Help Help Help!!! My pocket pc not working during the upgrad - MDA III, XDA III, PDA2k, 9090 General

I tried to upgraded my SX66 system and radio rom. When I clicked "next" on the Blue Angel Flash ROM Tool to start up upgrade, the pocket pc screen turned off and my desktop was diconnected with the pocket PC (activeSyn showed "Not connected". And the desktop showed up the message "Cannot recognize USB device". I took a look at the PPC, its backlight was off and only had a message "USB v2.07" showed up". I tried to reset the PPC, but it is not working anymore, only show the message "serial v2.07". Any one help please!!!

Yes, a search of the forums would have helped you...
Stop activesync trying to use USB, put the device into bootloader mode (the screen with serial 2.0 on it) and then connect it to the PC. It will switch to USB
Then, reflash it using the utility
Also, 3 posts saying the same thing in 3 different forums is a bit extreme, 1 post would have been enough for you to get a reply, or better yet, searching the forums.....

Related

Help Help Help!!! My pocket pc not working during the upgrad

I tried to upgraded my SX66 system and radio rom. When I clicked "next" on the Blue Angel Flash ROM Tool to start up upgrade, the pocket pc screen turned off and my desktop was diconnected with the pocket PC (activeSyn showed "Not connected". And the desktop showed up the message "Cannot recognize USB device". I took a look at the PPC, its backlight was off and only had a message "USB v2.07" showed up". I tried to reset the PPC, but it is not working anymore, only show the message "serial v2.07". Any one help please!!!
see your other post....
starrayfly: please try to choose the right place and post once. Otherwise you'll get odd replies all over the place.
V

Urgent Hellp is needed

My Pda 2k device i tryed to upgrade it from 2003 SE to 2k5 after pressing update the device restarted gived me a gray screen and typed on it seril and at the buttom v2.02 now i cant open the device each time i reset or heard rest this is the only screen appears to me i cant even connect to activsync please i need your help what to do to get my device back, this error message i recived (usb device not recognized aslo active sync didnt recognize it)
i need to add a point the device is not working on the USP connection as it have a problem only serial port to connect with the pc
i'm so new here please help me
not to worry.. you can perform a hard reset of your 2k3 version "power+reset" to get you back to at least a working device.. I have been through this and have had this happen to me as well.. try entering bootloader again "power+record+reset" and dock it fairly quickly and it should change to USB on the screen and PC recognize it... also for anyone reading this.. I would highly recommend plugging your cradle into a 5v power supply as I can only imagine most of the bricked BAs are probably due to a computer freezing and/or the PC shutting down power to the USB port only for a fraction of a second and hosing the flash up.
THx Man i will try i hop this will work :lol:

USB Device Not Recognised on Bootloader

I have a problem. My Exec is stuck on the bootloader screen. All I see is Serial at the top, and v1.00 at the bottom.
When I connect my exec via USB, the screen continues to say Serial (rather than switching to USB) and the PC I connect to 'installs' the device as 'unknown device' in device manager.
I've seen mention of the problem elsewhere on the site, but the only solution I can find seems to be to keep trying, and eventually it's recognised. So far, after three days of trying, it has not been recognised.
I am aware of Buzz tool to get the device out of bootloader mode, but that required a connection to be established, which at the moment, I can't do.
Has anyone got any experience of this, or any ideas as to what's causing this, or how this can be fixed? I have tried uninstalling the 'unknown device' from device manger, restarting the PC (and hard reset of the Exec) then reconnecting, but the same thing happens every time.
Any ideas would be appreciated, as I'm currently staring at a rather expensive paper weight.
Try this it shld work
hdubli said:
This is based on my experience with two UNis..one Exec and other JASJAR..both had same problem...this is how I solved :
-Put yr device in bootloader Mode
-Disable USB in Active Sync
-Now connect woth USB cable and open mtty utility
-Select the "WESUSB... " port
-You shall see a blank white screen..press Enter to get "USB>"
-Then type ( as BUzz has informed) set 14 0
(here I wud like to inform that after doing the above I did not get success so I typed set 14 10,then set 14 9 for two three times)
-Then I ran the ROM Upgrade directly(After enbabling the USB)
-I then followed the procedure as informed on the COngratulations Screen that is hold the two "-" buttons and soft reset and then pressed 0
-I got them back to normal..
I hope this helps to all my friends...Pls feel free..pls do not trouble our Buzz..he might be busy in inventing something more to our devices
Click to expand...
Click to collapse
Guru Meditation said:
I have a problem. My Exec is stuck on the bootloader screen. All I see is Serial at the top, and v1.00 at the bottom.
When I connect my exec via USB, the screen continues to say Serial (rather than switching to USB) and the PC I connect to 'installs' the device as 'unknown device' in device manager.
I've seen mention of the problem elsewhere on the site, but the only solution I can find seems to be to keep trying, and eventually it's recognised. So far, after three days of trying, it has not been recognised.
I am aware of Buzz tool to get the device out of bootloader mode, but that required a connection to be established, which at the moment, I can't do.
Has anyone got any experience of this, or any ideas as to what's causing this, or how this can be fixed? I have tried uninstalling the 'unknown device' from device manger, restarting the PC (and hard reset of the Exec) then reconnecting, but the same thing happens every time.
Just noticed your user name, I was a big Amiga fan a few years back, still fire up Amiga forever occasionally on my PC when I feel the need.
Any ideas would be appreciated, as I'm currently staring at a rather expensive paper weight.
Click to expand...
Click to collapse
Try it with a different USB cable or in a different USB port (don't go through a hub and if you've been using a laptop then try it on a desktop PC since some laptops have hubs built into them). If that doesn't work then you're out of luck as your Universal isn't detecting that you've connected to your PC and its time to send it in for repair.
Thanks Niketkumar - unfortunately it's the step before your suggestion kicks in thats the problem - the device won't connect to the PC, so when using mtty WESUSB..... isn't an option, only COM1 and COM2.
Shuflie, I've tried with three separate USB cables on a laptop and desktop (neither through a hub, and the same device has worked fine on both laptop and desktop before).
I fear a trip to the doctors is in order ...
Very frustrating because the PC sees a device, but installs it as unknown device. Anyone know if theres a Windows CE device driver that I could try and install as an overide (i.e. in device manager on the PC go to update driver and browse to a WinCE.inf or equivalent?)
Failing this, has anyone got any clue what needs to be fixed? Or how much it might cost?
i am stuck on the same problem and wondering the forum for almost 3 days now with no luck.... please help my device is in boot loader mood but not turning the serial to USB ......... please HELP.......
solution
Guru Meditation said:
Thanks Niketkumar - unfortunately it's the step before your suggestion kicks in thats the problem - the device won't connect to the PC, so when using mtty WESUSB..... isn't an option, only COM1 and COM2.
Shuflie, I've tried with three separate USB cables on a laptop and desktop (neither through a hub, and the same device has worked fine on both laptop and desktop before).
I fear a trip to the doctors is in order ...
Very frustrating because the PC sees a device, but installs it as unknown device. Anyone know if theres a Windows CE device driver that I could try and install as an overide (i.e. in device manager on the PC go to update driver and browse to a WinCE.inf or equivalent?)
Failing this, has anyone got any clue what needs to be fixed? Or how much it might cost?
