Related
Hi Guys,
Whenever I remove the battery from my XDA 2S I lose everything and have to set up the OS from scratch.
I have spoken to O2 and they have told me this is normal? But how can this be? It is the most stupid thing I have ever heard.
Please if someone could just tell me if their XDA 2S does this I would be more than grateful!
Thanks in advance.
Jonnycash!
Go to settings/ Power icon and check the status of both the Main Battery and the backup Battery, the first could be at any charge % the backup Battery should be at 100%, this is used to hold the data on the phone for a short duration, sim card swap or battery swap with the machine selected OFF first. If its loosing data then there is something wrong with it, I can remove the Battery on my IIs for 10 mins if need be without a problem - Mike
Yes the Backup Battery is at 100%
It loses everything as soon as I take the battery out, I can put the battery straight back on, start the phone and OS setup begins.
When you say selected "off". Do you mean quickly pushing the power button once.
I have done this and still it loses everything.
Looking forward to your response.
Jonnycash!
All I can sugest are two options
1, Return the phone as it is clearly faulty, demand O2 repair the unit or try for an Exec as a replacement as re-compense, you might get this easily as they are no longer offering the IIs.
2, install something like Sprite back-up and configure the back-up to re-install everthing hardly ideal, and this is not what I would do.
Mike
Yes, I have just got it back from being "repaired". they said that they replaced the circuit board but it still does it.
I will send it back as suggested and try get a new one.
Thanks
Jonnycash
After taking out the battery, try not to push the tab(the one you pull back and the battery pops up) that holds the battery back into place until you re-insert the battery.
Jonnycash said:
Yes, I have just got it back from being "repaired". they said that they replaced the circuit board but it still does it.
I will send it back as suggested and try get a new one.
Thanks
Jonnycash
Click to expand...
Click to collapse
Sounds like a duff backup battery to me ( see pic), changing the mainboard would seem a sledgehammer to crack a nut. I have had this with blueangels after re-assembly, even with the backupstatus at 100%. I leave on a cradle charging overnight then do a hard reset - seems to work for me.
Richard
i have that problem as well before. but maybe this will help you a bit.
because i always do it removing the battery when changing my sim card. how i wish they would put the sim card away from the battery. ( calling the attention of the engineers for future references).
i started on the permanent save check mostly on contacts and appointments (I needed them all the time) (start>settings>system>permanent save). then i usually turn on the flight mode then turn off the pda from the power button.
thats the time i take the battery off and either to swap the sim card of the battery. then it automatically go to soft reset when the battery is back you will notice that after the automatic soft reset, there will be a small window showing appointments and contacts restoring.
i hope this will help.
I've had this, once. I've heard that this is a bug of that little black thingey that holds the battery, because it supposed to switch between backup battery and normal battery. Too bad sometimes it does not do this at all...
finally this happened to me to today. I by mistake took the battery out and when I put it there again, it hard resetted itself. Many of my notes were stored in main memory, which I had taken from my teacher just 30 mins ago
kamal
kdskamal said:
finally this happened to me to today. I by mistake took the battery out and when I put it there again, it hard resetted itself. Many of my notes were stored in main memory, which I had taken from my teacher just 30 mins ago
kamal
Click to expand...
Click to collapse
It happened to me again few days ago, under 2003SE (I had to downgrade for something). One thing i love in WM5 that I don't have to worry about this.
It has happened to me many times as well as I am always changing batteries. As somone mentioned above it seems to be a bug with the battery holder (the little black tab you clisk to hold the battery in.) I just keep my contacts backed up each time I add a new one. as for the applications they can usually waite till I restore them.
need solution..
need a good and working solution for this...........
Re: need solution..
isk2005 said:
need a good and working solution for this...........
Click to expand...
Click to collapse
Eeerrrr. how about ' replace the battery' - they are standard cells...
Richard
Mabey its not clear what seems to be happening here
When you drop the unit and /or when you open the little black clip that holds the battery in place. Somtimes the phone looses all stored information and goes to hard reset. There seems to be 2 bugs in action here.
1) The batterys seem to get into a strange state where they dont work properly. (I have found that putting the battery into the rear slot of the charger reconditions it to fix this problem.)
