cannot open COM1 - MDA III, XDA III, PDA2k, 9090 General

haveing a problem with my gps mouse in tom tom
under GPS i pick "serial cable on COM1"
and i get the error "cannot open COM1: port dose not exist"
im shure this was the setup on my xda2
any ideas?

yes deffo the same setup on my xda2
is the port on the bottom of this xda2s somehow setup diffrent?
can i set the com port that the bottom connector uses ?
if i cant fix this i will have to send the XDA2s back to o2
as i use tomtom for my work and thats the app
i use 90% of the time.
HELP

Go to settings/connections/beams, make sure the "incoming beams" box is unchecked, it will then release com 1.

cool thanks m8
IT WORKED

Related

wired gps cant connect tomtom5

I have an SPV M2000 and i have just purchased a wired gps tomtom5. After disabling the IR beam my gps still doesn't connect. i have hard reset the unit to make sure i have no other drivers interfering but it still doesn't connect.
all the help lines tell me to disable ir beam but it still doesn't work.
Does anyone know anything more about this issue?
Hey Kitrider, I apologise in advance if I'm insulting your intelligence but have you selected it in the preferences? I don't have a Tom Tom reciever but I still select it and it works with Navigator 5.
In Tom Tom go to preferences, select GPS status, if you have no signal (assuming its connected!) then select configure and select each of the others in turn to see if you get signal. Bear in mind, sometimes it takes 15 seconds or so for it to show.
TT5 andd GPS..
Regardless as to what GPS device you have (wired/BT), if you go to the GPS status screen (from where you can configure the GPS) there is a blue and yellow circular icon in the top right hand side of the screen (below the time), if this is "turning" then you have selected the correct COM port and data is being received - GPS signal or not...
What COM port have you chosen (try saying is is a TT Wired GPS as that defaults to COM1) - or did you say it is a TOMTOM model?
If it is and you can't getthat to work , try selecting other wired...
Yep i am selecting it in the TT5 preferences i've tried all of them and left it for over 30 secs on each one. The blue and yellow disc never spins though. I get a message which looks like a pocket pc windows alert box (identical to when it connects to activesync) that says it is trying to connect. this flashes up a few times then it comes to a bigger windows message box that says that the device cannot connect to the computer. the port may be busy or unavailable. Restart device and try again.
After restarting (hard or soft) there is no difference.
The gps is not a tomtom version but is one that apparently works according to PDAMODS.com, whom i bought it off. They reckon that there is something wrong with the m2000 and told me to get orange to replace. But orange are being very slow and not forthcoming with this request. basically as i have no proof that there is something wrong.
Any ideas please???????
i'm flumuxed!!
just to add i#m selecting other wired gps, baud rate 4800, serial cable on com 1.
but have tried all the options

