[Q] G3 totally bricked - even no PID, IMEI, Phone Model, SWversion - G3 Q&A, Help & Troubleshooting

Hi there
I have accidentally close the LG Flash Tool while the program is flashing my phone
And now, the phone stays in black screen and keeps in download mode
When i try to flash the phone using LG Flash Tool again with TOT/ universal DLL
It seems that the phone has lost PID, IMEI, Phone Model, SWversion information, therefore the flash will not run
I have googled for half day but can't find any answer, Pls HELP!!!
(pls forgive my english)

here is error message when using D855 DLL

rgb said:
here is error message when using D855 DLL
Click to expand...
Click to collapse
Your best bet would be to use LG software tool. You will get the rom at the factory setting and you will have to root the phone again (if you so desire). The tools and drivers can be downloaded from the link below. Once you install the tools on a PC, just plug in your phone with USB drive and follow the prompts. Here is the link for the tools:
http://www.mylgphones.com/lg-software-tools-download
Good luck!!

Nope no solution. Motherboard is corrupted. Use your warranty and get the phone RMA'd

Thanks for reply
The phone has been repaired by a professional
There is no any soldering required, and done by shorting two pins on the board, and flash with qhusb USB interface
Quiet simple way to repair
All imei/other info exists

Related

D851 Hard Brick

I cannot boot into download mode and cannot boot into twrp. The phone will not boot no matter how long i hold the power button and there is no lights. When connected to the pc it shows up as Qcom Dload. Can someone please create a debrick.img. All you need to do is flash this in twrp and send me the debrick file which should end up on your sdcard.
h ttps://www.androidfilehost.com/?fid=23578570567721355
Nit3H8wk said:
I cannot boot into download mode and cannot boot into twrp. The phone will not boot no matter how long i hold the power button and there is no lights. When connected to the pc it shows up as Qcom Dload. Can someone please create a debrick.img. All you need to do is flash this in twrp and send me the debrick file which should end up on your sdcard.
h ttps://www.androidfilehost.com/?fid=23578570567721355
Click to expand...
Click to collapse
This has been tried before and it didnt work for the guy. Have you tried flashing a tot? It has the begining of the emmc so same outcome but you can skip all the sd card work. Good luck if the tot fails and no one steps up ill get you that debrick file just to see if your luck is better.
ThePagel said:
This has been tried before and it didnt work for the guy. Have you tried flashing a tot? It has the begining of the emmc so same outcome but you can skip all the sd card work. Good luck if the tot fails and no one steps up ill get you that debrick file just to see if your luck is better.
Click to expand...
Click to collapse
That was a no go i tried the older dll that bypass model checks but still fails. Guess there is a linux method that worked on the older g2 and someone with a g3 reported success so i already extracted the TOT files i need to dd over from linux.
h ttp://forum.xda-developers.com/showthread.php?t=2582142
Nit3H8wk said:
That was a no go i tried the older dll that bypass model checks but still fails. Guess there is a linux method that worked on the older g2 and someone with a g3 reported success so i already extracted the TOT files i need to dd over from linux.
h ttp://forum.xda-developers.com/showthread.php?t=2582142
Click to expand...
Click to collapse
Yeah that's probably your best option I have a partitions dump from the tot if yours are not working for some reason. Instead of installing twrp If I was you I would boot into download mode after and flash the tot. I did do a debrick dump with the script that I can get to you tomorrow some time and if that doesn't work tell me and I can give you a link that has 250-500mb range for the dumps from when I was helping the other guy. They weren't made with a script but with terminal emulator but they should be the same thing just bigger because the smaller dumps weren't working for him. Any way here are the partitions just in case https://www.androidfilehost.com/?fid=23622183712472493
