are numbers on the screen. what are they.
if it is less that 0.6 your in trouble and assistance is different to if your boot loader is 1.0 or similar.

My screen doesn't change from gray except when I do hard reset. And then I hit two buttons and reset, then press 0 the message Clearing now appears and then everything returns to gray again.
How can I tell the version of bootloader in this case?
Thank you in advance!

they are hard to see, if the screen is grey, the numbers are black.
f the screen is blue/coloured, the nmbers are probably red.

Thanks for help guys,
I brought my JasJar for service today, somehow they were able to put older ROM in there. Now I've upgraded bootloader, hopefully newest ROM from i-mate going to fit without problems )

Well I've killed my Jasjar upgrading I was installing the bootloader update. It sat there saying "Checking information on your device" for about 30 minutes after the update started (notes said it would take 10 so I figured something was amiss - disconnected & rebooted my PC.
Now when I turn the Jasjar on I get the USB/Serial screen referred to above and (good news I figure) it has v1.00 at the bottom. How do I fix this?
TIA

Sheesh. I did a search (I know I should have done that first) and found the answer here
Took a while to find a copy of mtty to download, but found that at http://buzzdev.net
Once I'd done the Set 14 0 and tried the boot loader update again it took seconds so something definitely went wrong the first time.

Upgrade question for a friend WM6 Official HTC

this is a question for a friend. He said he got these problems when he was upgrading to the official htc wm6 rom:
I've tried to ugrade my Orange SPV M3100 with this RUU, but with no success.
First issue: when i have connected the phone to the PC, established active sync connection and i run the RUU, my phone disconnect and show a screen with RGB stripes during the first "Verifying the information on your PC, please wait" screen. ActiveSync connection is disconnected so i can't continue the update process, and i must soft reset my PPC...
So i've tried to connect the phone after this step of instalation and:
Second issue: After i press Next button on the screen "You are now ready to update your ROM image", the progress bar shows up and the phone disconnect from the PC and turn off. After a while the RUU says "no connection"...
What am i doing wrong? I have image version 1.23.78.3 on my PPC. Please help. Thx...
Please can someone help him out?
Appreciated.

the 3 coloured screen popping up is normal with this RUU, I have upgraded two devices in the same way without problems ... did you leave the upgrade program running through during the "Verifying device / PC" phase or did you abort? It takes about a minute or so until the next window pops up on the PC ...

a question for a friend
mms6 said:
this is a question for a friend. He said he got these problems when he was upgrading to the official htc wm6 rom:
I've tried to ugrade my Orange SPV M3100 with this RUU, but with no success.
Click to expand...
Click to collapse
Im not expert and never purport that. I thing u need 2 tell us a little bit more.
Your currently ROM, SPL, if your device is Super CID or Hard-SPL etc. some one can help u
God luck

thank you to all of you. I will try to get some info on CID, SPL etc.
I will come back with some more info in a little while

have him download the ROM that MrV posted so his/your device does not need to be SuperCID and it should run just fine put the phone into boot loader before the update begins and should be fine

thank you very much

mms6 said:
this is a question for a friend. He said he got these problems when he was upgrading to the official htc wm6 rom:
I've tried to ugrade my Orange SPV M3100 with this RUU, but with no success.
First issue: when i have connected the phone to the PC, established active sync connection and i run the RUU, my phone disconnect and show a screen with RGB stripes during the first "Verifying the information on your PC, please wait" screen. ActiveSync connection is disconnected so i can't continue the update process, and i must soft reset my PPC...
So i've tried to connect the phone after this step of instalation and:
Second issue: After i press Next button on the screen "You are now ready to update your ROM image", the progress bar shows up and the phone disconnect from the PC and turn off. After a while the RUU says "no connection"...
What am i doing wrong? I have image version 1.23.78.3 on my PPC. Please help. Thx...
Please can someone help him out?
Appreciated.
Click to expand...
Click to collapse
This kicked my A$$ for about an hour as well. You'll never want to actually stop the installation to startup activesync. That's where things get jacked up! Just make sure that activesync can see the phone before you run the RUU_Hermes.......Ship.exe file.
1. Make certain that Activesync works before you start (I had to upgrade to 4.5) and synchronize the phone on the WM5.
2. Launch the RUU_Hermes......Ship.exe update and Click the "I Understand..." box and then Click Next. You're phone will display the Red, Green, Blue, White bars and show USB as the connection.
!!!!DO NOT REMOVE THE USB CABLE UNTIL THE ENTIRE UPDATE HAS COMPLETED!!!!! This is where you're making a mistake just like I did.
3. The Next Screen shows the Follow the instructions below.........etc. and it asks you to 1. Connect the PDA to the USB 2.Establish an Activesync connection..... 3. Disable the standby...... 4 Make sure Main Battery..... and it has a check box at the bottom.
!!!!! DO NOT TOUCH THE PHONE OR THE USB CABLE !!!!!! YOU SHOULD STILL SEE THE COLOR BARS ON YOUR PHONE!!!!
Just click the checkbox that says "I completed the steps as indicated above"
and then click NEXT.
4. It will say Verifying the information on your PDA Phone... Please wait..
5. You'll get the Update the current ROM version UPDATE box to click, do so.
6. You'll get the Verify that you want to update the ROM version screen, Click NEXT
7. It will go to the You are now ready to Update your ROM image screen. click NEXT
AND MIRACLE OF MIRACLES....You'll FINALLY see the Gas Gauge percentage screen update on your phone and the PC. Wait about 12 minutes, say a prayer for our troops, and get ready to enjoy WM6!
Hope this helps!
Schwazche

