Hello, I have an ASUS P525, since yesterday, there is no sound in my machine and I'm going crazy. Sometimes, the sounds of the system (screen tap, voices of TomTom, the sound of Media Player) dissapears but I repaired it doing a soft reset. Since yesterday, this soluction doesn't repair the sound. I have done a hard reset and nothing. Even I have tried to reinstall the 3.32 WWE version I have still there is no sound.
If I connect the earphones of ASUS to the jack, all goes good. Theres is sound of TomTom, the Media Player goes and the screen tap, alarms, all. I have installed all the patches of BT, radio 4.5 and WWE 3.32.
I think there is a software problem and not a hardware problem (loudspeaker cable disconnected) becouse when I receive a call, it sounds. But if I hang up this call I can't speak and the other person doesn't hear me. However, if I go to sound systems and play the sound of an incomming call, there is no sound.
When I have reinstall the firmware, I think that the installer Galaxy haven't reinstall the files becouse only have read the Galaxy.cap. I think this becouse there is the same version. I don't want to install French version becouse once I've install it I can't go back to the Enchlis version.
Please, help me, thanks, Goyo.
Goyete said:
I don't want to install French version becouse once I've install it I can't go back to the Enchlis version.
Click to expand...
Click to collapse
Are you sure about that?
This is a faulty 2.5mm headset connector on the PDA
You have shorted contacts in the "headset inserted" detection switch, making PDA permanently in headset mode.
Since this is a hardware fault, dont bother updating software etc. Basically you have two options:
1) Insert/remove headset jack several times. Sometimes it makes dislodged switch contacts properly work again.
2) Replace the unit.
Ingvarr is right, it's a common problem to all PDA audio jack
I have had this problem on the xdaII. If you insert a damaged headset plug into the jack it can screw up the sequence of pins detected as it slides in. It is not as simple as putting a new one in and out (unless your very lucky). I had to get a wire and poke it in there and play with shorting the connectors in different sequences. It took a while but when I got the "magic" combination it went back to normal (and the faulty headset went in the bin).
warning: That device totally lost its ability to make sound without the headset about 1 year later. It may or may not have had something to do with what I did, but if you are worried then take it too a repair shop.
Very thanks to all, I was getting crazy trying several options to solve the problem. In fact, the PDA sounds when a call is entering but I can't take the call becouse I don't hear nothing and the other person doesn't hears me. Yesterday, I was trying to put the headset jack in and out becouse I thought that the problem is whith this (I have read your post now). Another thing about this problem is when I put the headset, the Voice Dialler starts up automatic so the problem is in the jack, you are in the truth...
This night I'll try to put in out the headset in the jack to solve the problem becouse now I haven't the headset with me.
I have sound!!! I have inserted a metalic pin in the jack and the PDA sounds fully of sound... Thanks a lot to all of you, I'm very happy. I was very since friday.
Hey Goyete!!! , don't do more experiments with old headsets
User22 said:
Hey Goyete!!! , don't do more experiments with old headsets
Click to expand...
Click to collapse
Old headsets?, My PDA had crash withe official ASUS headset for the P525 Are you spanish?
Goyete said:
Old headsets?, My PDA had crash withe official ASUS headset for the P525 Are you spanish?
Click to expand...
Click to collapse
Spanish ? , are you jocking ??? , i am the same one that is posting at www.todopocketpc.com !!!
I use the Seidio headset that i bough for my previous Qtek S100 (allready sold), and i didn't have any problem with it.
User22 said:
Spanish ? , are you jocking ??? , i am the same one that is posting at www.todopocketpc.com !!!
I use the Seidio headset that i bough for my previous Qtek S100 (allready sold), and i didn't have any problem with it.
Click to expand...
Click to collapse
Vaya tela, yo tambien me llamo Goyete en Todo Pocket PC. Ya he curioseado y he visto que tienes una P525. Lo que son los foros... Gracias otra vez.
!! Merci !!
I had the very same problem with the sound on the P525
I thought the speakers were KO
But after reading your thread, I insert a wood match in the jack, while playing music. The sound came back instantantly.
Looooooooool
This stuff is so easy !!!
(I did use too a bad 2,5jack some weeks ago, but the sound disapears weeks later...)
Thanks for the help
i saw this problem b4
i had xda2 mini and i had this problem ,so i send it back to O2 .and they send me a new one.after a while i got the same problem ,so i knew that the 2.5 to 3.5 is faulty ,so i got another new pda from o2 .
now i have asus p525 and i dont wanna experiance this again .i am using the original headset only.
