Hi there
I have accidentally close the LG Flash Tool while the program is flashing my phone
And now, the phone stays in black screen and keeps in download mode
When i try to flash the phone using LG Flash Tool again with TOT/ universal DLL
It seems that the phone has lost PID, IMEI, Phone Model, SWversion information, therefore the flash will not run
I have googled for half day but can't find any answer, Pls HELP!!!
(pls forgive my english)
here is error message when using D855 DLL
rgb said:
here is error message when using D855 DLL
Click to expand...
Click to collapse
Your best bet would be to use LG software tool. You will get the rom at the factory setting and you will have to root the phone again (if you so desire). The tools and drivers can be downloaded from the link below. Once you install the tools on a PC, just plug in your phone with USB drive and follow the prompts. Here is the link for the tools:
http://www.mylgphones.com/lg-software-tools-download
Good luck!!
Nope no solution. Motherboard is corrupted. Use your warranty and get the phone RMA'd
Thanks for reply
The phone has been repaired by a professional
There is no any soldering required, and done by shorting two pins on the board, and flash with qhusb USB interface
Quiet simple way to repair
All imei/other info exists
Hello guys,
I'm using my 3T carefully as a media device just at home. But suddenly I couldn't control my system anymore. I could swipe and open settings, but couldn't turn on WiFi or start any app. So I restarted my phone but it never booted. Screen is completely black and even charging leds doesn't work anymore. I can't access TWRP recovery. I used the button combinations ... Nothing! But when I connect my phone to my computer windows plays the typical sound like when you plug in an USB stick. Windows sayed once that the connected device is buggy and cannot be detected. Nothing more. When I reconnect no more message or pop up again.
Has anyone any idea? Thanks a lot!
slev!n said:
Hello guys,
Screen unit is completely dead. It even doesn't show a charging led anymore. I can't access TWRP recovery. I used the button combinations ... Nothing! But when I connect to the computer windows registers my phone by playing the 'connected sound'. But nothing more. Has anyone any idea or know where I can discuss my issue? Thanks a lot!
Click to expand...
Click to collapse
That's weird. Sounds like your screen (if not more parts) died. Hardware issue? Water damage? Might be better to contact a repair center since if you can't even access recovery I doubt the problem is related to LOS. Never happened on my 3T over the 4 years I've had it, though it's had its fair share of damage.
knpk13 said:
That's weird. Sounds like your screen (if not more parts) died. Hardware issue? Water damage? Might be better to contact a repair center since if you can't even access recovery I doubt the problem is related to LOS. Never happened on my 3T over the 4 years I've had it, though it's had its fair share of damage.
Click to expand...
Click to collapse
But before my restart I could use the screen it just looks like something in the system doesn't work: could type on apps and settings, it just doesn't open or pop back. And the charging led is not part of the screen unit as I know.... If I could take out the battery I would do it. It often works in other phones. But I don't have tools here for my 3T. :/
knpk13 said:
That's weird. Sounds like your screen (if not more parts) died. Hardware issue? Water damage? Might be better to contact a repair center since if you can't even access recovery I doubt the problem is related to LOS. Never happened on my 3T over the 4 years I've had it, though it's had its fair share of damage.
Click to expand...
Click to collapse
slev!n said:
But before my restart I could use the screen it just looks like something in the system doesn't work: could type on apps and settings, it just doesn't open or pop back. And the charging led is not part of the screen unit as I know.... If I could take out the battery I would do it. It often works in other phones. But I don't have tools here for my 3T. :/
Click to expand...
Click to collapse
slev!n said:
Hello guys,
I've got an issue and don't know if it belongs to the build or not. I'm on the last build with my 3T and today after charging my phone I couldn't turn on WiFi or start any app. It just didn't open. So I restated my phone but it never booted. Screen unit is completely dead. It even doesn't show a charging led anymore. I can't access TWRP recovery. I used the button combinations ... Nothing! But when I connect to the computer windows registers my phone by playing the 'connected sound'. But nothing more. Has anyone any idea or know where I can discuss my issue? Thanks a lot!
