Anyone had any luck(short of breaking it) on removing the little rubber cover over the usb port? It is constantly getting in the way.
It looks like you would have to take 4 screws out when you take the battery cover off. But I don't have that kind of screw driver.
It looks like it is actually 6 screws. You have to remove the 2 near the top that are covered by those little rubber plugs. Unfortunately, when I got to that step I found out that there is one of those water detecting dots covering the head of the top right screw. I didn't want to break it and void my warranty.
Related
Ok everybody, I have taken my PDA2K apart & fixed the wobbly screen problem, First things first:
1. get a sharp knife & carefully slide it under the VOID sticker moving upwards very slowly,& you should be able to remove the sticker in one peice,I have done 7 units ok so far.
2. remove three black screws from the battery compartment,& the silver countersunk screw from underneath the now removed VOID sticker,
Then the 2 countersunk screws from the top sides of the PDA2K,now the rear cover can be removed.
3.Three screws hold down the main PCB,looking from bottom of unit,one screw very top right corner of PCB.One screw Very top left corner of PCB.
& one screw half way down on right side near the ribbon cable for the key board.Then remove the yellow tape over the keyboard ribbon cable,Then lift the black clamp on the ribbon cable connector upwards,and put a round diameter screwdriver under the ribbon cable & pull outwards in a straight direction.
4. Extend the screen fully open & carfully lift the PCB up from the left side (OPPOSITE) the keyboard ribbon cable connector,& hold it slightly up as you carfully slide a blunt flat Knife under the 2 ribbon cables for the display.They will just pop off with minimal force.
5. Pull out the vibration motor & microphone from their casing slots (NOT PCB CONNECTORS) & place the main PCB in a safe place.
6. Looking at the back of the front section you should see 2 screws through slots in the back casing,& 2 at the top rear of the display.remove these & lift the display up from the bottom,carefully guiding the 2 display ribbon cables through the slot.
7. You will now be able to see the sliding plate edges & the two white peices of plastic at the bottom of the slider,These plastic peices need to come off in order to pull the slider plate up further and off the upper casing.what ever you do DO NOT lever the slider plate up with a screwdriver or the brittle moulded painted clamps will snap.if one does its not the end of the world,the slider plate side can be re-adjusted slighty to compensate.
8. With the slider plate in your hand you need to get a flat (NON SERATED) pair of pliers & carefully & very slightly move the edges of the slider plate outwards on each end so they are not going straight up.ie Looking at the plate from the bottom and flat in your hand the plate will look like a U shape,bend the ends out slightly away from each other so they sit against the slider clamps with more resistance,Be carefull not to over do it or you will end up with a very stiff display,
9. Assembly is a reversal of taking apart but be carefull to guide the display ribbons into the top hole of the slider plate,in its open position,
& make sure to tuck the vibrator motor wiring under the PCB before putting the rear casing on.Also hold the volume slider in the middle position as the rear casing is lowered into position.Remember DON'T FORCE ANYTHING or your beloved device will get damaged .
DONT forget to put the yellow tape on the keyboard ribbon cable & the VOID Sticker back on the silver screw & you will still have your warranty.
I have done this mod on a few units with success every time,& this should have been done in the factory,I find it a shame that comparing this unit to the XDA1 its not got the build quality that the XDA1 has and for £580 its a shame that the hardware is not up to the quality of the software features.
Saying that,I can now hold my PDA2K in my hands without its display moving sideways & it makes me feel im now holding a solid peice of kit worthy of £580.
PS I still have 2 brand new XDA1's for sale & one second hand one ive been using for the last year, 07958031182 Thanks & good luck........... :lol:
hi
any1 who has opened the pda2k .. is the camera soldered onto the mother board or is it only plugged in>???
thanks
Hi the camera is only plugged in,but you have to remove the wifi antenna to remove fom the motherboard.hope this helps.............
I was trying to fix one problem and ended up making another.. Anyone know if the plastic piece that has the latch on the mother board (zif connector maybe?) that holds the ribbon for the charger can be replaced? The tablet still works but I can now no longer charge it or plug it into the computer. If its not possible to fix that then is wireless charging possible? I know I still wouldn't be able to sync with the computer but I would be good with that as long as I can charge it.
Below is a pic of what im talking about
Erm ouch, im no electrician but i think you may have ****ed it...
Right well best thing i can suggest is that a Samsung repair agent might have to look at it.