BTW the XDA2 mini had better sound and louder then the asus on 2.5 and 3.5 headsets.
I had the same problem but reading your post i resolved, only 1 thing is still bad.
during a call if i try to press the boutton (in the touch screen) speaker on or off nothing happens. i don't know what to do. someone can help me writing where in the registry i have to check if is it all ok?
sorry for my bad english.
horeb
sorry for bumping such a old thread, just recently my p525 is F*cked up again, after removing the headset from the put there's no sound. so i thought it was the old problem, but then i've notice everytime i remove or insert my headset, the voice command would pop up, and no matter how many times i insert/remove the headset the music won't come back on, i've updated it to wm6, anyone have a clue of what's going on?
Same problem
BUt i rezolved inserting inside HF jack a stick of wood, and rotating him. After that , surprise my sound comme back to life.
Hi guys!
I've just suck now with my p525, cause I tried to solder the 2.5 jack slot out of the mainboard, but the sound did not come back
Any hint?
There is no software solution for that???
I wonder if any still has the p525 in hand. The mute speaker is really a defect of the 2.5 mm jacket that I have just resolved. My way is simple: dissemble the phone until the 2.5 mm jacket is exposed, then make a relatively big hole with a lighter heated screwdriver enough to reveal the copper plates that contact with the head of earphone. With a tiny tool or anything, move the copper plates "away from the wall". Done!
Loss of the elastic recoil of the plates is the cause of a mute speaker, not a dective earphone, I think.
Related
I'm having several problems with my Qtek 9090
There's a rather loud constant high-pitched noise comming from the screen whenever it is turned on (which is when the device is on!). At first I though it was comming from the speaker, but the screen is definitely the source of the noise. It doesn't matter if the backlight is on or off.
People can't hear what I say when using the phone - it makes no difference whether I use the included headphones or just speak directly into the microphone.
I haven't been able to find a BT headset that works with it. They all have the same problem; The sound scratch so much they're unusable. I tried 3 different brands that all works well with my 2020!
The GSM link often "falls out" - even though there's plenty of link the phone doesn't work (nothing happens when I try to call someone). A soft reset solves this problem!
As you can see, I can hardly use the device as a phone at all I've had the device replaced once, but all the problems persists on the replacement.
Does anyone have similar problems?
1. No, don't have this problem. Strange that it happened on the replacement too.
2. Yes.
3. I have just ordered a jabra headset in the hope it will fix problem#2.
4. Yes.
These problems with GSM are a real headache. One of the primary reasons for buying the PDA2k was to consolidate my mobile into one device. I have seen other people experiencing such problems but from what I could gather, voice over BT worked much better. Have you updated the ROM since you bought it? I should know the answer to 3 today, if DHL delivers, and I can tell you I will not be a happy man if the answer is Yes!
Try a Motorola HS810 headset... works fine for me.
harry_mb said:
1. No, don't have this problem. Strange that it happened on the replacement too.
2. Yes.
3. I have just ordered a jabra headset in the hope it will fix problem#2.
4. Yes.
These problems with GSM are a real headache. One of the primary reasons for buying the PDA2k was to consolidate my mobile into one device. I have seen other people experiencing such problems but from what I could gather, voice over BT worked much better. Have you updated the ROM since you bought it? I should know the answer to 3 today, if DHL delivers, and I can tell you I will not be a happy man if the answer is Yes!
Click to expand...
Click to collapse
I've already tried Jabra Freespeak 250, which didn't work for me
No I haven't updated the ROM as I've been told by the supplier that no new version is available yet!
outz said:
Try a Motorola HS810 headset... works fine for me.
Click to expand...
Click to collapse
I also tried both a Motorola and a SonyEricsson BT headset, but I don't remember the specific models - they both scratched immensely
i use SE 60 and it works ok
As you said, the Jabra250 is pretty much unusable!
Crackling is not constant but goes in waves, even though I do not move.
Am at a bit of a loss what to do now... the device is great apart from this.
>> People can't hear what I say when using the phone - it makes no difference whether I use the included headphones or just speak directly into the microphone
yes PBT read my other post
I have the same problem!!
it is scandalous to sel an device with this big defect!!
Sony HBH-660 works good for me.
