I had my original ROM back up to SD yesterday by performing a hard reset (hold on/off key then press the soft-reset button), then successful copy "CE + Boot to SD" to the card. But today, I can't perform the hard reset anymore. When I hold on/off key then press the soft-reset button, there is no option for me to choose, it only look like a soft reset. BTW, I did not neither change, modify or install anything since yesterday.
Anyone has any suggestion? Tks.
hhmmm never knew you could hardreset xda1's that way i believed that you needed to stick the stylus into the small hole on the otherside of the connector as in 1 hole for softreset and 1 hole for hardreset
Yes, the hard reset button on xda 1 is the tiny hole next to headset socket, push once, leave for 1 minute then push once more for fresh factory reboot. This procedure MUST be carried out after flashing phone.
I'm sorry I did call the wrong name for that procedure.
The problem is when I did successful unlock my Siemens SX 56 via ActiveSync by install the Special Edition rom 1.2, I couldn't enter the "bootloader" by hold on/off key then press the soft-reset button. Anyone pls help.
HI,
I had WM6 working on my Qtek 9090.. suddenly it hangs and I did a softreset (at first).. now it hangs at the startupscreen of WM6.. Hard reset doesn't do the job too :S...
damn.. is it dead now?
edit
---------------------
Qtek is running again after I did the following:
1. press on/off button - record button and soft reset button at the same time;
2. hard reset (on/off button and soft reset button at the same time.
and then it will run normally.
edit2
----------------------
problem is back.. when I shut the phone off (software) I can't get it back on... and WM6 will not start again...
It seems that when you want to restart your ppc you have to put out your sdcard. PPC is working again pffff
edit3
-----------------------
and yeah.. again.. after a soft reset after installing some software...
I'm trying to get some life back in the qtek...
.. and it works... I did the following:
1. press on/off button - record button and soft reset button at the same time;
2. hard reset (on/off button and soft reset button at the same time.
3. Put the qtek back in the cradle...
So.. Do not do a soft reset.. it's a pain in the butt...
After trying to upgrade my Dell, it no longer will turn on. Please tell that I really do not have that so called "300 dollar paper weight". Is there anything that can be done.
Ok, I have upgraded the rom on a HImalaya device (NOT an Axim) several times, and with those devices, after you upgrade the rom you need to do a SPECIFIC hard reset.
Pressing the normal power button or other buttons to wake it up doesn't work.
On our device it involves holding down the reset button, camera and record (it will be different on yours).
This takes us to a screen where we need to change three settings (such as cleaning the registry hives) before the device starts up.
You need to figure out what the specific reset combination is for your phone (generally it isn't the same as the hard reset you would usually use ETC on a Himalaya device the normal hard reset is reset plus power, but the reset after bootloader is reset, camera and record).
Hope this helps.
Thank you for you help. I got it working.
would you share how you did this?
Hard Reset for X50 is Hold Power Button and Push Reset Button
I was using from the device update the wmregoptimizer and it froze up my cellphone and when i did a softreset it won't start it frezees on the startuo screen can anyone help me what do? Active sync won't recognize it i don't know what to do
Hardreset (two context menu buttons + softreset)? Or try softreset again.
now its stock on the windows mobile screen after hard reset
it's working after hard reset thanks for your help pajousek
First of all - I am a Sprint customer with the Latest Htc Rom -stock
List of problems and actions taken.
Problems
Soft reset reboots with phone in Airplane mode.
When the end key is pushed not long pressed but pushed it puts phone into Airplane mode.
Battery run time is not about half or even less than it was before.
Actions taken
Removed battery for about 10 minutes and tried a hard reset. Got to the screen where you are supposed to hit volumn up to restore to original and well the volumn up button gets pressed but nothing happens. So after waiting for about 15 minutes I do a soft reset to get back to the HTC Sense screen (today screen). I take the phone out of Airplane mode cause from reset. I hit the volumn up button and it works fine. I tap the end key and it puts me back in Airplane mode.
So I reflash stock rom back in that by the way wouldn't go until I unlocked the phone with HardSPL. Apon first reboot it still boots with phone shutting down into Airplane mode. Turn phone back on then turn power off. Take battery out. Replace battery. While holding Talk ad End buttons I tap power on for hard reset. Goes through try colored screen then to the volumn up option screen. I tap volumn up and nothing still happens.
I'm looking at Task 29 but I am worried about the volumn button not working.
Anyone have any ideas on what direction to take. Thank you
Hootyhoo said:
First of all - I am a Sprint customer with the Latest Htc Rom -stock
List of problems and actions taken.
Problems
Soft reset reboots with phone in Airplane mode.
When the end key is pushed not long pressed but pushed it puts phone into Airplane mode.
Battery run time is not about half or even less than it was before.