(Or you could find the pieces on the Interwebs for it)
I've done this a few times to laptop motherboards years ago. Just use some high quality tape to make sure the connection is complete. If it comes undone you'll just have to redo it, but if you use good tape you shouldn't have to. Definitely not the end of the world, they're just cheap plastic clips.
wbaner said:
I was trying to fix one problem and ended up making another.. Anyone know if the plastic piece that has the latch on the mother board (zif connector maybe?) that holds the ribbon for the charger can be replaced? The tablet still works but I can now no longer charge it or plug it into the computer. If its not possible to fix that then is wireless charging possible? I know I still wouldn't be able to sync with the computer but I would be good with that as long as I can charge it.
Below is a pic of what im talking about
Click to expand...
Click to collapse
Even u manage to wireless charge it and how is tablet suppose to get power from the battery?
The zif connector is cheap, but alot hasssle to remove the board and dont know if the EMI shield is soldered into the board or with screw like Note 10.1 had.
Hard to see from this disassemble video. (scroll to end)
If u got good soldering skills and can find the zif connector part. Then its worth a try.
https://www.youtube.com/watch?v=zOzrRu8PB2Y&list=WL&index=3
Backyard repairs
All you need to do is achieve 2 things.
1. Locate it so that the cable contacts line up with the pins in the connector.
2. Apply pressure on the cable so it has good contact.
Using your fingers put pressur on it and check that its charging when plugged into the usb.
Then tape it in position.
To get the pressure on it, cut a piece of plastic and tape it on the area where it contacts the pins.
Then cut some rubber so that its thick enough such that it puts pressure on that plastic bit when its put back together.
Tape that rubber in position and put cover back on.
Should last, but if not just redo it again and get the rubber thickness right.
warboat said:
All you need to do is achieve 2 things.
1. Locate it so that the cable contacts line up with the pins in the connector.
2. Apply pressure on the cable so it has good contact.
Using your fingers put pressur on it and check that its charging when plugged into the usb.
Then tape it in position.
To get the pressure on it, cut a piece of plastic and tape it on the area where it contacts the pins.
Then cut some rubber so that its thick enough such that it puts pressure on that plastic bit when its put back together.
Tape that rubber in position and put cover back on.
Should last, but if not just redo it again and get the rubber thickness right.
Click to expand...
Click to collapse
haha.. I was messing around and figured this out.. only I put a piece of cardboard box on it and taped it.. put the cover back on it and its charging again.
wbaner said:
haha.. I was messing around and figured this out.. only I put a piece of cardboard box on it and taped it.. put the cover back on it and its charging again.
Click to expand...
Click to collapse
Well it says charging but the percent is still going down?
Going to power off the tablet and see what happens.. ugh
Also watched the video that was posted and I cant really tell much from the video.. if you can just buy one of those sockets and have it put on the motherboard then I will go that route.
after the first charge my rubber cover for the battery looks bent. i guess i pried it out and to the left instead of backwards towards the strap and that's how this happened. i have big fingers and it wasn't easy for me to pry it open at all. i tried to bend it back the other direction and it almost sits flush now. it doesn't appear the seal around the actual micro-usb port is damaged, just the outer rim standing up you see. wondering if this is normal, and if it will have any negative effects when it comes to waterproofing.
Yes...exactly the same.
Doesn't look right
tuffluck said:
after the first charge my rubber cover for the battery looks bent. i guess i pried it out and to the left instead of backwards towards the strap and that's how this happened. i have big fingers and it wasn't easy for me to pry it open at all. i tried to bend it back the other direction and it almost sits flush now. it doesn't appear the seal around the actual micro-usb port is damaged, just the outer rim standing up you see. wondering if this is normal, and if it will have any negative effects when it comes to waterproofing.
Click to expand...
Click to collapse
It looks to me like your usb port cover is damaged. I can't believe that pulling it out on the left side instead of the back would bend it permanently like that. I would guess it's defective. If the watch is new and still under warranty, I would probably try to exchange it for another.
I've had my SW3 for about 7 months and have taken the usb rubber cover off many times to charge the watch. So far, it has held up well and still looks new. Click on the below imgur link to see a couple of pics of my SW3 compared to yours.
http://imgur.com/a/Es97z
anyone else? i googled pics of this and all the pictures showed it to be bent the same as mine and onatepp
maybe even helpful if onatepp or others have tried this in the water with no damage...
