Hello people ..
I updated my T-mobile MDAIII from windows 2003 to "WM5"
it worked ok & looks cool but I can't connect to the network
& it work just as a PDA not a phone
also when I open "SIM manager" nothing happen & it doesn't open
even when I opend phone & dialed "*#06#" to retrive IMEI it hanged & I had to reset it & didn't show the IMEI#
I noticed also that it doesn't retrive the call duration & read "unknown" in both Incoming & Outgoing
also my phone has 128MB RAM, now it reads 96MB, is that normal with the new version ??
when I reset or hard reset it writes:
"No GSM
D 5.35.04. WWE"
1- if I updated to WM6, will it correct the problem?
2- is "No GSM" means it's not able to connect to a network
3- how I can reactivate the GSM service or connect to the network
Thank you for your help
Not an expert here but with the help from a member here (m a j u) both me and my brother in-law have successful upgrade our SX66 to WM5.
Try a soft reset (use the stylus to activate reset button) on your device everytime after you remove the battery, it work for both of us and should work for you.
Reset till the radio versions show.
Also some dialpad themes seem to cause issues with the phone (I had a problem with iphone theme for dialpad).
reflash radio rom
I'll try the re-flash method too. I've been having problems with a scheduled profile starting up the phone radio in the morning automatically. At night I turn it off but it doesnt come on in the morning, even though I know the profile comes on at the selected time.
Timofox said:
Hello people ..
I updated my T-mobile MDAIII from windows 2003.....
Thank you for your help
Click to expand...
Click to collapse
Hi, Make sure you have Radio Rom 1.15.00 and none of your profile turns the 'Phone' off automatically.
Related
Dear all,
I just got my imate jam (sold in Telstra shop in Australia) on last Friday, yesterday, I tried to upgrade the ROM as followed the instructions from http://www.clubimate.com/.
As imate jam has only one USB port which is connected to PC (Microsoft Active Sync 3.8) and there is no cradle, only 30s after I tried to update the ROM, then the USB is disconnected suddenly, and after that my Imate Jam has a black screen (it's like the backlight has been set to the lowest setting). I can see the word Serial 1.0, and if I try to connect to the USB again, it will display USB 1.0. Nothing more than that. Soft or Hard Reset doesn't change anything
Anyone knows how to bring it back to life, otherwise, I will return to the Shop since I only bought it for 3 days, hopefully, they will give me a new unit to replace this "dead" Jam :evil:
When I did the upgrade, the battery is at 100%, so there is enough power, but I can't understand why.
The ROM & Instruction are download from the page
http://www.clubimate.com/index.asp?PageAction=JAM
I've downloaded the Generic version of the ROM with the name ma_cdlsku1_wwe_10300_143_10100_ship.exe (28 MB)
with the following information :
The details of the current ROM image (found under Start -> Settings -> Device Info):
Rom version 1.03.00 WWE
Radio version 1.01.00
ExtROM version 1.03.143 WWE (Generic)
(PS. Sorry you may not be able to see that particular page and instruction if you are not a member for that site)
Any suggestions are highly appreciated.
Cheers
Wallace
PS. One more question, how likely is it for the Imate Jam / O2 XDA2 Mini to upgrade to Windows 2005 Mobile once it is available??
You are luckily in the Bootloader mode. I crashed during my PDA2K upgrade and found settings to get it into Bootloader mode and the upgrade was able to rerun and put the ROMs back in place. Try disconnecting, rebooting your PC (start clean), then, with the Jam in Bootloader mode still, relaunch the upgrade utility. Let me know if that works.
Also, do a search here on how to get the Bootloader to launch on your JAM if you need to pull your battery and power it back up again to it.
Oops ...
I've returned my imate Jam to the shop, and for some reason, they can do a hard reset on the phone (which I tried to press the power button and the reset buttons many times before), and so the screen comes up ...
And of course I told them I lost confidence in the phone blah blah ... and I want to replace a new phone ... So now they have sent my phone back to Telstra and need the Telecom's approval for a replacement unit ...
Once they approve it (it takes a week they said), I will ask for an O2 XDAII Mini instead. As in Australia, the imate phone has been customized by Telstra so it will by default shows the ugly logo of Telstra, whereas O2 will still display O2, and it has the options to choose which provider under "programs" ...
In the first 2 days, I need to soft reset the imate jam quite a number of times, I set the password so after the phone is unused, it will be locked ... but sometimes when I tried to unlock it, I couldn't ... I mean the number pad (virtually in the screen) has no reaction when I pressed it ... so I was forced to reset the imate jam a number of times, I suspect it might be problems from Telstra's customisation to the phone, but anything can happen so I just guess ...
