Hi all,
after an error during a rom upgrade therefore a reset I got only serial and ver1.00 written on.
Doing the upgrade procedure (power-lamp-reset) -> usb to pc -> UpgradeUt.exe I get no connection established between pc and pda.
Unknown USB device (bold) on pc when pda restarts and should be ready for the download but no communication happened between devices.
Could you help me before I bin it ???
thanks in advance,
fabio
italy
Wrong unlock
After executing MaUpgradeUt_noID.exe in the screens appears Serial V1.00 and I cannot make any softreset or hardreset, can anyone help me???
Related
Hi,
I just started with the ROM upgrade of my I-mate Pocket PC to 1.72.00wwe (obtained from the I-mate website) when my phone switched off. Now it only has (at the top) "Serial" and (at the bottom) "v1.06". No matter what I do - soft or hard reset nothing happens, obviously the power button also doesn't function. On my PC desktop I got the message that I need to reset my phone and re-connect.... can't get my phone going, so here I am.
The solution to my problem is (hopefully) simple ? I will really appreciate if you could help me with this ?
not a problem hopefully....u just made HimaClearJumpCode.exe run on ur device(this file exists in ur upgrade folder),and now ur stuck in the bootloader mode....
do the following:
1-hard reset ur device(it wont boot,off course)...
2-put it in the cradle,u should see that ur XP has found a new hardware(if it doesn't,change the USB port)
3-now run the himaupgradeUt.exe.
Now in case(just in case),those procedures didn't work,go to plan B.. :wink:
1-take the battery off ur Himalaya.
2-leave ur device for 12hours(it won't need all that time,but to be on the safe side,u know... :wink: ) without battery,so that backup battery drains...
3-put back the battery,recharge and enter the OS(this option wont work if u have erased the ROM)
4-rerun the upgrade...
good luck.....
RAGO :lol:
Hi
OK, what happens if the ROM is erased.... (judging by the fact that nothing happens when I put it in the cradle - with power on the cradle) ?
My phone was off for about 12-hours - blank screen when I got here this morning.
If I put it in the cradle (and after changing between all the available USB ports on my PC) the PC doesn't detect it - ActiveSync doesn't connect to the phone at all... Note : I have power on the cradle, and it's been a hour now - still just "USB" "v1.06" (or "Serial" if I take it out of the cradle).
:?:
so it is connected!!!!!!!!
since ur serial on the top of ur screen changes to USB when u put it in cradle,then it's connected.... :wink:
now just run the HimaUpgradeUt.exe in the folder that contains the NK.nbf file(32MB,it's the ROM),and it should start the upgrade....
be sure the NK.nbf is a Himalaya ROM....
good luck...
RAGO :lol:
Hi,
Thanks, did it just after posting my reply and everything worked out fine. Note, I just ran the ROM upgrade file (not HimaUpgradeUT), which I got from the clubimate webste.
Thanks, once again for helping me with this one.
Himalaya pocket pc - screen frozen on bootloader
Hi,
My problem is the same - but the difference is that whenever i run the himaupgradeut i get a connection error saying that the PC cannot identify the cradle as connected.
What should I do now?
After a interruptus ROM upgrade my s200 d'ont start . after the HTC i have a white screen but not more.
The activesync don't connect and i can't put the ROM another time.
I obtain the multicoloured screen with usb in the left botton.
Please, could anybody help me to update the rom in this situation , mayby without activesync ??
Regards.
Edit/Delete Message
i sugest you ask here
http://forum.xda-developers.com/forumdisplay.php?f=293
as more % of the readers of that forum have the same device as
you then this forum
All is OK , Thank's
Yes thank's, i found a ROM that don't need activesync , after that changing that rom by my rom and at the moment my s200 y ok.
Thank's.
tehe same problem
hi
i have a qtek 8310 and have the same problem that u, could u tell me what kind of rom does not need activesync, please?
thanks a lot
Indeed, I have the same problem with my S200, please explain what you did to fix your phone!
For those interrested: I've found the following text in the readme file of the regular ROM updaters (RUU_Prophet_2151327_21513121_021921_DOP_ASIA_WWE_Ship-NoVendorID in this case):
8. Q: I use RUU to update and failed, and my device always boots in three-color mode and cannot enter CE OS anymore, what should I do now?
A: If the update process has failed, you will see that your device will always boot in three-color mode. It’s normal and can be recovered. Please follow the instructions below to reset your device and to establish a connection with the computer.
1. Disconnect your PDA Phone from the USB cradle/cable.
2. Reset your PDA Phone.
3. Reconnect your PDA Phone to the USB cradle/cable.
4. Check that the communication cradle/cable is connected properly.
5. Return to the ROM Update Utility.
Note: You should ignore the ActiveSync connection.
Hello guys,
I have an I-mate JasJam .. a week ago i followed mrvanx's guide to successfully upgrade to schaps 3.30c . just two days ago my windows xp pro stopped recognizing my phone, it says generic USb in the device manager and sometimes it says HTC USB SYNC but with the exclamation mark .
I only managed to connect my phone with activesync 4.5 if "Enable advanced network functionality" IS ticked . and therefore windows recognize my phone as a Network adapter . And i can't flash my phone anymore as windows loses connection to the phone at the final step leaving the phone at the tri color screen
Tried and changed the cable but same problem .