Error 260 on upgrade attempt

I have successfully installed Hard SPL into my HTC TyTN (Qtek 1.18.255 ROM) but I cannot get the ROM upgrade utility to work. I have tried using both the latest Qtek 2.11.255 ROM as modified for Hard SPL and using the upgrade utility as shipped (which I know would replace Hard SPL).
In either case the process stops at the point where I get the progress bar, I get through the verifying the information on your phone screens and confirming the ROM image but it never gets past the "Updating the ROM image on your PDA Phone" box.
The progress bar remains at 0% and eventually I get the message:
ERROR [260] : CONNECTION
The Update Utility cannot connect to your PDA Phone. Please check that your USB cradle/ cable is connected...
Needless to say the cable is connected but I notice that Activesync has disappeared at this point. There is nothing to do but exit the upgrgade. When I do, Activesnc reappears
Has anyone else come across this issue?
Help would be much appreciated
Simon

error [260] message every time

Firstly I would like to say thanks to this site and the trinityguides.info site for the great work people have being doing and making available to everybody, it is great being able to use my trinity with wm6, keep the good work going!
Now the issue I seem to be hitting the same "error [260] connection" every time I attempt to update anything on my Trinity. I have followed the advice on the trinityguides site regarding being stuck in bootloader mode to no avail, and I can't seem to find anything in the posts on the xda site which will rectify the issue.
Previously I have been able to update to AX3L v2.8.01 version without any problems, but I decided to update to sammy's ultra light, it initially kicks into des' crashproof sspl, but then it can't connect to the pc. even when I manually enter olipro's hard-spl it does the same. I have tried to re-install hard-spl, but can't. Disconnecting the usb option in the activesync settings doesn't do anything either. Does anybody have any suggestions for me please?
I am not even too sure if my trinity should have both Des' crashproof and hard-spl on it at the same time? Could someone advise me on whether this is alright please?
the tech details:
Trinity
AX3L_OS_v2.0.8.2
radio - 1.46.30 (even though it doesn't say this in the device info, or boot screen after soft reset)
Home PC - XP (just in case)

Did you also try flashing it again, the ROM I mean. I have this error also but as soon as I execute the ROM flash again it finds the device and starts flashing:
http://forum.xda-developers.com/showpost.php?p=1449597&postcount=2

I am assuming you mean flash with the new ROM, sammy's in my case?

yes, as described in the link I posted before. As soon as the error occurs, do not touch the phone, leave it, just start the ROM flash procedure again. (execute ROMUpdateUtility.exe)

No, I am in the same situation. The first attempt puts the device in 'ipl-sspl by des' bootloader mode then after about 10 seconds or so the error[260] is displayed on the pc. If I exit the ruu app and attempt again, nothing new happens on the trinity (i.e. it is still in Des bootloader) and the message is displayed again.

the thing is that when it first goes into des bootloader mode, the white strip doesn't have any text in it. If I pull the usb cable out then put it back in, 'serial' is then displayed in the white bar, but I am still in the same situation as before.

What operating system en activesync are you using?

On the PC I am using XP and Activesync 4.5

Check your connection settings to accept USB connections. Also, try using Hard-SPL 1.30 before flashing the ROM again.

deejacker said:
the thing is that when it first goes into des bootloader mode, the white strip doesn't have any text in it. If I pull the usb cable out then put it back in, 'serial' is then displayed in the white bar, but I am still in the same situation as before.
Click to expand...
Click to collapse
In your PC, try another USB connection.

BLOODY HELL!!! It is the simplest things which we often forget to try. Thanks Jotam for pointing out an obvious point, it must have needed a re-plug of the usb cable into another port for the pc to pick up the device again. I will remember that for future updates so I don't make a dumb ass of myself again. Thanks guys/gals.

Vista
Using Vista? if so which version?

Hi I asked this question yesterday, I am a noob :-[ but the only difference is I'm using Vista Ultimate.
Just for others who have the problem.
When you replug into another USB port (Luckly I've got two on my laptop..)
I used the Vista drivers from TrintyGuides and bingo !
now I try and flash a WM6.....English or Italian...maybe French.
Thanks for the help I keep you posted.
Richard

It works
Now to discover the joys of WM6 after only having WM5 for two weeks....

/i am getting the same only rom update 3.14.4.1 now sees the phone..
has the device name changed???
evene exploit no longer sees the phone

sorry, can you be a little more clear.. what ROM are you flashing, and what exactly is happening?
by the way... i thought error 246 was the connection error... am i mixed up? which is 260?

This seems to be on any rom bar the Dopod roms
and it says 260 connection error

Error 260 connection error - the phone is not going in to bootloader mode - and the RUU cannot seem to initiate communication with the phone.
I'm getting this a lot recently trying to flash.
However, Hold the power and camera buttons while resetting with the stylus (keep them buttons held down).
When you get to the bootloader - plug the phone in - wait till you see the USB at the bottom of the bootloader screen - then run the RUU again - it WILL work - every time.

I used to get this error message alot. sometimes the programs you install don't allow you to update even if you force the phone into bootloader mode so you have to hardreset the device and then upgrade.....hope this helps

htc diamond stuck
T-Rob said:
yes, as described in the link I posted before. As soon as the error occurs, do not touch the phone, leave it, just start the ROM flash procedure again. (execute ROMUpdateUtility.exe)
Click to expand...
Click to collapse
hi ,
my htc diamond stack, no respond on the screen i try to do hard reset with tree buttons but its not working, nothing happaned, screen stay home screen with the time and not responding touching the screen at all
please emergensy help