---------- Post added at 11:59 PM ---------- Previous post was at 11:36 PM ----------
Oh and before I go to bed another thing you can try if you can send the images over but they don't seem to work. Hunt down the fastboot laf.img send that over then do the rest of the partitions via fastboot instead. Good luck!
Dead phone
Dead in the water. Only qpst seems to see it besides device manager (Qualcomm HS-USB QDLoader 9008). The linux method was for people who get the lg logo. I don't get anything but a black screen. Problem is i don't know enough about the qpst software to guide you on making the files. All i can say is try to make a backup using qpst and provide links. Don't know what else to do.
Nit3H8wk said:
Dead in the water. Only qpst seems to see it besides device manager (Qualcomm HS-USB QDLoader 9008). The linux method was for people who get the lg logo. I don't get anything but a black screen. Problem is i don't know enough about the qpst software to guide you on making the files. All i can say is try to make a backup using qpst and provide links. Don't know what else to do.
Click to expand...
Click to collapse
In order to get you the files someone needs to reboot from the hidden menu into somthing I cant remember. Its not mini os and the d851 lacks the option in hidden menu atleast I didnt see it. The d855 hidden menu has the option and I was going to try it but he ended up sending it in before I got around to flashing the d855 rom. If you want to fix it yourself and can do without a cell phone for a few days I can try but might not be able to get you the files until sunday if it works.
ThePagel said:
In order to get you the files someone needs to reboot from the hidden menu into somthing I cant remember. Its not mini os and the d851 lacks the option in hidden menu atleast I didnt see it. The d855 hidden menu has the option and I was going to try it but he ended up sending it in before I got around to flashing the d855 rom. If you want to fix it yourself and can do without a cell phone for a few days I can try but might not be able to get you the files until sunday if it works.
Click to expand...
Click to collapse
Yeah i will have to wait then can't afford the $175 deductible right now. Thanks for the help. I don't mind waiting just hope i can find a less costly solution know what i mean?
QPST
So it looks like i will need a hex file and mbn partition files vs the bin files that come from the tot file. From what i read in the forums lg offers a 1 year warrenty. So i guess as a last resort i could send it in for service but i would rather try to resolve it myself.
Nit3H8wk said:
So it looks like i will need a hex file and mbn partition files vs the bin files that come from the tot file. From what i read in the forums lg offers a 1 year warrenty. So i guess as a last resort i could send it in for service but i would rather try to resolve it myself.
Click to expand...
Click to collapse
Yeah I got ready to do it last night but got side tracked hopefully tonight
qpst
ThePagel said:
Yeah I got ready to do it last night but got side tracked hopefully tonight
Click to expand...
Click to collapse
I get paid on monday so going to ship it out to LG then. But if you are able to get the hex and mbn and secure boot files let me know i would still like to tinker a bit before that time as i know it will take a few weeks to get the phone back otherwise.
Nit3H8wk said:
I get paid on monday so going to ship it out to LG then. But if you are able to get the hex and mbn and secure boot files let me know i would still like to tinker a bit before that time as i know it will take a few weeks to get the phone back otherwise.
Click to expand...
Click to collapse
Ill be able to tell you tomorrow afternoon if I can do it.
Nit3H8wk said:
I get paid on monday so going to ship it out to LG then. But if you are able to get the hex and mbn and secure boot files let me know i would still like to tinker a bit before that time as i know it will take a few weeks to get the phone back otherwise.
Click to expand...
Click to collapse