People say that they can't hear me when I use the handset, but I don't have any crackling, etc with the headset and voice is clear. You just never know if the headset is going to connect when the phone rings though.
sound from screen
there's a rather loud constant high-pitched noise comming from the screen whenever it is turned on (which is when the device is on!). At first I though it was comming from the speaker, but the screen is definitely the source of the noise. It doesn't matter if the backlight is on or off
Click to expand...
Click to collapse
I have this problem also, I was told to use the new rom but this has made no difference, Please let me know if you have found a solution
[/quote]
Guys,
the hissing coming from the screen is a power supply problem. keep swapping phones until it goes away! I used to build switching power supply and the hissing (in a system designed to operate well above 20kHz) is only able to be heared when unstable, inductor core or cap is broken. The hissing is very 'not normal'.
It appears that the Q9090 is standing out as having more problems than the MDAIII, one is the mic volume, most of the other phones are not complaining about this so there may be something with they way the Q9090 are updated or shipped.
With the Jabra 250, don't forget to pair it pressing BOTH the volume and phone button on the headset on discovery with the 9090.(On bonding, turn off headset, turn on again pressing both buttons)
Funny thing is, I had the cracking also. I deleted the headset in BT manager and paired it again as described above. Now it works ok.
Hi,
I bought a Qtek 9090 a few days ago and I also have the same problem with volume level. People can't hear me when speaking, either with the headset or base microphone.
Using a different headset doesn't help (that's even worse sometimes) but I didn't try a BT heaset (and I don't want to as it would raise potential connection problems). I'm going to contact Qtek for support on this...
Pierre
I too am having problems with the Jabra 250 BT headset and my SPV M2000. The Jabra 250 worked fine on the XDAII but is terribly crackly on the newer model.
This is even when pairing it with the enhanced pairing of pressing Volume Up and Phone button together to pair.
Any ideas?
qtek 9090 bluetooth problem
Hi All,
I have new qtek9090 with cellink bluetooth headset. It is work normal, but i am loosing connection to headset each time qtek go to stand by mode. I need to switch off/on the bluetooth in order to restore the connection. Any ideas?
I often get a message stating:
"The Bluetooth Radio failed to turn ON due to insufficient driver momory available. You must perform a normal reset before you can turn ON the Bluetooth Radio."
Does your device also give you this message?
Is it also using the Broadcom "Bluetooth for Windows CE BT-PPC/PE Version 1.0.0 Build 2200"?
Interested to know if you have the same problems with the same bluetooth driver.
same problem
My qtek 9090 shows te same problem
This is a known problem with the Blue Angel, unfortunately, until they bring out a fix, all you can do is a soft reset.
upgrade
hi all,
how can i get updates from www.imateclub.com?
I can't register there, because I have qtek 9090 and not i-mate
thanks
O2 Sourced info on which BT headsets work
See: http://www.my-xda.com/downloads/Other_Bluetooth.pdf
Hi,
Is anyone using the Jabra BT250 with QTEK9090 without problems? if so, what have you done?
I bought this headset, paired it with the QTEK and..... crackling! craclking and more crackling.... the only way i can get a clear sound is when i put the QTEK close to the headset (5-20cm) if it wasn´t sad it would be funny, i have to hold the QTEK next to my ear with the hearset on, if the unit is in my pocket or on the other side of my body... well.... not one word is understood... just crackling! 10 meters haha... it´s a joke!
I can´t believe HTC is selling 1000´s of units with this kind of problems!!!
It´s supposed to be a PHONE!!!! you can´t use the unit because of the low voice issue with the mic, you can´t use the headset because you have also the low volume issue... and you can´t use a BT headset because of all the BT issues... GREAT!!!
vega.
I have problems with my jabra and mda3 - I have to have the phone on the same side of my body as the headset otherwise it's too crackly.
I also have a PDA2K and a XDA2s, and use Jabra 250 and 250V I have the same problems as you. I used the second update from Imate it dose seem to make the Bluetooth More stable, but still you need to hold the phone near your head to stop the audio crackle.
I also spoke with Jabra as Imate are now saying there is a fault with Jabra headsets, The Guy at Jabra had a good larph about that.
Have you read the description???
Hello together,
i think you should read the description of the Jabra carefully.
They write, that you have to put the bluetooth-device on the side of your body, where you put the Jabra on your ear."Because the human body can make interferences."
Second, i think you have paired your device with the jabra in front of you. Don't do that. When the devices will pair, they changes some parameters of frequences. So do that:
Put your headset on your ear, search for devices on the pda, and after you put the code in, put the pda on the position where you will wear it.
