Help me unbrick my LG d722 (G3s) - G3 Q&A, Help & Troubleshooting

https://drive.google.com/file/d/1mg8BDBCaoCS_LXE0TBSd5TdKV81YUsCM/view?usp=sharing[/IMG]
Hi guys,
i need some help unbricking my d722.
what went wrong?
I tried to flash twrp with flashify and i ended up in demigodmode.
from there i connected the phone to my computer and like 10 portable drives showed up asking to be formatted. I formatted all except one drive because it was protected from.
After i formatted the drives my phone was dead with only a black screen left.
Since i can't find any .tot firmware files for this model i tried to use the .tot firmware for a g3 in BoardDiag.
but when i want to use the extracted .tot firmware files on my phone it says this:
no response from device, check pmic first and if still boot problem replace ap
i think i have managed to install qualcomm driver and the phone is recognized as a qualcomm when plugged in.
But i did not shortwire the motherboard because i can't find the GND
can anyone please help me fix my phone thank you so much!

Related

D851 Hard Brick

I cannot boot into download mode and cannot boot into twrp. The phone will not boot no matter how long i hold the power button and there is no lights. When connected to the pc it shows up as Qcom Dload. Can someone please create a debrick.img. All you need to do is flash this in twrp and send me the debrick file which should end up on your sdcard.
h ttps://www.androidfilehost.com/?fid=23578570567721355
Nit3H8wk said:
I cannot boot into download mode and cannot boot into twrp. The phone will not boot no matter how long i hold the power button and there is no lights. When connected to the pc it shows up as Qcom Dload. Can someone please create a debrick.img. All you need to do is flash this in twrp and send me the debrick file which should end up on your sdcard.
h ttps://www.androidfilehost.com/?fid=23578570567721355
Click to expand...
Click to collapse
This has been tried before and it didnt work for the guy. Have you tried flashing a tot? It has the begining of the emmc so same outcome but you can skip all the sd card work. Good luck if the tot fails and no one steps up ill get you that debrick file just to see if your luck is better.
ThePagel said:
This has been tried before and it didnt work for the guy. Have you tried flashing a tot? It has the begining of the emmc so same outcome but you can skip all the sd card work. Good luck if the tot fails and no one steps up ill get you that debrick file just to see if your luck is better.
Click to expand...
Click to collapse
That was a no go i tried the older dll that bypass model checks but still fails. Guess there is a linux method that worked on the older g2 and someone with a g3 reported success so i already extracted the TOT files i need to dd over from linux.
h ttp://forum.xda-developers.com/showthread.php?t=2582142
Nit3H8wk said:
That was a no go i tried the older dll that bypass model checks but still fails. Guess there is a linux method that worked on the older g2 and someone with a g3 reported success so i already extracted the TOT files i need to dd over from linux.
h ttp://forum.xda-developers.com/showthread.php?t=2582142
Click to expand...
Click to collapse
Yeah that's probably your best option I have a partitions dump from the tot if yours are not working for some reason. Instead of installing twrp If I was you I would boot into download mode after and flash the tot. I did do a debrick dump with the script that I can get to you tomorrow some time and if that doesn't work tell me and I can give you a link that has 250-500mb range for the dumps from when I was helping the other guy. They weren't made with a script but with terminal emulator but they should be the same thing just bigger because the smaller dumps weren't working for him. Any way here are the partitions just in case https://www.androidfilehost.com/?fid=23622183712472493
---------- Post added at 11:59 PM ---------- Previous post was at 11:36 PM ----------
Oh and before I go to bed another thing you can try if you can send the images over but they don't seem to work. Hunt down the fastboot laf.img send that over then do the rest of the partitions via fastboot instead. Good luck!
Dead phone
Dead in the water. Only qpst seems to see it besides device manager (Qualcomm HS-USB QDLoader 9008). The linux method was for people who get the lg logo. I don't get anything but a black screen. Problem is i don't know enough about the qpst software to guide you on making the files. All i can say is try to make a backup using qpst and provide links. Don't know what else to do.
Nit3H8wk said:
Dead in the water. Only qpst seems to see it besides device manager (Qualcomm HS-USB QDLoader 9008). The linux method was for people who get the lg logo. I don't get anything but a black screen. Problem is i don't know enough about the qpst software to guide you on making the files. All i can say is try to make a backup using qpst and provide links. Don't know what else to do.
Click to expand...
Click to collapse
In order to get you the files someone needs to reboot from the hidden menu into somthing I cant remember. Its not mini os and the d851 lacks the option in hidden menu atleast I didnt see it. The d855 hidden menu has the option and I was going to try it but he ended up sending it in before I got around to flashing the d855 rom. If you want to fix it yourself and can do without a cell phone for a few days I can try but might not be able to get you the files until sunday if it works.