wm 5.0 totom & 5.100 & Altina GPS

with tomtom 3.0 it was simple to connect with tomtom 4.0 it was again simple then came tomtom 5.0
had to select wired gps and then chose com port 6 with tomtom 5.0 with wm 2003se. with wm5.0 its all different cant get it to synch with my gps any help will be great. im sure there will be a lot of people strugglign with this
Same problem here but using a Pharos 360 with the Bluetooth docking station. With WM2003SE Tom Tom shows a lot more com ports. It used to have Com5 and Com6 and the bottom of the configuration screen. Now it only has Com1 Wired connection, Com2 and COm9.
When pairing the GPS to an outbound serial port you can not use com9, Com2 or Com1. If you pair the GPS to new port like com6, Tom Tom still does not offer com6 as an option.
So I figured you had to use the GPS control panel item to map another Com port to the actual GPS com port. But still no joy. After creating a new software com port it still does not show up in Tom Tom. If you use one Com2 or Com9 that Tom Tom does have options for, it does not connect.
Anyone got this working??
Shawn
Please check your PM.
Thanks,
Darren
solution found for the above
go to bluetooth and pair the gps with the phone. enter passcode if required then click on new outgoing port and then select com port 6.
open tomtom then select configure gps then select other buetooth gps. you should now see com port 6. select this and everything should work now.
That does not work for me. Once I pair my GPS and assign it a com port, the com port will NOT show up in the Tom Tom GPS configuration screen.
Shawn
tomtom
need to ensure you enable the serial connection when it asks you. for me it worked on com 6 and should be same for you no matter wat bluetooth gps you are using as it says this on tomtom website. instead of using wired gps like in 2003se we need to use bluetooth gps option and it should work. seems to work fine for me. do a breakdown of what you are doing cos we may find something i am doing that you are missing out or something you are doing which is wrong.
by the way i have beams turned off and i have not fiddled with com ports on the gps setting icon in settings menu. the application and hardware port have been set to none. we just need to apply the gps port to com 6 upon creation of partnership
Thanks for the reply
This is what I am doing.
Settings->Connections->BlueTooth
On Mode tab. Turn On Bluethooth
Click Device Tab
Click new partnership
Pharos iGPS-BT shows up. I select and say next
I check the serial Port service and click save
I click on Com Ports tab
I click on new Outgoing Port
I select My GPS and select Com6
I have tried with the "Secure connection" on and off
Click Finish
Now the comm port tab shows
Pharos iGPS-BT (COM6)
New Outgoing Port
New Incoming Port
Click Ok to close the BlueTooth manager
Click X to close the settings window
Run Tom Tom
Click on the GPS Bars to get to the status summary
Click on the bars again to get to GPS Status
Click COnfigure
Select Other Bluetooth GPS
Press Continue on next screen
Now all the shows up is
BT UART
COM2:
Serial Cable on COM1:
COM9:
Ir on COM3:
So I can not select Com6 as it is not in the list.
i have the problem....
can,t anyone welp. pls
think i have a solution
slammers et al,
switch off 'Receive all incoming beams' in Settings, Connections, Beam.
in Settings, Connections, Bluetooth, Services select Serial Port - in mine 3 are ticked:
Enable service
Authentication(Passkey) required
Encryption required.
click Advanced, Inbound COM Port is 5, Outbound COM Port is 6.
switch on your bluetooth GPS receiver.
open Bluetooth Manager and double tap your GPS receiver, if it's not in Bluetooth Manager then pair the device and create a serial connection by clicking New, Explore a Bluetooth device, select your device to make a serial connection shortcut.
start TomTom, go to 'Change preferences', Show GPS status, Configure, select 'Other Bluetooth GPS' and select Serial port 6....click done....in the GPS Status window you may see that it is connected....if not do the next step.
click done, exit application.
soft reset device.
switch your bluetooth gps receiver off then on.
start TomTom, leave it for 30 seconds....it should connect to your GPS device...if you have the older TomTom GPS receiver you'll be able to tell that it's made a connection by the constant blue light being displayed on the gps receiver.
if you have no luck with selecting 'Other Bluetooth GPS' try selecting 'Other Cable NMEA GPS', choose GPS baud rate 4800 and then 'Bluetooth Serial Port 6' in the TomTom configuration screen.
i know it's a bluetooth device but this has been a problem prior to version 5.10 of the tomtom software and people have had success using this option and connecting.
i've had success with a few different configurations and have helped a few people get theirs working.....also there is a claire on this board who i went through a painstakingly long back an forth post with and i'm still not sure if she got it working....but i've just learned how to get mine working where it turns on the bluetooth automatically and switches it off also...and prior to this post i had it connected using the 'Other Cable NMEA GPS' instead of Other Bluetooth GPS....so good thing i turned it on and messed with my config while trying to explain how to modify yours.
good luck.
i dont have this opction on windows mobile 5 decoy 7....
you dont have that option?
no... mobile 5 have the BT like qtek s100.. very simple.... :shock:
but finely i have put on work the bt-338 on mY BA with tom tom 5
i do this:
seting-connections-bt then i partnership with gps
next
setings-connections-bt-com ports and make outgoing port with gps (com6)
setings.connections.bt.com ports and make incoming por (com7)
next
go to gps frome wn5 and put com7 in "software" live the menu of hardware as "none" and 4800 and ond the 3 windom put on
then opem de tom tom and open de pgs configuracion and use "other bt gps" and use the port com6...
work on me :lol: :lol:
good luck....
go to gps frome wn5 and put com7 in "software" live the menu of hardware as "none" and 4800 and ond the 3 windom put on
then opem de tom tom and open de pgs configuracion and use "other bt gps" and use the port com6...
Click to expand...
Click to collapse
Are you sure you mean softport 7 and set 6 in tomtom?
help
I am having this problem but the TyTn only lets me use Com 0 so I cant set it to com6.
WHen I am in TomTom it says there is no gps and when trying to configure it doesnt give me the right options.
help please

