Hi guys,
New here so please be gentle. I have an Orange SPV C500:
Typhoon
IPL 1.00
Typhoon
SPL 2.00.0012
Typhoon
And so more info. I have the WM5.0 ROM and followed the instructions, load MTTY hit enter and up pops the CMD> prompt type l c:\john.bin being the filename of the ROM (where should this be saved, locally in C:\ on my drive) and all I get is this error message:
clean up the image temp buffer at 0x8C080000 Length 0x01B00000
MTTYDownloadImageNot allow operation!
Error : DownloadImage return error (code = 0xFFFFFFFF)
Having done various searches and reading some posts I can't really work out what the problem is. If someone could point me in the right place to either read something or tell me I would be very grateful.
My SPV is the one with the version 10 media player.
Many thanks, John
hi
where did ypu get the WM5 rom>?< if you tell me where to get it,i will try it and maybe i could help you you can send me a message with the rom link if you want,
lee J
Related
Hello everyone, i hope someone knows what the hell my JasJar bootloader have, since i'm trying to flash my device without success.
I've searched everywhere in the forum but found just a message with no reply.
First of all, i've unlocked my jasjar, it's now a superCID device. Or well, i guess so, since i can exec lnb commands.
Here you are the "log" from mtty:
-------------------------------------------------------
USB>task 32
Level = 0
USB>info 2
HTCS00000000 î¢-HTCE
USB>lnb c:\image.nb0
:F=c:\image.nb0
:A=70100000
:O=00000000
:L=FFFFFFFF
start NB image download
Fail to synchronize with the host (1)
USB>
-------------------------------------------------------
Using the "l" command jasjar hangs and MTTY claims a timeout in \\\wcehUSB1 or something after 5 minutes.
Any idea? I've tried with USB2 and USB1.2, tried differend PC models and differend baud but nothing change.
The "info 2" returns a strange SuperCID message. 2 bad.
Any advice is appreciated!
----------Refresh------------------------
I've also tried to upgrade bootloader to v1.1 but still have same issues...
Hi all thanks for looking at my thread.
I'm try to upgrade my Dopod D810 and i encounted a problem and would really like some help here.
The steps i thought i should take were the following
Run...
Unlock and CID Unlock
HardSPL
Radio
ROM
However, after running the Unlock and CID Unlock, i tried to run HardSPL.
But i come accross the "ERROR [246] DEVICE NOT RESPONDING" when i run the ROm update utility.
On the PDA with the 3 color screen
TRIN100
IPL-SSPL by Des
TIN100
SPL - 1.07.ds
and in the white "USB"
what have i done wrong? should i have no ran the UNLOCK and CID Unlock? if so how do i revert this? and what are the correct steps to take to upgrade this?
I am a hermes user and i've done exactly what i did to my hermes to his one.
Please help me.
Kind Regards,
Jason
---------------------------------
guys please, i tired reading the wiki and it told me to run SSPL-TRIN on my device.
i ran it, tired running the utilites again and i get the same problem.
the wiki and text documents says that as long as my SPL ends in a ".ds" i should be able to flash any rom without a problem but i still cant.
all i want is to have a english ROM and the current radio
please help masters. i keep getting "ERROR [246] DEVICE NOT RESPONDING" when i try to flash LVSW lastest rom.
kind regards,
jason
----------
I have been able to upgrade the radio to 1.41.
but i still get ERROR 246 when i try to upgrade the ROM or HardSPL
I'm waiting for help and will be very greatful when someone responds.
Kindest regards,
Jason
have you tried to run the RUU again (leaving the device connected in bootloader, tri colour screen) after you get the error?
Same problem here...
Alternative flashing method.
I just can tell I success using MiniSD with TRINIMG.nbh and execute SSPL-TRIN.exe to flash it. Hope this help. Read Wiki for details.
EDIT
ok i understand that you are suggesting that i use my SD card to Flash the ROM in.
If this is successful i will be greatful but will i have to do this everytime from now on rather than through the computer?
jason
racerx_ said:
have you tried to run the RUU again (leaving the device connected in bootloader, tri colour screen) after you get the error?