2) Some units seem to have a bug with the battery latch when you open the latch accidently or somtimes even just when changing the battery intentionaly it seems not to switch to back up battery corectly. My theory is that there is a dead zone in the latch that does not make the correct transfer if it isn't fully engaged in either direction. It is a really poorly devised way to handle battery changes but hey its too late for them to redesign it. I can not say how many ppl have this issue or if it is everyone or just some people but I do know this is the case on mines and many of the forums I've read.
Solutions:
1) Back up your unit whenever you add data to it. you can just do a contact list back up which only takes 1 min for me and my sx66 has over 2k contacts. Do full back up once a week that should cover your apps and data.
2) Keep your battery reconditioned at least once a week use the rear charging slot for the battery. If you only have one battery this is not an option so I suggeest if you are going to keep your sx66 for any length of time buy a spare battery.
3) Recently I have begun using a small peice of duck tape to secure my battery latch. It is a pain in the rear but I have droped my unit once in this configuration and the battery and latch stayed in place.
Additionaly:
To make restores easier you can include some of your favorite applications in your ext roms. Just snoop around in the forums and you will see directions for manipulating ext rom.
Also look into changing the directorys where you store information. IE your mem card and the onboard storage directory seem to never get nuked unless it is done by the user.
Anything short of the above listed or replacing the hardware is not viable, because these are HARDWARE bugs. Version 5 avoids this issue because it does not hard reset your data like all previous versions of ppc. However the hard ware issue is still there it just doesnt effect you. But if you upgrade your rom be carefull because you are trading the bugs you know for the ones you don't know...lol
thanks for advice ........
dont worry richard am shifting to o2 exec
isk
I can’t power up my device. I burned ROM with “htc hermes Customized V1” by faria about 1 week ago and it worked just fine since. Today it just went dead – no reaction to power or reset buttons, the screen stays black. When I connected the power supply to it, the red LED went on for 5 sec and then screen went on as well (very bright white, no text or anything on it) and it stayed on even when I disconnected a power plug. The only way to turn the screen off was removing the battery.
If anyone has an idea what is going on please let me know. The phone is just three weeks old. Will I have a problem to replace it under warranty?
Thanks.
Will it go into bootloader mode?
No, it will not.
here is the thread you need. First give it a read, and then post the requested information in the requested format and the experts will be more than willing to help. http://forum.xda-developers.com/showthread.php?t=286755
I’ve looked at this thread for a minute and it looks to me that my case is different. These postings are dedicated to cases when devices went dead during unsuccessful burning of ROM. My device was working perfectly well after I burned the ROM for at least a week. I could be wrong, but I think that I have a hardware failure. Nevertheless, thank you very much for your advice – I am going to read this post tomorrow and will try to follow the steps of procedure.
Regards
Going out on a limb here, but are you using the charger that came with the unit, or a different (i.e. 3rd party, Motorola, etc) charger? My Wizard (RIP) displayed the exact same behavior if the battery dropped below a certain level and I tried to charge it with my car charger. Only the charger that came with it would give it enough juice to boot.
i had the same problem a few month ago. I sent it to the support and got a new device.
regards
But, have you had any problems with warranty when exchanged the device? I understand that ROM modification can negate warranty.
Thanks
Yes, most of what we do to our phones here voids the warranty. It really just depends on how close they check when you send/take it in. Some folks have managed to exchange phones that they broke, others have not. I've read somewhere in here that someone got an exchange phone right away, and then sometime later, when the repair center saw that they had been flashing the phone, they billed the person for the cost of the replacement.
Others can maybe suggest ways to try to cheat the system, I just accept the fact that if I break my phone I have to buy a new one. I knowingly and intentionally voided my warranty so from that point on the vendor is not responsible.
Hi all
I have a problem with my blue angel - when i disconnect the main battery (even for 1 second) it hard resets. It's strange because in the settings->Power the backup battery shows as fully charged.
So what should i do? Is it a faulty backup battery or what? And if it is how can I replace it?
Thanks for your answers!
I'm having exactly the same problem and getting sick of my blue angel, i use it for my sat nav and it's annoying to lose all s/w and settings
can anyone help??
hjafary said:
can anyone help??
Click to expand...