How to set a BT GPS receiver on Universal with WM5???

Hi y'all,
i have a BT GPS receiver that i used with my Qtek 2020 (before this was stolen... ).
Now i have a XDA Exec from O2, but i am not able to set the receiver!
Anyone has any tip for me?
Thanks a lot...
...no one can help me out...??? Please...
Check out this guide and follow from after installing tomtom and you should get BT GPS working with exec, I did!!!
ps search term used was 'tomtom 5.1 guide'
hope this helps!
http://forum.xda-developers.com/viewtopic.php?t=28386
Hello,
first the bad news: not every bt-reciever is working...
but you should try this way:
Connection-Manager
Enable BT
Setting (Connection-Manager) BT-Settings
Tab devices and ad new partnership (be sure, BT-Reciever is on)
Pair it with your Universal (pin is usuall 0000)
Tap Com-Ports: new outgoing Port (your BT-Reciever) set to com 4
Tap Com-Ports: new incomming port (your BT-Reciever) set to com 8
Now it should work!
Thanks for the tipo...now i don't have my GPS receiver with me...but tomorrow i will give it a try.
The only thing that i find strange is: when i try to set the outgoing port i find my BT receiver in a box, but when i try to set the incoming port i dont' find it anywhere.
Something wrong?
Oh...and also...i use the software "GPS View" for the connection with the BT receiver...which port should i open (the COM4, the COM8 or another one?).
I ask you this because i have 10 COM ports available (from 1 to 10), but i cannot open all of them, because some tell me "COM porte error" when i try to open it.
Thanks for your help...
can anyone confirm if haicom-405 bt works with dopod 900?
Hustladave said:
Oh...and also...i use the software "GPS View" for the connection with the BT receiver...which port should i open (the COM4, the COM8 or another one?).
I ask you this because i have 10 COM ports available (from 1 to 10), but i cannot open all of them, because some tell me "COM porte error" when i try to open it.
Thanks for your help...
Click to expand...
Click to collapse
As I wrote before:
Tap Com-Ports: new outgoing Port (your BT-Reciever) set to com 4
Tap Com-Ports: new incomming port (your BT-Reciever) set to com 8
Best wishes
Teja
jona69 said:
can anyone confirm if haicom-405 bt works with dopod 900?
Click to expand...
Click to collapse
I follow the tips ...outgoing port (COM4 - which the only port can be used other failed to open), incoming port (COM8).
But it doesnt work with my Garmin10 .... which work well with my previous XDAIIs. Anyone use Garmin1o with Dopo900?
Thanks
Usually, there's no need to setup an ingoing COM port: my Holux 236 receiver, for instance, works perfectly paired with my Qtek 9000 and only the outgoing COM8 setup'd.
The only thing to pay attention for is that TomTom have to be v5.1 or above (better if v5.21), in order to work properly under Windows Mobile 5.0.
Well...in my previous XDAII worked perfectly using the software MAPSONIC and the GPS VIEWER with my BT receiver (and just setting the outgoing port).
I tried to do like Teja told me in his answer (setting the outgoing COM4 and the incoming COM8), but it still does not work.
I will try to get a TOMTOM 5.1 software to give it a try...
solved...and i don't need to setup the ingoing port...thanks for the tips
Hi there! I have MDA Pro from T-mobile (UK) and until now I couldn't set a COM port appart of COM0 port for BT-GPS...
Now have COM4 for outgoing port and tom tom once is connected after 5 seconds is disconnected and again after 5 seconds is connected and again is disconnected and again......
I am using TT 5.21
Help please
I have set the outgoing port on COM8, no ingoing port needed and it works fine...although i don't have TOMTOM!!!
Orange M5000 and BT GPS and TOMTOM 5.21
I thought I share this just in case there are other like me out there.
I had an Orange M2000 with tomtom 5.0 and 512MB SD card.
I installed TT5 as normal on the PDA but the maps on the 512MB SD card.
I just got an Orange M5000 which is XDA EXEC and could not install TOMTOM 5.0 from CD. The SETUP kept on crashing on XP PC.
Here is the solution:
1) Put the SD card with the maps in M5000
2) Did NOT install TT5 from CD but downloaded navupd521.exe from the tomtom site and installed this on M5000 fine.
NOTE: I did not have to copy CAB files. I just installed this as normal from my PC with the USB cable
3) TT installed fine but I could not get it to recognise the BT GPS
I used the instructions below from the forum:
a) Turn on BT GPS
b) on PDA goto BlueTooth seeting --> New Partnership and supply the password (0000) to pair it.
c) Then in Bluetooth settings select the COM PORTS tab
d) Select Incoming port and set to COM8
e) and again in COM PORTS tab select Outgoing ports and select COM4
f) Start TOMTOM and goto Preferences and find GPS Configuration and select OTHER GPS and select COM4
It works every time... ALL my FAvourites etc are still there so no need to type them again.
So far WM5 and TT5 rocks. I will be testing it on the road with my Plantronics BT headset soon. With my old M2000, usually when TT5 is on the M2000 CPU does not have the juice and Bluetooth devices die or stop responding. Also when I stopped TT5 application the BlueTooth stopped.
We will see how M5000 improves on M2000
Thax...
i believe you shouldnt have a problem running your headset and bluetooth GPS together.
when i had a blue angel i ran TT3 with my SonyErricson Car Kit and the TT3 together and made vioce calls at the same time and even now with the Universal i can do the same! run them both together!
only thing is that occasionaly the TT5 seems to be a little behind my actual location if i have made/received a call luckily by only 30-40 yards so can still use the screen to see where my turnings are.
has anyone else found that and got the cure....
thanks

