Got a Jasjar and it had AKU1.? installed. I tried to upgrade to 2.0 (JASJAR_WWE_20106_20301_11300_wwe_ship.exe) so that I can setup the push-mail. Bad choice by me, the upgrade completed and I just clicked the finish button (I recall it says something about hard reset PPC). So I did, and upgrade activesync to version 4.5.
Now my PPC doesn't even turn on, and my computer doesn't recognize the PPC either with an error saying "USB device not recognized".
Since I can't turn the ppc power on at all, computer can't recognize the ppc either, I have absolutely no idea on how to fix this problem. Anyone know what's the issue and the solution to this?
Related
I tried to upgraded my SX66 system and radio rom. When I clicked "next" on the Blue Angel Flash ROM Tool to start up upgrade, the pocket pc screen turned off and my desktop was diconnected with the pocket PC (activeSyn showed "Not connected". And the desktop showed up the message "Cannot recognize USB device". I took a look at the PPC, its backlight was off and only had a message "USB v2.07" showed up". I tried to reset the PPC, but it is not working anymore, only show the message "serial v2.07". Any one help please!!!
Yes, a search of the forums would have helped you...
Stop activesync trying to use USB, put the device into bootloader mode (the screen with serial 2.0 on it) and then connect it to the PC. It will switch to USB
Then, reflash it using the utility
Also, 3 posts saying the same thing in 3 different forums is a bit extreme, 1 post would have been enough for you to get a reply, or better yet, searching the forums.....
I am trying to upgrade from Ivan's ROM beta 13 to beta 15... Using the MAupgrade utility... however, everytime the utility resets the device to start the ROM update i get "USB device not recognised" from my PC and the update fails to start... eventually i get a connection error message.
This used to work just fine... however, recently i installed Activesync 4.5 Beta 2. Could this be causing the problem...? otherwise i'm not sure what else might be causing this...
I have also tried running the tool in bootloader mode with and without "USB connections allowed" ticked in Activesync but with no success...
Can anyone help me please?
Trying to clear registry before upgrading ?
Have you tried to clear registry before upgrading?
Hi Kassel, thanks for your response.
I have done a hard reset prior to upgrading... wouldn't that clear the registry?
If not please let me know what else i can do that might help.
Also, it seems very strange that i can't seem to do the ROM upgrade from bootloader mode.
I think i might be having a problem with GetDeviceData as it seems to stay in the "checking the information on your device... please wait" for forever when i try to upgrade from bootloader mode.
If it does come up, then the panel which says which version is on my device and which version it will be replaced by is blank?
This is not the case if i try to do it through activesync (with the device set up as guest).
What might get in the way of reading the device data? I made sure it went from serial to USB when i plugged the USB cable into the device and i have tried different cables...
My bootloader appears to be V1.00
hmmm... any thoughts?
Same here...
I also have the same problem.
I installed ActiveSync 4.2
Alse after having installed AS, the MTTY program doesn't see the USB port anymore, just some COM ports.
Same to me too
I have ActiveSync 4.5 bata at work (Which couln't upgrade ROM)
while my notebook with ActiveSync 4.2 work fine
Wow, it's great to hear that people are having the same problem...
Is it possible to back track with Activesync? Is 4.1 still available?
If not, i think i still have an older version running at home (i hope!)...
Is this definitely the issue then?
l_pete_l said:
I have ActiveSync 4.5 bata at work (Which couln't upgrade ROM)
while my notebook with ActiveSync 4.2 work fine
Click to expand...
Click to collapse
I have ActiveSync 4.5 and upgrading my Jasjar was successfully done with the ROM Version: (1.90.96 / 1.13.00 / 42.47.P8)
Sorry for not knowing, but is that one of the AKU3.2 ROMs. Not sure if it should make a difference, but just curious.
Also, did you need to use the MAupgrade Utility?
Cheers,
What happens with the USB drivers after installing ActiveSync 4.2
The strange thing is, that I tried connecting my MDA Pro to a PC without ActiveSync on board.
USB ports were visible using MTTY
I installed ActiveSync 4.2 and only COM ports are visible in MTTY, the USB port has vanished.
Can this be caused by the USB driver that comes with the ActiveSync install ?