Click to expand...
Click to collapse
Please follow the steps:
1. Plug in ur usb cable in bootloader mode while it is showing 'serial' and version 'x.xx'.
2. Soft reset by pressing Backlight+power+reset pin WHILE KEEPING THE USB CABLE CONNECTED
3. your phone will now reboot into 'usb' mode. Don't remove the usb cable yet.
4. Remove the Memory card while keeping the usb cable still connected and VOILA,your pc starts recognising your phone as Microsoft usb sync.
5. Do whatever you want to do now (upgrade)
Hope it solves the problem now.
Press thanks if it does.
Something else to try
Having had a few issues with my G3 Uni, I've been through my fare share of Uni bootloader issues. When I find that I can't get the 'serial' to go to 'USB', I normally find it's because I haven't taken the memory card or the SIM card out (usually the memory card).
Make sure your memory card is out, then try to enter the bootloader and see if this cures it. If it does, then use mtty and the command 'set 14 0'
This tells it to reboot on reset. if you were to use 'set 14 1' it would go back to the bootloader on reset.
my Htc hd2 t-mobile won't recognize usb on boot-loader mode
hey guys i have a big problem!!!! my Htc hd2 t-mobile won't recognize usb on boot-loader mode. Here is the story my phone was running android 2.3.7 cyanogen 7 but i wanted to update it to ics android 4.0.4, So to do that i restarted my phone while holding down the down volume button and the boot-loader with the three colors came-on saying serial but when i connect my usb cable it won't show usb. even when i tried to run the dft.exe it shows an error saying usb connection failed. BY the way it lets me access the sd card using the usb cable on my pc, so i don't know what the problem is. PLEAS HEALP i am begging u guys pleas!!!!!!!!!!!!!!
kaleb2954 said:
hey guys i have a big problem!!!! my Htc hd2 t-mobile won't recognize usb on boot-loader mode. Here is the story my phone was running android 2.3.7 cyanogen 7 but i wanted to update it to ics android 4.0.4, So to do that i restarted my phone while holding down the down volume button and the boot-loader with the three colors came-on saying serial but when i connect my usb cable it won't show usb. even when i tried to run the dft.exe it shows an error saying usb connection failed. BY the way it lets me access the sd card using the usb cable on my pc, so i don't know what the problem is. PLEAS HEALP i am begging u guys pleas!!!!!!!!!!!!!!
Click to expand...
Click to collapse
you have the wrong forum friends! This Htc Universal section
to update Android on HTC HD2, you can use the Clock Work Mod Recovery !! for more details should refer to this thread http://forum.xda-developers.com/showthread.php?t=1021837
I-MATE JASJAR hung
Guru Meditation said:
Thanks Niketkumar - unfortunately it's the step before your suggestion kicks in thats the problem - the device won't connect to the PC, so when using mtty WESUSB..... isn't an option, only COM1 and COM2.
Shuflie, I've tried with three separate USB cables on a laptop and desktop (neither through a hub, and the same device has worked fine on both laptop and desktop before).
I fear a trip to the doctors is in order ...
Very frustrating because the PC sees a device, but installs it as unknown device. Anyone know if theres a Windows CE device driver that I could try and install as an overide (i.e. in device manager on the PC go to update driver and browse to a WinCE.inf or equivalent?)
Failing this, has anyone got any clue what needs to be fixed? Or how much it might cost?
Click to expand...
Click to collapse
Hi every one,
i have a serious problem with my HTC I-MATE JASJAR what's blocked in white screen (Serial / USB) and i cannot do anything on it, no boot, no reset soft, no reset Hard, no upgrade.
The issue is related to:
I tried to upgrade Radio ROM from 1.09.00 to 1.12 and i'm using Windows 7 Pro and when starting Flash, my PC shutdown because an electrical issue and since that, i cannot boot my device, i cannot flash or reset, my device is hung on white screen with Serial when no USB cable bluged in the PC and USB when Cable is pluged.
I Tried many times to boot it but no response, it's still hung and nothing can move on it.
I Just have one detail: when i plug the USB cable in my PC, the device is reconised but when starting upgrade or flash, i have error 101, no connexion.
Plz someone help me
bechir2013 said:
Hi every one,
i have a serious problem with my HTC I-MATE JASJAR what's blocked in white screen (Serial / USB) and i cannot do anything on it, no boot, no reset soft, no reset Hard, no upgrade.
The issue is related to:
I tried to upgrade Radio ROM from 1.09.00 to 1.12 and i'm using Windows 7 Pro and when starting Flash, my PC shutdown because an electrical issue and since that, i cannot boot my device, i cannot flash or reset, my device is hung on white screen with Serial when no USB cable bluged in the PC and USB when Cable is pluged.
I Tried many times to boot it but no response, it's still hung and nothing can move on it.
I Just have one detail: when i plug the USB cable in my PC, the device is reconised but when starting upgrade or flash, i have error 101, no connexion.
Plz someone help me
Click to expand...
Click to collapse
look here
http://forum.xda-developers.com/showpost.php?p=5456317&postcount=6
the first point...
A lot easier than to root this device