XDA Exec and Holox BT-321 GPS Receiver

hi there
new to this forum which looks very interesting. Hence asking answer for a problem.
i have bought a Holox BT-321 gps receiver which is blue tooth enabled and i am trying my xda exec to recognise it. aftre turning both devices on xda can see the receiver but puts a yellow question mark before its name.
when turn the gps software on ((Medion Navigator) it does not recognise presence of the gps receiver.
i have great hopes that out there some one does know the answer to this.
to me it appears a software conflict as xda can not install this receiver.
i have tried O2 but they politely refused and asked me to contact gps receiver makers who in turn say the receiver is working fine!!
i was about to pay for a software pathway for sale at ebay but it had been banned by the ebay.
so help please
mohammad asif
Assuming that you did set a port for it (not sure whether it's incoming or outgoing) on the Exec for the GPS unit, you'll probably have to set the port to see the GPS unit on the software also.
That's how I got my GPS unit to work with my software. Please note that the software and the GPS unit that I'm using are not the same as yours. So results might vary.
I too am having exactly the same issues with the Holox 321 and o2 Exec. If anyone has had success pairing a using these two devices and can post a step-by-step walkthrough on how to do it I'd be very grateful.
Thanks.
MDA Pro and BT321
I have got exactly the same problem. It seem that the bluetooth works but the GPS receiver is not recognised. I was thinking of it could be missing drivers or something along those lines
I'm seeing a trend...
hi all,
My m8 has one of them on an XDA2i and the only way we could get it working with TT5 was to set it up as other NMEA GPS on com 6, that did the trick
hope that helps
Thanks BBD, that may help. Trouble is though, I can't even get it to pair correctly. The Exec seems to go through the motions, but the blue light that's meant to flash whenpairing is successful just stays solid.
I also get the question mark appear next to the device in the list of BT devices. What OS is your friend using? WM5 or PPC2003?
hi m8,
he is using WM2003SE, he two has the question mark beside his device I think that just means it does not have a Windows Certificate nothing more, just cheked my TOMTOM device has the question mark too and that works fine
Matt
hi,
just double checked and this is how it worked, pair the GPS receiver up, then go into TomTom and use the NMEA devices with baud rate of 38400 then select bluetooth on com6 and bingo bango your off
cheers
Matt
I think my problem occurs before TT5 is even invloved. From what I've seen WM2005 is very different from PPC2003 as far as BT goes.
I search for a new device and the BT-321 is seen as normal. I select it then enter the sec. key; ok so far. then I'm ask what services I want to use (only "serial port" is available). I select this, then finish. At this point I expect the blue BT light to start flashing telling me I have a successful pairing, but it stays solid. I have tried creating a new outgoing port, but no change.
Until I can get a successful pairing my BT port doesn't appear in the list in TT5, so I can't select it.
I wish I could find someone who has successfully paired these two devices...
Bump.
I can pair my mini s to the bluetooth reciever, but not tt5
i have paired my bluetooth reciever with my xda mini s but when i go to select it in tt5 none of the comports correspond with any i can pair the reciever with. I have installed bttools but this hasnt helped either. someone suggested i needed to build a com port but i dont know where to start, and they also said its because its an xda that theres comport problems, i donubt im the first one with this issue. i pray someone can help me out, would be much appriciated.
email [email protected]
Same problem on my Wizard with the Gpslim 236. However, my fiend brought over his rikaline last night and it worked very quickly. Go figure. I think I'll be exchanging today.
I got the BT321 working with the Universal no problem.
It paired okay, gave me the COM Port option which I took, showed the icon with ? on it.
Going to the COM Ports tab, I created an outgoing port (COM0).
In TT5.21 (I think you need the latest version of TT5) I selected COM0 and after a while it found it no problem..
F.
paring xda exec + gps holux 236
i did pare the 2 after updating tomtom to 5.21 free from tomtom web site then u get com 8 were u can set the outgoing port from the xda ,voila