Click to collapse
I have exactly that problem and i am gonna slowly have to take care about it... Will write it down here if i succeed. Probably it wont go without opening the device and soldering...
well, upgrading to windows mobile 6 resolved this problem
but not for a long time
http://forum.xda-developers.com/showthread.php?t=437362
Two options
1. Upgrare to w5 or w6 to advoid data lost when battery got trouble.
2. Use backup, such as spb back up and shceduled (everyday) backup, then you never lost your data and sw
Yes it is possible to replace backup battery as I had to change mine from my old broken xda iis < it was a little tricky job to remove the cap which holds the battery in its place securely, once you release the cap change the battery ( make sure you insert the new battery with correct polarity) and re insert the cap .
Takes 10 minutes thats only if you can release the cap without damaging any bits on the board. Just take your time dureing this process.
koalauk said:
Yes it is possible to replace backup battery as I had to change mine from my old broken xda iis < it was a little tricky job to remove the cap which holds the battery in its place securely, once you release the cap change the battery ( make sure you insert the new battery with correct polarity) and re insert the cap .
Takes 10 minutes thats only if you can release the cap without damaging any bits on the board. Just take your time during this process.
Click to expand...
Click to collapse
You forgot to mention.... Make sure to replace with proper "Rechargeable" Battery.
Where is the backup battery located on an SX66 BA? Where can one get one without spending a lot?
Thanks in advance.
Backup Battery
OK. I finally found some pictures of the HTC Blue Angel completely disassembled. Go here:
http://www.land-of-kain.de/ppc/mda3/disassembly/
It shows something that looks like a battery with a piece of silver tape. I assume this is the backup battery.
I am running a fantastic version of WM6.1 that is extremely stable and fast.
I've increased the memory available to 60MB (see the BA Wiki's upgrading to WM5 instructions). While WM6.1 does store your contacts and other info in non-volatile memory (i.e., it won't be erased if you battery goes dead), there are some passwords for internet settings, etc. that are not saved. So if my battery falls off (mine always does), I often have to add the password to connect to my carrier and I have to re-enter my password for the my push email. I believe I would not have to enter either if the backup battery was working. So I'm trying to figure out how to do it.
I found some of the backup batteries for $5.00 but one has to make a $35 minimum purchase. I'm still probably going to do it.
you can buy them from most shops - just make sure you buy the right type -
it would be this: http://www.onlybatteries.com/webimages/images/15293.jpg
or this : http://img.en.china.cn/0/0,0,394,2136,340,374,11fad816.jpg
The top one is CR2032
and the bottom one is CR2032
Wiki:http://en.wikipedia.org/wiki/Button_cell
good luck, hope you get it working
Josh.
The Batter in the Blue Angel is a LR55 / AG8
beakybal4 said:
you can buy them from most shops - just make sure you buy the right type -
it would be this: http://www.onlybatteries.com/webimages/images/15293.jpg
or this : http://img.en.china.cn/0/0,0,394,2136,340,374,11fad816.jpg
The top one is CR2032
and the bottom one is CR2032
Josh.
Click to expand...
Click to collapse
I've opened my i-Mate PDA2K and the battery turns out to be an LR55 (aka AG8), judging by the dimensions (11x2mm).
The trickiest part about getting access to the battery was the battery cap. It twists in place but that doesn't do anything. I had to pry it open using a small knife as a lever against the component to the right of the, but that seems to have unglued the whole battery+cap ensemble from the PCB. I have no idea if the device will still work after I replace the battery.
dandv said:
I've opened my i-Mate PDA2K and the battery turns out to be an LR55 (aka AG8), judging by the dimensions (11x2mm).
The trickiest part about getting access to the battery was the battery cap. It twists in place but that doesn't do anything. I had to pry it open using a small knife as a lever against the component to the right of the, but that seems to have unglued the whole battery+cap ensemble from the PCB. I have no idea if the device will still work after I replace the battery.
Click to expand...
Click to collapse
Looking at your photos it seems you have took aout all the pieces.
If you see this http://forum.xda-developers.com/showthread.php?t=501989&page=11 you'll realize there are two pieces: the cap with three labels and the "small saucepan" where the batt properly is. And that should remain attached (soldered) at the mainboard. So, perhaps you have unsoldered something you shouldn't.
And the battery is the V18HRT, also known as V20HR ("V" because is Varta company). I bought one through ebay.
Good luck
Sigh. This is also my problem as my old Xda2s and HP iPaq both require internal battery replacement - Varta V18HRT. Is there a substitute for this considering its quite hard to find this Varta battery? And if one knows, where does one find this Varta battery in Manila.