I cant seem to get into diag mode or field test mode so I cannot create the files for you :crying: BUT before you completely give up on fixing it take a look at this http://forum.cyanogenmod.org/topic/71825-hard-brick-to-hell-and-back-guide-to-recovery/
Qualcomm MSM8975AC
Hello
I tell them my story, mistakenly doing a ported rom stock LG G3 Marshmallow, I flashed my phone with the stock rom from Marshmallow (model D855) and after that I have bricked the phone. No download mode, no emergency mode, only is recognize for the computer as AndroiNet usb port serial.
Could please you help me to unbrick my lg g3 Phone model d851,t-mobile variant. When I plug in my Phone to computer, this is recognized as lgandroinet port serial but I have made a testpoint (open the mobile) to change the phone mode to Qualcomm HS-USB QDLoader 9008”. I have used tools like boardiag but I get the followin message: “No response from the device. Check PMIC first and if still boot problem, replace AP.” To look at this thread: http://www.androidbrick.com/unbrick-recover-your-dead-lg-g3-g2-all-variants/ ... but report that it is not compatible for ATT and Tmobile variations. I currently have two virtual machines: Window xp 32 bit and Ubuntu 15.04. My client OS is 8.1 Window 64 bit.
I will be very grateful if you can help me to find a solution or can show me which is the correct way. I've been several weeks looking for a solution but I have not been able to fix my cellphone. I hope that my computer still recognizes it.
cesarandres_8911 said:
Qualcomm MSM8975AC
Hello
I tell them my story, mistakenly doing a ported rom stock LG G3 Marshmallow, I flashed my phone with the stock rom from Marshmallow (model D855) and after that I have bricked the phone. No download mode, no emergency mode, only is recognize for the computer as AndroiNet usb port serial.
Could please you help me to unbrick my lg g3 Phone model d851,t-mobile variant. When I plug in my Phone to computer, this is recognized as lgandroinet port serial but I have made a testpoint (open the mobile) to change the phone mode to Qualcomm HS-USB QDLoader 9008”. I have used tools like boardiag but I get the followin message: “No response from the device. Check PMIC first and if still boot problem, replace AP.” To look at this thread: http://www.androidbrick.com/unbrick-recover-your-dead-lg-g3-g2-all-variants/ ... but report that it is not compatible for ATT and Tmobile variations. I currently have two virtual machines: Window xp 32 bit and Ubuntu 15.04. My client OS is 8.1 Window 64 bit.
I will be very grateful if you can help me to find a solution or can show me which is the correct way. I've been several weeks looking for a solution but I have not been able to fix my cellphone. I hope that my computer still recognizes it.
Click to expand...
Click to collapse
I just did the same thing tonight, I'll let you know if I fix it.
mxpxboi said:
I just did the same thing tonight, I'll let you know if I fix it.
Click to expand...
Click to collapse
Hello,
What is your phone and variant model? Do you have D851 model?
Yeah D851, Black Screen and only connects as "LGE androidnet usb serial port"
Tried flashing TOT file and I get the error "Model Information Check FAIL!"
mxpxboi said:
Yeah D851, Black Screen and only connects as "LGE androidnet usb serial port"
Tried flashing TOT file and I get the error "Model Information Check FAIL!"
Click to expand...
Click to collapse
Hello,
I will try help you, first of all you must to change the Qualqomm mode in your phone, namely change usb LGE Androinet by QDloader 9008. For this you must remove the battery from the phone, open the phone and use copper cable or tweezers and you must to touch two points on the mainboard in order to force Qualcomm mode on your phone. I have attached photos to guide you in this process. You must touch two points (without battery) and connect the usb cable to the computer. You'll hear a sound that indicates that qualcomm is active otherwise could see a battery warning on the screen. If this happens, you must disconnect the usb cable and repeat the process.
The second thing you're going to do is install the drivers appropriate for Qualcomm mode. Please follow this thread: http://www.droidsavvy.com/unbrick-qualcomm-mobiles/
