hi guys i have just purchased a haicom gps system and i cant seem to get it working it is attached to a pad holder and is plugged into the side of the holder. i am also running mamopolis but i cant find it on the gps info software that is attached. what should i do.
regards kevin
Make sure that beams is unchecked under settings/connections/incoming beams. Make sure any driver for external keyboard, if you have one, is disabled. Your settings will be Com 1.....nmea 4800.
haicom
thanks very much crusin thru i will give it a go.
regards kevin
Related
haveing a problem with my gps mouse in tom tom
under GPS i pick "serial cable on COM1"
and i get the error "cannot open COM1: port dose not exist"
im shure this was the setup on my xda2
any ideas?
yes deffo the same setup on my xda2
is the port on the bottom of this xda2s somehow setup diffrent?
can i set the com port that the bottom connector uses ?
if i cant fix this i will have to send the XDA2s back to o2
as i use tomtom for my work and thats the app
i use 90% of the time.
HELP
Go to settings/connections/beams, make sure the "incoming beams" box is unchecked, it will then release com 1.
cool thanks m8
IT WORKED
HELLO,GUYS
JUST INSTALL THE TOMTOM NAVIGATOR ON MY DEVICE--XDA lls
GOT A CRACK MAP FILE AND THEN ACTIVED IT.
HOWEVER WHEN I RUN IT,THE ''GPS DISABLED''
I CAN NOT TRACK MY CURRENT LOCATION!
HOW CAN I FIX IT UP?
THANKS
DO I NEED A EXTRA GPS RECEIVER?
I THOUGHT THE XDA lls ALREADY GOT A ONE, ISN'T IT?
Nope, you'll need an external GPS receiver
Maybe you mistook GPRS for GPS ?
and : NO NEED TO SHOUT !
hi,thanks
OK! forget the tomtom
if I just wanna a tool to help me track where I am normal when I am a tourist.
what kind programme will you help me advising?
You have the right program, you are lacking hardware, namely a gps receiver.
cheers.
where I can get a valuable one?
The cheapest place that I found is on ebay www.ebay.co.uk
all right!
whcih brand is ok for me ?
do you think the GPS receiver will be a little big only for handy?
I use a BT Polstar receiver on my MDAIII, works great, no problems. eBay 70squid
ski
Hi All,
I have a i-Mate PDA2K-EVDO with the following specs:
ROM:2.03.00 WWE
Radio: HA01_140
Ex ROM: 2.03.11 WWE
Currently with eXpansys FSE9 Car Kit (Includes integrated GPS reciever) URL"http://www.expansys.com.au/product.asp?code=124312", with ALK (Travroute) CoPilot Live 5 for PPC.
The issue that I am having is that when the phone is docked in the car-kit all call functions work fine (except for volume being a little low, but that may be spk position), however I cannot get the GPS software to communicate with the reciever. I am not sure whether the com-port that is used to communicate with the reciever is only being half-opened (or not remaining open).
I have tried modifying the selected COM settings and am currently using (COM 1, 4800) which appears to have some communication with the device. When the unit first is powered-up the GPS recieving light is on (steady) and when GPS location is established the light starts flashing. I have installed GPSInfo (for WM5) and am able to scan ports to establish COM1, 4800 as the connected port. When I then press the "Cold Start" button the GPS reciever resets, and then goes through the re-establishment phase, but no GPS data is being parsed.
To top things off, I did manage to get the CoPilot software to work for all about 5 mins. So I am thinking that this may be a port issue (or something with the reciever).
Can anyone provide some help with the following:
1 - A utility that can check com port activity, and see what is happening at this level.
2 - Some insight as to what other programs may use the same ports as COM1 - As I believe that it is serially emulated as a COM.
3 - Any other insight would be greatly appreciated.
Thanks in advance.
pro-integrator said:
Hi All,
I have a i-Mate PDA2K-EVDO with the following specs:
ROM:2.03.00 WWE
Radio: HA01_140
Ex ROM: 2.03.11 WWE
Currently with eXpansys FSE9 Car Kit (Includes integrated GPS reciever) URL"http://www.expansys.com.au/product.asp?code=124312", with ALK (Travroute) CoPilot Live 5 for PPC.
The issue that I am having is that when the phone is docked in the car-kit all call functions work fine (except for volume being a little low, but that may be spk position), however I cannot get the GPS software to communicate with the reciever. I am not sure whether the com-port that is used to communicate with the reciever is only being half-opened (or not remaining open).