Use a Varta V20HR to replace V18HR backup battery
saddam said:
Sigh. This is also my problem as my old Xda2s and HP iPaq both require internal battery replacement - Varta V18HRT. Is there a substitute for this considering its quite hard to find this Varta battery? And if one knows, where does one find this Varta battery in Manila.
Click to expand...
Click to collapse
I know this is an OLD thread, but I thought I would post regardless.
There is a suitable and AVAILABLE Varta NiMH button cell for our HTC Blue Angel smartphones. The Varta V20HR is a slightly higher capacity battery (20ma vs 18ma), same diameter and only super slightly thinner (2.25mm vs 2.3mm). The small difference in height should NOT make a difference as the backup battery cell holder is a spring tension design. I have order a couple of these (under $5 each) and will be undertaking the replacement once my order arrives.
Wow
I have found out that looks like the MBU20 also replaces the V20HR so it can be another option. I am going to try that one as I am in Europe and it seems all the V20HR available are in the US. It has a Nominal capacity of 20 mAh.
Here is a link for the MBU20 saying it replaces the V20HR: http://www.master-instruments.com.au/products/59150/MBU20.html
It has same measurements as the original V18HRT as you can see in the datasheet from Varta: http://www.varta-microbattery.com/applications/mb_data/documents/data_sheets/DS55802.pdf
And those MBU20 are quite cheap in Europe. I will post here an update. I still have my original Blue Angel going strong and 5 more as backups that I am working on making them nice again. I am glad I took them out of the drawer
Phone just quit charging the other day. No water damage or anything, it just died. Holding the power down trying to boot it after letting it charge for a while doesn't do anything. The phone is cold to the touch and I think it just went kaput.
No biggie, right? I have a warranty.
The problem is when I try to email or call them, I get nowhere. There is no response to any communication with LeEco. Does anyone have any ability to initiate a warranty claim and an RMA? I just need a replacement and am not looking for a refund or anything. I'm in the US.
Please help - I feel like I just lost $200 if I can't reach anyone over at LeEco.
Purchased the phone at Best Buy and in calling them they gave me a number that doesn't exist for support at LeEco.
Do I have any recourse with Best Buy?
Thanks in advance.
I am in the same boat, was trying to call them multiple times, but no response. Send them email also.
I dont know if you guys live in a humid climate or not but for the hell of it , put it in bag of rice seal good and let it sit for 24 hours can't hurt. Maybe moisture got in there
Have you try this: https://forum.xda-developers.com/le-max-2/how-to/guide-hard-brick-fix-qualcomm-hs-usb-t3492949
Good luck
Maybe you could submit a ticket to Leeco, from here: http://www.leeco.com/us/user/cutTicket.html
bwzippy said:
Phone just quit charging the other day. No water damage or anything, it just died. Holding the power down trying to boot it after letting it charge for a while doesn't do anything. The phone is cold to the touch and I think it just went kaput.
No biggie, right? I have a warranty.
The problem is when I try to email or call them, I get nowhere. There is no response to any communication with LeEco. Does anyone have any ability to initiate a warranty claim and an RMA? I just need a replacement and am not looking for a refund or anything. I'm in the US.
Please help - I feel like I just lost $200 if I can't reach anyone over at LeEco.
Purchased the phone at Best Buy and in calling them they gave me a number that doesn't exist for support at LeEco.
Do I have any recourse with Best Buy?
Thanks in advance.
Click to expand...
Click to collapse
Phones don't die just like that, in your case, it's either the battery, or a hard brick, or a defective screen. You should better change the battery and try to flash stock software afterwards if battery doesn't work, then you go for the screen, also the chargers that LeEco provides are crappy so it maybe went "out" and afterwards you went out of battery, try to charge with a different cable and charger. Can't post links till i get to 10 posts, if you don't mind and if i was helpful click the thanks button .
Well the phone is in with some rice and a silicone packet thing that absorbs moisture. It never got wet before it died, but figured what the heck, I have no other options.
LeEco won't pick up the phone, nor return my emails or voicemails. Nice company!
@filippos96 - phone is fully stock and I've tried several different chargers. The phone doesn't get warm at all - like its not even receiving power. If I open it up to replace the battery that might not fix it if the issue is with a component before the battery.
