Develop Bugs

Please help somebody

hi forum...
i own a Jasjar & very recently tried the o2 exec new rom on it.. i had it for a few days but didnt quite like it as much as the jj rom.
so i wanted to go back to the jj rom, but now neither is my ppc synchronizing with the laptop nor is it allowing me to revert if i put it in bootloader mode.
i tried synchronizing after deleting the partnership also.
it gives me a country id error when i put the ppc in bootloader mode & run the ROMupdate Utility. i have extracted the contents of the .exe file into a folder as i wanted to use the new radio 1.06 along with my original jj roms.
PLEASE HELP ME
mOrph

I am not sure, but:
if you managed to change from jj to o2, this means that you were using an installer that was not checking for the ID of the device, if not it would not have worked. (maybe you were not aware of this)
If now you are reinstalling the original JJ files from the shipped rom with the original installer, i imagine that this installer does not recognise the device and gives the country id error.
So what you would need to do is change the original JJ installer to the NoID installer that you used in the change from JJ to O2.
So you need to extract the installation file and in this resulting folder you will have to replace the JJ installer with the one from the O2 installation. Then it will not ask what kind of device is connected.
In case you knew all this and did it anyway, then I apologize (and probably have no other idea how to help you..lol)
Andy

MaUpgradeUt_noID.exe error

Apologies in advance for the newbie question.
I have a new SPV-M5000 locked to Orange. I think I have all of the files that I need to unlock it, and using all three hands I managed to get it into bootloader mode, but when I try to run MaUpgradeUt_noID.exe I get the following error: "MaUpgradeUt_noID.exe is not a valid Win32 application"
I hope that I am making some kind of really dumb (and therefore easily fixable) newbie mistake here. Any thoughts?
Thanks in advance.

Upgrade utility
Hi.
I have the same issue and posted the following on Buzz's site (buzzdev.net) over a week ago but have had no replies. Hopefully someone with an answer will reply to you here?
Quote:
Having read pretty much all the forums on Universal software optimisation starting with craigiecraigie4's excellent guide at http://forum.xda-developers.com/viewtopic.php?t=31697&postdays=0&postorder=asc&start=0 and extensive reading on the wiki site and of course Buzz's brilliant work throughout this and other sites, I finally feel ready to take the plunge with updating my new o2 xdaExec using o2's 1.30.107 WWE ROM, Dopod's 1.11.00 Radio and my own Extended ROM creation (yet to be made as I want to do 1 bit at a time). I thought I'd put Jasjar's extended ROM (164 I think) on until I have got use to modifying the Ext ROM image as I want.
However, I need to use Buzz'y MaUpgradeUt_noID.exe program as the standard installer is telling me there is a country error. Fine, so I have that downloaded BUT when I try to run it, my Windows XP system tells me that it is not a valid win32 application. Am I missing something here? Have I downloaded the wrong program or is there a problem with my XP? I don't appear to have this problem with other programs.
Hope I have included enough info for someone to tell me where I am going wrong.
HELP................
Unquote.

I have just downloaded a version from this forum (about half way down) - I haven't had a chance to test it yet but it IS different and if I run it without connecting my Universal, it does run the program but fails as no PPC device connected so it may be the better version. I will try it tomorrow but if you test it first, let me know
http://forum.xda-developers.com/viewtopic.php?t=54210&postdays=0&postorder=asc&start=25

O.K., that file seemed to do it.
I have now flashed my ROM with the latest non-Greek QTEK build, UNI_QTEK_13077_176_10900_WWE_Ship.exe, and then copied UNI_Unlock_v1.exe onto a SD card and ran it. I got a successful unlock message.
However, when I put my SIM into the phone, it booted up to a plain screen with a title bar of "Simlock" and the following message: "Network is locked, Please input unlock code".
Did I miss a step somewhere? Is it possible that the SIM itself could be locked (it's a brand new Cingular SIM) somehow?