Hope to get a new replacement phone soon ... as I only got the phone for 3 days ...
i tried to upgrade my xdaII to WM2003, Language id error occured then i read some post to handle it,it said that himagetdevice.exe should be deleted,then i deleted it.it worked but when it starts to install that message occured again and my xda stop functioning.anybody plz help me.now the display on my xdaII is black display and there's a text "USB v1.06".
Dead MDA
I had the same problem when upgrading mine.
The good thing is that you can still get to the bootloader.
You're going to need a copy of a ROM in EXE format for this procedure:
1. Upgrade your ActiveSynce to 3.8
2. Connect your phone to the cradle/cable.
3. Configure ActiveSync to use Serial connection only. It doesn't matter that you're using USB, just change the setting.
4. Start your upgrade from Windows.
Good luck!
u guys need to change the ID of your ms.nbf to your operator.
to change this you need to download a rom editor(its there in our ftp)
then just change the operator. then reflash again..
dont worry, as long as bootloader still works - its still ok.
hi to all
i have read the wiki of this blueangel,(but i dont found any solution)
this is the problem:
i have sim unlocked the BA, but when i put my sim card, the phone says "no service", and "unable to register on selected network"...all the times.
so, to "solve" this i did:
i update the room and the radio, with helmi room, and used the MaUpgradeUt_noID, to begin the update, i dont know if i am in the rigth way to solve the problem, but i have no more ideas...
another thing: sometimes when i turn on the device, at first screen(colored stripes screen) did not show number of the radio and another like G
and the worst: i have no backup of original room:
PH20B 0 B ESN N TELCE301 1.40.030 3, 1.40.178,1.12.00 12.00
PLSSS HELP ME!!!...
DARTHAS!SORRY FOR MY BAD ENGLISH)(
Newbie loses always the active sync connection just before updating its hermes from WM5 (OS 5.1.195 Build 14955.2.3.0) to the new WM6 (ENG Vers.). It's a MDA Vario II from T Mobile Germany (SIM unlocked!) and I have no clue what I am doing wrong - As soon as the progress bar starts to indicate the update my active sync connection goes down and of course I get the error message "failure connection".
Thx for any help! GeHu
I had the same exact problem. I can't pinpoint what exactly is going wrong (i just got my 8525 a few days ago, and decided to mess with it, so I'm a complete noob at this) but what I did was just use one of the repackaged versions. That did the trick for me D:
I am confused. If you mean you run a rom upgrade and then plug the phone in, then it is doing what it is supposed to do. You should fully sync your phone then run the rom upgrade. The upgrade will disconnect activesync and then put the phone into bootloader and run the upgrade.
gehu0003 said:
Newbie loses always the active sync connection just before updating its hermes from WM5 (OS 5.1.195 Build 14955.2.3.0) to the new WM6 (ENG Vers.). It's a MDA Vario II from T Mobile Germany (SIM unlocked!) and I have no clue what I am doing wrong - As soon as the progress bar starts to indicate the update my active sync connection goes down and of course I get the error message "failure connection".
Thx for any help! GeHu
Click to expand...
Click to collapse
It's an activesync problem. Either delete activesync and re-install it and then, try it again and it should work or try it on another computer
compudds said:
It's an activesync problem. Either delete activesync and re-install it and then, try it again and it should work or try it on another computer
Click to expand...
Click to collapse
Also make sure you have installed HardSPL first.
gehu0003 said:
Newbie loses always the active sync connection just before updating its hermes from WM5 (OS 5.1.195 Build 14955.2.3.0) to the new WM6 (ENG Vers.). It's a MDA Vario II from T Mobile Germany (SIM unlocked!) and I have no clue what I am doing wrong - As soon as the progress bar starts to indicate the update my active sync connection goes down and of course I get the error message "failure connection".
Thx for any help! GeHu
Click to expand...
Click to collapse
ok people notice how gehu0003 states "SIM unlocked!"......thus he most probably has a different bootloader.......1.40.olipro im willing to bet.
gehu0003...please do the following:
update to HardSPL v7 : This will make sure your SPL is up to date.
then
go to THIS THREAD....and download the DOPOD WM6 ROM. Use this repackaged ROM since it has CustomRUU which will recognise your updated SPL version. Enjoy.
thank u guys. i am fine now with the new HardSPL.
hey guys,
i'm having problems with this too, it disconnects me while i try to update to the hardspl.
any ideas?
thanks
how it worked for me
i had the same problem, while flashing rom, just before entering bootloader mode with some rom's it would disconnect and drop the usb conection. to fix it, now i enter the bootloader manually : press and hold (on) and (ok) buttons and reset with the pen. it should enter bootloader mode and in my case it doesn't drop usb conection to PC and allow me to reflash
cheers
Hallo,
I'm new in the forum, i was advised to register here in order to try and find solution to a problem my ks20 has after flashing a rom.