Thanks for the suggestions guys. If anyone knows a shortcut to open an RMA I would greatly appreciate it.
bwzippy said:
Well the phone is in with some rice and a silicone packet thing that absorbs moisture. It never got wet before it died, but figured what the heck, I have no other options.
LeEco won't pick up the phone, nor return my emails or voicemails. Nice company!
@filippos96 - phone is fully stock and I've tried several different chargers. The phone doesn't get warm at all - like its not even receiving power. If I open it up to replace the battery that might not fix it if the issue is with a component before the battery.
Thanks for the suggestions guys. If anyone knows a shortcut to open an RMA I would greatly appreciate it.
Click to expand...
Click to collapse
It doesn't respond to ANYTHING? Like if you press the power button for 10+ seconds does it vibrate? Like it doesn't even show boot screen or smth? Need more info for a better diagnosis. Also, doesn't matter if the phone is fully stock, anything could have been a factor leading to hard brick, which is most likely your case.. It's like most certainly the battery or a hard brick, may be a bad screen, one of those 3 for sure though. I vote for hard brick and dead battery . Happened to me on my 1+1.. I had no hope that the phone was ever gonna be usable, though that the cost would be higher than the ceiling, it turns out that it was just 8$, a new battery.. I have much much experience with smartphones, used to run my own repair and sell shop. It's up to you if you wanna follow my advise for free, or visit a fellow repairman . If this was any helpful to you please make sure you click the thanks button so i can get better and more helpful .
No screen on at all. No charge light. Imagine a brick. This is similar.
Did you purchase your phone with a credit card? Most have extended warranty programs. I'd go that route and see if you can get your money back. They generally don't kick in until the manufacturer warranty expires but it looks like the manufacturer is out to lunch. Doesn't hurt to try.
Hi well my charger burned in the Le Eco Le Pro 3 while charging and now the phone wouldn't charge. Mind you it's and excellent phone and while my warranty comes to an end in October I can't get in contact with the manufacturer. It's really annoying because I only want that part fixed.
Has anyone managed to get in contact with them please help.
Lesy_les said:
Hi well my charger burned in the Le Eco Le Pro 3 while charging and now the phone wouldn't charge. Mind you it's and excellent phone and while my warranty comes to an end in October I can't get in contact with the manufacturer. It's really annoying because I only want that part fixed.
Has anyone managed to get in contact with them please help.
Click to expand...
Click to collapse
LeEco did a bit of downsizing. Read the history section.
https://en.m.wikipedia.org/wiki/LeEco
Legally, Best Buy should honor the warranty and most suppliers would.
For example, Just a month ago, I have returned one of my LeEco phones (5 months old) that was damaged by a faulty cable. and I received a brand phone under warranty.
Unfortunately, Best Buy is notorious for not honoring factory warranties or even their own Geek Squad extended warranties.
https://topclassactions.com/lawsuit...fails-honor-geek-squad-plans-full-warranties/
You bought a phone with a published warranty from a company that is still in business. Most likely Best Buy received extra margin to service the warranty themselves.
Squeaky Wheel gets the grease
Since you cannot reach the manufacturer , you should keep contacting Best Buy, stay on the line and do not take no for an answer, keep asking for the next person up and record the phone call ( they are recording you) if you keep pressing they may give in. Important, remain polite and professional. If you are rude, they will do nothing for you.
Persistence works -read the solution on this page:
http://forums.bestbuy.com/t5/Best-B...pany-s-Promise-of-Quality-Service/m-p/1116017
Alternatively, get another cable and try unbricking your phone by following the unbrick guide. ( its works but only if you have a x727 or a x720) Its also possible that you have a hardware issue like I did. Worst case you can buy parts for these phones on Ebay and Alibaba
Sorry to hear about your phone
Which charger were you using?
Hi, I purchased 2 LeEco Le Pro 3 phones, and both have broken down completely manufacturer's fault. One, the battery inside the phone started to expand and push out the front screen glass out of its edges. The other one, which I purchased as a backup, the screen auto rotate does not work. I think the sensor is broken.
Now, I have no way to contact the manufacturer for the warranty repairs, none of the contact info are working. I purchased the phones directly from the manufacturer LeEco Mall (just as OnePlus sells directly to the consumer), so I can't even try to return it to the distributor or the seller.
PS: how long is the warranty period on these phones?
PPS: is there a reason that many distributors are still selling the Le S3, and other models except for the Le Eco Le Pro 3? I can't even buy the Le Pro 3 any more. Anyone else having the same problems mentioned above?
