Help Help Help!!! My pocket pc not working during the upgrad - Upgrading, Modifying and Unlocking

I tried to upgraded my SX66 system and radio rom. When I clicked "next" on the Blue Angel Flash ROM Tool to start up upgrade, the pocket pc screen turned off and my desktop was diconnected with the pocket PC (activeSyn showed "Not connected". And the desktop showed up the message "Cannot recognize USB device". I took a look at the PPC, its backlight was off and only had a message "USB v2.07" showed up". I tried to reset the PPC, but it is not working anymore, only show the message "serial v2.07". Any one help please!!!

see your other post....

starrayfly: please try to choose the right place and post once. Otherwise you'll get odd replies all over the place.
V

Related

Help Help Help!!! My pocket pc not working during the upgrad

I tried to upgraded my SX66 system and radio rom. When I clicked "next" on the Blue Angel Flash ROM Tool to start up upgrade, the pocket pc screen turned off and my desktop was diconnected with the pocket PC (activeSyn showed "Not connected". And the desktop showed up the message "Cannot recognize USB device". I took a look at the PPC, its backlight was off and only had a message "USB v2.07" showed up". I tried to reset the PPC, but it is not working anymore, only show the message "serial v2.07". Any one help please!!!
Yes, a search of the forums would have helped you...
Stop activesync trying to use USB, put the device into bootloader mode (the screen with serial 2.0 on it) and then connect it to the PC. It will switch to USB
Then, reflash it using the utility
Also, 3 posts saying the same thing in 3 different forums is a bit extreme, 1 post would have been enough for you to get a reply, or better yet, searching the forums.....

Jasjar AKU2.0 ROM Upgrade Help

Got a Jasjar and it had AKU1.? installed. I tried to upgrade to 2.0 (JASJAR_WWE_20106_20301_11300_wwe_ship.exe) so that I can setup the push-mail. Bad choice by me, the upgrade completed and I just clicked the finish button (I recall it says something about hard reset PPC). So I did, and upgrade activesync to version 4.5.
Now my PPC doesn't even turn on, and my computer doesn't recognize the PPC either with an error saying "USB device not recognized".
Since I can't turn the ppc power on at all, computer can't recognize the ppc either, I have absolutely no idea on how to fix this problem. Anyone know what's the issue and the solution to this?

02 universal stuck in bootloader, cant fix.

I just got this thing and wanted to upgrade to WM6, i downloaded a new crossbow for the device and started to flash it following the instructions included with the upgrade. a little way thru the flash i got a connection error and now the device is stuck in bootloader. I tried the program to recover from stuck bootloader but on the drop down menu there is no USB option, all COMs only. But oddly enough the bootloader does say USB when plugged in.
I am running Vista which came with my new pc and I am hating it lately.
Please someone help me out, i dont really know what to do now. I really want this thing fixed and properly flashed to WM6.
thanks, Noob
hi
does the PC recognizes the PDA?
if when you connect your pda to your pc (with removed sd card) you see"usb" (on screen) it does
ihave problems like you (vista notebook,no usb on mtty......) but i can fix them
first download:http://www.wikifortio.com/141334/mtty.exe.zip (not from wiki)
(it has usb port for mee)
then
1. Take out the SD and SIM cards
2. Opened ActiveSync and go to file, connection setting and Un-check "Allow USB Connections". Then press Ok and close ActiveSync
3. Put in bootloader mode (Power + Light + reset) which brings up the "un-backlit" screen with "Serial" at the top and v0.XX at the bottom
4. Plug in USB cable DIRECTLY from PC to Jasjar (MAKE SURE NOT TO USE A USB HUB). You MIGHT then see a warning window complaining that an "Unsigned" device driver is being attempted to be installed. You will be prompted to either "STOP INSTALLATION" or "CONTINUE ANYWAY" - this warning can be safely ignored and so just click on "CONTINUE ANYWAY".
5. Open mtty utility / software
6. Select USB from the "Port" drop-down on the upper left corner of the dialog box and hit OK
7. Then another screen will come up. Hit enter and that will show "USB>"
8. Type "set 14 0" and hit enter. You will see some jibberish on the mtty utility which will again be suffixed by "USB>". Your HTC Universal will not seem to have done anything and should still indicate "USB" at the top, and "v2.01" (or equivalent) at the bottom. You can now close the mtty utility.
9. On the Desktop PC unplug the USB cable and re-plug it into the exact same USB port again. From this point onwards, you must use this exact same USB port to flash the ROMs of your Universal because failure to do so will most proably result in "Connection Errors" at the beginning of the flashing process when the RUU attempts to establish communication with your Universal. After re-pluging into the USB port, you can then run the ROM update JASJAR_WWE_13076_164_10900_wwe_ship.exe (or latest version)
9,1.if you can't upgrade your rom on vista see:
http://forum.xda-developers.com/showthread.php?t=291723&highlight=ruu+vista
i recommend you for first time upgrade your rom with"Beasty & Laurentius 2.09.01"
by me:right click on each ruu that you want to use go to properties intop bar
goto compatibility's tab in compatibility mode tik the run this program in...... checkbox then select"windows xp service pak 2"
10. It will go through the upgrade process with the 3 steps and "completed successfully" on the PC
11. Picture 1 below shows what the screen looked like after step 6 after disconnecting the USB cable, as 100% complete
for picture goto
http://wiki.xda-developers.com/index.php?pagename=Instructions for those stuck on Boot Screen
what hapened to you txkuntryboy ?
All you need to fix it is in the WIKI
Psi
i have the same probm i tride but it gives me in mtty programe that usb port cannot open
afash334 said:
i have the same probm i tride but it gives me in mtty programe that usb port cannot open
Click to expand...
Click to collapse
hi afash can you explain me your posision
hi said.
these are my information:
-windows vista home premium.
-using windows mobile device center.
ver. 6.1.6965
if i go to administrative tools i got:
-mobile devices with information:
-location: port_#0008.hub_#001
-microsoft usb sync. with information:
-driver date :5/31/2007
-driver version: 6.1.6965.0
my problem is my device stuck in boot screen with top usb and bottom
v1.01
i tryid what wretin above to uncheck the usb from sync then connect and i start mtty program i chose usb then ok give me this message
{usb port can not open }
thanx said and thanx wiki after long long search i found the solution
thanxx god
if want put your solution here for others
http://forum.xda-developers.com/showthread.php?t=313001