Click to expand...
Click to collapse
Sounds to me like an hardware error involving (but not necessarily limited to) emmc access. That would explain, why the parts still in ram (like homescreen) were still working but apps won't start anymore, as well as the blank screen on device startup (even the logo needs emmc access to read the logo partition).
Try unbricking (I'm afraid your pc won't find the device, if my guess is correct), if that fails: rma or repair center.
slev!n said:
Has anyone any idea or know where I can discuss my issue? Thanks a lot!
Click to expand...
Click to collapse
here
You need to be more spesific about the connected sounds, does it shows up on device manager or else, in detail (with SS/photos etc to prevent misjudge)
150208 said:
here
You need to be more spesific about the connected sounds, does it shows up on device manager or else, in detail (with SS/photos etc to prevent misjudge)
Click to expand...
Click to collapse
Thanks, I'll create a post there. Just one more post here:
I used this phone just carefully at home as a media device. So this brick came totally out of nowhere. When I connect my bricked 3T now to my computer it makes the typical sound like when you plug in an USB stick. Windows sayed once that the connected device is buggy and cannot be detected. Nothing more. When I reconnect no more pop up again.
slev!n said:
I'll create a post there.
Click to expand...
Click to collapse
When you've created that post ask the moderators to move this complete conversation from this thread to the newly created on in the help forum, please. This helps to keep this thread readable and searcheble.
For your trouble: if you can't boot rom, recovery nor fastboot mode, it doesn't make sense to debug the usb connection: what should the pc connect to if none of the three is bootable? There is just nothing up to connect to. That's why I recommended unbrick tool - if that fails rma or go to a repair center.
Hello guys,
I'm using my 3T carefully as a media device just at home. But suddenly I couldn't control my system anymore. I could swipe and open settings, but couldn't turn on WiFi or start any app. So I restarted my phone but it never booted. Screen is completely black and even charging leds doesn't work anymore. I can't access TWRP recovery. I used the button combinations ... Nothing! But when I connect my phone to my computer windows plays the typical sound like when you plug in an USB stick. Windows sayed once that the connected device is buggy and cannot be detected. Nothing more. When I reconnect no more message or pop up again.
Has anyone any idea? Thanks a lot!
Post SS of the device manager after connecting the phone to the PC
150208 said:
Post SS of the device manager after connecting the phone to the PC
Click to expand...
Click to collapse
It doesn't make sense to debug the pc conmection: if neither recovery, fastboot mode nor rom is bootable, there is nothing up and running the pc can connect to (maybe unbrick tool can still access the msm hardware directly, but that's not sure - confirmation is still missing from @slev!n). I'm writing this the second time.
If none of recovery, fastboot mode nor rom is bootable, the last resource before rma or repair center is unbrick tool. I'm writing this the third time!
@slev!n: please ask the moderators to move the existing conversation to thos from the los16 thread here. If all postings have moved, ask the moderators to move this thread from op3/help to op3t/help.
@nvertigo67 I wanted to do so and was searching how to contact moderators but couldn't find it in my XDA app. Maybe someone can give me a hint? I'm kind of new on xda... Thanks!
@150208 And as I wrote: it's not possible to get any kind of message on windows anymore. Just the sound appears when I connect and disconnect.
@nvertigo67 I was also following your advice to use the unbrick tool. I followed the steps on oneplus forum:
https://forums.oneplus.com/threads/guide-oneplus-3-3t-unbrick.531047/
When it comes to the integrity check windows doesn't accept "TESTSIGNING ON". And so windows doesn't recognise my phone in the device manager for the next steps.
And I guess RMA or repair centres are super expensive. I don't know if it's worth it? I thought about buying a device with a broken screen on eBay and try to change the motherboard...