I have tried modifying the selected COM settings and am currently using (COM 1, 4800) which appears to have some communication with the device. When the unit first is powered-up the GPS recieving light is on (steady) and when GPS location is established the light starts flashing. I have installed GPSInfo (for WM5) and am able to scan ports to establish COM1, 4800 as the connected port. When I then press the "Cold Start" button the GPS reciever resets, and then goes through the re-establishment phase, but no GPS data is being parsed.
To top things off, I did manage to get the CoPilot software to work for all about 5 mins. So I am thinking that this may be a port issue (or something with the reciever).
Can anyone provide some help with the following:
1 - A utility that can check com port activity, and see what is happening at this level.
2 - Some insight as to what other programs may use the same ports as COM1 - As I believe that it is serially emulated as a COM.
3 - Any other insight would be greatly appreciated.
Thanks in advance.
Click to expand...
Click to collapse
Hi there,
Not too sure if this'll help but with TomTom 5, you need to disable incoming beams on the Start\Settings\Connections\Beam to enable the Hard-Wired GPS to be read..
Try it and let us know the outcome..
Cheers!
Still No Good
Hey Mr Philly,
No luck with the Beam Settings. I even went as fas as Hard Resetting the device :x as Active Sync to Exchange stopped working this morning....
Any other ideas?
Thanks again for your response.
Paul.[/quote]
Paul, you mentioned specificaly that you loaded GPS Info (for WM5) is this the OS you have on the device? if so the GPS applet in the control panel / connections tab might need playing with - BTW I should have mentioned as its a wired GPS unit leave the Receive all beams OFF on this device - Mike
Interesting Point
Hi Mike,
Thanks for joining in on this thread.
I have disabled beams on the device.
THe GPSInfo app loaded was WM5 although I only have WM2003 SE. I have searched through multiple ng's to find a 2K3SE version, but all seem to point to the new version.
This was also the file provided my the distributor of the car-kit & cradle. The GPS unit is integrated into the Car Kit, so that is what i refer to as hard-wired (opposed to GPS).
As for the applet, I do not have a GPS applet in the connections section :?:
Can you provide any more informationon this point.
Thanks again,
Paul.
Disregard it then, I thought you might have loaded up a 2005 OS by chance , this has no bearing on the problem on your device - more thinking time required - Mike
Re: Still No Good
pro-integrator said:
Hey Mr Philly,
No luck with the Beam Settings. I even went as fas as Hard Resetting the device :x as Active Sync to Exchange stopped working this morning....
Any other ideas?
Thanks again for your response.
Paul.
Click to expand...
Click to collapse
Hi Paul..
Apologies.. I also need more thinking time.. :lol:
If I think of anything else, I'll get back to you..
i installed TomTom Navigator 6.020 SD BENELUX V660.1219
the program works,
it only cant find my gps device :s
some help would be much appreciated
Have you considered searching for this one - I have answered the same question at least 3 times to date!
Other NMEA Device
Baud Rate 9600
Comm Port 4
Mike
I was having a problem with that also.
It didn't matter if I was in the middle of an empty field running around with the thing in the air like an idiot, the internal antenna was too weak.
Now if I was in the car, the thing would pick up a signal no problem.
After looking into alternatives - like an external antenna - I settled on this:
I just picked up a BT-359W Bluetooth GPS Receiver for 85- Euro new.
The only difference between the BT-359W & BT-359S is the design on the top.
I made sure the battery was 100% charged before I turned it on (old habits die hard) and after spending 5-10 minutes trying to configure the Bluetooth on the HTC P3300 - I am a newbie when it comes to this new technology - it was able to get 3 satellites while I was in the house right away.
The thing is very small also - 82 mm x 41 mm x 13.4 mm (Inches: 3.22" x 1.61" x 0.52").
I would have to say that this is a great alternative to a wired antenna.
Here is a review I read before making my final decision: GlobalSat BT-359 Bluetooth GPS receiver review
Click to expand...
Click to collapse
Originally posted --> HERE
What a waste
Looks like you have a lot of money to burn, or whats the point of having a P3300 (with a bult-in GPS receiver - SIRFIII BTW) and then buying a bluetooth external GPS (basically another SIRFIII) ? cos its external ?
AD10 said:
Looks like you have a lot of money to burn, or whats the point of having a P3300 (with a bult-in GPS receiver - SIRFIII BTW) and then buying a bluetooth external GPS (basically another SIRFIII) ? cos its external ?
Click to expand...
Click to collapse
You missed the point completely.
