Develop Bugs

JasJar hangs on boot Splash screen after ROM upgrade

well i just downloaded and proceeded to flash the latest ROM from clubimate..
everything went normal, upgraded Radio, ExtROM, and CE ROM, then i was asked to unplug the device, and cold boot it, which i did.
after clearing the storage, the device reset, showed the splash screen, the version strings (latest ones) and stayed there.. i kept it for 15 minutes to no avail..
i reflashed again from the bootloader and still the same behaviour
Radio ROM takes 20 minutes to flash, EXT Rom takes less than a minute, then when CE flashing is done, i cold boot.. again it gets stuck on the boot splash screen
i tried a different PC, different cable, older ROM version.. all the same..
any clues as to what may have gone wrong here?
Thanks in advance

me too
Got the same problem and same description of proces

well,
i tried flashing the radio rom again, tried every mtty trick in the book and still got nothing.
eventually i've taken the phone to i-mate service center, and it's been there for a week
they said the motherboard is faulty and needs replacement, i'm suspecting the flash chip has gone bad.
now i'm not sure if this applies to all of us here with the same symptoms after the upgrade, but i really find it strange that after all these years with i-mate devices, upgrading, downgrading and flashing different roms, half the forum hits the same dead-end when a new update comes out from i-mate and they try to flash it on.
something is strange about the latest rom. i just wish i knew what it is

AntiProxy said:
...i'm suspecting the flash chip has gone bad...
Click to expand...
Click to collapse
you bet it is!
buzz

HELP PLEASE BUZZ
I have upgraded to rom JASJAR_WWE_13076_164_10900_wwe_ship
when rebooted I just get blank grey screen.
after messing about with mtty I got it so I can reinstall it again at last but then same problem.
Any I deas Buzz you da man
Cheer in advance
Jon

same problem here
damn, same problem with me
its not recognized by the pc and there is absolutely nothing on the screen
anyone found a solution for my thousand dollar paperweight?

AntiProxy said:
after clearing the storage, the device reset, showed the splash screen, the version strings (latest ones) and stayed there.. i kept it for 15 minutes to no avail..
Click to expand...
Click to collapse
I now have the same problem as well. I however received this through the trials and tribulations of getting my JJ into the damn bootloader...

[Help] White-Screen after 3-26 LVSW firmware flash

Sorry to open a new thread, but I want to ask is there any method to fix this problem apart from using Mitty?
I tried flashing LVSW 3-26 firmware using SPL 1.06 or the 1.1x, both gave me the end results of white screen.
I am newbie to Mitty and worry of bricking my device with Mitty.
Can anyone suggest what I could do to cast the white screen away?
Desperately in need of help.
Thanks

I see by the sorry for a new thread you have read
http://forum.xda-developers.com/showthread.php?t=299644
I am with you. Right now I would go to a different version. The previous LSVW or another build. I am trying the mtty thing but I am running vista and cannot get NBHextract to work.
If you do not want to risk it maybe holding off a day and checking back for an update. These guys are fast. Also like I said go to a different version. I flashed the revious LSVW os only and it worked 3 times in a row perfect

When you say white screen what do you mean?? You get a white screen and the device doesnt boot?? or the device has a white today screen?

people
for black 1.3 i will release two versions
one with SPL and OS (with RUU 3.6)
and
one with only OS using standard RUU (assuming you already have HardSPL)
this will give u an option

jasjamming said:
people
for black 1.3 i will release two versions
one with SPL and OS (with RUU 3.6)
and
one with only OS using standard RUU (assuming you already have HardSPL)
this will give u an option
Click to expand...
Click to collapse
Hell yes. Makes the guide clearer to make (i will mention the value of embedded HardSPL and radio though )

mrvanx said:
When you say white screen what do you mean?? You get a white screen and the device doesnt boot?? or the device has a white today screen?
Click to expand...
Click to collapse
The White Screen for me is i can see the HTC Flash screen, but the Windows Mobile screen becomes white without me even seeing it and the Today screen is also white also.

Also, i was wondering if using Hard-SPL might help?
Thanks

nope i am using hard spl and tried it still white screen

Me too....
I also got the white screen of death. lol.
i used the version that was posed on the main page. After the update and initial boot the white screen comes on.
I was able to bypass this after several resets. Then it will start the customisation process. After which it will restart and go to a white today screen with no icons. I do have the task bars at top and bottom but no dialer.
My fix. I went and dl RUU_HER_6.20.100.0_0.00.00.00_XDA_WWE_XBOW_Custom. I installed it and works like it did before.
I will wait till there is a fix for this...
BTW I have a cingular 8525

I WANT TO OFER YOU GUYS SOMTHING
those of you who got white screen do you have language on boot?
i mean do you have diffrent language pack that need to be boot when you make hard reset?
cause i notice that when my language pack boot with new rom igot
white screen the language pack stuck it
then i remove my language pack from booting then its ok!!