This is the download link for the drivers referred to the post: http://forum.xda-developers.com/attachment.php?attachmentid=3261089&stc=1&d=1428980071
Now your computer will recognize the cellular in the indicated mode (Relink HS-USB QDloader 9008).
The next step is to use the Boarddiag tool in this post but in the root folder, place the file sbl1.mbn which is located in the folder that you extract the file TOT.
I am currently uploading a package that includes bordiag tool, sbl1.mbn file, and TOT file extracted. When the upload is complete, I could tell you what is the download link, this contain the version of Boardiag that will work in our model. Currently my phone lg g3 D851 (chip MSM8975AC) was revived.
cesarandres_8911 said:
Hello,
I will try help you, first of all you must to change the Qualqomm mode in your phone, namely change usb LGE Androinet by QDloader 9008. For this you must remove the battery from the phone, open the phone and use copper cable or tweezers and you must to touch two points on the mainboard in order to force Qualcomm mode on your phone. I have attached photos to guide you in this process. You must touch two points (without battery) and connect the usb cable to the computer. You'll hear a sound that indicates that qualcomm is active otherwise could see a battery warning on the screen. If this happens, you must disconnect the usb cable and repeat the process.
The second thing you're going to do is install the drivers appropriate for Qualcomm mode. Please follow this thread: http://www.droidsavvy.com/unbrick-qualcomm-mobiles/
This is the download link for the drivers referred to the post: http://forum.xda-developers.com/attachment.php?attachmentid=3261089&stc=1&d=1428980071
Now your computer will recognize the cellular in the indicated mode (Relink HS-USB QDloader 9008).
The next step is to use the Boarddiag tool in this post but in the root folder, place the file sbl1.mbn which is located in the folder that you extract the file TOT.
I am currently uploading a package that includes bordiag tool, sbl1.mbn file, and TOT file extracted. When the upload is complete, I could tell you what is the download link, this contain the version of Boardiag that will work in our model. Currently my phone lg g3 D851 (chip MSM8975AC) was revived.
Click to expand...
Click to collapse
Good morning, please try downloading this package;
https://mega.nz/#!5lRGUZqZ!HZXaf4SP_PtuPEkg0ycdWXZP977_lBdVVqkI1P8DVtU
I'm not sure if it will work for your model, please performs the tests at your risk. Let me clarify that this is the same boarddiag version , only I try added the files needed.
Within the. 7z, there is a file called "TOT Extract", please extract it and open application BoardDiag. In the section "Target Dir" choose the path where you extracted the file.
Please inform me as it was with the tests.
cesarandres_8911 said:
Good morning, please try downloading this package;
https://mega.nz/#!5lRGUZqZ!HZXaf4SP_PtuPEkg0ycdWXZP977_lBdVVqkI1P8DVtU
I'm not sure if it will work for your model, please performs the tests at your risk. Let me clarify that this is the same boarddiag version , only I try added the files needed.
Within the. 7z, there is a file called "TOT Extract", please extract it and open application BoardDiag. In the section "Target Dir" choose the path where you extracted the file.
Please inform me as it was with the tests.
Click to expand...
Click to collapse
Thank you SOOO much for your help so far.
I installed Qualcomm Drivers and touched the points and it connected.
But it says that the Drivers are blocked due to not being digitally signed.
And it's showing up in Device Manager as "Qualcomm HS-USB QDLoader 9008" with an exclamation point.
I am posting screen shots.'
You didn't have this issue?
What steps do I do in the BoardDiag exactly? Just add the directory with the file and hit start?
@mxpxboi it seems you're using windows 8/above, you have to disable driver signature, here is how to do it https://learn.sparkfun.com/tutorial...abling-signed-driver-enforcement-on-windows-8
Sent from my LG-D801 using Tapatalk