Actions taken
Removed battery for about 10 minutes and tried a hard reset. Got to the screen where you are supposed to hit volumn up to restore to original and well the volumn up button gets pressed but nothing happens. So after waiting for about 15 minutes I do a soft reset to get back to the HTC Sense screen (today screen). I take the phone out of Airplane mode cause from reset. I hit the volumn up button and it works fine. I tap the end key and it puts me back in Airplane mode.
So I reflash stock rom back in that by the way wouldn't go until I unlocked the phone with HardSPL. Apon first reboot it still boots with phone shutting down into Airplane mode. Turn phone back on then turn power off. Take battery out. Replace battery. While holding Talk ad End buttons I tap power on for hard reset. Goes through try colored screen then to the volumn up option screen. I tap volumn up and nothing still happens.
I'm looking at Task 29 but I am worried about the volumn button not working.
Anyone have any ideas on what direction to take. Thank you
Click to expand...
Click to collapse
Which model is your device? You can find the model number above the barcode that is under your battery. It will be in the form of RHODxxx where "xxx" is a three digit number. From here, I'll be able to help you a bit better once I know which model you are using.
Thank you for the reply. The model# is M8RHOD400. Since my first post I have tried flashing other Roms and I think it was the Sharkie Rom that actually said it could find the end key file. Other than that all the other Roms I tried pretty much do the same. When end key is tapped it shut phone off. Plus the volumn up still doesn't work at the hard reset state. It works normal otherwise but when I try to hard reset it will not go past the first screen that says press vol. up to reset. Thanks again so far.
Hootyhoo said:
Thank you for the reply. The model# is M8RHOD400. Since my first post I have tried flashing other Roms and I think it was the Sharkie Rom that actually said it could find the end key file. Other than that all the other Roms I tried pretty much do the same. When end key is tapped it shut phone off. Plus the volumn up still doesn't work at the hard reset state. It works normal otherwise but when I try to hard reset it will not go past the first screen that says press vol. up to reset. Thanks again so far.
Click to expand...
Click to collapse
Ok, so the first thing we need to test for is hardware fault. To do this, you will need to perform a task29 and then flash the latest Sprint ROM. After that, try to see if you have the same problems. Please do not install anything while testing. If it works fine like this, then we will need to do some specific testing on the custom ROMs to narrow down the cause.
Things have changed a bit. Long morning. I tried flashing a few ROMs to see if any would fix it. I know a feeble attempt. Well one went bad and never got past the splash screen when it went to restart. Won't connect to ActiveSync. So I tried reflashing from SD card. and I get to
RHODIMG.nbh
OS -
Press Power button
to start update image
Press VolDn button
to cancel update image
The problem is I press power button and nothing happens. I press any buttons and nothing happens. I pulled the battery and reinstalled it and got the same again. I tried to run Task 29 but how. Won't load. Tried renaming rbh file but got the same results as above. I need a way to hard reset without buttons and its obvious that nothing working outside of windows. I'm lost.
Hootyhoo said:
Things have changed a bit. Long morning. I tried flashing a few ROMs to see if any would fix it. I know a feeble attempt. Well one went bad and never got past the splash screen when it went to restart. Won't connect to ActiveSync. So I tried reflashing from SD card. and I get to
RHODIMG.nbh
OS -
Press Power button
to start update image
Press VolDn button
to cancel update image
The problem is I press power button and nothing happens. I press any buttons and nothing happens. I pulled the battery and reinstalled it and got the same again. I tried to run Task 29 but how. Won't load. Tried renaming rbh file but got the same results as above. I need a way to hard reset without buttons and its obvious that nothing working outside of windows. I'm lost.
Click to expand...
Click to collapse
First of all, you should stop trying to update with the SD card. That's the problem you're having, so we need to try something different. Flash it via USB. You don't need an Activesync connection. It just needs to change from SERIAL to USB at the bottom of the bootloader screen. Once that happens, simply run the RUU and it will flash to your device. Do task29 first. Then do the stock Sprint ROM. Task29 cannot be flashed via SD anyway. The NBH file in task29 is a filler file. It's the actual RUU in it that is modified to perform the wipe.
So, let's try this again.