"Dead/No software" Qtek 9000! Need HELP! Please!

My Qtek 9000 just don't wanna turn on. When on USB, my computer says "can not find USB device"! But, when I click "power button" + "light button" + "reset button", on Qtek screen is "USB" on the top of the screen and "v2. 01" on the bottom, and computer finds "USB device".. Still, I don't know what to do and how to turn my Qtek on. Please help me. I need my phone!
Thanks..
Milos
Perhaps a hard reset could help
If not try to reflash a ROM
Instructions here:
http://wiki.xda-developers.com/index.php?pagename=Uni_ROM_Upgrade
Good luck,
Look, I CAN NOT turn my device on. I'm holdind the "power button" but NOTHING!
P.S. I need boot loader v2.01. Can you find it for me please?
I think that I need the corect ROM that I had before "this situation".. Can someone find me a ROM v2.01? Or tell me what to do!?
You are in bootloader mode with USB showing on the top and bootloader version on the bottom. Just connect to your computer and flash another ROM.
The numbers on the bottom are NOT version of the ROM, but a bootloader, just try different ROMs or try shipped ROM for your device, or better still READ WIKI.
enigma1nz said:
You are in bootloader mode with USB showing on the top and bootloader version on the bottom. Just connect to your computer and flash another ROM.
The numbers on the bottom are NOT version of the ROM, but a bootloader, just try different ROMs or try shipped ROM for your device, or better still READ WIKI.
Click to expand...
Click to collapse
Hey Enigma your 500th post LOL ...
and EMO_Raver as you said when you connect your device to computer there is usb onthe top and v2.01 in bottom so it means you have G4 device and you can flash a uni rom G4 one....see instruction in first post by Orb3000...
I was trying to flashi it, but even my PC finds Qtek as new device, when I want to chose "USB" in "port" menu (in mtty), there is only com1, com2 and com3! There is NO "USB", so I cannot flash it!
And when I just click on the "new ROM" icon that I dowonloaded here I always get: ERROR 101 - CONNECTION ERROR
Pleace Check:
1. Your device is properly connected to the USB cable or cradle (of corse it is, my PC founds it as new device)
2. Your USB cable or cradle is properly connected on PC (same as in first, cable is 100% connected)
3. Your device is turned on (it's in booter mode, USB on top and v2.01 on bottom)
So, what is the problem. Someone told me that my softwere died, so I need to "feed" my Qtek with new software, new ROM. Is that a problem? How to do it? HOW TO START MY PHONE AGAIN?
I need help! Asap!
...
what OS do you have on your pc ? windows XP ?
If Vista or Windows Seven u must change driver of Microsoft USB Device ...
ANd be carefull of baterry .. if u will discharged battery u will have big rpoblem ...
FIXED! Thanks everyone!

imate ultimate 9502 stuck on "PLease reconnect to PC and run the upgrade again"

imate ultimate 9502 stuck on "PLease reconnect to PC and run the upgrade again"
PROBLEM SOLVED!
hi guys,
any idea on this error, i have tried the posted solutions here, but nothing works. tried it on windows 7, windows xp. not connecting with activesync.
reason:
flashed 1.73 rom. then it went this way.
hard reset keys wont work.
when using XP, and running the 1.77, it will just say on the screen , "Sending data to mobile device, you can check the schedule on the device screen" but nothing happens..
on windows 7, it says Error 203. saying it was not connected via activesync.
any idea how to revive this phone.
thanks so much
disconect from pc
remove batery
put batery back on
put device to bootloader
connect to pc it should recognise it
run again eum
thanks mate,
but it did not work. still stuck on the please reconnect to pc screen.
br
Problem solved!
Problem solved!
here's what i do, i set the compatibility of WMDC to Vista, then set the compatibility of the 1.77 9502 image to Vista also. works like magic...
br

Categories

Resources