I tried today for the first time to flash a rom in my new ks20(i bought it yesterday used with cooked rom on), i followed this guide http://forum.xda-developers.com/showthread.php?t=369481.
When my phone tried to open, after flashing, this message came up "illegal use unavailable OTP Block".So i flashed another rom in order for the phone to open. With the new rom it opened but it had lost IMEI number and cannot connect with any phone network.
I have made a nv backup with LGMDP but when i try to use LGMDP to restore it i have the same message as before "illegal use unavailable OTP Block" when the phone turns on.
I tried with different roms branded and unbranded. I also tried this http://www.myphone.gr/forum/showthread.php?t=181820&page=360
I dont know what went wrong, nv backup procedure was complete, why do you think that nv backup is not good? I am ready to through the phone away
Maybe you can provide me a solution or another nv backup with my imei ( as i read somewhere in here) if the one i have made is not good.
Thanks , waiting for your help.
LGMDP_EURO that i used to change the rom created two folders: one is called NvBackup and the other folder is named with my imei number, i used both .nv2 files that are included is these folders but every time the result after restoring was the message "illegal use unavailable OTP Block".
I don't know what to do!
Please if anybody has a clue
what rom did you last install?
Was it the branded or unbranded version?
The last rom was Greece Vodafone 10g it is branded.
The problem when i tried to install a cooked rom which i think it awas also branded.
My phone is vodafone branded
did you restore your nv2 in emergency mode?
no i installed a new rom (so that the phone could turn on ok even with wrong imei) and i tried to restore with the phone turned on
shut down your phone, start emercency mode(press : "Send" "Browser" "Power") a green led will shine on your mobile and connect it, and try to restore your back up nv2
how can i do that from emergency mode? i don't have "nv Default" option, also there is no "reset database & contents"
if you have msn send me your email adres in a private message.
Unfortunatelly i dont have msn but i have facebook account.If you have one we can talk from there
sure is the same
I have sent you my account by pm
rickou26 saved the day.
Thank you very much
pagia said:
rickou26 saved the day.
Thank you very much
Click to expand...
Click to collapse
Hi pagia,
I have completely the same story as you.
Could you please share how did you solve it ?
Thanx
Switchke said:
if you have msn send me your email adres in a private message.
Click to expand...
Click to collapse
Hi Switchke,
I completely have the same story as pagia, could you please help me ?
I do not have msn but a pm could I send my pm ?
Thank you in advance.
zezika said:
Hi pagia,
I have completely the same story as you.
Could you please share how did you solve it ?
Thanx
Click to expand...
Click to collapse
Did you solve your problem?
If not give rickou26 your imei number and ask him to make you a backup nv2 file.
use the program MTTY because it's only USB or has unlock without backup (like me) and has still bluetooth activated car solve the imei and bd address problem with that (should be works with usb cable also) :
1) get the phone recognized by windows and activate modem serial port interface
bluetooth perifs-> properties -> services -> check the 2 boxs
3) start -> programs -> accesories -> communication -> hyperterminal ->
set a name and modem port (should be found in step 1)
'call' (yellow phone)
4) type "AT" (without quotes) should see "OK"
5) type ATZ (activate echo)
6) AT%IDDE to unlock
7) AT%IMEI=X,X,X,X, ....
(15 chars) replace X by IMEI code or what you want
8) AT%BTAD=X,X,x,x,x,x ...
(12 chars from 0x0 ->0xF) same for bluetooth address, warning : the digits are in little endian (inversed)
9) switch off and on and the bluetooth should work again without asking for BD address
this method has worked for a KU380 only by bluetooth without install third party program to backup or repair and should works for other phones
help this dummy out ...
i met with the similar issue....
flashed my ks20 to upgrade to win 6.1
lost IMEI, bluetooth ID,...
QPST recognises the fone in 'download mode'...
so what can i do to recover my fone?
hi
hi all, i have just the same problem with ks20. I dont have imei and i do not backup the nv files. My phone is just a pda, no signal. On the back of the phone my imei is 357323-01-085909-3. Please help me, i have email [email protected]