Yes you did miss a step, in fact you missed lots of steps.
Go back and read the readme.txt file that came with the unlock program, everything is explained very clearly in there what you need to do!

Corrupt Charmer (PM200) upgrade help

Guys, my phone is dead and I need a little help please.
I have a T-Mobile MDA Compact II and have mistakenly (why it worked I don't know) 'updated' it with a Prophet firmware release. This progressed as I expected but was I since discovered completely wrong. My phone now shows a black screen with Dopod logo on boot and then hangs.
I have since found this site (looks good btw!) and subsequently the ftp area. I've downloaded the correct firmware for my phone, reset into the three colour screen and kicked off the Romupdater for the proper version I believe to be for my phone. With the 2 releases from ftp (one in that directory appears to be only half a zip file) they appear to be uploading but there is no change with the black screen problem.
I'm now stuck and am hunting for options. I'm more than happy to help myself but can someone explain what I need to do and start me on my way to fixing this.
All because it hangs from time to time when I run up too many apps on it.
Thanks in advance
Andy

Tell us what ROM you are using and which software you are using to perform your ROM update.
Anyway, it is weird that the Prophet ROM doesn't work on your phone. Keep this low tone, but I've done a Prophet ROM flash on my Charmer before. Everthing works well except the camera, that's why I flashed it back to the original ROM. I won't advise others to do so, there seems to be a few 'fatal' cases. I'm not sure, probably because it is compatible with the earlier Prophet version.
UPDATE: Nevermind, you seems to have the information. Good if you can stick to the same threat to avoid confusion. To others, please refer to
http://forum.xda-developers.com/showthread.php?t=275337&highlight=

At work and I've left the phone at home but I believe it was something like 2.3.15 (i.e. upgrade from v1 to v2)

Correction, it's SPL 2.15, IPL 1.12.
I have seen a post on Hermes bootloader access over USB using Mtty and now have access to the cmd> Can someone help me perform a bootloader based ROM downgrade to known working or deleting the image that is there?

Have now found the awizard utility, which file type does awizard need to be fed via the ROM directory?
Yes I'm a newbie at this and shouldn't have messed with the ROM update but I'm an I.T. guys by trade so if you can feed me the info I need I should be able to follow instructions
Phone is still 'dead' though.

It needs
XXX-OS.nba
XXX-Radio.nba
XXX-ExtROM (directory wit Ext Rom stuff)
You ought to get these from the FTP. I've myself uploaded a Charmer original UK ROM T-mobile, it should be still there is no one messed with it.

Hmm, I've missed something then. I put the .nba files into the ROM directory and then run awizard and hit w. Where I would expect to see a list of files with numbers there isn't any.
What I miss?

the dir structure of the aWizard looks like the attached, where you have the ROMs under the "ROM" dir and Ext ROM. Where the aWizard directory has the aWizard.cmd file.

Can someone provide a split up (i.e. seperated nbf files) for the Charmer or the correct memory addresses to punch into nb2nbf to create my own?
The images seem to have been removed from the FTP site and I'm in position to de-brick my phone!

O2 Xda Zinc, How To Enter Bootloader,Plz?

I have a completely dead O2 Xda Zinc..probably caused by software...can someone tell me how to get to bootloader mode so I can try to update rom?..thanks

you need to have the abi files update for your O2 zinc that need only to load to your mini SD. and after power on it will automatic detect by your zinc

windelas said:
you need to have the abi files update for your O2 zinc that need only to load to your mini SD. and after power on it will automatic detect by your zinc
Click to expand...
Click to collapse
i have a similar problem with a dead O2 XDA Zinc...where do i get the abi file or can i make one from the wm6 upgrade file (Xda_Zinc_RM3070712_WWE_ExtV2.8.0.exe) that i download from the official website

the abi file can be found inside the exe but i dunno how can u extract it since if u use any extractor it will not give u the abi file ... also if u hv the raw rom & want to extract the rom also u will hv difficulty in extracting it
that is the problem that i am facing now