If I put my device in bootloader mode, it sais USB on the PDA screen, but the utility for the ROM upgrade doesn't see the PDA and comes up with a device not connected error.
I would really like to try out one of the new ROM's by Ivan or JwRight, but am unable to, because of these USB problems.
So please someone help !!!!!!!!
I have the same problem... if i put the device into bootloader mode, "serial" changes to "USB" but the PC comes up with "device not recognized"...
Hi,
I've tried to upgrading with 9000_WWE_20202_20307_11500.exe found in this forum, but the notebook power off (bad economic mode also with the AC plugged) at the ExtRam update on 1%, just after the Radio.
But when I tried to re-run the program nothing change, just the bootloader v1.01.
Now the program recognize that there are nothing installed and ask to install all new Roms but after the second screen the utility tell me everytime: "ERROR 114 RADIO ROM UPDATE ERROR"
Somebody can help me?
Since the OS ROM is updated in the last step(to be precise, Step 3), you can easily take your device out of this bootloader mode.
1)open MS activesync on your desktop
2)go to connection settings and disable 'incoming USB connections"
3)run the exe(see the attachment)
your device should be out of bootloader mode.
PS: you can re-run the ROM upgrade again after your device gets back to life
Now my Universal is completly OFF
Hi, thanks a lot for your attention, I trye to follow your instructions but now after the Exit of bootloader, I can't update my Universal.
After read dozens of messages... I try to explain better my situation:
1) the first update was blocked by the power off in my notebook in the beginning on the ExtendedRam (1%)
2) after this I tryed to re-run the update program and this recognize NO ROM on my UNiversal and asking for replace with all new ROM, but a "error 114: Radio Rom update" don't let make the update. (that repeated many time and every time I tryed to reset, cold reset, warm reset... following all the messages that explained many different way to de-block the situation)
3) Now the screen is absolutly black and the PC say me taht the "USB Device Not Recognized"
Can you help-me?
Thanks for all...
I've search and now I've found the way
Thanks for your help, I have come back at bootloader mode and I can put in the wm6 version !
Bye
hi,
I've trie to update my qtek and during the update I've got an error.
And now I'm blocked on the boot loader mode...
I've tried the joined program, I disabled the USB connection,
and the program can't connect to USB...
I don't what can I do.
please help me...
seranares said:
hi,
I've trie to update my qtek and during the update I've got an error.
And now I'm blocked on the boot loader mode...
I've tried the joined program, I disabled the USB connection,
and the program can't connect to USB...
I don't what can I do.
please help me...
Click to expand...
Click to collapse
It's ok, after a reboot of my pda & PC, I can exit the bootloader.
Thks for this program
I was upgrading my Hermes 8525 with the latest black pro when my computer turned off. The Hermes boots into windows but displays a black back ground. There is no screen interaction and no buttons work. It does not active sync either or I would have reinstalled.
Is there a way to re-install a rom with out being in active sync mode ?
Also windows recognizes a USB devices but it does not recognize it as a Hermes any more
I need some advice and help
thank you,
Brian
tried to reenter the bootloader and reflash ?
http://wiki.xda-developers.com/index.php?pagename=Hermes_BootLoader
Also check out the WIKI site for upgrade problems HERE.
I've also found that have Hard SPL keeps a lot of problems at bay. You can get that HERE
imate ultimate 9502 stuck on "PLease reconnect to PC and run the upgrade again"
PROBLEM SOLVED!
hi guys,
any idea on this error, i have tried the posted solutions here, but nothing works. tried it on windows 7, windows xp. not connecting with activesync.
reason:
flashed 1.73 rom. then it went this way.
hard reset keys wont work.
when using XP, and running the 1.77, it will just say on the screen , "Sending data to mobile device, you can check the schedule on the device screen" but nothing happens..
on windows 7, it says Error 203. saying it was not connected via activesync.
any idea how to revive this phone.
thanks so much
disconect from pc
remove batery
put batery back on
put device to bootloader
connect to pc it should recognise it
run again eum
thanks mate,
but it did not work. still stuck on the please reconnect to pc screen.
br
Problem solved!
Problem solved!
here's what i do, i set the compatibility of WMDC to Vista, then set the compatibility of the 1.77 9502 image to Vista also. works like magic...
br