Overwritten aboot.img -> G3 bricked?

Hi guys,
I made a stupid mistake:
I was overwriting aboot.img from terminal to solve "secure boot failed" error. I didn't have backcase installed and battery fell out.
Now, the phone is bricked or at least the screen remains black, no vibrating, no flashing LED.
Is there anything I can do to revive the phone?
Can you enter anything ? Download mode ?
IF nothing you have to force to qualcomm 9008 mode and use boarddiag to fix the phone
Download-mode (Vol-up while plugging in USB) does not work.
Do you think, I can unbrick it by using willcracker's method?
Is there anything I need to keep in mind? Can you give an estimation whether this approach will solve the issue?
Yes, both willcrackers and the link will fix it
If you somehow fail write here
uhm, it seems as if the archive is protected by password? Any adive on how to get hold of it or any alternative solution?
What's also a little strange: the file "androidbrick_G3_fix.7z" is above 100MB while the download of "BoardDiag v2.99a.zip" is around 7MB...
Do I need to dis-assemble the G3 to short the pins stated here?
I did the EXACT SAME THING. I guess we can be idiots together, right?
Unfortunately, boarddiag refuses to flash with some error about the AP and android_g3_fix fails for me (looks like it's working but does nothing).
If you want to try anroidbrick_g3_fix you can email the author for the password.
I'm at a loss as to what to do, I'm already in qualcomm 9008 mode with drivers...
Follow the steps on this post: http://forum.xda-developers.com/lg-g3/help/fix-marshmallow-autorec-hard-brick-t3284608
After i killed my G3 with TWRP (Autorec for LP) on MM i bring my G3 back to life.
Tip: Use a thin massive copper caple, 0,5mm, and put the other end on the top of the sim-slot for ground.
It´s easier.
Haribo68 said:
Follow the steps on this post: http://forum.xda-developers.com/lg-g3/help/fix-marshmallow-autorec-hard-brick-t3284608
After i killed my G3 with TWRP (Autorec for LP) on MM i bring my G3 back to life.
Tip: Use a thin massive copper caple, 0,5mm, and put the other end on the top of the sim-slot for ground.
It´s easier.
Click to expand...
Click to collapse
I don't have TWRP though, will it work?
Didn't seem to. I've had horrid luck with BoardDiag though...
I'm not sure if it makes any difference, but my phone is a Verizon 32GB LG G3 w/MSM8975AC that came preflashed with 35b 5.1.1 (thanks, ,verizon) and has never seemed to respond to any of the downgrade methods. Hence me playing with partitions, flashing aboot to an earleir version, and getting into this mess by failing to flash sb1.
I'm willing to pay to get this fixed, but unsure where to go or who is reputable.
I have managed to shortcircuit the pins and get my G3 to be listed as "Qualcomm HS-USB QDLoader 9008" and a corresponding COM port.
When I start the "androidbrick_G3_fix" as administrator, the tool shows that "USB Status" is "not ready". In the guide it says:
if your driver is installed you will see your port, if not, youll see “Not ready” in little green window.
Click to expand...
Click to collapse
EDIT:
I've used BoardDiag 2.99a to flash different partions according to this source extracted from *.tot file.
Now the phone (obviously) does not boot and shows "Security Error".
Trying to enter download mode seems to work though as it shows "Download Mode" followed by "Firmware Update".
MacWarrior said:
I have managed to shortcircuit the pins and get my G3 to be listed as "Qualcomm HS-USB QDLoader 9008" and a corresponding COM port.
When I start the "androidbrick_G3_fix" as administrator, the tool shows that "USB Status" is "not ready". In the guide it says:
As I've successfully installed the driver (at least the device is listed in device manager) I don't know how to proceed.
Anyone got an idea how to fix this?
Click to expand...
Click to collapse
You need to do the short and connect the cable with the tool open first. Otherwise for some weird reason it doesn't detect the phone.
It appeared to work for me but did nothing. I hope you have better luck.
---------- Post added at 11:55 AM ---------- Previous post was at 11:12 AM ----------
Just saw your edit.
If you can enter download mode, you can now flash a tot using any online guide for such, and in theory unbrick your phone.
As for me, still no luck.
Willing to paypal gift $30.00 to anyone who can help. I've recieved some help invitations but they all insist I install whatsapp, and I can't do that without a phone...
Currently, I am flashing a kitkat kdz (D85510f_00.kdz) to the phone using LG Flash Tool 2014.
It seems to takes ages but is progressing nevertheless. After 30 minutes the tool says 14% whereas the phone says 5% on the screen. I hope the process speeds up a little...
Wish me luck
----
@ R-T-B:
Are you able to get the phone to 9008 mode? Have you tried using the plain BoardDiag 2.99a to extract from *.tot file and flash those afterwards?
MacWarrior said:
Currently, I am flashing a kitkat kdz (D85510f_00.kdz) to the phone using LG Flash Tool 2014.
It seems to takes ages but is progressing nevertheless. After 30 minutes the tool says 14% whereas the phone says 5% on the screen. I hope the process speeds up a little...
Wish me luck
Click to expand...
Click to collapse
I wish you enough luck for both of us!
But seriously, good luck. Sounds like you are in the home stretch.
EDIT: Yes, I am in 9008. Unfortunately BoardDiag seems to refuse to flash it with AP errors. I think it's an issue with the updated chipset Verizon uses on the 32gb model.

