Hi,
I would like to know if is there a way to perm on my BT LED without leaving my BT on. Some reg hack ?
Related
I used a program named "ozBT" to turn on/off BT from using, this program is really great, but i had a problem: when the BT off, the headset is disabled too, how can i always let the headset enabled with or without the BT signal?
Hi All!
I just upgrade my MDA III from WM2k3 to WM2k5 (TuMA 1.4).
All looks very good, but I founf the following problem:
I configure my MDA to use bluetooth hadsfree. When I push the power button to switch off my device, if I receive incomming call, rings only device, but not my hadsfree. When turn on MDA, i see that chackbox indicating on/off bluetooth is unchecked, i.e. mu bluetooth is off. I need to check it again to enable communications between my hadsfree and MDA.
But when my device is turned off, this happens again. In this case i cannot use my bluetooth handsfree, I need to receive phone calls from MDA, and every time manualy turn on bluetooth.
Are there any solutions to fix this problem?
I have an annoying problem, when i start the bluetooth on my iis the icon shows as connected but the bluetooth settings (Turn on bluetooth and make device visible) untick them selves meaning i am not connected. Also the blue led does not flash...
The only way i can get the blue tooth working is by doing a soft reset, after a while though i will not be able to start the bluetooth so need to soft reset again...I am running WM5 and the phone is an O2IIs
Any ideas anyone
Im trying to get the radio on using a Blue tooth head set, but the phone asks for the wired headset. Has any1 a solution to get it on without using the headset?
There is a registry key 'Headset Connected' = 0 or 1 or something similar, sorry cannot remember what it is - I think its under the HTC keys in HKLM..
It didn't work for me when I tried it without the wired headphones connected and I don't I don't have a bluetooth headset to try it out with...
I don't think you'll get any reception anyway since the wired headset acts as the antenna but good luck all the same
WoW, thanks for a fast reply.
this is your registry key:
### AUDIO BOOST ENABLED ALSO WITHOUT HEADSET, KEEP IT! ###
### remember also to configure it in BoosterAudio program
HKLM\System\State\Hardware\Headset = 1
but without an headset plugged-in you wont find neither a station
bye,
davide
why would you want to access the radio without a headset plugged in? you have no antenna to recieve the signal anyway lol
Hello
I would like to use the radio as followed:
Connect a cable to the usb-connector (to have an antenna)
Listen at the music with a bluetooth headset (to have more freedom)
Is this possible ?
Could I use any usb-cable ?
Perhabs even an solar-or batterie driven charger?
That would be usefull in long bus-travelling, were I could store the diamond in the seat-pocket in front of me, and walk around with the headset on!
Thanks for suggestions
jangs said:
Hello
I would like to use the radio as followed:
Connect a cable to the usb-connector (to have an antenna)
Listen at the music with a bluetooth headset (to have more freedom)
Is this possible ?
Could I use any usb-cable ?
Perhabs even an solar-or batterie driven charger?
That would be usefull in long bus-travelling, were I could store the diamond in the seat-pocket in front of me, and walk around with the headset on!
Thanks for suggestions
Click to expand...
Click to collapse
Why don't you put the phone in your pocket and walk around?
Is this possible?
Click to expand...
Click to collapse
no way, just tested
hello friends,
my logitech headset bluetooth seems to working properly,
it is properly recognized and function without problems until i shut the headset but ,when I turn it on again, the system does not recognize anymore. I have to remove the headset of the list from bluetooth devices and i have to register again on the system... to use it properly (until next headset shutdown).
Of course this does not happen wm6.0 original. I use Kavana rom (modified by Rickwatt).
someone know a remedy for this bug?
Thanks brothers
fwood said:
hello friends,
my logitech headset bluetooth seems to working properly,
it is properly recognized and function without problems until i shut the headset but ,when I turn it on again, the system does not recognize anymore. I have to remove the headset of the list from bluetooth devices and i have to register again on the system... to use it properly (until next headset shutdown).
Of course this does not happen wm6.0 original. I use Kavana rom (modified by Rickwatt).
someone know a remedy for this bug?
Thanks brothers
Click to expand...
Click to collapse
When you shutdown your headset, turn off bluetooth then back on then, turn on your headset, give it a try as thats what i do.
Generally also open up media player after headphone sync
Thank you for your reply Stylez.
I tried but unfortunately without success !If I'm going in bluetooth settings and select "set as heands-free" ... nothing happens. With the WM6.0 rom was in this way and the headset was recognized! I tried to turn off and on ..many times bluetooth and headset..... still nothing !
I must delete headset in the list and register it again!
I'm having same prob.