Jasjar AKU2.0 ROM Upgrade Help

Got a Jasjar and it had AKU1.? installed. I tried to upgrade to 2.0 (JASJAR_WWE_20106_20301_11300_wwe_ship.exe) so that I can setup the push-mail. Bad choice by me, the upgrade completed and I just clicked the finish button (I recall it says something about hard reset PPC). So I did, and upgrade activesync to version 4.5.
Now my PPC doesn't even turn on, and my computer doesn't recognize the PPC either with an error saying "USB device not recognized".
Since I can't turn the ppc power on at all, computer can't recognize the ppc either, I have absolutely no idea on how to fix this problem. Anyone know what's the issue and the solution to this?

02 universal stuck in bootloader, cant fix.

I just got this thing and wanted to upgrade to WM6, i downloaded a new crossbow for the device and started to flash it following the instructions included with the upgrade. a little way thru the flash i got a connection error and now the device is stuck in bootloader. I tried the program to recover from stuck bootloader but on the drop down menu there is no USB option, all COMs only. But oddly enough the bootloader does say USB when plugged in.
I am running Vista which came with my new pc and I am hating it lately.
Please someone help me out, i dont really know what to do now. I really want this thing fixed and properly flashed to WM6.
thanks, Noob
hi
does the PC recognizes the PDA?
if when you connect your pda to your pc (with removed sd card) you see"usb" (on screen) it does
ihave problems like you (vista notebook,no usb on mtty......) but i can fix them
first download:http://www.wikifortio.com/141334/mtty.exe.zip (not from wiki)
(it has usb port for mee)
then
1. Take out the SD and SIM cards
2. Opened ActiveSync and go to file, connection setting and Un-check "Allow USB Connections". Then press Ok and close ActiveSync
3. Put in bootloader mode (Power + Light + reset) which brings up the "un-backlit" screen with "Serial" at the top and v0.XX at the bottom
4. Plug in USB cable DIRECTLY from PC to Jasjar (MAKE SURE NOT TO USE A USB HUB). You MIGHT then see a warning window complaining that an "Unsigned" device driver is being attempted to be installed. You will be prompted to either "STOP INSTALLATION" or "CONTINUE ANYWAY" - this warning can be safely ignored and so just click on "CONTINUE ANYWAY".
5. Open mtty utility / software
6. Select USB from the "Port" drop-down on the upper left corner of the dialog box and hit OK
7. Then another screen will come up. Hit enter and that will show "USB>"
8. Type "set 14 0" and hit enter. You will see some jibberish on the mtty utility which will again be suffixed by "USB>". Your HTC Universal will not seem to have done anything and should still indicate "USB" at the top, and "v2.01" (or equivalent) at the bottom. You can now close the mtty utility.
9. On the Desktop PC unplug the USB cable and re-plug it into the exact same USB port again. From this point onwards, you must use this exact same USB port to flash the ROMs of your Universal because failure to do so will most proably result in "Connection Errors" at the beginning of the flashing process when the RUU attempts to establish communication with your Universal. After re-pluging into the USB port, you can then run the ROM update JASJAR_WWE_13076_164_10900_wwe_ship.exe (or latest version)
9,1.if you can't upgrade your rom on vista see:
http://forum.xda-developers.com/showthread.php?t=291723&highlight=ruu+vista
i recommend you for first time upgrade your rom with"Beasty & Laurentius 2.09.01"
by me:right click on each ruu that you want to use go to properties intop bar
goto compatibility's tab in compatibility mode tik the run this program in...... checkbox then select"windows xp service pak 2"
10. It will go through the upgrade process with the 3 steps and "completed successfully" on the PC
11. Picture 1 below shows what the screen looked like after step 6 after disconnecting the USB cable, as 100% complete
for picture goto
http://wiki.xda-developers.com/index.php?pagename=Instructions for those stuck on Boot Screen
what hapened to you txkuntryboy ?
All you need to fix it is in the WIKI
Psi
i have the same probm i tride but it gives me in mtty programe that usb port cannot open
afash334 said:
i have the same probm i tride but it gives me in mtty programe that usb port cannot open
Click to expand...
Click to collapse
hi afash can you explain me your posision
hi said.
these are my information:
-windows vista home premium.
-using windows mobile device center.
ver. 6.1.6965
if i go to administrative tools i got:
-mobile devices with information:
-location: port_#0008.hub_#001
-microsoft usb sync. with information:
-driver date :5/31/2007
-driver version: 6.1.6965.0
my problem is my device stuck in boot screen with top usb and bottom
v1.01
i tryid what wretin above to uncheck the usb from sync then connect and i start mtty program i chose usb then ok give me this message
{usb port can not open }
thanx said and thanx wiki after long long search i found the solution
thanxx god
if want put your solution here for others
http://forum.xda-developers.com/showthread.php?t=313001

Categories

Resources