Brick lg g3 After update recovery bump help!

Good evening everyone my name mirko. Help me! I have a problem with my smartphone lg g3 32 Gb italian. I upgraded the recovery bumped .... when I rebooted the screen remains black and there are no signs of life. Do not even enter into download mode. the PC recognizes a sound hardware and wrote LGE Android net usb serial Com Port 7. know a way to help me? thank you
mirko0 said:
Good evening everyone my name mirko. Help me! I have a problem with my smartphone lg g3 32 Gb italian. I upgraded the recovery bumped .... when I rebooted the screen remains black and there are no signs of life. Do not even enter into download mode. the PC recognizes a sound hardware and wrote LGE Android net usb serial Com Port 7. know a way to help me? thank you
Click to expand...
Click to collapse
You have to use unbrick method....find in the forum...also what model you have and what the version of android?
My model is d855 and The android installed is lollipop fw d85520h
Inviato dal mio GT-I9505 utilizzando Tapatalk
1. You need to do is to check the latest version for your phone here by entering your phone's IMEI code.
2. Keep in mind the version and country and download the KDZ file you need.
3. Install LG drivers on your PC.
4. Go to this thread and from the section How to flash ROM KDZ Method start from the 3rd step.
This video shows how to get into Download Mode.
Then you have to root your phone again.
good luck
sharp3r said:
1. You need to do is to check the latest version for your phone here by entering your phone's IMEI code.
2. Keep in mind the version and country and download the KDZ file you need.
3. Install LG drivers on your PC.
4. Go to this thread and from the section How to flash ROM KDZ Method start from the 3rd step.
This video shows how to get into Download Mode.
Then you have to root your phone again.
good luck
Click to expand...
Click to collapse
Ok thanks, but unfortunately the problem of my phone and 'who does not enter the mode' download mode "the screen once connected and hold the volume button is all black and does nothing.
[emoji24] [emoji24]
mirko0 said:
Ok thanks, but unfortunately the problem of my phone and 'who does not enter the mode' download mode "the screen once connected and hold the volume button is all black and does nothing.
[emoji24] [emoji24]
Click to expand...
Click to collapse
You have unbrick your phone with board diag search lg g3 board diag you will find all the procedure and file....if any hekp needed we all are here for helping you....
mirko0 said:
Good evening everyone my name mirko. Help me! I have a problem with my smartphone lg g3 32 Gb italian. I upgraded the recovery bumped .... when I rebooted the screen remains black and there are no signs of life. Do not even enter into download mode. the PC recognizes a sound hardware and wrote LGE Android net usb serial Com Port 7. know a way to help me? thank you
Click to expand...
Click to collapse
Hi, mirko0. We have the same problem and we need to do the same procedures to find the solution.
As seen in the following links:
http://forum.xda-developers.com/sprint-lg-g3/general/guide-fix-hard-brick-recovery-guide-t3132359
http://arena4g.com/forum/threads/unbrick-hard-unbrick-d855.7/ (Brazilian portuguese tutorial)
http://open-freax.fr/guide-unbrick-your-lg-g3/
You'll have to open up your phone (seriously) and make a short circuit in the board. Than, your PC will recognize as Qualcomm 9008.
Do not forget:
Install the x32 or x64 drives
If x64, do not forget to disable drive check
If windows 10, do not forget to reboot in advanced mode and disable drivers check
Everytime the phone reboot, you'll need to make the short circuit. I know, a pain in the ass.
You'll need the MBN folder of the Lollipop or Marshmallow. This is our actual problem
I haven't found the MBN folder of 6.0(v30) or 5.0 (v20), just v10. We'll need those files to proceed.
I finally had to send my phone for repair and I have repaired under warranty, soon expected to return repaired