Log in with a web browser locate each posting of the comversation. For each posting in question use the little triangle icon at the botom on the left side, report each posting, set non-urgent and pit the link of this thread together with something like "Please move this posting to the linked thread, thanx in advance".
For disabling driver signature enforcement try method 2. from this post: http://maxedtech.com/about-testmode/
Most of tbe time xda postings are more reliable and more current then the Oneplus forums: https://forum.xda-developers.com/oneplus-3/how-to/op3-collection-unbrick-tools-t3896722, https://forum.xda-developers.com/oneplus-3/how-to/op3-collection-unbrick-tools-t3896722
slev!n said:
[MENTION=4405529]i thought about buying a device with a broken screen on eBay and try to change the motherboard...
Click to expand...
Click to collapse
If you already have a thought why do you keep asked here though? If you want another possible solution, at least put an effort to provide the information needed when asked by the one who tried to help you
I'm not into a guessing games, so i'm out
nvertigo67 said:
It doesn't make sense to debug the pc conmection: if neither recovery, fastboot mode nor rom is bootable, there is nothing up and running the pc can connect to (maybe unbrick tool can still access the msm hardware directly, but that's not sure - confirmation is still missing from @slev!n). I'm writing this the second time.
If none of recovery, fastboot mode nor rom is bootable, the last resource before rma or repair center is unbrick tool. I'm writing this the third time!
Click to expand...
Click to collapse
There are 2 possible reason when the phone is not detected by the computer, driver or hw problem.
To know it i need to look at the device manager status
If it's hw problem, i'll try not to jump on MB conclussion yet, since there are still another possible reason
When talking about MSM, you need to make sure it's available first on the device manager
Otherwise, it's a waste of data for downloading the tool in these human malware days
Oh yes, the msm guide is quite lag behind. You don't need to boot into test mode anymore with the current driver for qualcomm
I flashed a lot qualcomm devices with w10 without the need to boot into test mode
150208 said:
There are 2 possible reason when the phone is not detected by the computer, driver or hw problem.
To know it i need to look at the device manager status
Click to expand...
Click to collapse
True, if only "win is not detecting the device" is known. Since we know much more (neither rom, recovery nor fastboot mode are bootable), the debugging of the usb driver doesn't make sense. The msm tool uses it's own drivers to detect the hardware BEFORE one of the three is booted. If the msm tool has unbricked the device and booting recovery, rom and/or fastboot, you can start debugging the "nprmal" qc usb drivers, if still necessary.
For the costs of rma: maybe it's expensive - maybe oneplus will be obliging... Since you don't relay on the device as your daily driver, you can ask for an estimate of costs - so you can decide if it's worth the costs.
nvertigo67 said:
True, if only "win is not detecting the device" is known. Since we know much more (neither rom, recovery nor fastboot mode are bootable), the debugging of the usb driver doesn't make sense. The msm tool uses it's own drivers to detect the hardware BEFORE one of the three is booted. If the msm tool has unbricked the device and booting recovery, rom and/or fastboot, you can start debugging the "nprmal" qc usb drivers, if still necessary.
Click to expand...
Click to collapse
Wait, I fail to see your explanation in line with mine. I want to start debug it on the windows side, but you seems to see it on the phone side.
Do you realize there are cases where everything is black/nothing responding but it's still detected by computer? That when emmc is corrupt, but repairable if you format it.
150208 said:
Do you realize there are cases where everything is black/nothing responding but it's still detected by computer? That when emmc is corrupt, but repairable if you format it.
Click to expand...
Click to collapse
If neither fastboot mode nor recovery is bootable, you need the msm interface to refprmat somethimg on emmc. In other words: if there's no recovery nor fastboot, you can't utilize adb or fastboot to reformat or to fix the partition table. You need something to connect to to do the fixing, but without recovery or fastboot, there is nothing adb or fastboot can conmect to, no matter of the driver status on the pc/win side. Once this is fixed (at least fastboot mode is up again) you can utilize the "normal" usb connection again.
