I've been encountering this error for some time....
When I leave the phone unused for sometime and it enters sleep mode, after a few minutes I try to turn it on and it won't start.
Can anyone help me...I've checked all settings (buttons, power, screen, etc.) but it didn't help.
Everytime I need to softreset to be able to use the phone again.
Thanks a lot for your help
have the same problem, i have used all new AKU 3.2 ROMS, also original for SPV M5000 for my Uni, have used almost all radios (10.3 and higher), but the problem persist
any help please?
thanx
Related
I'm using a Titan 6800 unlocked w/ olipro SPL 2.4
To exit bootloader I flashed the Titan Radio 3.27.20
So then it loads up and freezes, because the stock ROM isn't compatible with the new Radio. I've overcome this before by entering bootloader and Flashing a WM6.1 GPS enabled ROM by either DCD 3.0.4 or Key's v1.3.2 cleaned.
Except this time, my PC gave me greif with active sync, and half an hour later when I finally tried running enter bootloader my Titan 6800 went out.
Soft reset will only make it vibrate as if it's rebooting but the screen never comes on and it seems to never load, "camera + ok + sr" does the same thing, hr does the same thing, battery out and back in does the same thing, and obviously active sync won't recoqnize it anymore.
Basically I can't get it to respond beyond reboot!
Any help would be greatly appreciated
HI all,
I'm having some fun and games with my Orbit today.
I previously had an old version of black & Blue on there. SO today decided to update to have a go with some manilla based ROMS.
First I Tried YuE_v11.3_3.15.20755_Lite_M2D_WWE
Which seemed to work ok but after a while applications were being very slow.
So then I tried to reflash oop, but that seemed to fail.
I Tried to flash love, but it wasn't ever getting to the progress indicator on flashing, so did an SD flash of YuE which worked.
So then tried to flash Love from that minimal YUE and the device is being really slow, like gets to the calibration and takes about 5 mins to swap between screens.
What's the best way to totally clear down the rom and start again on this?
Thanks
I've now flashed the Official UK O2 WM6 ROM and still having problems. Flashed succesfully, but when it boots up, it just sits on the "Windows Mobile" screen and beeps a bit
Current State after O2 flash :
IPL : 3.04.0001
SPL : 3.04.0000
GSM : 03.06.90
OS 3.4.0.0
Any help gratefully appreciated.
Thanks
Hard reset the device, and while you're in the config wizard, plug in your device and flash to new rom. That way it's completely formatted and you'll have a fresh new install... hope it works mate
I did a hard reset, still no joy, hangs on the welcome to windows screen
I can access the Bootloader, but can't find a way to flash a rom from there, all seem to want it done once you've made an activesync connetion
flash YUE back via SD card flashing
I already tried that, flashes fine, but becomes unresponsive soon after
have tried flashing O2 WM5 + WM6 from SD, but still no joy.
It just flashes, loads up WM(5/6) then hangs there, beeping sometimes. Pressing the green button brings up the calibration screen. I sometimes see bits of apps, today screen, but that's about it, it's generally unresponsive.
Any suggestions?
ta
A little update incase someone can help?
I left the battery out of the phone all night last night, and this morning the phone worked great.. for about 2 hours, then it froze. I hard reset, and it's back to freezing after OS loading now
What's up if you remove your MicroSD card ?
That makes no diff, i've tried flashing with + without the SD card (it's currently out), flashing from windows + flashing from microSD, all ends up the same way, with an unresponsive device once the OS boots.
Dear all,
I need help in repairing my Asus p525. I was trying to flash it to WM 6.1, but suddenly update failed. After that i started getting asus Blue Screen, and nothing more. I cannot hard reset, neither turn on the PDA. When I take out the battery, I can, by pressing CAM REC JOY and SOFT RESET button to get to USB loader.
I used USB loader and reinstalled my ROM and Boot Loader to Official Release of Asus. But this didnt help and I still get only Blue Screen, and after that nothing - unless I take out my battery for a while and return it.
Can anyone help me with this problem ?!
Greetings
New thing
Last night I took my battery out of the phone. Today I dont even have ASUS BLue Screen, but still i can, while holding the buttons, on reset (inserting the battery) to go into FORCE MODE.
Anyone know what to do ??
Today I reflashed with new roms, but it just dont work.
Greetings
I realised now, that when I charge the battery FULL, the phone starts working ?! First i have problem to calibrate the screen, and later on the OS start to work, and everything seems fine ?! But it resets, block..... hardware thing ?
hi
can anyone help me, i flashed my spv m700 with a new rom, the programme crashed during upload and instead off the system rebooting to my original rom. it now wont boot up, it gives me the option to soft reset and hard reset, but the screen wont come on, the green light on the top just stays on constant and the screen does not come back up, please help
Just use the "Search" take a look at this thread http://forum.xda-developers.com/showthread.php?t=308691 i think it will be helpful, once i've had the same problem and used the splxploit mentioned there and everything was just fine! Hope it helps , Good luck and post a reply if it does or does not!
Hi,
P.S: I have read almost every post and thered and wiki and what ever, nothing worked for me, need advice.
My ppc is i-mate jasjam herm100
ipl-1.00
spl-1.04
it was running just fine, then out of the blue, it hang i reset the phone with the styles as I was unable to shut it down due to the hang, once restarted it is stuck on the tri-color screen.
tried to restore defaults, using the front 2 softkeys and the reset with the styles, then i confirmed the restore pressing the 'R' button it took 1 sec and told me it is restored, tried to restart the phone same tri-color screen, so I have been every where forums wiki post to solve this issue but was unable, I don't need to be WM6 or any thing I just need my phone working even if running WM3 "kidding" all what I want is the phone life and kicking again, if any one can help me here, it is appriciated alot.
Thank you.