lg g3 bricked shows qdloaderboard diag says ap check failed device not in dwnld mode

i rooted my lg g3 d 855 lollipop and tried to install TWRP
but it was not a success i lost recovery + download mode but it boots perfectly into android system and can use it normally
to install twrp again i tried to flash it again and again but no success
then i flash aboot.img and it all went blank not booting not rrecovery etc
i tried board diag method to unbrick it shows up in my system as qcomm hs usb 9008
but when using board diag it says DEVICE NOT FOUND IN DLOAD MODE
plz help this is my first android phone after months of hardwork
i dont think i have enough money to replace the mobo or buy a new one:crying:
Hello,
it's recoverable, but you need to read and some knowledge...
Refer to this thread. Proceed point by point and use willcracker boarddiag.
halekhonza said:
Hello,
it's recoverable, but you need to read and some knowledge...
Refer to this thread. Proceed point by point and use willcracker boarddiag.
Click to expand...
Click to collapse
brother i used board diag method it is succesfully able to show my device as qcomm hs usb 9008
and im able extract the files with program
but when i click start after some time it says ap check failed ,device not found in dload mode
i desperately need ur help IM NEW TO XDA FORUMS I HOPE ANYONE WOULD BE ABLE TO SOLVE PROBLEM
tnx in advanc
adilismail62 said:
brother i used board diag method it is succesfully able to show my device as qcomm hs usb 9008
and im able extract the files with program
but when i click start after some time it says ap check failed ,device not found in dload mode
i desperately need ur help IM NEW TO XDA FORUMS I HOPE ANYONE WOULD BE ABLE TO SOLVE PROBLEM
tnx in advanc
Click to expand...
Click to collapse
I understand. I'm just asking if you really using right boarddiag (thread that I mentioned - willcracker.rar)
Also be sure that you have a phone connected to right port (check it in device manager)
halekhonza said:
I understand. I'm just asking if you really using right boarddiag (thread that I mentioned - willcracker.rar)
Also be sure that you have a phone connected to right port (check it in device manager)
Click to expand...
Click to collapse
halekhonza said:
I understand. I'm just asking if you really using right boarddiag (thread that I mentioned - willcracker.rar)
Also be sure that you have a phone connected to right port (check it in device manager)
Click to expand...
Click to collapse
yes im using the r8 port it shows in device manager and in board daig also i gave port 14
before my phone was going to get bricked its battery was low
is it affecting the procedure i think my battery is not charging
when i remove battery and connect to pc phone shows battery not inserted sign when i insert the batery it disappear and no sign of charging
i thought this might help:good:
You have to use the original LG usb cable. Dont try with fake china cables because its a lot possible to have troubles with them.

Help me unbrick my LG d722 (G3s)

https://drive.google.com/file/d/1mg8BDBCaoCS_LXE0TBSd5TdKV81YUsCM/view?usp=sharing[/IMG]
Hi guys,
i need some help unbricking my d722.
what went wrong?
I tried to flash twrp with flashify and i ended up in demigodmode.
from there i connected the phone to my computer and like 10 portable drives showed up asking to be formatted. I formatted all except one drive because it was protected from.
After i formatted the drives my phone was dead with only a black screen left.
Since i can't find any .tot firmware files for this model i tried to use the .tot firmware for a g3 in BoardDiag.
but when i want to use the extracted .tot firmware files on my phone it says this:
no response from device, check pmic first and if still boot problem replace ap
i think i have managed to install qualcomm driver and the phone is recognized as a qualcomm when plugged in.
But i did not shortwire the motherboard because i can't find the GND
can anyone please help me fix my phone thank you so much!

Categories

Resources