Click to expand...
Click to collapse
Ok so i've tried to flash a ROM/HardSPL using the SD card.
i;ve rename the file to TRINIMG.nbh
and then i;ve loaded it in to the bootloader.
however i get a quick flash of a grey background with the word "Loading" and then it just goes to the tri color screen and nothing happens.
the Tricolor screen shows
TRIN100
IPL-0.50
TRIN100
SPL-1.20.Olipro
(white area) Serial(or USB)
Please someone help me out.
a member has mentioned that it is because i do not have Super CID and i should run the unlock. but i have done so.
please guru's of trinity! help me!!!
Personally, I've never been able to flash my phone from the SD card. Never tried before Hard-SPL, but certainly since it just does not work. Need a Windows XP machine (my vista 64 bit won't work - can't find the 64 bit driver for USB bootloader mode). Find yourself a windows pc!
nealed said:
Personally, I've never been able to flash my phone from the SD card. Never tried before Hard-SPL, but certainly since it just does not work. Need a Windows XP machine (my vista 64 bit won't work - can't find the 64 bit driver for USB bootloader mode). Find yourself a windows pc!
Click to expand...
Click to collapse
My attempts with the SD have not work, when i put the SD card in and put it in to boot loader, i get a quick flash of Loading and its just stuck on the tricolor displaying
TRIN100
IPL-0.50 (could this be the problem?)
TRIN100
SPL - 1.20.Olipro
(white area) serial
i do have a windows XP home machine.
man this is stressing me out. please guru's help me out
ok i dont know how but i've some how been able to upgrade to the lastest LVSW. there is a god (i've always known)
how i did this was i was trying to run HardSPL again. It went in to the bootmode while the Utitlty on the computer gave ERROR 246.
So i thought i'd run LVSW, and what do you know? it work! and upgraded!
the question i have is
when i load the bootloader screen i get
TRIN100
IPL - 0.50
TRIN100
SPL - 1.20. Olipro
but then ERROR 246 occurs
i get
TRIN100
IPL-SSPL by Des
TIN100
SPL - 1.07.ds
So does anyone know what is wrong with my Trinty?
What do you bootloaders show?
---------------------------------
edit.
i;ve also noticed that after successful being able to upgrade to LVSW when i look at device info.
my radio hasnt actually upgraded, but back when i wasnt able to upgrade the rom it said i had 1.41.
but now i only have radio 1.16. but i have been able to upgrade to radio 1.41. now.
I just use TRIN-SSPL.exe and make it go into SuperCID Bootloader mode. Then it ask me to confirm whether I want to flash it, press [Power] to continue and it work.
MJRL said:
Same problem here...
Click to expand...
Click to collapse
are you using xp or vista? If you have vista try that on a windows xp machine. I have seen that many time on my p3600.
Just my 2 cents
First time with vista, but after read so many problems with vista i've tried with xp, but gave same error has jasonchiu, i'll try has he did,ignoring the error
Is it possible that other files on the MiniSD?
Try format the memory card and write the files.
I am running Vista so this the only way for me,
I used this method to flash WM5 and WM6.
On the memory card, only
TRIN-SSPL.exe and TRINIMG.nbh
and the device is not SuperCID.
while i upgrade to wm06 i get this error.
spl : 1.04
rom version :1.25...
please help me
I have got same inf when use RUU, but my spl is 1.01.
what shall we do
my
ipl :1.01
spl:1.04
radio :1.07
rom version : 1.25.207
now i cannot install wm06 tom my xda trion also htc hermes.
i dont know why i get this error. the usb is allways connected to laptop. and it is not deffect.
please help us friends.....
and i cannot succees bootloadermode by pressing power + ok and then stylus
why dont it go ?
and now it is ok. at the end i use wm06.
my steps was so.
if you start wm06 you get this message. go on insitalling on breck up.
ms corporation suggest to abort it.
you klick on "installirung fortsetzen" then you get an other error massege
error 264 when you get this error massage make a soft reset your hermes.
and i said before you are now on WM06.