Tried to use the microSD card flash technique to upgrade to schap's 3.54b and copied+renamed to HERMIMG.nbh to the root of my storage card but when i enter the bootloader mode i also end up with the tri color screen and the phone does nothing .
Been reading all over to solve this for the past 3 days but i can't figure out where the problem is
Is it possible that my phone got defected ?
here are some info from my phone :
ROM version : Schap's 3.30c
ROM date : 05/15/07
Radio version : 1.41.00.10
Protocol version : 32.74.7020.18H
Herm100
SPL-2.10.olipro
thanks a lot
hi,
following tries:
-unselect/deactivate "Enable advanced network functionality"
-turn your Computer off and Phone on
-connect Phone with Computer
-switch PC on
Is a stable connection between phone and pc?
You can flash much with the attitude sspl in RUU Wapper.
wfg
S64
I had some kind of this problem also. Try this one:
http://forum.xda-developers.com/showthread.php?t=332565
Hello all!
I've purchased O2 XDA Zinc in Arabian. I'm living in Russia now.
When I open the box, get the PDA and turn them on I've got screen like this:
mars II eboot ver......
h/w version v1.4
******** usb loader ***********
diskonchip g4 128mb
start downloading image...
please plug-in usb cable...
And that's all... Now I can't go to Arabian to change my PDA and there is no service center that can fix it in Russia
I tried soft and hard reset and no effect.
When I connect PDA to PC the new hardware "Asus USB sync" appear in system, but Active Sync does not recognise them (I have 4.5 version).
All o2 zinc upgrade software are working with active sync and available os and i can't use them.
I've extracted binary filles from update exe, larger of it i've rename to MarsII_G4.ABI and put it on SD. But after insterting card and restarting nothing happens.
I also have some knowledge of elelectronic.
So, please help, how can I fix my PDA?
Thank you in advise!
ok fer
find another ppc first
find a dos app and rename it to devicespy.exe and make it readonly
transfer it to windows directory of other ppc and plug it to pc via mini usb and activesync 4.5
download and run any zinc rom from seeo2
if you did it well the upgrade software cant recognize the device type so continue update progres until your ppc get reset.
replace that ppc with your zinc and update will continue to end and your zinc will be fin.
choose any lang you wish.
You'd better visit www.seeO2.com
and register with your IMEI.
Then you can download WM5 or WM6 official rom.
Hope this can help
Yeaaa!!
It's really working!!
Thank you!
I've recovered my device by using this method.
O2 XDA Zinc. Please, help
Hi where can I get dos app file??
hi all......
i do really need help for reviving my dead o2 zinc.
it is suddenly dead wen connected to notebook via activesync.
yes.. it is SUDDENLY DEAD.
i'm doing nothing.
i have been trying to entering bootloader (by pressing right d-pad plus soft reset), but the bootloader doesn't show up.
doing hard reset, but nothing happen. still dead.
one thing that works is...
there is blinking orange LED when i connected zinc with wall charger (without battery inserted)
and there is orange LED (showing up about 3-5 secs) when i connected zinc with wall charger (with battery inserted)
anyone can help me solving this?
how bout using mtty?
anyone knows?
Hello,
I connect my qtek with pc. I tried to install wwe rom - from german to english. I ws downloaded english rom but cant install coz i have problem with COUNTRY ERROR -ERROR 120 atfer that i install in qtek "MaUpgradeUt_noID".exe and after that my qtek go to hell.
when i done hard reset on the screen write only: Serial and v1.00!!!!
..............qtek is dead...................
PLzzzz people help meeeeeeeeee
what can i do now for repair my qtek?????
p.s. srry for my bad english
Kind regards
Your Uni still alive
Try to download "Exit Bootloader.exe" from wiki, conect the uni to USB and Run the applcation...
If you uni is death when the Bootloader is lost. I brick my Jasjar when the Bootloader was gone, dont worry Try to read more in the forum Universal WM6.
AIN1 said:
Try to download "Exit Bootloader.exe" from wiki, conect the uni to USB and Run the applcation...
If you uni is death when the Bootloader is lost. I brick my Jasjar when the Bootloader was gone, dont worry Try to read more in the forum Universal WM6.
Click to expand...
Click to collapse
Hi AIN,
Thnks Mucho Mucho!
My Problem is, that i can only choose Com 1 to Com 3 in mtty 1.42 - Because of this i can't use the methode which is explained. - What i am making wrong? - I use a Sony Vaio Laptop for booting...
Thanks a lot!
if you have the rom try tis out!
1.unzip the file!
2.put the rom-extended rom-radio(or whatever you need!) in this folder
3.when you'll connect the phone on the usb,on the screen you have to see "usb v1.01".
4.run the "MaUpgradeUt_noID.exe"
5.wait till it will finish flashing!!
6.enjoy the new rom!!
qtek pu10 0r 9000 is freeze please big help
please big help / i just try to change language on my qtek 9000 and when the phone finish. and the screen freeze. and i off it and on it .and still the display show but freezing. and it can't connect to the active sync and pc /please help
Try a soft-reset first.
If not, you may have to hard-reset. You will lose all your data and programs you've installed and it will revert to factory state (or last flashed ROM).