1. Get into the bootloader by holding voldown while turning the device on.
2. Plug it in to a USB port on your PC.
3. Once the text at the bottom of the screen changes from SERIAL to USB, begin running the task29 RUU.
4. Once the progress bar gets to 99% on the task29 flash, hold the voldown button again and await the restart.
5. Once it restarts into the bootloader and the text changes again, begin flashing the latest Sprint ROM.
6. Allow the ROM to boot up all the way and settle down, then give it one soft reset.
7. When it comes back again, go ahead and test it out to see if your problems persist.
8. Report back here with the results, and we'll move on from this step.
Task 29 doesnt seem to working because it reboots back to the last rom. Everything is still there. I really don't think that any of the hardware buttons work outside of working in the OS and at startup. IE volumn works when unit is on or when putting unit into bootloader mode but Volumn button does not work when trying to do a hard reset or a Task 29. Power button turns on unit, turns off unit, puts into bootloader mode, starts hardreset. I have loaded a Custom Rom just because maybe with the X button on the bottom and bigger it might be easier. I'm all ears from here on out. Its seems I need to clear ROM or Cmos without button usage. I don't know if that makes any sense to you but like I said I'm all ears on what to do now. Thanks for the little lesson on flashing without Activesync. Feeling kinda stupid about that one. Thanks for the help so far.
Hootyhoo said:
Task 29 doesnt seem to working because it reboots back to the last rom. Everything is still there. I really don't think that any of the hardware buttons work outside of working in the OS and at startup. IE volumn works when unit is on or when putting unit into bootloader mode but Volumn button does not work when trying to do a hard reset or a Task 29. Power button turns on unit, turns off unit, puts into bootloader mode, starts hardreset. I have loaded a Custom Rom just because maybe with the X button on the bottom and bigger it might be easier. I'm all ears from here on out. Its seems I need to clear ROM or Cmos without button usage. I don't know if that makes any sense to you but like I said I'm all ears on what to do now. Thanks for the little lesson on flashing without Activesync. Feeling kinda stupid about that one. Thanks for the help so far.
Click to expand...
Click to collapse
I don't know where you got your task29 utility from, but you cannot run it from SD. It HAS to be used with the RUU that came with it. It is the modified RUU that runs the task29 function. Just to eliminate the confusion, I'm uploading a modified RUU to this post that is very simple to use. Extract it from the archive and follow these instructions.
1. Connect the device (in bootloader) to your PC and wait for USB to show in the bootloader.
2. Run the RhodiumWAdvancedRUU.exe
3. Select the third radio button that says "Perform task29 only."
4. Uncheck the box that says "Restart utility when task29 completed."
5. Hit Next and keep going through it until it flashes.
6. Once the progress bar gets to 99%, hold your voldown button and wait for the reboot.
7. Once you are back into the bootloader, wait for USB to show up on the screen again and then flash the stock ROM.
8. Once the flash is complete, allow it to boot once and settle, then soft reset.
9. Once it restarts, test the problems again.
10. If the problems persist, we can move on from here.
Note: If you want to make sure that the task29 utility worked, feel free to try and boot it after performing the task29 and see how far it gets. If it gets stuck at the bootscreen, then you know it worked. Simply pull the battery, or hit the reset button, and power it back on while holding voldown to return to the bootloader and continue with step 7.
I cannot find the uploaded file that you sent, but also I am not trying to run the Task 29 file from SD card. I'm trying from the comp but like I said, when in any mode other than Windows, I really believe none of the buttons work. Volumn down at 99%. Volumn up on a hardreset. The buttons work to get me into the various mode either from Windows or at startup, but once into the special modes I think I don't get any buttons. That and the fact that the only thing the endkey button does in turn phone on and off but doesnt end anything is peculiar to a person like me. Anyways I didn't get your Task 29 file yet.
Thanks again
Hootyhoo said:
I cannot find the uploaded file that you sent, but also I am not trying to run the Task 29 file from SD card. I'm trying from the comp but like I said, when in any mode other than Windows, I really believe none of the buttons work. Volumn down at 99%. Volumn up on a hardreset. The buttons work to get me into the various mode either from Windows or at startup, but once into the special modes I think I don't get any buttons. That and the fact that the only thing the endkey button does in turn phone on and off but doesnt end anything is peculiar to a person like me. Anyways I didn't get your Task 29 file yet.
Thanks again
Click to expand...
Click to collapse
That's because I forgot to upload it. Sorry. here it is.
I know you feel that way, but there are a few things we can try. We just need to go step by step to rule things out. Please trust me on this. I'm trying to keep from saying that your phone is having hardware troubles, because I think it is fixable as it is now. We just have a certain order to attack it from.
I do appreciate the help I have always gotten from this site and thank you. The worries that I have are actually getting any buttons to work when doing any work on the phone outside of the windows format. I noticed that at 99% I am to tap the vol. dw button and I don't think thats gonna work. From my desktop computer exsperience that I have I know there is actually 3 modes happening that work in conjunction with one another. CMOS MSDOS and Windows. I don't think its a windows issure and I don't know what else there is in these phones that work, but I will try this program and thank you again. I will let you know where I at with it in a few.