I have XDA EXEC and have successfully installed the Holux BT-321 Bluetooth GPS. It runs perfectly with a number of GPS applications - so I know the port/Bluetooth configuration is ok. I had to choose an unused com port (0 or 4 work fine). (Ports 1,2,3,6,7,and 9 seem to be already used by the XDA EXEC - so could not be seleted).
BUT (going back to the first post) Medion Navigator (4.2) does NOT recognise the new GPS port. Instead it has options to select ports com1,2,3,6,7,9 but not the "new" port where the GPS is actually configured!
Does anyone have any ideas about this?
After several hours trawling forums and trying lots of things here's what worked for me on an XDA Exec running WM5. In fact I was shocked when it worked! In return for this can someone please think up the next thing after Toothache! The WM5 bluetooth connection thing could also do with a re-write - as could the WM5/XDA Exec instructions/FAQs/help, etc... on BT:
If your aim is to get TomTom working AND you're using a non-TomTom BT GPS, try this (the TomTom GPS seems to install itself without much problem):
1. Pair the GPS with your device BEFORE installing TomTom, because the GPS port needs to be already setup on your device for TomTom to recognise when installed.
2. Then install TomTom
3. Launch the BT connection thing in WM5. Make sure the BT is discoverable (first tab). Select 'Security' tab and ensure 'Authentication (Passkey) required is checked.
4. Go to 'Devices' tab and select 'new partnership...' The pairing thing should find your GPS and will then ask for the passkey - select next WITHOUT entering anything even if there's a passkey. If you enter the passkey now you will not get step 5 which is a crucial milestone.
5. The device should now ask if you want to add the GPS to your list, select yes
6. The name of the GPS is shown. Ensure 'serial' port is checked and hit next
7. You will be asked for the passkey again - enter it this time
8. At this point the GPS may look like it's not paired. The lights may flash as if unpaired. You'll also get a question mark icon next to the GPS in your list. Not to worry.
9. Select 'com ports' tab and select 'new outgoing port'. You should see your GPS listed. Select it and hit next. From the list of ports select COM8. Make sure the 'Secure connection' is UNCHECKED - otherwise you'll be pairing everytime you start TomTom! Select Finish. You should see your GPS (COM8) listed in 'COM ports' tab.
10. Turn off 'device is discoverable' (first tab).
11. Now install TomTom. Having installed the GPS as above, TomTom will now know about COM8 i.e. where your GPS is to be found. If you hadn't done that first there would be no COM8 and no GPS connected to it as far as TomTom is concerned.
12. Turn on the GPS
13. Launch TomTom and go to 'preferences/ GPS Settings'. Select 'configure'. Select 'Other bluetooth GPS'
14. You should get a list of ports and with any luck you should see 'COM8' - select it and hit 'done'.
15. I think at this point the GPS page in TomTom came alive, or maybe I had to restart TomTom - can't remember. And it works thus far!
Toothache - what a palaver!
BT/GPS Problems
Hi,
I have a program that can sort out the com port problems between the bluetooth and gps software.
I have included the program as an attachment, just unzip it into your PC, make sure you reboot your PDA, sync your PDA to the PC and run setup.
Problems solved.
Cheers,
John
bigbird49 said:
Hi,
I have a program that can sort out the com port problems between the bluetooth and gps software.
I have included the program as an attachment, just unzip it into your PC, make sure you reboot your PDA, sync your PDA to the PC and run setup.
Problems solved.
Cheers,
John
Click to expand...
Click to collapse
Hi,
I`m a new member.After installing your litle tool i can`t start this application and also can`t find it under programs or anywhere else?
I`m using a T-Mobile MDA Compact II with WM5 latest ROM, a Holux BT321 and TomTom6. `have expierences with BT and XDA`s using TT5 for a long time.
After upgrading to new devices and new sw i have the following problems:
I can connect the BT321 as a BT Mouse and get a good signal.Using TomTom6 the navigation works with a delay of round about 100 meter. I`m looking for a resolution to connect the BT321 via the NMEA Interface.
regards
AK
____________________________
MDAc II
WM5
BT321
TT6
Britishbulldog said:
hi all,
My m8 has one of them on an XDA2i and the only way we could get it working with TT5 was to set it up as other NMEA GPS on com 6, that did the trick
hope that helps
Click to expand...
Click to collapse
I have tried your advice and it works a treat, thanks to you and everybody else who contribute to this forum