No need to worry in my opinion. Mine looks the same and I bought mine 7 months ago and several times per week I am taking a shower with it after workout.... I do not think you need a perfect seal to have a waterproof watch, the usb port would not let the moisture into the main body. The rubber cover mainly serves to prevent electrical issues when charging, and maybe corrosion.
You can try with yours
Ok, getting serious, I do not think there is an issue with water. The USB port is sealed.
Will not leak water on the inside. The rubber is meant not to let dust/rubbish inside.
tuffluck said:
anyone else? i googled pics of this and all the pictures showed it to be bent the same as mine and onatepp
maybe even helpful if onatepp or others have tried this in the water with no damage...
Click to expand...
Click to collapse
Hi all,
i'm very disappointed because i'm just breaking my screen when my zenfone fall of 60cm.
LCD is ok but screen is dead
On ebay i know you can find only the screen with kit, and LCD + screen
Does any one have advice for replacing the screen or screen + lcd? (video or pictures).
Asus France ask me 180€ to change that
thank for your help...
pulesky said:
Hi all,
i'm very disappointed because i'm just breaking my screen when my zenfone fall of 60cm.
LCD is ok but screen is dead
On ebay i know you can find only the screen with kit, and LCD + screen
Does any one have advice for replacing the screen or screen + lcd? (video or pictures).
Asus France ask me 180€ to change that
thank for your help...
Click to expand...
Click to collapse
Seems pretty easy, please check these videos:
https://www.youtube.com/watch?v=qMIivqu6XJY
https://www.youtube.com/watch?v=v4HZt3Aadsc
I ordered a screen replacement on AliExpress. I've only cracked the glass on my phone, but I don't think it's possible to replace the glass on its own. (Unless you have the hands of a neurosurgeon and special equipment.)
Tried changing screen today, but it requires a complete disassemble of the unit. I managed to remove the back and disconnect the components, however I wasn't able to remove the battery since it seems to be glued (?) in place on one side. I even tried using quite a bit of force, but eventually I chickened out since the battery started bending. I have no idea how they do it so easily in the video. If anyone here has managed this disassemble I'd be very interested in getting some details.
dodongobongo said:
I ordered a screen replacement on AliExpress. I've only cracked the glass on my phone, but I don't think it's possible to replace the glass on its own. (Unless you have the hands of a neurosurgeon and special equipment.)
Tried changing screen today, but it requires a complete disassemble of the unit. I managed to remove the back and disconnect the components, however I wasn't able to remove the battery since it seems to be glued (?) in place on one side. I even tried using quite a bit of force, but eventually I chickened out since the battery started bending. I have no idea how they do it so easily in the video. If anyone here has managed this disassemble I'd be very interested in getting some details.
Click to expand...
Click to collapse
Try using a hair dryer on the battery for a minute, but keep moving the hair dryer up and down, to spread the heat all over, this should make the glue soft enough to make it easier to peel the battery off.
Finally managed to replace the screen. This one was really difficult to repair compared to the previous phones I've worked on, but maybe in part because there are no complete instructions out there yet. Lots of glue and tape holding it all together.
The battery isn't really glued, but rather held down by some sticky plastic. (Kinda like chewing gum.) I don't think heating will help here. I used a long, flat plastic object to reach underneath and loosen it from the battery.
I forgot to take pictures, but here are the steps I took. You can find some photos for the first half of the procedure.
Remove 14 screws from the back cover
Carefully remove back plastic cover (double sided tape on center)
Unplug the three connectors going to the top PCB/SoC (these are screen, SIM/SD and battery)
Remove speaker (black piece at the bottom, nothing is holding it in place)
Remove bottom PCB: flip up the little black switch to loosen the connector cable next to the battery, then unplug the wire going to the top PCB, then you can remove it. Vibrator piece doesn't need to be unplugged.
Battery can now be removed, but is as mentioned fastened very well. Try to pull it up on the left side to reach under it.
Unplug digitizer connector on the left side of the top PCB. Just peel off the yellow take and pull it out.
Peel loose the part of the metallic shielding that fastened the top PCB to the surface under where the battery was.
Top PCB can now be removed, start from right side.
Peel off the little "sticker" the digitizer connector goes to. This is probably part of what you're replacing, so it doesn't matter if you destroy it in the process. Otherwise try heating it.