ThePagel said:
In order to get you the files someone needs to reboot from the hidden menu into somthing I cant remember. Its not mini os and the d851 lacks the option in hidden menu atleast I didnt see it. The d855 hidden menu has the option and I was going to try it but he ended up sending it in before I got around to flashing the d855 rom. If you want to fix it yourself and can do without a cell phone for a few days I can try but might not be able to get you the files until sunday if it works.
Click to expand...
Click to collapse
Yeah i will have to wait then can't afford the $175 deductible right now. Thanks for the help. I don't mind waiting just hope i can find a less costly solution know what i mean?
QPST
So it looks like i will need a hex file and mbn partition files vs the bin files that come from the tot file. From what i read in the forums lg offers a 1 year warrenty. So i guess as a last resort i could send it in for service but i would rather try to resolve it myself.
Nit3H8wk said:
So it looks like i will need a hex file and mbn partition files vs the bin files that come from the tot file. From what i read in the forums lg offers a 1 year warrenty. So i guess as a last resort i could send it in for service but i would rather try to resolve it myself.
Click to expand...
Click to collapse
Yeah I got ready to do it last night but got side tracked hopefully tonight
qpst
ThePagel said:
Yeah I got ready to do it last night but got side tracked hopefully tonight
Click to expand...
Click to collapse
I get paid on monday so going to ship it out to LG then. But if you are able to get the hex and mbn and secure boot files let me know i would still like to tinker a bit before that time as i know it will take a few weeks to get the phone back otherwise.
Nit3H8wk said:
I get paid on monday so going to ship it out to LG then. But if you are able to get the hex and mbn and secure boot files let me know i would still like to tinker a bit before that time as i know it will take a few weeks to get the phone back otherwise.
Click to expand...
Click to collapse
Ill be able to tell you tomorrow afternoon if I can do it.
Nit3H8wk said:
I get paid on monday so going to ship it out to LG then. But if you are able to get the hex and mbn and secure boot files let me know i would still like to tinker a bit before that time as i know it will take a few weeks to get the phone back otherwise.
Click to expand...
Click to collapse
I cant seem to get into diag mode or field test mode so I cannot create the files for you :crying: BUT before you completely give up on fixing it take a look at this http://forum.cyanogenmod.org/topic/71825-hard-brick-to-hell-and-back-guide-to-recovery/
Qualcomm MSM8975AC
Hello
I tell them my story, mistakenly doing a ported rom stock LG G3 Marshmallow, I flashed my phone with the stock rom from Marshmallow (model D855) and after that I have bricked the phone. No download mode, no emergency mode, only is recognize for the computer as AndroiNet usb port serial.
Could please you help me to unbrick my lg g3 Phone model d851,t-mobile variant. When I plug in my Phone to computer, this is recognized as lgandroinet port serial but I have made a testpoint (open the mobile) to change the phone mode to Qualcomm HS-USB QDLoader 9008”. I have used tools like boardiag but I get the followin message: “No response from the device. Check PMIC first and if still boot problem, replace AP.” To look at this thread: http://www.androidbrick.com/unbrick-recover-your-dead-lg-g3-g2-all-variants/ ... but report that it is not compatible for ATT and Tmobile variations. I currently have two virtual machines: Window xp 32 bit and Ubuntu 15.04. My client OS is 8.1 Window 64 bit.
I will be very grateful if you can help me to find a solution or can show me which is the correct way. I've been several weeks looking for a solution but I have not been able to fix my cellphone. I hope that my computer still recognizes it.
cesarandres_8911 said:
Qualcomm MSM8975AC
Hello
I tell them my story, mistakenly doing a ported rom stock LG G3 Marshmallow, I flashed my phone with the stock rom from Marshmallow (model D855) and after that I have bricked the phone. No download mode, no emergency mode, only is recognize for the computer as AndroiNet usb port serial.
Could please you help me to unbrick my lg g3 Phone model d851,t-mobile variant. When I plug in my Phone to computer, this is recognized as lgandroinet port serial but I have made a testpoint (open the mobile) to change the phone mode to Qualcomm HS-USB QDLoader 9008”. I have used tools like boardiag but I get the followin message: “No response from the device. Check PMIC first and if still boot problem, replace AP.” To look at this thread: http://www.androidbrick.com/unbrick-recover-your-dead-lg-g3-g2-all-variants/ ... but report that it is not compatible for ATT and Tmobile variations. I currently have two virtual machines: Window xp 32 bit and Ubuntu 15.04. My client OS is 8.1 Window 64 bit.
I will be very grateful if you can help me to find a solution or can show me which is the correct way. I've been several weeks looking for a solution but I have not been able to fix my cellphone. I hope that my computer still recognizes it.
Click to expand...
Click to collapse
I just did the same thing tonight, I'll let you know if I fix it.
mxpxboi said:
I just did the same thing tonight, I'll let you know if I fix it.
Click to expand...
Click to collapse
Hello,
What is your phone and variant model? Do you have D851 model?
Yeah D851, Black Screen and only connects as "LGE androidnet usb serial port"
Tried flashing TOT file and I get the error "Model Information Check FAIL!"
mxpxboi said:
Yeah D851, Black Screen and only connects as "LGE androidnet usb serial port"
Tried flashing TOT file and I get the error "Model Information Check FAIL!"
Click to expand...
Click to collapse
Hello,
I will try help you, first of all you must to change the Qualqomm mode in your phone, namely change usb LGE Androinet by QDloader 9008. For this you must remove the battery from the phone, open the phone and use copper cable or tweezers and you must to touch two points on the mainboard in order to force Qualcomm mode on your phone. I have attached photos to guide you in this process. You must touch two points (without battery) and connect the usb cable to the computer. You'll hear a sound that indicates that qualcomm is active otherwise could see a battery warning on the screen. If this happens, you must disconnect the usb cable and repeat the process.
The second thing you're going to do is install the drivers appropriate for Qualcomm mode. Please follow this thread: http://www.droidsavvy.com/unbrick-qualcomm-mobiles/
This is the download link for the drivers referred to the post: http://forum.xda-developers.com/attachment.php?attachmentid=3261089&stc=1&d=1428980071
Now your computer will recognize the cellular in the indicated mode (Relink HS-USB QDloader 9008).
The next step is to use the Boarddiag tool in this post but in the root folder, place the file sbl1.mbn which is located in the folder that you extract the file TOT.
I am currently uploading a package that includes bordiag tool, sbl1.mbn file, and TOT file extracted. When the upload is complete, I could tell you what is the download link, this contain the version of Boardiag that will work in our model. Currently my phone lg g3 D851 (chip MSM8975AC) was revived.
cesarandres_8911 said:
Hello,
I will try help you, first of all you must to change the Qualqomm mode in your phone, namely change usb LGE Androinet by QDloader 9008. For this you must remove the battery from the phone, open the phone and use copper cable or tweezers and you must to touch two points on the mainboard in order to force Qualcomm mode on your phone. I have attached photos to guide you in this process. You must touch two points (without battery) and connect the usb cable to the computer. You'll hear a sound that indicates that qualcomm is active otherwise could see a battery warning on the screen. If this happens, you must disconnect the usb cable and repeat the process.
The second thing you're going to do is install the drivers appropriate for Qualcomm mode. Please follow this thread: http://www.droidsavvy.com/unbrick-qualcomm-mobiles/
This is the download link for the drivers referred to the post: http://forum.xda-developers.com/attachment.php?attachmentid=3261089&stc=1&d=1428980071
Now your computer will recognize the cellular in the indicated mode (Relink HS-USB QDloader 9008).
The next step is to use the Boarddiag tool in this post but in the root folder, place the file sbl1.mbn which is located in the folder that you extract the file TOT.
I am currently uploading a package that includes bordiag tool, sbl1.mbn file, and TOT file extracted. When the upload is complete, I could tell you what is the download link, this contain the version of Boardiag that will work in our model. Currently my phone lg g3 D851 (chip MSM8975AC) was revived.
Click to expand...
Click to collapse
Good morning, please try downloading this package;
https://mega.nz/#!5lRGUZqZ!HZXaf4SP_PtuPEkg0ycdWXZP977_lBdVVqkI1P8DVtU
I'm not sure if it will work for your model, please performs the tests at your risk. Let me clarify that this is the same boarddiag version , only I try added the files needed.
Within the. 7z, there is a file called "TOT Extract", please extract it and open application BoardDiag. In the section "Target Dir" choose the path where you extracted the file.
Please inform me as it was with the tests.
cesarandres_8911 said:
Good morning, please try downloading this package;
https://mega.nz/#!5lRGUZqZ!HZXaf4SP_PtuPEkg0ycdWXZP977_lBdVVqkI1P8DVtU
I'm not sure if it will work for your model, please performs the tests at your risk. Let me clarify that this is the same boarddiag version , only I try added the files needed.
Within the. 7z, there is a file called "TOT Extract", please extract it and open application BoardDiag. In the section "Target Dir" choose the path where you extracted the file.
Please inform me as it was with the tests.
Click to expand...
Click to collapse
Thank you SOOO much for your help so far.
I installed Qualcomm Drivers and touched the points and it connected.
But it says that the Drivers are blocked due to not being digitally signed.
And it's showing up in Device Manager as "Qualcomm HS-USB QDLoader 9008" with an exclamation point.
I am posting screen shots.'
You didn't have this issue?
What steps do I do in the BoardDiag exactly? Just add the directory with the file and hit start?
@mxpxboi it seems you're using windows 8/above, you have to disable driver signature, here is how to do it https://learn.sparkfun.com/tutorial...abling-signed-driver-enforcement-on-windows-8
Sent from my LG-D801 using Tapatalk