Guys give up, we are ALOT of LeEco Le Pro 3 users who got this problem. Everything started from nothing
@tsongming did you heard any news? I can see that one more user killed his phone Are there more or just him ? This is too strange, since 1 month alot of phones died .... hmm
---------- Post added at 05:52 PM ---------- Previous post was at 05:34 PM ----------
bwzippy said:
No screen on at all. No charge light. Imagine a brick. This is similar.
Click to expand...
Click to collapse
we have exactly the same, try to search our thread on it. One user fixed his phone by "re-powering" his battery. I bought another battery and nothing happend for my phone sadly.
Stock
Unfortunately, all of these recent issues are likely due to manufacturing. If you take a look you will find that quite a few people who never used a custom rom are also having these issues on stock. Probably alot of the issues are the battery. Ideally the battery should not go over 100F / 38C
For these cases a battery will likely resolve the issue, of course there is also the issue with burned ports.
Custom Roms
But many of the Roms made within the last couple of months are based on Pie and there are too many unknown factors, such as permissions being reset for unknown reasons, edited thermal settings reverting to default etc.
Recently we have seen chip damage. But the cause of chip damage has been found and resolved.
If you are reading this post and your phone is fine. Take every precaution to ensure that your battery stays cool and if on Pie make sure that you have the very latest thermal patch installed.
Since the battery situation has reached a point of no return (under 1.5 hours of SOT, random restarts and bootloops under 50%) and since I won't have the opportunity to get a new device for the next year, I would really appreciate it if someone could share his/her experience with battery replacement via the official HTC service.
I can send my device to either UK or DE service points, so any specific experience with those would be ideal. Furthermore, I would really love to know if someone had any issues with sending their devices with an unlocked bootloader, or received them damaged or scratched, as this is the reason why I am still reluctant of sending my device (I have read some horror stories of devices returning scratched or with damaged screens).
Any help would be highly appreciated.
billgs said:
Since the battery situation has reached a point of no return (under 1.5 hours of SOT, random restarts and bootloops under 50%) and since I won't have the opportunity to get a new device for the next year, I would really appreciate it if someone could share his/her experience with battery replacement via the official HTC service.
I can send my device to either UK or DE service points, so any specific experience with those would be ideal. Furthermore, I would really love to know if someone had any issues with sending their devices with an unlocked bootloader, or received them damaged or scratched, as this is the reason why I am still reluctant of sending my device (I have read some horror stories of devices returning scratched or with damaged screens).
Any help would be highly appreciated.
Click to expand...
Click to collapse
+1
I would much appreciate the same info except that I'm in the US. Same exact battery difficulties. I've already bought a new device but I would love to keep this one operational as a backup if the battery can be replaced without ruining the device. All the DIY videos I've watched look like a nightmare.
Not in EU/US, so my experience might be different from yours (YMMV disclaimer)
Got my 10 in for battery replacement (last week of warranty left), and just got it back.
Don't try to replace the battery yourself, to be honest.
I send my phone in for only a battery exchange, and it came back with a new battery, and a new screen.
It's very likely to damage the ribbon cable while putting the phone back.
What I see from some other forums is, basically if you've had software mod, they won't warrant mainboard damage.
Haven't heard anyone had a damaged phone back from official repair though.
It costs around $40-50 for a battery exchange out of warranty IIRC.
jerry855202 said:
Not in EU/US, so my experience might be different from yours (YMMV disclaimer)
Got my 10 in for battery replacement (last week of warranty left), and just got it back.
Don't try to replace the battery yourself, to be honest.
I send my phone in for only a battery exchange, and it came back with a new battery, and a new screen.
It's very likely to damage the ribbon cable while putting the phone back.
What I see from some other forums is, basically if you've had software mod, they won't warrant mainboard damage.
Haven't heard anyone had a damaged phone back from official repair though.
It costs around $40-50 for a battery exchange out of warranty IIRC.
Click to expand...
Click to collapse
Who did the battery replacement? In the US HTC won't replace the battery anymore. I contacted them last week and was told they no longer do it. I'm looking into third party solutions now.
bacon612 said:
Who did the battery replacement? In the US HTC won't replace the battery anymore. I contacted them last week and was told they no longer do it. I'm looking into third party solutions now.
Click to expand...