Screen can finally be removed. It's removed from the front of the phone, same as for Zenfone 5. Start at the bottom. It's fastened with glue along all sides. If you're hoping not to ruin the LCD while removing the screen you will probably need a heat gun and extreme patience.
dodongobongo said:
Finally managed to replace the screen. This one was really difficult to repair compared to the previous phones I've worked on, but maybe in part because there are no complete instructions out there yet. Lots of glue and tape holding it all together.
The battery isn't really glued, but rather held down by some sticky plastic. (Kinda like chewing gum.) I don't think heating will help here. I used a long, flat plastic object to reach underneath and loosen it from the battery.
I forgot to take pictures, but here are the steps I took. You can find some photos for the first half of the procedure.
Remove 14 screws from the back cover
Carefully remove back plastic cover (double sided tape on center)
Unplug the three connectors going to the top PCB/SoC (these are screen, SIM/SD and battery)
Remove speaker (black piece at the bottom, nothing is holding it in place)
Remove bottom PCB: flip up the little black switch to loosen the connector cable next to the battery, then unplug the wire going to the top PCB, then you can remove it. Vibrator piece doesn't need to be unplugged.
Battery can now be removed, but is as mentioned fastened very well. Try to pull it up on the left side to reach under it.
Unplug digitizer connector on the left side of the top PCB. Just peel off the yellow take and pull it out.
Peel loose the part of the metallic shielding that fastened the top PCB to the surface under where the battery was.
Top PCB can now be removed, start from right side.
Peel off the little "sticker" the digitizer connector goes to. This is probably part of what you're replacing, so it doesn't matter if you destroy it in the process. Otherwise try heating it.
Screen can finally be removed. It's removed from the front of the phone, same as for Zenfone 5. Start at the bottom. It's fastened with glue along all sides. If you're hoping not to ruin the LCD while removing the screen you will probably need a heat gun and extreme patience.
Click to expand...
Click to collapse
Just cracked my phone. :crying:Thanks for the instructions. Before I decide to do this, are any of the adhesives necessary to put the phone back together?
Yes, order some double-tape for cellphones.
Glad I'm not the only one that succeded althought I scrapped the battery in my case .
I followed mostly the same steps but for anyone that want some pictures, I posted them in another thread
http://forum.xda-developers.com/zenfone2/help/q-lcd-replacement-procedure-t3135165
Can asus ze550ml screen will fit to ze550kl model
@Ptselv: probably best to start a new thread rather than hijack one that is several months old.
And to answer your question: No, a ZE550ML screen will not fit a ZE550KL phone. My suggestion: search AliExpress.com for "ze551kl digitizer" and you'll be likely to find what you need.
My Zenfone 2 screen broke as you see in the attachment so I ordered a new one and 'am ready to replace it
the only thing I worry about is the proper way to remove the battery.
There's a adhesive tape underneath it that holds it in place but in all tutorials I've search about they dont mention this at all.
There two methods of removing the battery :
1.By using a metal pry tool by gently lifting the battery up BUT the set of tools that came with my display doesn have any
(In case you're wondering here is the display I've bought with the set of tools as an extra gift )
https://www.aliexpress.com/item/Original-High-Quality-Touch-Screen-and-LCD-Display-Digitizer-Assembly-TP-For-Asus-zenfone-2-Zenfone2/32637537543.html?spm=2114.01010208.3.1.Hj6See&ws_ab_test=searchweb0_0,searchweb201602_5_10065_10068_10000009_10084_10083_10080_10082_10081_10060_10062_10056_10055_10054_10059_10099_10078_10079_10000012_10103_10073_10102_10000015_10096_10052_10053_10050_10107_10051_10106,searchweb201603_10,afswitch_5,single_sort_0_total_tranpro_desc&btsid=973e8fec-268f-429d-9ffd-7590578fe972
2.By removing the adheasive completely by strecting it from the pull tab
So my question is:
how to remove the battery WITHOUT damage it, how to remove it without the metal pry tool,and if I remove the tape is this gonna damage the battery in the near future?
This is how I removed the battery when I changed my brother's broken LCD:
remove as many components as possible from the phone;
gently heat the front of the phone (i.e. blow heat on the battery from the glass side of the LCD) with a hair dryer;
slip a thin/blade-type pry tool, small flat head screwdriver, or wall scraper under the battery and slowly/gently start lifting the battery away from the housing. Do this a little at a time and re-heat if necessary until the battery lifts away from the housing.
I don't recommend pulling on the tab.