[Q] G3 totally bricked - even no PID, IMEI, Phone Model, SWversion

Hi there
I have accidentally close the LG Flash Tool while the program is flashing my phone
And now, the phone stays in black screen and keeps in download mode
When i try to flash the phone using LG Flash Tool again with TOT/ universal DLL
It seems that the phone has lost PID, IMEI, Phone Model, SWversion information, therefore the flash will not run
I have googled for half day but can't find any answer, Pls HELP!!!
(pls forgive my english)
here is error message when using D855 DLL
rgb said:
here is error message when using D855 DLL
Click to expand...
Click to collapse
Your best bet would be to use LG software tool. You will get the rom at the factory setting and you will have to root the phone again (if you so desire). The tools and drivers can be downloaded from the link below. Once you install the tools on a PC, just plug in your phone with USB drive and follow the prompts. Here is the link for the tools:
http://www.mylgphones.com/lg-software-tools-download
Good luck!!
Nope no solution. Motherboard is corrupted. Use your warranty and get the phone RMA'd
Thanks for reply
The phone has been repaired by a professional
There is no any soldering required, and done by shorting two pins on the board, and flash with qhusb USB interface
Quiet simple way to repair
All imei/other info exists

Device will not turn on LG G3 D855 32GB

Hello everyone.
I need your help.
My Device: LG G3 D855 32GB
The device does not turn on, the only thing that appears is because when I connect the device to a PC, I see a driver installed:
RELINK HS-USB QDLoader 9008
I read guides on site here, and I'm trying to order
I downloaded the software BoardDiag 2.9
I downloaded the files to the appropriate TOT
I extracted the files by instructors on site.
I opened the program and I followed the guide and it seems to me an error
Download mode is enabled Mode,
I quickly disconnects from the computer and reconnect the computer and then the moment I am unable to do a test and the results are:
AP CHECK START = PASS
EMMC TEST START
FAILED TO OPEN PARTITION FROM EMMC
TEST ABORTED !!
I tried a lot of tutorials but I can not, it always seems the device is in Download Mode
What can I do more?
Please your help,
Eliran
If you go that way, you will need bunch of other stuff. Here is the link
http://open-freax.fr/guide-unbrick-your-lg-g3/
It is a good thing that your PC recognises phone like that.
But first be sure that You can not enter download mode or recovery or even fastboot.
And please say what did you do to make it like that? Wrong flash?
If you CAN enter download mode than you can flash kdz or tot files from there. Easiest way is to use LGUP but you must be careful if you want to try.
The phone fell
Navuhodonosor said:
If you go that way, you will need bunch of other stuff. Here is the link
It is a good thing that your PC recognises phone like that.
But first be sure that You can not enter download mode or recovery or even fastboot.
And please say what did you do to make it like that? Wrong flash?
If you CAN enter download mode than you can flash kdz or tot files from there. Easiest way is to use LGUP but you must be careful if you want to try.
Click to expand...
Click to collapse
Thanks for the comment
The phone fell into the vehicle.
I know the phone is always in Download Mode
The software does not let me do anything and making phone download mode
I did not try to install KDZ.
And I can not open a setup KDZ because the device does not rise and there is no open port.
I only have the port I did above.
Thanks for the help, I worked in the guide and I could not ...
Navuhodonosor said:
If you go that way, you will need bunch of other stuff. Here is the link
It is a good thing that your PC recognises phone like that.
But first be sure that You can not enter download mode or recovery or even fastboot.
And please say what did you do to make it like that? Wrong flash?
If you CAN enter download mode than you can flash kdz or tot files from there. Easiest way is to use LGUP but you must be careful if you want to try.
Click to expand...
Click to collapse
Thanks for the help, I worked in the guide and I could not ...
I went through all the steps I found at:
Now, let’s get the party started
I set up the software the guide and I got an error:
FAIL on the EMMC test
I changed the parameter Read / Write »to« Erase
And again I got the error:
FAIL on the EMMC test
Then I try again, click Start, open a window and write in English and Chinese
Device DLOAD mode
device was not found in dload trying flash peogrammer
I click OK, the window closes and then when I press Start again, the window reappears.
Only when I disconnect the USB cable from the computer and the author briefly again then I’m able to do the test, but he failed.
FAIL on the EMMC test
The device always is in Download Mode and appears port:
RELINK HS-USB QDLoader 9008
My component can not be right at all and it always is in Download Mode?
I did not do short the guide, because the computer also detected me.
It has always seemed stuck in a download mode.
There is another option? Short elsewhere as will enable progress?
Thank you very much for your help,
Eliran
I need help please. What can i do
zarfati66 said:
Thanks for the help, I worked in the guide and I could not ...
I went through all the steps I found at:
Now, let’s get the party started
I set up the software the guide and I got an error:
FAIL on the EMMC test
I changed the parameter Read / Write »to« Erase
And again I got the error:
FAIL on the EMMC test
Then I try again, click Start, open a window and write in English and Chinese
Device DLOAD mode
device was not found in dload trying flash peogrammer
I click OK, the window closes and then when I press Start again, the window reappears.
Only when I disconnect the USB cable from the computer and the author briefly again then I’m able to do the test, but he failed.
FAIL on the EMMC test
The device always is in Download Mode and appears port:
RELINK HS-USB QDLoader 9008
My component can not be right at all and it always is in Download Mode?
I did not do short the guide, because the computer also detected me.
It has always seemed stuck in a download mode.
There is another option? Short elsewhere as will enable progress?
Thank you very much for your help,
Eliran
Click to expand...
Click to collapse
I need help please. What can i do
The phone woke for a moment ...
zarfati66 said:
I need help please. What can i do
Click to expand...
Click to collapse
Hello everyone
Today I tried again to connect the device to your computer, the screen comes on suddenly.
And see the state of battery with a question mark inside a yellow triangle.
I did not realize also saw installed driver
LGE AndroidNet USB Serial Port
I tried to re-install.
Now again became a black screen and the next thing happens:
When the device without a battery connected to a computer costing me
RELINK HS-USB QDLoader 9008
When I'm with a battery, it registers an unknown device.
When the device without a battery test again tried to do this EMMC component fails.
help please
Eliran
relink hs-USB Qdloader 9008
ZARFATI6 said:
Hello everyone
Today I tried again to connect the device to your computer, the screen comes on suddenly.
And see the state of battery with a question mark inside a yellow triangle.
I did not realize also saw installed driver
LGE AndroidNet USB Serial Port
I tried to re-install.
Now again became a black screen and the next thing happens:
When the device without a battery connected to a computer costing me
RELINK HS-USB QDLoader 9008
When I'm with a battery, it registers an unknown device.
When the device without a battery test again tried to do this EMMC component fails.
help please
Eliran
Click to expand...
Click to collapse
I am exactly in the same situation. Have you found any solution so far???? My phone suddenly stopped working and didn't boot up at all first and then I used the LG Flashtool to install original TOT file and all went well. I forgot to close LG Flashtool and it started flashing again. LG Flash tool restarts the phone at about 80% and then it failed at that point and since then I am having this issue.................
Any solution???????
apur32 said:
I am exactly in the same situation. Have you found any solution so far???? My phone suddenly stopped working and didn't boot up at all first and then I used the LG Flashtool to install original TOT file and all went well. I forgot to close LG Flashtool and it started flashing again. LG Flash tool restarts the phone at about 80% and then it failed at that point and since then I am having this issue.................
Any solution???????
Click to expand...
Click to collapse
Same situation too, solutions yet?
Hey I have the same problem .
If any of you found the solution please post it here or pm me, I am stuck