After 30sec. look if it is OK! Than test, if it is crackly.
When it is not OK, delete the pairing devices, Reset both of them, go to another place (2m away, because of interferences) and try it again.
So, in the worst case, after 3 times, i have no crackly!
Good luck, Mario
I'll give that a go
..and has anyone seen any benefits with the Jabra250 after applying the second BT patch?
No... it´s the same... after the BT patch or with SuperMario´s tips above the crackling issue continues...
... i phoned JABRA support and they told me that it has something to do with the BlueAngel internal antenna...
...and that it was the same with the XDAII...
what i find strange is that i´ve already read somewere a XDAII user saying that he managed to fix the crackling with his jabra BT250! i don´t think he stated HOW!!!
and again i ask : Is anyone using the Jabra BT250 with QTEK9090 without problems? if so, what have you done? pplllleeeeaaassseee!!!
BT and JABRA - the saga continues
No... it´s the same... after the BT patch or with SuperMario´s tips above the crackling issue continues...
... i phoned JABRA support and they told me that it has something to do with the BlueAngel internal antenna...
...and that it was the same with the XDAII...
what i find strange is that i´ve already read somewere a XDAII user saying that he managed to fix the crackling with his jabra BT250! i don´t think he stated HOW!!!
and again i ask : Is anyone using the Jabra BT250 with QTEK9090 without problems? if so, what have you done? pplllleeeeaaassseee!!!
Re: Have you read the description???
SuperMario said:
Second, i think you have paired your device with the jabra in front of you. Don't do that. When the devices will pair, they changes some parameters of frequences. So do that:
Put your headset on your ear, search for devices on the pda, and after you put the code in, put the pda on the position where you will wear it.
After 30sec. look if it is OK! Than test, if it is crackly.
When it is not OK, delete the pairing devices, Reset both of them, go to another place (2m away, because of interferences) and try it again.
So, in the worst case, after 3 times, i have no crackly!
Click to expand...
Click to collapse
^^ Try That!!
I´ve already tried that several times... tried it again... that tip doesn´t seem to work for me!
i´m getting really frustrated with this...
thanks anyway...
O2 have already admitted the problem with the Jabra BT250, their UK product manager sent me this link which shows the compatibility issues with BT stuff:
http://www.my-xda.com/downloads/Other_Bluetooth.pdf
Tommy
hello, I am having a strange problem with my blue angel.
I dont have sound at all.
suddenly without apply anything strange to the phone. The strangest think is that sound is back after some time and then again lost.
I dont know whats wrong,
I tried resetting the device, I tried hard resetting, I tried even reinstalling the rom. I tried scan with an antivirus. NOTHING worked!.
When someone is calling me the phone vibrates, when I answer it, they can hear me but I dont listen anything.
Sometimes the sound comes back.
When I call someone and try to put speakerphone on (by keeping the green button pressed) the speakerphone does not come ON.
If it was a problem with the speaker, the speakerphone would show that is enabled but will not be enabled right?
**** I am so confused, I cannot use it as a phone at all.
With a hands free it works OK, and thats how I am using it.
Please guys if you have any idea...
anybody that unscrew pda2k?
have u tried the undirectional patch from pda2k? / try the most stupid thing, on ur bluetooth all the time & c if it works. :lol:
what is the undirectional patch?
is fixing what?
The unidirectional patch is available here
http://wiki.xda-developers.com/index.php?pagename=BA_FAQ_Unidirectional
It will [probably] solve the issue you are having.
I have this problem too.
I tried to download this patch, but i cant do this! Its written: "530 Permission Denied."
What is it?
Can anobody send it me by E-mail? Pleaaaase!
I have fixed the file's location. Please revisit that page to download from the updated link.
Thanks man!
Sound Problems, calls cutting out
I have a similar problem in that calls come through but the speaker CUTS OFF just as the Sampled Ringtone plays the first 10th/sec , I use 11khz 16bit Mono Wavs - only 3 second loops, please check my post as well "Choppidge" at the base of page. Sometimes they just dont play at all, but do when I soft reset, the battery is almost fully charged. I will try MP3 patch as they dont play in Rings folder either. and this problem still occurs now that I have upgraded to 1.13.00 RADIO ROM.
http://forum.xda-developers.com/viewtopic.php?t=31090&highlight=mp3+rings
Do I need the unidirectional Patch?