you can extract abi file from Xda_Zinc_RM3070712_WWE_ExtV2.8.0.exe by
1. connect o2 zinc with usb
2. flash your o2 zinc by exe file
3. when complete flash don't push finish button
4. select to view hidden files in folder that you put exe file
5. finally you will see marsii_g4.abi
goodluck & sorry my bad english

the .abi file in rapidshare
http://rapidshare.com/files/91371327/MarsII_G4.rar.html

unable to open registry key
hi kindly help me with my xd zinc problem w/ rom6. My unit suddenly crashed while in standby mode then i reset it then the setup was changed. the programs i installed suddenly became resident applications. Meaning ithey don't appear anymore in the storage memory unlike before that i can easily uninstall them. Now i dont know how to install them to install new softwares because the memory is low. then a message error "unable to open the registry key" appears everytime i reset.
What happened and what should i do?

ronald_di said:
hi kindly help me with my xd zinc problem w/ rom6. My unit suddenly crashed while in standby mode then i reset it then the setup was changed. the programs i installed suddenly became resident applications. Meaning ithey don't appear anymore in the storage memory unlike before that i can easily uninstall them. Now i dont know how to install them to install new softwares because the memory is low. then a message error "unable to open the registry key" appears everytime i reset.
What happened and what should i do?
Click to expand...
Click to collapse
reset meaning soft or hard reset?

hard reset or soft reset both does not do any good to remove the error message "unble to open the registry key" and to just reload the orginal applications and remove the others

ehmmm ... sad to say maybe u hv to flash the rom

how do i flash the rom?

download the official rom from seeo2 and then make sure ur dev is fully charged ... sync it wz ur pc using active sync then execute the rom (.exe file u hv downloaded)
good luck

Hi guys,
I've already upgraded to WM6 for my Zinc, but I'd like to have an original ROM in case I need to flash back when something's wrong. I checked seeo2 but I can't find it.
Pls tell me where I can find this original ROM (WWE) ???
Thanks

LeoDH said:
Hi guys,
I've already upgraded to WM6 for my Zinc, but I'd like to have an original ROM in case I need to flash back when something's wrong. I checked seeo2 but I can't find it.
Pls tell me where I can find this original ROM (WWE) ???
Thanks
Click to expand...
Click to collapse
original rom? WM5 ... u can get it at the site also

cruzzmz said:
original rom? WM5 ... u can get it at the site also
Click to expand...
Click to collapse
You mean the WM5 ROM on seeo2? It's still an upgrade ROM, not the original that comes along with the device at the beginning.
Anyway, I'm a newbie so please advice how to 'downgrade' from WM6 to WM5? Is this similar to the process upgrading from WM5 to WM6 (you just sync the device with PC, run the .exe file on the PC and let it go)?
If it's not, please kindly give me detail instruction
Many thanks

how do I downgrade my 2750?

I have PDAVIET rom on my 2750 - version 5.2.00H on the boot rom.
I want to go back to the HP version of Windows 2003. So, I unpack the files from HP (SP29856 - fresh download from HP), perform a clean reset of the 2750 and start the "downgrade".
When it starts transferring the data, what I see on the Ipaq is a new window called FUU with "Hello World" right in the middle. The upgrade seems to proceed OK - but the system stays on WM6.
So, what is going on? Where is this FUU coming from and why isn't my Ipaq being put into boot mode?
Any help appreciated

I get exactly the same thing as Alan trying to downgrade my hx2795 using the same ROM (SP29856.exe) from HP. Yeah I know the ROM is for the 2750 but the hardware specs look very similar between the 2750 and the 2795 so I was hoping I could use the ROM to downgrade from WM5 to PPC2003.