[HARDBRICK] D855; Boarddiag & flashtool not working

I'm fixing a D855 model which I hardbricked by accident. This is what I tried so far but still unsuccessful:
1. I used the method which involved shorting the pins in order for my PC to detect it as Qualcomm USB QDloader (something). I used the BOARDDIAG v2.99c as it's the only version that could detect my phone connected. Newer versions doesn't seem to work. I flashed all the partitions, even the userdata and system (which the tutorial doesn't recommend as it takes very long; it took me more than 12 hrs+). After flashing the sli, which is supposed to be flashed last, my phone boots to kernel panic mode. From this point, my phone can be seen as LGE androidnet port (COM41) (sorry I'm just typing this from memory)
2. From the kernel panic mode, I used the LG flash tool to flash a D855 TOT and a LG8974.dll. However, it still cannot detect my phone model. IMEI and PID still comes out as null. Back to #1, the reason I also flashed userdata and system partition because flash tool still cannot detect my phone. I was hoping to boot it up using the 1st method but it keeps on throwing it to kernel panic mode.
Any suggestions how to revive my LG G3?
hey, i have the same issue, did you find any sulotion?

LG H735T hard bricked during root + stuck in COM 9008 flash mode

Hi there. Sorry for that weird LG device model. I really want to unbrick it as I need a secondary device.
This device have not been use for a long time now, and the EMMC chip inside of it probably degraded and the kernel and boot data is all gone too. The only thing accessable is Qualcomm 9008 flash mode and a mode that cannot be identified by Windows.
I tried to search online to find 9008 Firmwares for this device and got none as this is a uncommon device and most of it is for H810 or H815.
I also want to request for a developer who can make firmwares please make me one. I don't want to use SD card to unbrick since I don't have the SD card larger then 32GB that is Class 10.
I tried to make my own firmware and it didn't work as I missed a file and I don't know what it is.
If you have successfully made a firmware, thank you first of all. Then you can PM me or just spam it on those firmware sharing site and then send a link to me.
Thank you, I hope you understand.
Also, the device cannot boot into any other mode.
I have fixed it. Apparently, a CyanogenOS device's firehose worked fine for this device. So there we go.

Categories

Resources