The internal antenna was too weak.
When I am in a car, I have no problems at all getting a satellite fix.
The reason I bought an external GPS receiver is because I am not in a car all the time when using the GPS.
Longhair said:
When I am in a car, I have no problems at all getting a satellite fix. The reason I bought an external GPS receiver is because I am not in a car all the time when using the GPS.
Click to expand...
Click to collapse
That doesn't make sense at all, it should be the other way around. Inside a car the signal will allways be weaker than outside, because of the surrounding metal.
grun said:
That doesn't make sense at all, it should be the other way around. Inside a car the signal will allways be weaker than outside, because of the surrounding metal.
Click to expand...
Click to collapse
Thanks Grun, I thot I was the only one missing the point...and crikey what a way to shout your ignorance.
grun said:
That doesn't make sense at all, it should be the other way around. Inside a car the signal will allways be weaker than outside, because of the surrounding metal.
Click to expand...
Click to collapse
completely agree, what you're saying doesnt make sense unless you were in some very dense forest with all the trees in leaf, but you say you were in the middle of a field.
im about to install tomtom on my orbit so will see what its like as i used to use a bt gps reciever on my xda IIi
hello
i have installed tomtom ver 5
and i have to say that it works a treat..
it takes about a minute to register on the GPS but it does work well form inside the car aswell as outside the car.
The settings i use are
GPS Program Com 4
GpS Hardware Com 0
and keep the 3rd tab option checked ie pocket pc controlling access
On the GPS setting in tomtom select other NMEA device and choose Com 4
First time use will take about 5 mins so keep the phone still then after should take less than a minute.....
hope it helps
Tomtom not working
I have tried endlessly without success to get the tomtom on my orbit working. It keeps saying 'no gps device found'. When I select 'Other NMEA device' i dont see com port 4 as one of the options, i see com2 and serial (i think).
I thought maybe the software was not properly installed when i read about the com 4 thing and so uninstalled it. However I bought the phone (brand new) with the tomtom from ebay but now i cannot reload the tomtom as it keeps crashing during install.
Any ideas on what next I can do
have you changed the hardware port to com 4 first?
start>settings>connections>gps
then on first page GPS settings it asks what program port form the drop down list select com 4, that should then enable TomTOm GPS settings to display com 4.
remember once you have selected settings connect your phone to PC via actie sync and on
start>programs>quick gps
select menu and select update automatically when connected via active sync
this speeds up the process of finding the satelites and the data is usually valid for abut 3 days, so it does help to locate satelites quicker.
keep the phone still for about 5 mins and it should work..
thanks
l6cum
PS i am using TomTom 5, but the procedure should be the same
hi,
Go to mininova.org and download Tomtom Navigator 6 of it. It might take a couple of days to download sometimes. After you download follow the instructions and it is all user friendly. If you want any help don't hesitate to get back to me. If you want a copy in a CD send me a SAE so that I can write it on a disc and send it to you
Bear with me......
I have WM6 running, but when I connect to my laptop via BT it says there is only the Serial connection available, now I am being thick? As I cannt get the laptop to send things via BT OR the phone to recieve via BT, by things I mean photo's and vid clips etc etc, but always fails.
I have paired them repeatedly and deleted connections and made connections and everything.
So I am at a loss, am I missing somthing obvious or is it more problematical? I guess it could even be the XP BT stack, but thats next on the list to check.
Hints, tips and advice as ever greatfully received
Deech
Hi, sounds like a very annoying problem, i can only think of 2 things:
1. make sure that 'recive all beams' is ticked on your PDA, this sets the location etc for when you recive files in bluetooth i think.
2. uninstall your bluetooth in XP and reinstall it to another USB port.
I hope this helps, i cant think of much else to help
ummm.... 'receive all beams' would be infrared.. not bluetooth
install schap's advance config tool (should find it under the cab collection thread) and there's an option to enable OBEX file transfer. After you do that on your trinity and soft reset, you should be able to send/receive files
Thanks will do.
I wonder if I should upgrade the software too? I have MinRus's original WM6 onboard atm, or perhaps it's LVS's..... I really ought to pay attention, and now I see that there are loads of "newer" ones out and about.........
/me goes to ferret around the fora
"ummm.... 'receive all beams' would be infrared.. not bluetooth"
no it's both
that's what i thought too, its for both.
when i send a file it's : "beam file" you see your infrared and bluetooth connections.
and maybe this: visible for others in bluetooth options? will help ?
check the same for your laptop maybe...