I also get problems pairing to my JABRA BT200 bluetooth Headset, soft-reset etc, its been so bad I had to get another phone
It is caused by the conflict between the BT Tray and the phone system
Unidirectional patch screws up screen graphics
After 2 hard reserts and restores
The Unidirectional Patch dosn't work for me it screws up my screen graphics
So does the MP3 As Rings patch god I hate O2 for this !!! still no new firmware!! :evil:
The sounds arnt playing at all, any of them, I have to do a soft-reset to get them to kick in, if its the bluetooth code issue, how do I remove BLUETOOTH ALTOGETHER??? even though I have a headset, the reception is terrible and I'm not going to solder an extra wire and drill a hole like some others have, god I hate O2 for this piece of junk!
and yes I am on Radio ROM 1.13.00
AND i hear 1.42.00 is worse than 1.40 I-mate which I am using.
The same fault as mine......
MegaHz,
It sounds like the same fault that I have got.
If you are running anything with sound (Tomtom, Media Player, Ring tone etc) it will be running sweet through the speaker, and then all of a sudden it will just stop (this is not the unidirection problem - but you get the same effect when in call - ie the caller can here you, but you can't hear them).
On my Blue Angel, if you press your ear really close to the speaker, you can faintly hear the sound/bleeps. The sound will come back without any warning and will drop off again at will...........
I did drop it, so I took it apart to check for damage.... I did earth myself but could of zapped one of the internal organs with some static.........
I don't have any of the problem mentioned. I'm running on 1.42 ROM, and the problems are mainly with the Wifi. It takes more time to connect to an AP, sometimes it doesn't like turning on thus requiring a soft-reset, and sometimes like all ROMs, the icon at the top starts flashing and the screen's backlight flashes on and off and I am forced to soft-reset.
I have got this weird problem with my Qtek 9090, I can’t hear a thing from the speaker except incoming calls??? And there’s no sound when I pick up and no one hear me on the other side unless I use the headset or the Bluetooth headset, everything works great then even playing music !??
I tried with few other rom, but no success! I even tried with WM5
Could this have anything with the headset plug? Cuse when the headset is plugged (in normal case) you can only hear incoming calls from the phone!
Remove your bluetooth profile(s), and do a soft reset.
I have the same problem after I used bluetooth.
Guest said:
Remove your bluetooth profile(s), and do a soft reset.
I have the same problem after I used bluetooth.
Click to expand...
Click to collapse
Not even flashing with new rom is helping as I wrote
FFVIII said:
Guest said:
Remove your bluetooth profile(s), and do a soft reset.
I have the same problem after I used bluetooth.
Click to expand...
Click to collapse
Not even flashing with new rom is helping as I wrote
Click to expand...
Click to collapse
What has flashing with a new rom have to do with removing your bluetooth profile?
Guest said:
FFVIII said:
Guest said:
Remove your bluetooth profile(s), and do a soft reset.
I have the same problem after I used bluetooth.
Click to expand...
Click to collapse
Not even flashing with new rom is helping as I wrote
Click to expand...
Click to collapse
What has flashing with a new rom have to do with removing your bluetooth profile?
Click to expand...
Click to collapse
dude, thanks for trying to help, but you should know better. flashing with a new rom erase everything including the the BT profile. I still think the problem is the headset jack.
And there’s no sound when I pick up and no one hear me on the other side unless I use the headset or the Bluetooth headset, everything works great then even playing music !??
Click to expand...
Click to collapse
This is telling me that you DID install the bluetooth again, and so you have a bluetooth profile, what is causing the no sound problem!
I have exactly the same problem as you.. When I remove the bluetooth profile all is working fine again.. that is.. untill I set it up again, and use it.. Than the SAME problem is back.
thank alot , but still got the problem even with the BT-profile removed, I have to use the wired headset to be able to hear anything
Problem Solved :lol: :lol: :lol:
I Opened the damn thing and took a look at the 2,5mm jack and guess what, it was broken ( I remember dropping the phone once for a week ago), I just removed it ( I don’t use the headset but I need the speaker), and everything is loud and clear now,
and with a Sprite Backup file I’m back now :twisted:
!!!?
I have such problem, but I think it really barbarian means of solving problem.
Is there any cleaner way?
Re: !!!?
hishnik said:
I have such problem, but I think it really barbarian means of solving problem.
Is there any cleaner way?
Click to expand...