What do you want to do with the usb connection, if neither fastboot mode nor recovery is up amd running? What is your suggested next step, if the device is recognized? What should the pc recognize if neither fastboot nor adb os an option? Which command or procedure will fix the emmc?
nvertigo67 said:
If neither fastboot mode nor recovery is bootable, you need the msm interface to refprmat somethimg on emmc.
Click to expand...
Click to collapse
Yes, there are other tools but i'm not gonna bother since it's paid
nvertigo67 said:
In other words: if there's no recovery nor fastboot, you can't utilize adb or fastboot to reformat or to fix the partition table. You need something to connect to to do the fixing, but without recovery or fastboot, there is nothing adb or fastboot can conmect to, no matter of the driver status on the pc/win side.
Click to expand...
Click to collapse
This is the part where you're incorrect. There are 4 status when a device plugged into the pc.
1. detected and driver is loaded
2. detected and driver isn't loaded
3. detected but not recognized
4. no sign at all
1 and 2 is sw problem, 3 and 4 is hw problem
In order for MSM to do it's job, you need to have either problem no 1 or 2 with qualcomm qloader 9008 driver already or later detected in devmanager
So it's important to know the driver status
OP states there was sounds coming then nothing, which mean it's either 2 or 3, more like 3 but again i repeating myself i don't like guessing games
I don't understand the part why you're explaining/asking about fastboot recovery or etc, his phone is on dead state, nothing-literally-no sign of life unless he plug it to the pc and then it making sounds for the first time,
Why do you even bother thinking about it?
nvertigo67 said:
Which command or procedure will fix the emmc?
Click to expand...
Click to collapse
No procedure will fixed his phone since there are no enough information
I think your other question should be already answered. If else, i don't know what to say anymore.
150208 said:
nvertigo67 said:
In other words: if there's no recovery nor fastboot, you can't utilize adb or fastboot to reformat or to fix the partition table. You need something to connect to to do the fixing, but without recovery or fastboot, there is nothing adb or fastboot can conmect to, no matter of the driver status on the pc/win side.
Click to expand...
Click to collapse
This is the part where you're incorrect.
Click to expand...
Click to collapse
If so, please explain how you can format a partition or fix the partition table if neither fastboot mode nor recovery (or a rooted system for that matter) is bootable.
@slev!n: please give a screenshot of the device manager to @150208. I'm too curious to learn how to fix a broken emmc without recovery nor fastboot mode.
Thank you so far!
I dont want to bother someone. Just thinking about further options thats why I wrote my thought about replacing the motherboard down.
I 'm in test mode now and I did this:
"Step 4 :- Press the power button for 40 seconds to turn off the phone.
Step 5 :- Press only volume up button for a few seconds and while keeping it pressed,connect your phone to PC.Keep volume up pressed till your device shows in device manager as [Unknown Device,QHUSB_BULK (under Unknown Devices) or Qualcomm HS USB (under COMs and Ports)]."
But no device is listet in my device manager. But in msmtool my phone is connected. Does it mean I cann't continue with this tool somehow?
slev!n said:
But no device is listet in my device manager. But in msmtool my phone is connected. Does it mean I cann't continue with this tool somehow?
Click to expand...
Click to collapse
The pic is from msm tool, not the device manager. No unknown device in device manager?
Sorry for a new thread. My device went into brick state . Cannot even use power and volume button. Followed almost majority of youtube and xda. The process of Ant flash or flash was not working older versions also. It gets stuck with authorisation as I am using EDL mode . Is there a way to skip Auth. Kindly help.
No you can't skip auth, you have to get it on your Xiaomi account which will take 30-60 days or in some cases more. Or they can just ignore/deny it.
You can use test-point method, but do it on your own risk. If you mess something in your motherboard then you can kiss your phone goodbye.
Alternatively you can just send your device to a service center and they will fix it for you.