Newb question- GPS

Hello all,
As you can see by my post count I am a newb so please cut me some slack
With that said, I bought a Holux GPSlim 236 bluetooth GPS reciever and I am having trouble getting it to work with google maps..I just want to have some type of gps working on my phone no matter what program it is..Can someone please shed some light onto how I can get it set up with my phone or what is the best program to use with this phone?? Any help is greatly appriciated..
Try this http://forum.xda-developers.com/showthread.php?t=293397
after pairing your GPS device and setting up a comm port for it as follows:
Start/Settings/Connections/Bluetooth.
Make sure Bluetooth is set to "On".
Menu/Devices
Menu/New
Select your GPS device from the list and press Next.
Enter the passkey for the Bluetooth GPS. For example, 12345678.
Next
You should get a message box saying "Your Smartphone has connected".
OK
Next
Check the "Serial port" checkbox.
Done
Done
Menu/COM Ports
Select your GPS.
Menu/New Outgoing Port.
Select your device and press Select.
You will see a COM port that has been chosen for your GPS. For example, COM6.
Done
Done
Done
Now your GPS is set up on COM6.
I have the exact same setup. What finally worked for me was the com port config app found in this thread (http://forum.xda-developers.com/showthread.php?t=293397&highlight=google+maps). Google maps works great with gps, providing you have a phone signal. Have fun.

Categories

Resources