Click to collapse
Official HTC repairment center in Taiwan. However in my case my phone is still barely in warranty (a week or less). They covered all cost within warranty. Heard an out of warranty battery exchange is around $40-50.
Also, it seems that they also repair foreign htc phones, although at a additional cost of $35, plus whatever the replacement part costs.
If you're really desperate about your battery and don't want to risk it, maybe pay extra? Just sayin' , and not endorsing anything.
Maybe there's some 3rd party that will exchange 10's battery? Just make sure that they'll also change the screen if they damaged it.
Hey folks,
I live in Europe (France). I bought an OEM battery at a fair price from Ebay (I can find the link if anyone is interested) and had the repair done by a store nearby for ~40 euros (which is not so much considering the time it took them to remove the screen without any damage !).
Since the guys agreed to make the change for the same price, I also took the opportunity to replace the rear case, to a beautiful brand new red housing. Now my 10 seems like it just came out of the box, for less than 100 euros in total. I'm happy !
Exact same battery issues over here, but located in AUS. 3rd party repairer is having major issues locating a battery, so I'm going to try going through HTC. Wish me luck!
I just did replacement by myself with the battery that i bought from aliexpress.so far is the winner when i compare with My brother s 2 Yo Phone.i did HTCbattery test. Mine ended with 92% and his 80%
It's a very hard device to repair honestly. I sent my phone for a battery replacement and they accidentally messed up part of the screen(Im guessing they bent a part in the ribbon cable for the screen). I recommend you send it to HTC themselves or a very experienced shop with good reputation and don't try to do it yourself. I must say it does make a huge difference to have the battery replaced.
When i sent my phone in, it was completely stock afaik (it was unlocked and with a custom rom before); howerever, they installed a different version and relocked the bootloader as stated in the papers you sign. It just came back like it was out of the box except that the bootloader said *Tampered* and *RELOCKED* so they didnt restore the bootloader status.
I've got my HTC U12+ two days ago and when I got my 10 out of the case to swap sim cards I noticed a small bulge on the display (see photo). I guess my battery is a bit bulged or something, so I'd like to get it replaced. How should I go about it? I've already written the HTC support, since there doesn't seem to be a repair address or anything like that on the homepage. I am from Germany, so I could just return the phone to my provider, but they take 2-3 weeks longer to get it repaired...
Had battery issues with my HTC 10, it didn't last much, drained quickly and had random shutdowns above 30%.
Orderer a new battery from aliexpress, carefully removed the screen and replaced the battery.
It made a real difference!
lmcmil said:
Had battery issues with my HTC 10, it didn't last much, drained quickly and had random shutdowns above 30%.
Orderer a new battery from aliexpress, carefully removed the screen and replaced the battery.
It made a real difference!
Click to expand...
Click to collapse
which battery did you ordered? 3000 mah, 4000 mah or 4300 mah?
Bareq said:
which battery did you ordered? 3000 mah, 4000 mah or 4300 mah?
Click to expand...
Click to collapse
4000 mah : https://www.aliexpress.com/item/B2P...866.html?spm=2114.13010708.0.0.3a994c4dXZXcbJ
After changing it i used battery calibrator and showed mv max of 4400
lmcmil said:
Had battery issues with my HTC 10, it didn't last much, drained quickly and had random shutdowns above 30%.
Orderer a new battery from aliexpress, carefully removed the screen and replaced the battery.
It made a real difference!
Click to expand...
Click to collapse
Hi, I have the same issue with the battery. You say you removed the screen and replaced the battery. Do you have any tutorial or step-by-step description for this?
Thanks
---------- Post added at 05:42 PM ---------- Previous post was at 05:36 PM ----------
lmcmil said:
Had battery issues with my HTC 10, it didn't last much, drained quickly and had random shutdowns above 30%.
Orderer a new battery from aliexpress, carefully removed the screen and replaced the battery.
It made a real difference!
Click to expand...
Click to collapse
Hi, I have the same issue with the battery. You say you removed the screen and replaced the battery. Do you have any tutorial or step-by-step description for this?
Thanks
SiriusCybernetik said:
Hi, I have the same issue with the battery. You say you removed the screen and replaced the battery. Do you have any tutorial or step-by-step description for this?
Thanks
---------- Post added at 05:42 PM ---------- Previous post was at 05:36 PM ----------
Hi, I have the same issue with the battery. You say you removed the screen and replaced the battery. Do you have any tutorial or step-by-step description for this?