However if your phone is detected in fastboot mode. Then you can fix it yourself.
Try downloading this driver then check if your device is detected in fastboot.
XDHx86 said:
No you can't skip auth, you have to get it on your Xiaomi account which will take 30-60 days or in some cases more. Or they can just ignore/deny it.
You can use test-point method, but do it on your own risk. If you mess something in your motherboard then you can kiss your phone goodbye.
Alternatively you can just send your device to a service center and they will fix it for you.
However if your phone is detected in fastboot mode. Then you can fix it yourself.
Try downloading this driver then check if your device is detected in fastboot.
Click to expand...
Click to collapse
Thank you . ADB ( have a warning kind of symbol) when I connect phone I get a refresh kind of stuff happening in Device manager but ADB continue to have that code (10)). How to resolve this or if this normal then I am unable to access the phone .
Secondly Test-Point Method (I am yet to get to it) is this EDL mode then I did try couple of time as there are many threads but I think everyone showed Video but continued to state no Auth is required so I tried more times now but no luck .. I will google more on Test Point method if that is different. Appreciate your answer
Who should we approach to get an Authorization (Will give a try ) as service center states mother board replacement. All threads related this were in 2018.. Just saw one thread but that was kind of not leading to closure .
Teddy126 said:
Thank you . ADB ( have a warning kind of symbol) when I connect phone I get a refresh kind of stuff happening in Device manager but ADB continue to have that code (10)). How to resolve this or if this normal then I am unable to access the phone .
Secondly Test-Point Method (I am yet to get to it) is this EDL mode then I did try couple of time as there are many threads but I think everyone showed Video but continued to state no Auth is required so I tried more times now but no luck .. I will google more on Test Point method if that is different. Appreciate your answer
Who should we approach to get an Authorization (Will give a try ) as service center states mother board replacement. All threads related this were in 2018.. Just saw one thread but that was kind of not leading to closure .
Click to expand...
Click to collapse
Your reply is all over the place, I didn't get a single thing of what you said.
Just boot your device to fastboot then type in cmd fastboot devices if you get a response with your device id then your device is detected in fastboot.
Test-point is exactly EDL mode just that you access it directly from the chipset instead of the normal way so it skips auth.
You have to connect two points in the motherboard with your usb then connect it to the PC with the correct driver (Qualcomm 9008)
If you don't know what you're doing then get it to a professional or some friend of yours, don't break it more.
XDHx86 said:
Your reply is all over the place, I didn't get a single thing of what you said.
Just boot your device to fastboot then type in cmd fastboot devices if you get a response with your device id then your device is detected in fastboot.
Test-point is exactly EDL mode just that you access it directly from the chipset instead of the normal way so it skips auth.
You have to connect two points in the motherboard with your usb then connect it to the PC with the correct driver (Qualcomm 9008)
If you don't know what you're doing then get it to a professional or some friend of yours, don't break it more.
Click to expand...
Click to collapse
Thank and sorry for the confusion.
Please note cannot get to Fastboot mode as power+Vol Down does not respond. What i tried to explain is when I installed ADB drives I get a warning symbol in device management
Tried EDL mode with tweezers by simultaneous connecting so that I try flashing. There were some video's. But I could not flash as it was asking Auth.
Teddy126 said:
Thank and sorry for the confusion.
Please note cannot get to Fastboot mode as power+Vol Down does not respond. What i tried to explain is when I installed ADB drives I get a warning symbol in device management
Tried EDL mode with tweezers by simultaneous connecting so that I try flashing. There were some video's. But I could not flash as it was asking Auth.
Click to expand...
Click to collapse
Well then you have no options but to it give to a professional since you can't do a test-point boot.
XDHx86 said:
Well then you have no options but to it give to a professional since you can't do a test-point boot.
Click to expand...
Click to collapse
Thank you will follow this advise. Just tried by seeing EDL videos which I realize is not true and everyone might have had auth code. Thank you for resp[onding