The rompaq is for all versions of the HX2000 series so it is designed for us. Something else is going on which we don't understand. Anyone elso got any clues?

alan sh said:
I have PDAVIET rom on my 2750 - version 5.2.00H on the boot rom.
I want to go back to the HP version of Windows 2003. So, I unpack the files from HP (SP29856 - fresh download from HP), perform a clean reset of the 2750 and start the "downgrade".
When it starts transferring the data, what I see on the Ipaq is a new window called FUU with "Hello World" right in the middle. The upgrade seems to proceed OK - but the system stays on WM6.
So, what is going on? Where is this FUU coming from and why isn't my Ipaq being put into boot mode?
Any help appreciated
Click to expand...
Click to collapse
After the update did you perform a clean reset? Cause when I downgrade to wm5 from wm6 I mention that nothing seems to change(the device boots in wm6) until I perform a clean reset.

I have done many upgrades on both my 4700's and my 2750. Each time, whether it is using the HP method, or Chris's bootloader program, the Ipaq ends up in bootloader mode before the upgrade starts.
On this occasion, it didn't. I got a program called FUU starting up - and I could access the today screen etc while the flashing was apparently working (the HP utility was gayly counting up the percent numbers). At the end of it, Activesync happily reconnected to my old profile.
I did also try a hard reset - but that still came up with WM6 as the base O/S.
Since BOOTLOADER itself will not work either, I think the latest rom upgrade on there has screwed something up - not sure what, why or how.
Alan

Yep, what Alan said. The HP update utility apparently thought it was updating the device but the device was just showing the FUU "Hello World" window. And during the alleged update I can go to the Today screen and access my programs.
If I hadn't downloaded this directly from HP I would think this was a joke.
I am able to re-flash WM5.0 to my hx2795 using sp33752.exe downloaded from HP. Everything works as expected, the HP utility puts my 2795 into bootloader mode before flashing the device.

I cannot find sp33752 - can you give me a pointer?
Thanks
Alan

Hmm... I just tried searching for sp33752.exe on HP's support & drivers webpage and it found it. Otherwise try:
http://h20000.www2.hp.com/bizsuppor...x=sp33752.exe&pc=0&sc=1&nh=10&rf=0&lkc=1&lk=1
Any luck with downgrading to PPC2003?

Many thanks - I'll try that sometime today and see what happens.
Alan

downgrade
Hi,
I'm trying to do the same. From some searching around I found out that what you need to do is use the WWE-hx2000_PPC03_downgrade.exe program which comes with the WM2003 upgrade CD.
I don't have the cd, and I have problems with P2P (it's avail both on torrent and ed2k), so if you get that file, and it works for you it'd be wonderful if you can upload it to rapidshare or something and post a reply here.
Good luck and cheers

I tried that SP - get the error "Could not initialise the device".
My Ipaq is in the cradle and activesynced to my PC.
So, it looks like i am stuck with this WM6 version. Something about it has stopped any form of upgrade or downgrade.
Alan

So, next thing I tried is to copy the FUU.EXE file to the older SP directory and run that. But all that does is appear to download the nbf file, but the IPAQ hasn't gone into bootloader mode, so nothing happens.
I think what I am missing is why we need these files (RUUClientdriver.dll, FUU.EXE etc) and what changes in each of the OS upgrades to require a different version. Any one know these sorts of answers?
Alan

success!
I found the file (http://rapidshare.com/files/17084671/WWE-hx2000_PPC03_downgrade.exe) and succeeded to downgrade to 2003.
I had to reset to bootloader mode (contacts+itask buttons+reset -> connect to cradle -> calender button*) and then run the hpRUU.exe from extracted directory (c:\ipaq\hx2000) and it works like a charm.
hope it helps. g'luck
(* contacts - 2nd from left, itask - 4th, calendar - 1st.)

That seems to be doing something. I put it into bootloader mode and it's flashing. 66% through and the bar on the Ipaq agrees.

Success!
Worked for me too! Thank you spring777. Now I can run PPC2003, WM5 or WM6 on my hx2795. This is such an awesome forum.