Related
:?
I tried to make an update with the file JASJAR_WWE_11353_137_10301
Suddenly the Display stop et 99% of the extended Rom Update and on my monitor was an infomation like "an error happend"
After this, nothing else happend .
Yes, realy nothing happens anymore. I cant start the device not with power, not with reset or with power+reset
nothing nothing nothing
What can i do
If i start to try a new update, it schows me no information about what rom etc. is installed or what will be installed. if i then start i get the notice, that it is the wrong device.
Help me please. ist there any way to put the mda back to live?????
I guess i dont only need an update but the complete software
HELP!!!
I have the exact same issue after the upgrade. Nothing will happen. I spent several hours trying resets, combination of button pressed, removed battery, resets, just to try to get back the boot loader mode but nothing is happening.
there has to be a way to do this and I hope someone on this board had that issue before and got it resolved.
I had a similair issue with my old XDA II, it turned out my storage card was corrupted. Use a card reader to check your storage card is OK, perhaps format the storage card (having saved any data first of course) and see how you fare
Have had the same problem wirh a radio ROM update on my QTEK9000. The anly thin that still worked was the hard reset. After the hard reset the device still did not respond. But when i connected it to the PC I could start the updateprocess of the original ROM. I took about 20 minutes for the whole procedure and than the Qtek9000 was back in factory default (Pffff and I could breath again).
So perhaps you can try a hard rest and then connect aganin to the PC.
I allready tried this!
But nothing happens.
Even if i put the power device or the usb into the mda, no LED schows anything. just sometimes the LED is red for not more than a minute. if it then goes out, i get the message "Unknown usb device" in my PC
Are you in bootloeader mode? Do you see the words USB or Serial on the screen of the Universal in Portrait mode. Note: Backlight is off so you have too look real hard, but it should be there
no, i see nothing.
I had quite a hard time yesterday while upgrading. The bootloader is very hard to see, use a torch to lite up your display. In portrait view on the top should be the word serial or usb, on the bottom v1.00.
I also did a hard-reset in this stage, but it just returned to the bootloader menue.
If I connect to the PC and the device is recognized I see the word serial in the display change to USB. For me I do not know the reason but my PC did not want to fulfill the upgrade process. Needed to take another PC (Laptop) to solve the problem. After the upgrade of the ROM, You still need to upgrade the Radio (this was my experience) before a cold-reset will put You back to business.
Good luck.
Ruud
Having the exact same problem as gary_b and having performed quite a few upgrades, I can confirm there is absolutlely nothing on the screen. The unit will not go into bootloader mode or even able to do a hard reset. It is not recognized when plugged in the USB.
When connected to power and the hard reset procedure is done, the red charging light will come up for less than 1/2 seconds and disappear.
I tried all different combination to make it boot but nothing. If I could at least get it to bootloader more, I can revive it.
Feel very bad I cannot help here.
I was wondering Yesterday about one thing. IF, during all this upgrading process, the battery runs out, (as it does not seem to charge during upgrade process) will it show bootloader screen ?
Would it be possible to get a loaded battery from somebody to check yours ?
That is a good suggestion to try out, but I have been unable to find anyone that has that device. It might be simply a drained battery.
Mine got corrupted I think at the end of the upgrade right after I did a regular reset instead of teh power and reset procedure.
However, I would think that even with no battery in, the unit should power back up when plugged in no?
Maybe an idea for somebody who is doing upgrading now, and is in bootloader status anyway.
Take out the battery, but connect with USB to PC with ASync. Does the bootloader state show ?
I am sorry to not do it for myself, if You saw my desperate state Yesterday, You will believe that I am not willing to see that bootloader screen for some time, sorry.
Ruud
now i know what to do:
Nothing!!
I went to a service-point with my mda pro and there was nothing to do with it.
If this happens the complete memory is "killed". Like "format c:" and while format is running you switch out the power.
Thanks god: I got a new MDA pro because i did not tell them (in the store)that i tried an update!
But i called the service-line before anf they told me that there is nothing to do!
But thx
Wow, can't say that this is good informatuin for those with this problem, but very glad it worked out for You.
I ve had this problem 5 minutes ago. Finally a took out the battery. Then connect to AC and Red led is on. Then i put the battery, tried hard reset and message to confirm hard reset in the screen (wellcome to life, jasjar).Then i run radio update again and it's upgrading rigth now....buffffff
I almost suffered a heart attack when this happened an hour ago. Have found that the update works fine if the SD card is taken out... phew.