After 1 whole day 24 hours non-stop fidgetting with my device, still NO LUCK...
Flashed it so many times, but still white screen.
Anyone can help me out?
Thanks

HKFreak said:
After 1 whole day 24 hours non-stop fidgetting with my device, still NO LUCK...
Flashed it so many times, but still white screen.
Anyone can help me out?
Thanks
Click to expand...
Click to collapse
Think this should help, I did cut the quote down a bit.
mxlaser said:
After hours and sleepless night, and so many flashes i think the NAND in my dopod was hot enough to fry a breaky for me, i've come to the comclusion, i have 100%, no issue success with all ROMS, using 1.01MFG and MTTY flashing each part seperatly. Not one time has a white screen appeared, with ANY rom, and i've tested all the current WM6 roms.
I d/l'd and tried the latest LVSW rom (26/3) and have exactly the same issue when using the packaged RUU to install it. However, when i use MTTY, its perfect every time.
I would suggest the following steps
1. Load into the bootloader mode (HOLD POWER/OK buttons and press soft reset)
2. Flash SPL-1.01MFG onto your device (Read wiki info and file links here)
3. Once flashed, reboot and do step one again to get back into boot mode. You should now see your boot as 1.01MFG
4. Use NBHextract to extract 06_OS.nb file from RUU_signed.nbh file found in downloaded rom package.
5. Load up MTTY, follow steps in the wiki for the 1.01MFG on how to flash OS.nb (OS.nb is the 06_OS.nb file renamed to make it easier)
6. Once flash is complete, the latest rom is installed and you won't have a white screen
7. Now flash Hard SPL v4 onto your devic for safety reasons.
And this fix is EASY to do, 100% works every time.
Click to expand...
Click to collapse
It worked 100% for me first time.

Just for the record I used ROMbaker to get the 06_os.nb then just rename it to os.nb.
Also if you are not sure and feel nervous about bricking it, then just wait for a proper fix.
Finally I got the white screen a few times and everytime I flashed the previous LSVW os only the device worked perfect. From my reading Olipro may have found the problem haveing to do with bad blocks. Nothing major but I believe they are working on it currently.

If you follow these directions and install 1.01MFG, you can BRICK YOUR DEVICE with ANY mistake!
We're not talking about a brick that can be fixed either. You precious phone will become a paper-weight forever more! Really.
I DON'T CARE WHAT THE N00BS ON HERE SAY; FLASHING 1.01MFG IS **NOT** A RECOMMENDED WAY TO FIX THIS PROBLEM! DO NOT INSTALL 1.01MFG UNLESS YOU ARE OK WITH THE CHANCE THAT YOUR PHONE WILL BE BROKEN FOREVER!!

bubu23 said:
I WANT TO OFER YOU GUYS SOMTHING
those of you who got white screen do you have language on boot?
i mean do you have diffrent language pack that need to be boot when you make hard reset?
cause i notice that when my language pack boot with new rom igot
white screen the language pack stuck it
then i remove my language pack from booting then its ok!!
Click to expand...
Click to collapse
No, I have never installed any language packs on my phone. I use good ol' english.

HKFreak said:
After 1 whole day 24 hours non-stop fidgetting with my device, still NO LUCK...
Flashed it so many times, but still white screen.
Anyone can help me out?
Thanks
Click to expand...
Click to collapse
Just go back to a previous version of WM6.
It only takes several minutes to put back XDA- Live.

mzahiri said:
Just go back to a previous version of WM6.
It only takes several minutes to put back XDA- Live.
Click to expand...
Click to collapse
I tried going back to WM5 firmware.
Flashing the firmware is a success but I still got the white-screen-of-death.
Any other options?
Thanks

SPL-1.35.Olipro will be released shortly; this should address the issue of the whitescreen error, all those having problems under 1.30 should no longer encounter it if they were able to flash fine with old SPL's

Olipro said:
SPL-1.35.Olipro will be released shortly; this should address the issue of the whitescreen error, all those having problems under 1.30 should no longer encounter it if they were able to flash fine with old SPL's
Click to expand...
Click to collapse
Go Oli Go!