Hi!
I was using Newplow's WM6 038 ROM with my N560.
Yesterday I tried to write another ROM(WM6 038 with 8MB pagepool) but during update got an error.. It said it just failed.
Now my N560 is stuck on booting screen(people climbing mountain..)
I tried Warm, Cold, Hard reset but with no luck.
Even the power button doesn't work so I had to remove battery. When I insert battery it powers on by itself.
I can enter bootloader screen by pushing power+record button so I tried to copy rom image file to SD card but it doesn't work.
I tried two ROMs(OS_213U.nbf from Original WM5 ROM and Newplow's) and 3 SD Cards(2GB SD, 1GB MicroSD with Adopter, 16GB SDHC)
Is there any recovery tutorial in bootloader mode?
Help me please!
Sorry for my English.
Have you tried flashing a ROM through the computer rather than the memory card? Try going into bootloader and flashing that way rather than the card.
The pagepool ROM is meant for N560s that have been upgraded to 128Mb RAM... have you upgraded the internal RAM to 128Mb? If you have not, then this may have caused your problem.
I had this problem when flashing to 038 normal RAM (from 035). A hard reset reset to the normal start screen, but nothing worked. However, trying a new burn with the Loox flash tool restarted the process and it worked. I found the cure was to make sure you hard reset the N560 before doing a burn. It appears to be that you have to do this to release enough RAM for the burn program to reside and for "working" storage. You may not have done this.
I suggest you try simply re-running the flashtool with SD/SDHC cards removed, battery in place, on the cradle via your PC, even though it appears stuck. The signals coming from the USB link may wake up the bootloader routine in the N560?
Solved the problem! Thanks for your comments!
I asked same question in Newplow's guestbook and the person who made pagepool rom answered. I used MTTY to revive my pda.
What I did is in below post. need translation
http://4pda.ru/forum/index.php?showtopic=55274
Hi all,
I have the same problem. N560 is stick on the himalaya picture. I tried to falsh from WM5 to new rom for Wm6 and after installation the pda stuked. So I did a warm reset and now only the start picture is apperaing. Problem is that battery is down now.
Can someone give more info on the process followed to revive the PDA ? I just cannont read russian (may be Jinsu77 ?)
Many thanks for support in advance
same problem here please please please someone help us
the only thing i can do is the l c:\os_213u.nbf on mtty program and nothing else happend to the machine
sorry for my english
read, and pay attention here:
[email protected]@p://a.mod-site.net/gb/u/newplow-1.html
POST 203.
It was me asking on Newplow's guestbook.
In case you're using Vista, you need some trick to be able to rom update. Read below.
http://www.modaco.com/content/windo...u-on-vista-it-can-be-done-the-ultimate-guide/
And then you need to download MTTY (I used version 1.42, got it by googling) and follow below steps.
(used google translation from 4pda.ru)
------------------------------------------------------------
For rom update without ActiveSync.
1) take this set of extract, copy it to the folder with the firmware.
2) copy the file os_213u.nbf example in C: \
3) You press the button Recorder + food and poke in the hole reset (Recorder button and hold until you eat dolphins)
4) plug the device to a PC, the Task Manager, shooting process - wcescomm.exe
5) Run mtty, choose Port: USB, connect.
6) If mtty caused an error and shut down, simply restart mtty, if not typed commands, then repeat the procedure with paragraph 3.
7) in mtty command, enter: (first letter in kommande - a little l l от слова from the word L L oad)
> l l c:\os_213u.nbf c: \ os_213u.nbf
Since the end of the process will be an inscription about the error, remove the device from the PC.
9) Run rom update, zhmete "next", until you see dolphins.
10), plug the device to a PC and program.
---------------------------------------------------------------
Hope this helps you all
in advance sorry for my english
I am doing all the instructions carefully and the mtty show this
Image Download Finish
OEMFlashWrite(A0000000h,8C200000h,1A0F023Ah)
Download Fails !!!