Hi everyone!
I have a bricked SGS2 from t-mobile. I can't tell exactly what has been flashed to it before, because it wasn't done by me. After flashing a rom it's bricked.
At the moment I can't get it into download mode or turn it on. The screen is black.
Things I've tried and they didn't work:
1. Charge the battery in case it's disscharged. (the phone is charging the battery, but there are no indication lights)
2. Remove battery>press vol up and vol down>insert usb cable.
3. I bought a usb jig and it also doesn't work. ( I followed all instruction how to get it work)
4. When I connect the phone to the PC (with battery or without it) the PC offers me to format the drive I inserted, and every 5 seconds the phone drive gets disconected and connected again after each time windows offers me to format the drive.
5. When I press the power button- nothing happens.
Anyone could help me? Has anyone sorted this kind of problems?
Hi all, I've been using XDA for years since the original O2 XDA's and I have never had to post anything as I've always found my solution. I'm hoping somebody can assist me with a problem I have on this stock galaxy tab 3.
The device was brought to me after being thrown down the stairs. I replaced the screen and built it back up,
Removed battery connector and reconnected = nothing happens
Press power = nothing happens
press download mode = nothing happens
press recovery mode = nothing happens
Plug USB into PC = nothing happens on PC or tablet
Plug in USB mains charger and it displays battery charging logo but it doesn't fill or animate the fill then it starts the samsung boot screen. It reboots and continues to do this constantly and never ends.
I've tried two batteries and both batteries work in another tab 3 but neither batteries changed how the device works.
Thank you for any advice in advanced!!
I just received a Tab 3 lite (SM-T110) for repair, it's having a similar problem.
It does automatically turn on when plugged into charger or computer.. It is stuck on a bootloop, requiesting a Kies recovery. It does reboot when given the three finger salute (center button, volume down, and power) - it will not enter recovery mode though - same firmware error message). The device is also full off or full on, no indication of it's it's recharging or no - let the battery run out, it's off - else it's on (does not turn on or off with power button). I don't have any info how it got into this state - most likely power loss during a firmware update, but haven't ruled out other possibilities (ie bad rooting job, a custom ROM upgrade went wrong, etc). I'm not 100% concerned about cause, but hopefully I can unbrick the thing.
Anyways, I loaded Kies onto my computer and put it into recovery mode and plugged it in - nothing. Exit the recovery mode of Kies, and all of a sudden the program goes nuts trying to connect and disconnect from the device. Hmm... Okay, disconnect it, uninstall Kies, install Kies3 and try again - same thing except it complains the device is too old when the program leaves recovery mode - but same thing otherwise - does not show up in recovery mode, connects and disconnects at huge rate when not in recovery mode....
Hmmm...
Now looking at the screen, it does indicate (in the upper left hand corner) that it's in ODIN mode... So my next step I figure I'll try ODIN (although I'm researching ODIN at the moment as I haven't used it before (never had to unbrick anything from Samsung prior to now).
Okay, that was painless - downloaded and installed ODIN 3.10.7, and then downloaded the latest firmware from Samsung, extracted the firmware, added it to ODIN's AP line, then hit start to push the latest firmware onto the tablet. Good as new again.
Hi.
I have a Xiaomi mi5s 64/3 GB in an endless bootloop. Here are the details:
The phone is:
rooted
bootloader unlocked
developer mode enabled
internal storage *not* encrypted
no MIUI account activated
USB debugging on
running the last EU MIUI 9.x development version (don't remember the exact version) with Android 7.0
has TWRP 3.2.1.0 and supersu 2.82
no password is set for unlocking the screen etc.
For some unknown reason the phone suddenly rebooted yesterday and got into an infinite bootloop cycle. I haven't changed any roms recently or done any such flashing. My google play automatic updates were disabled, but a few days ago I manually updated all the apps.
The only odd thing that happened prior to this bootloop, was that when shooting some photos with the google camera mod (same one I've been using for the past few weeks), 2 images were saved as corrupt unreadable files. But that happened a few hours before the bootloop suddenly started.
The current status is:
1. I cannot turn the power off (tried holding the power button, or power button + vol up and down for a very long time --> nothing).