Click to collapse
I read in another post somewhere that there is a microswitch in/near the headphone jack that switches off the sound to the speaker. Apparently, if it sticks, you poke a paper clip in and twiddle it about and you'll free it.
no sound form jasjar
having same problem. poked around with paperclip and all that, but still no sound. dont need headphone jack because hoping to use latest a2dp hack form latest rom for jasjar to be able to use BT headset. will removing headphone jack affect using BT headphones? need external sound.
I also have a similar problem - when in phone mode, other side can hear me but i cannot hear them, if i plug a headset with microphone the other side hear me and i also have sound from other side.
if i unplug the headset, i cannot hear the other side but the other side can hear me.
are there microswitches inside the headset plug for both microphone and speaker (two microswitches) ?
thanks, yol.
just got my jasjar back after having cracked lcd and headphone jack replaced. sent to http://www.pocketpctechs.com out of california as suggested by very helpful user on this site. cost me around $20 dollars and took only a day to fix. works fine now!
My O2 XDA IIs is behaving rater unusally. For a while I've had the problem that many people have reported where I can hear nothing during a call but the other person can hear me. This could be remedied by a soft reset. However now, no amount of resets seem to fix the problem.
The baffling thing is though that the speaker hardware would appear to be working as MediaPlayer still plays music out of it and the phone still rings etc. However no sound what so ever comes through the 2.5mm socket now, from either a call or from MediaPlayer.
What on earth can I do to fix it?
My O2 XDA IIs is behaving rater unusally. For a while I've had the problem that many people have reported where I can hear nothing during a call but the other person can hear me. This could be remedied by a soft reset. However now, no amount of resets seem to fix the problem.
The baffling thing is though that the speaker hardware would appear to be working as MediaPlayer still plays music out of it and the phone still rings etc. However no sound what so ever comes through the 2.5mm socket now, from either a call or from MediaPlayer.
What on earth can I do to fix it?
Guys, are your problem similar to mine? My problem is that the speaker is not working even though playing mp3. I thought it was radio problem, so flashing new rom also doesnt help. It is really the headphone jack cause the problem? When i flash to new rom, the speaker works, but after the auto config, the speaker doesnt even sound.
Please advise me on this. Thank in advance
Guys, are your problem similar to mine? My problem is that the speaker is not working even though playing mp3. I thought it was radio problem, so flashing new rom also doesnt help. It is really the headphone jack cause the problem? When i flash to new rom, the speaker works, but after the auto config, the speaker doesnt even sound.
Please advise me on this. Thank in advance
HI EVERYONE
I HAVE T-MOBILE MDA PRO
I UPGRADED TO WINDOWS MOBILE 6 PROFESSIONAL WITH
1933.18533_Thingonaspring.ROM.v3.2
AFTER THE UPGRADE I LOST SOUND DURING THE PHONECALL
I CANNOT HERAR ANYTHING NOT THE PERSON ON THE OTHER SIDE CAN HEAR ANYTHING ALL WE HEAR IS COMPLETE SILENCE
THE PHONE WORKS FINE BUT NO SOUND
i ALSO TRIED SEARCHING THE FORUM
ONE OF THE POST ADVISED TO DOWNGRADE TO THE ORIGINAL ROM AND RADIO
I DID THAT DINT WORK
NOW I HAVE A PDA W/O A PHONE
SOMEONE PLEASE HELP ME
THANKS
some one please help me
someone please tell me what can i do to get back my phone up and running
please help
mihirparikh said:
someone please tell me what can i do to get back my phone up and running
please help
Click to expand...
Click to collapse
have you tried to raise the volume in-call?
I mean when you are calling just slide the switch on the side of your pda (above the button with the lightbulb) upwards, maybe your volume is just set down to nothing
3.5 Jack damaged
this model and the s200 has a problem with the 3.5 jack for earspeakers, I mean, you have to open the equipment and fix the 3.5 jack, this problem happend in my v1640 and I fix it this way.
Regards
mochoab said:
this model and the s200 has a problem with the 3.5 jack for earspeakers, I mean, you have to open the equipment and fix the 3.5 jack, this problem happend in my v1640 and I fix it this way.
Regards
Click to expand...
Click to collapse
I jiggered a jack in the hole and got my sound working. Of course, my problem came into being after I hooked up my Universal to the tape adapter of my Bronco on the way back from school one day. So now I have no plans to use the audio jack unless absolutely necessary.