Hootyhoo said:
I do appreciate the help I have always gotten from this site and thank you. The worries that I have are actually getting any buttons to work when doing any work on the phone outside of the windows format. I noticed that at 99% I am to tap the vol. dw button and I don't think thats gonna work. From my desktop computer exsperience that I have I know there is actually 3 modes happening that work in conjunction with one another. CMOS MSDOS and Windows. I don't think its a windows issure and I don't know what else there is in these phones that work, but I will try this program and thank you again. I will let you know where I at with it in a few.
Click to expand...
Click to collapse
Even if holding voldown doesn't work, you will still be able to boot back into the bootloader. task29 will clear the internal memory of everything. There won't be anything to load, so it will hang on the splash screen if it tries to load. Don't worry. We're going to try everything we can before we call it quits. This is a unique problem, but I think it can be fixed. Like I said, we just have to go in order.
Okay. First of all I'm sorry for the void between your last message and now. Its been a wild week so far. Thanks again for the help so far. With that said and done heres were I am at. I tried your Task 29 software and it did seem to be different at visualy. Possible problem is, is that when it rebooted after following your instructions, it did not go to the tri colored screen but to a blueish looking screen with the words Touch Pro 2 across the center. It almost looked like a splash screen, but never went any farther. So I'm not sure if that was acceptable or not as a proper task 29 but I did go ahead and load the stock rom into it and it went find. After the first reboot it started up with Airplane mode on. I shut it off and turned on the phone again. Everything was okay. You can only assign the phone button and nothing else that I know of so I couldn't see what was assigned to the end key so I pushed it. immediately it stuck the phone back into airplane mode again. Push or I should say tap and it took it out of it. I realize that by default the phone set the long press end key to shut the airplane mode on and off, but I am tapping and only tapping as I always have in the pass. Well so I got the idea of trying a different Rom in hopes that something will program the key to not shut the phone function off everytime I accidently tap the end key, I tried a few and Sharkies seems to surfice for the moment. By tapping the end key only brings up the Comm Manager instead of shutting the phone function down. Funny thing is though is that also was Sharkies default for long press. The problem has become with that now is that it has been just popping up by itself over and over. So I started tapping the end key when it popped up and suddenly it seems that it worked until I realized the the end key doesnt seem to be working at all. It clicks but thats it. So what to do now. Good thing at this time is the fact that I dont have to worry anymore about accidentally tapping the end key.Good chance it could be the button it self. I don't know. What ya think?
Hootyhoo said:
Okay. First of all I'm sorry for the void between your last message and now. Its been a wild week so far. Thanks again for the help so far. With that said and done heres were I am at. I tried your Task 29 software and it did seem to be different at visualy. Possible problem is, is that when it rebooted after following your instructions, it did not go to the tri colored screen but to a blueish looking screen with the words Touch Pro 2 across the center. It almost looked like a splash screen, but never went any farther. So I'm not sure if that was acceptable or not as a proper task 29 but I did go ahead and load the stock rom into it and it went find. After the first reboot it started up with Airplane mode on. I shut it off and turned on the phone again. Everything was okay. You can only assign the phone button and nothing else that I know of so I couldn't see what was assigned to the end key so I pushed it. immediately it stuck the phone back into airplane mode again. Push or I should say tap and it took it out of it. I realize that by default the phone set the long press end key to shut the airplane mode on and off, but I am tapping and only tapping as I always have in the pass. Well so I got the idea of trying a different Rom in hopes that something will program the key to not shut the phone function off everytime I accidently tap the end key, I tried a few and Sharkies seems to surfice for the moment. By tapping the end key only brings up the Comm Manager instead of shutting the phone function down. Funny thing is though is that also was Sharkies default for long press. The problem has become with that now is that it has been just popping up by itself over and over. So I started tapping the end key when it popped up and suddenly it seems that it worked until I realized the the end key doesnt seem to be working at all. It clicks but thats it. So what to do now. Good thing at this time is the fact that I dont have to worry anymore about accidentally tapping the end key.Good chance it could be the button it self. I don't know. What ya think?
Click to expand...
Click to collapse
On task29, it removes the entire ROM from the device's internal memory. There was nothing to boot up, so it stopped at the splash screen. That's how task29 works.
Well, this allows us to completely remove the possibility of the software's effect on your problem. What is happening is that the device is recognizing a short press as a long press. Since the button commands are interpreted by the SPL, we've got one last thing to try before declaring hardware fault. We'll need to flash the stock SPL, again to see if that clears it up. To do this, I'd ask that you flash the latest stock ROM to your device. After this, you'll need to go back to the CDMA Hard SPL thread and grab the latest stock SPL. Flash that to your device. Then boot it up and see if the problems persist. If it continues to register short presses as long one, then you have a hardware fault. If this fixes it, then you should be able to flash Hard SPL again and load another ROM with no problem.
Accidental post