2. I cannot enter recovery mode using vol up + power.
3. I cannot enter EDL using all 3 buttons.
4. If I hold volume down, it enters fastboot but automatically exits from it within 4 seconds (ADB and miflash cannot detect the device in this short period of time). holding the volume down button for a long time has a repating enter-exit-after-4-seconds from the fastboot graphics.
I waited until the battery was completely dead, than started charging it and the status described above was unchanged.
QUESTION 1 - restoring the internal data is my number one priority - does it seem possible here?
To be exact: I want the DCIM folder with the photos+ videos. What should I try now?
QUESTION 2 - I ordered an EDL cable, but am unsure if it supported for my MIUI version. if the EDL cable works, can I force the phone to enter recovery mode from within EDL?
If so - I guess I can copy the internal data to an external USB OTG flash drive I have (that works well with the phone).
If my data is restored, I will then move onto trying to reflash the phone, but at this point this is the least of my worries...
Thanks all.
Anyone?
Maybe it's a problem with the button? I would disassembly the phone and check the hardware.
bedson87 said:
Maybe it's a problem with the button? I would disassembly the phone and check the hardware.
Click to expand...
Click to collapse
I don't know - the buttons don't seem like they are stuck in any way. When I push them, they click back out as usual.
Update - I created an EDL flash cable by stripping the cable gently, exposing the green and black wires, and looping them together - connecting this cable to the phone didn't help either.
Maybe I need to wait for the battery to die so the phone will turn off, connect this cable to the phone, keep the power button pressed while I connect it to the usb port in my PC... what do you think?
I have the same problem with mi 5s which started after update. Don't know what to do.
Took the phone to a local lab - it was all due to a faulty power button module.
Hi users, recently I wanted to go back form miui pie to oreo using this thread : https://forum.xda-developers.com/redmi-note-5-pro/help/how-to-revert-miui-10-pie-to-miui-10-t3940244
I had some problems with flashing, phone got disconnected from pc during fastboot flashing (loose cable) and after reconnecting I couldn't flash anything so I restarted the phone. Now all I've got is black screen (the backlight works but I can't see anything) I can restart the phone when holding power button and doing the combination of power up and vol+, but it's the same. If I connect the phone to pc in this conditon nothing happens, I can't hear any sound indicating that phone is connected, nothing in device manager, I even disconnected the battery and tried the edl pins but it's the same result, pretty weird. Can anyone give me any hint?
Verity. said:
Hi users, recently I wanted to go back form miui pie to oreo using this thread : https://forum.xda-developers.com/redmi-note-5-pro/help/how-to-revert-miui-10-pie-to-miui-10-t3940244
I had some problems with flashing, phone got disconnected from pc during fastboot flashing (loose cable) and after reconnecting I couldn't flash anything so I restarted the phone. Now all I've got is black screen (the backlight works but I can't see anything) I can restart the phone when holding power button and doing the combination of power up and vol+, but it's the same. If I connect the phone to pc in this conditon nothing happens, I can't hear any sound indicating that phone is connected, nothing in device manager, I even disconnected the battery and tried the edl pins but it's the same result, pretty weird. Can anyone give me any hint?
Click to expand...
Click to collapse
You are in situation similar to me. https://forum.xda-developers.com/re...e-5-pro-unbrick-project-t3940446#post79743110
But I am still struggling with this phone, issue no resolved yet.
yawarniazi said:
You are in situation similar to me. https://forum.xda-developers.com/re...e-5-pro-unbrick-project-t3940446#post79743110
But I am still struggling with this phone, issue no resolved yet.
Click to expand...
Click to collapse
Yeah, but the point is, you can connect to pc and flash things and I can't do anything, I suspect my computer fried usb board or something on the motherboard bc it's impossible I can't get qualcomm hs-usb loader 9008.
As it turns out, after rebooting the pc, it doesn't boot anymore. Phone doesn't work and pc. Coincidence? formatting pc was needed (pc works now), could it be a virus or my power supply simply gave too much voltage to the usb? I was doing everything during the storm, y'know, thunders.. I don't know anymore, I tried even connecting to a different pc and the result is the same. I can't do anything on my phone, could it be broken usb board?
EDIT: It connects now in edl, I was shorting the pins incorrectly (can't touch the ground [shielding] while shorting the pins). Pls close this thread.