Question ?
Hi All,
Sorry N00b alert at this .. but very IT literate
Just a quick question off the cuff, what was the last(est) version (can you provide a link) that i can flash to now .. (not mucking around seperating stuff etc) that wont give me the white screen issue.
I am currently sitting on LSVW 25/3 1.38.10 radio and 1.13oli
Thanx test

Splash screen and bootloader

Hi everybody,
i've tried to flash HTC spalsh screen but i got an error during da process and now whenever i turn on da device it only goes to da bootloader screen (tri-color). i tried soft/hard rest so far no success. i tried to reflash da entire rom( schaps 3.54b) however it says ur device it is not connected !!! ( i guess bc i can't sync da device). i also read da thread about how to unbrick hermes but no result
i desperately need some adivce
IPL 1.04
HERM100
SPL 2.10 olipro

I've done the same. Only I have now the original splash screen. My device starts normally.
I don't have a solution for you........ But I wanted you to know that it will work if it goes oke!
Good Luck finding a solution

Bensat said:
I've done the same. Only I have now the original splash screen. My device starts normally.
I don't have a solution for you........ But I wanted you to know that it will work if it goes oke!
Good Luck finding a solution
Click to expand...
Click to collapse
mmm you mean u flashed da original splash screen instead of HTC and then it worked fine?

If you have hard spl (looks like you have) then try flashing from the SD card. (If nothing else has worked - read all the guides/threads)
Just save the nbh as HERMIMG.nbh (make sure you have not created HERMIMG.nbh.nbh) in the root directory of your SD card, and then hold the power and OK buttons on each side of the phone, whilst pushing the stylus in the reset slot.
Hold it in for a mo.
Sometimes take a few goes.
It should come up with a loading grey screen.
It will give details of the nbh it has found (ie mine only said OS), and says something like push the power button to update.
Thank God for Hard spl.
Did this for the first time yesterday after apparently badly cooking a rom. Got stuck on HTC screen not bootloader, but this sorted me out.
Big relief.

ooohh , big relief man that was hectic moments i ended up flashing shcaps 3.57a ROM because his 3.54b ROM doesn't have spalsh screen included. but there is one question remains unsolved for me and that is why i got error during flashing only splash screen??? could it be splash screen file was corrupt?
im happy my baby is alive again

I'd more like to know how to make a musicial start tone with the splash screen. example HTC's offical rom has a nice animated splash with a musical tone. I've looked at the templates and examples and there's plenty of easy to understand aspects of a still splashscreen but can't seem to find anything that shows how to craete an animated with music splash screen like HTC's
any idea's?

Failure to boot up, during/after upgrade to WM6...

I tried to upgrade my new UK T-Mobile Compact III to WM6 following the information/files at http://www.ipmart-forum.com/showpost.php?p=1375965&postcount=111, but I failed. Instead, I ended up with a failure to boot up and a freezing starting screen of T-Mobile.
I tried to access bootloader following the information at http://wiki.xda-developers.com/index.php?pagename=Artemis_Resets, but I was unable to get anywhere else apart from the T-Mobile starting screen, again. Similarly, I tried several of the suggestions at http://forum.xda-developers.com/showthread.php?t=313848, but again no lack...
Can you please help me on that asap? What can I do to make my device workable (in either WM5 or WM6)? I spent a lot of time reading various threats in the forum and in various places in the internet, but I didn’t manage to find a solution. I would be grateful for any help.

Download this,
http://rapidshare.com/files/19322112/HTC_1.12.405.01_026790_WWE_SHIP.rar
it's the original wm5 rom and you will be able to get your device working if you run it from your bootloader screen.
Reset the device with the stylus and hold the top left button. After a few seconds you will get a screen with 3 coloured strips on it. Once on this screen run the art_tmouk_11311001_024990_wwe_ship.exe.
Then look through this:
http://forum.xda-developers.com/showthread.php?t=311403
after using USPL you will be able to flash any of the wm6 roms.

Problem solved!
Thanks a lot! Your advice was valuable. I managed to make it work again and then I installed WM6 following this threat: http://forum.xda-developers.com/showthread.php?t=325295
Everything works smoothly now!

Help - my Diamond can't boot

Hi,
I have my Diamond over a year and all was great till one day, suddenly it can't load the OS.
After power on, the black screen with "TOUCH Diamond" appear,
then it shows the radio version in red at the right bottom of the screen and from there nothing happen.
I tried to flash several ROMs & Radios, including the original ROM from HTC site but nothing.
The process of flashing seems to be fine and in fill all the 100% bar,
then it restart like during regular ROM flashing procedure but still no boot.
I tried to flash other hard-spl and still nothing.
I'm really lost and I hope someone has an idea for a solution.
Thanks
sorry if it's not the right place for this topic,
I also put it on general Diamond post so this one can be deleted.

MTTY?
Have You tried MTTY utility. Maybe it could help you.
Manual:
http://forum.xda-developers.com/showthread.php?t=540290