OEMFlashWrite error(12)
Error : DownloadImage return error (code = 0xFFFFFFFF)
the pda shos the dolphins and the full blue bar
after without change anything i run the PocketLOOX5xxFlashTool that i have in the same folder with the :
EnterBootLoader.exe
OS_213U.nbf (originally rom)
RUUServer.dll
RUU.dll
and the only thing i can see is that the PocketLOOX5xxFlashTool is trying to find the pda without any luck
also the pda is stucked in the same screen with the dolphins and the blue bar
do you see any mistake in this procedure
Helppp!!! please
tuluba said:
Helppp!!! please
Click to expand...
Click to collapse
have you closed EVERY process of activesync before proceding with mtty?
I close the wcescomm.exe and the rapimgr.exe is there anything else?
The pocket LOOX 5xx FlashTool cant connect with the N560 and at the and says that Error"The language in this Flash Image update (ENGLISH) differs from that on your device()!" and i have always english rom exept maybe from the last rom "the killer" with the 128MB rom that i dont know if it is an english or something else because the device never opens to see
After flashing in MTTY(don't care about error messages), you need to unplug your n560 from PC. And then proceed romupdate until you see the dolphin picture. Now you plug n560 to PC and cilck next and wait for a while.. Hope it works!
I change the language of the rom and it works
thank very much all of you
At all they have Probs with flash from SD Card: only use a Card with 512MB! I think a Card greater then can't read by the Bootloader....
hey.
i am compeletly new here. I have the same with my n560. I tried to upgrade to 128mb but after restart I see only climbing. I tried everything here but on dolphins afterr line is blue it is finished. that I am unpluging device. starting looxflastool for 560 and first is trying to connect by active sync and that when no connection made I see dolphins on left screen of flash tool window. than I am pluging again and after couple secs I see that: Error"The language in this Flash Image update (ENGLISH) differs from that on your device. I tried to change rom on every language but not working as well. PLEASE HELP
if that helps than i will add than on top when delfins i see on 560 is two lines. first is typed 2.14.G4 on second directly below is 2.15.
and when mtty 1.42 finishing flashing i see following:
Image Download Finish
OEMFlashWrite(A0000000h,8C200000h,0224002Ah)
Download Fails !!!
OEMFlashWrite error(12)
Error : DownloadImage return error (code = 0xFFFFFFFF)
Need help!!! Please!!!
I bricked my N560. I tried to downgrade from WM6 to WM5 and now I see only delfins and in the first line "2.14.G4" and in the second line "2.15"
What can I do?? How can I flash WM6 or WM5 ROM when there is no connection to the PDA????
ChrisDo said:
Need help!!! Please!!!
I bricked my N560. I tried to downgrade from WM6 to WM5 and now I see only delfins and in the first line "2.14.G4" and in the second line "2.15"
What can I do?? How can I flash WM6 or WM5 ROM when there is no connection to the PDA????
Click to expand...
Click to collapse
You can usually get back to the boot loader if you do a hard reset. I am sure you know how, if not you will find it in the FSC CDROM manual that came with the device. Let us know if this works? I have got stuck at this point too, so I know it works..... hopefully!
Dear all
I have this problem in my O2
when make upgrade I have this message
upgrade
Radio Stack
Please wait
and it's freez on this message then nothing
also when if I remove radio nbf and just upgrade nk.nbf
I have this message when it boot
no GSM
2.09.01_BL+
Please Help
o2 have tons of wm phones which type would prob be helpful for people looking to help you
personally I would try with only the radiostack as that seem to be the problem
then I would go here http://wiki.xda-developers.com/ locate my device and read it's wiki and maybe search it's forum
whan I make DOC format I Have this error
CMD3 for SD, it's OK, ready to get RCA from response.
SD: Detected one card
SD:ready for transfer OK
d.total_lba=1EB000
d.block_size=200
d.RCA=C160
d.drv_type=40000000
d.busWidth=1
Total card size=3D600000
Read singal error D3
SD read fail!
Level = FF
USB>task 28 55aa
Wait..
flFormatPhysicalDrive:status=29
DOC_format failed!
USB>
what can I do?
My phone type o2 Xda Exec v1.01
any one can help me