Thanks
Click to expand...
Click to collapse
You could find tutorials on youtube, it's easy to replace, just do it step by step be pacient and careful
Shark5060 said:
I've got my HTC U12+ two days ago and when I got my 10 out of the case to swap sim cards I noticed a small bulge on the display (see photo). I guess my battery is a bit bulged or something, so I'd like to get it replaced. How should I go about it? I've already written the HTC support, since there doesn't seem to be a repair address or anything like that on the homepage. I am from Germany, so I could just return the phone to my provider, but they take 2-3 weeks longer to get it repaired...
Click to expand...
Click to collapse
To give a conclusion to this:
- I wrote the support and got a return label for a local repair shop (3rd party, but authorized by HTC)
- After I sent the device off, I got NO email confirmation that the device arrived, got repaired or got sent back
- Since Hermes is a piece of **** where I live, they never bothered to try to deliver the package.
- By pure luck I was at the Hermes packet pickup store for a different package from Amazon when I learned that I hat not only one, but two packages waiting for me.
- I assume total repair and delivery time was less than a week, but I have no idea how long the package was at the pickup store.
- The battery was replaced, but the glue around the screen was applied quite poorly, but since the device works again I don't really care.
- They didn't touch the OS. Bootloader was unlocked and a custom ROM was installed - no changes after the repair.
BSHD666 said:
You could find tutorials on youtube, it's easy to replace, just do it step by step be pacient and careful
Click to expand...
Click to collapse
I watched a few of those tutorials. Just nope. I'm a bit clumsy by nature, and precision works like that are just a no-no for me. I'd end up having to replace nearly everything, because of accidentally damaged electronic parts.
My HTC 10 is about 1 year old, bought it brand new from aliexpress, so no warranty. Well ... They claim that they give 2 years warranty, but the hurdles that I'd have to go through to send it to them (took 2 months to arrive to me), with no guarantee that I'd get the same phone back when/if they repair it ... Let's just say that it has no warranty.
Luckily, it still has no major issues, apart from an echo problem. Whenever I call someone or someone calls me, whoever is on the other side hears a feedback of his/her own voice for about 30 seconds, then the echo disappears. I hear no echoes, only whoever is on the other side hears it, and only during the first 30 seconds or so of the call. There are no echoes/feedbacks if I turn on the loud speaker or use the earphones. I've been researching about this strange echo issue, and found no solutions. But I digress.
Long story short: I'm too clumsy to attempt a disassembly myself.
Also, it seems that the HTC support here is linked to a company called Regenersis, which I've read very bad reviews about. Since my phone has no warranty, I could search for a third party shop and supply them with the new parts. Although, if it becomes too much of a hassle or if they ask for too much money, I could always buy a new phone.
SiriusCybernetik said:
Hi, I have the same issue with the battery. You say you removed the screen and replaced the battery. Do you have any tutorial or step-by-step description for this?
Thanks
Click to expand...
Click to collapse
Sorry for the late reply, i used the tutorial in : https://www.youtube.com/watch?v=CmL0mMmNBUM&t=566s&list=PLqrAW732T3e_8qLGBDX8YoCI2XWTDCQKW&index=2
Bare in mind that you have great chances of damaging your LCD during the operation, so do it at your own risk and responsability
lmcmil said:
Sorry for the late reply, i used the tutorial in :
&t=566s&list=PLqrAW732T3e_8qLGBDX8YoCI2XWTDCQKW&index=2
Bare in mind that you have great chances of damaging your LCD during the operation, so do it at your own risk and responsability
Click to expand...
Click to collapse
Thanks, this will be helpful.
lmcmil said:
Sorry for the late reply, i used the tutorial in :
&t=566s&list=PLqrAW732T3e_8qLGBDX8YoCI2XWTDCQKW&index=2
Bare in mind that you have great chances of damaging your LCD during the operation, so do it at your own risk and responsability
Click to expand...
Click to collapse
Just one more question. I've watched this and several other videos repeatedly but there's one thing that's not clear to me. Did you have to use some kind of glue or adhesive tape when reassembling the screen?
In some videos they don't mention it and in another one they uses industrial mp glue (B7000?). I have read a lot about people using tape.
What worked well for you? Are there any pitfalls?
Thanks in advance.
Sirius