Imate PDA2k 'No Service' issue! Plz help! - MDA III, XDA III, PDA2k, 9090 General

Imate PDA2k
ROM Version: 1.40.00 WWE
Radio Version: 1.12.00
Protocol Version: 1337.42
ExtROM Version:1.22.162WWE
Hi guys, sometime my PDA2k cannot be registered to Vodafone Network, 'No service' would display and I cannot make any calls unless Hard reset the device, and everything just works fine after hard reset, Anyone here can help or met the same issue as me? Thanks.

Exactly the same problem - O2 in the UK.
I updated to the latest ROM from 02 and it cured the problem for about 24 hours, now I get the message:
Unable to read the setting from the network
Click to expand...
Click to collapse
Aaaaaaaaah!

I have just updated to latest version and 'No service' issue has gone ,, but met new problem is 'headphone silent' sometimes when make a call , I have to soft restart it to get my phone back

I cannot get mine going with a hard or soft boot and upgraded ROM from o2.
Have tried consumer and corporate install to no avail

Hi Newmate, have you had any recurrance of the "No service" problem since your ROM upgrade. I live in Trinidad and in certain locations I get "no service" on my PDA 2K but if I switch the SIM to another phone I get a strong sognal.
I have the same ROM versions that you do and my operator oalso operates in the 1800 band.
I am searching for a solution.

Related

Odd device (ROM) info

HI
I've had my o2 xda2 since it came out in the UK Nov 2003 and I haven't reflashed the ROM or done any thing like that. I even got O2 to network unlatch it for me. (This was before the unlock tool) I was surprised to see the following device info when i did a soft reset.
ROM version 1.03.00 USA
ROM date 09/24/03
Radio Version 1.05.12
Protocol version 1337.12
the bit that surprised me was USA in the ROM version.
I've been in Toronto since May 04 on Fido has my ROM been upgraded without my knowledge over the air/or when I use my wifi card or is this a really old rom as i got one of the first xda2's that came out in the UK.
Should I upgrade the rom with o2 latest update?? or use a different ROM
The XDA locks up rarely, the only problem is when you go out of signal range (ie on the underground subway) the xda2 sometime can't lock back onto the network and so a soft reset is needed.
I look forward to your pearls of wisdom.

Please Help, my Blue Angel Phone died.

Hi all,
First of all I want to thank you for your time.
I bought a Blue Angel device from a friend of mine but unfortunately I'm not so sure who made it.
It does have the bluetooth, camera on the back, wireless wifi, etc.
About a week ago, the phone function died. I verified that it wasn't the GSM card because when I moved the GSM (Cingular) to a different cell phone, it does work.
I then found out that from the device information, I only saw the ROM version, ROM date and ExtROM version BUT the Radio version and the Protocol version are blank.
I am attaching the devicedata.txt.
With that in mind, I have tried to upgrade the ROM and the Radio. I'm currently running the O2 ROM with the following information:
1. ROM version 1.12.62 WWE
2. ROM date: 10/04/04
3. Radio version: Blank
4. Protocol version: Blank
5. ExtROM version: 1.12.178 WWE.
When I tried to upload the Radio ROM, it seems to upload it, no error messages but still the radio version information is blank and my Blue Angel is still not recognizing as if the radio is off.
I tried to upload other ROM, like Imate PDA2k, Siemens SX66, etc but I couldn't because sometimes it kept complaining about country id or language id not correct.
I really appreciate any helps, inputs on this matter. I'm kind of dead on the water without my phone...
Thank you so very much,
Tambeng
Upgrade everything, not just the radio rom, you have a really old stuff running there...
Download upgrade from. clubimate.com and install it. But only of you have PDA2K.
I did try upgrade it to the following:
With that in mind, I have tried to upgrade the ROM and the Radio. I'm currently running the O2 ROM with the following information:
1. ROM version 1.12.62 WWE
2. ROM date: 10/04/04
3. Radio version: Blank
4. Protocol version: Blank
5. ExtROM version: 1.12.178 WWE.
But after the upgrade the Radio version and the Protocol version went blank again.
Do you think the fact that the radio version is blank is the cause of my phone to die?
Has anyone else since this issue before?
Thanks,
Tambeng
plemax said:
Download upgrade from. clubimate.com and install it. But only of you have PDA2K.
Click to expand...
Click to collapse
I tried to download but it says about the model is not correct.
btw: what does it mean by a ROM that says cooked?
Thanks,
Tambeng
No, no. Try to download from official website. What is your PDA call? It must be says some where on it.
btw: what does it mean by a ROM that says cooked?
Click to expand...
Click to collapse
It means that somebody made it by himself - not official. People take different parts from different ROMs and put them together into one ROM. You don't need things like this right now.
tambeng said:
Do you think the fact that the radio version is blank is the cause of my phone to die?
Click to expand...
Click to collapse
Very possible. What is wrong with your phone exactly? It's searching for signal or......?
It's actually really interesting that it didn't have any brand at all on it.
It just says, PocketPC on the top right corner. Can I identify the maker from the IMEA? I can share the IMEA number.
As for the phone, it doesn't even search for a signal at all. It just have the exclamation mark, like "!".
Thanks for your help,
Tambeng

Radio 1.06.00 Upgrade

Hi,
Just uploaded the radio 1.06.00 only upgrade to the ftp:
ftp://xda:[email protected]/Uploads/Universal/Universal Radio Only Upgrade 1.06.00.rar
It seems that it's faster to ring and to answer...
ncruz said:
Hi,
Just uploaded the radio 1.06.00 only upgrade to the ftp:
ftp://xda:[email protected]/Uploads/Universal/Universal Radio Only Upgrade 1.06.00.rar
It seems that it's faster to ring and to answer...
Click to expand...
Click to collapse
I understand that you hadn't to hard reset the jasjar after upgrade it with this radio. Please confirm and if is any tricks to apply.
As you can see below, I have radio 1.04.10 installed. Anybody know the differences between these 2 loads?
Thanks in advance (obrigado). BetoX
---------------------------
iMate JASJAR
ROM Version: 1.13.53 WWE
ROM Date: 23-09-2005
Radio version: 1.04.10 (MANUAL UPGRADE)
Protocol Version: 42.36.P8
ExtROM version: 1.13.137 WWE
No tricks, no hard reset, just a normal radio upgrade...
Hello
Has anybody tryed this on the Xda Exec?
Regards
Gigino
ncruz said:
No tricks, no hard reset, just a normal radio upgrade...
Click to expand...
Click to collapse
I don't know what pocedure you guys use, because to me happens allways the same... have to hard reset it, upload the original ROM and following it upgrade to the latest radio...
Can somebody explain the complete procedure without having to hard reset it?
Thanks in advance (obrigado). BetoX
---------------------------
iMate JASJAR
ROM Version: 1.13.53 WWE
ROM Date: 23-09-2005
Radio version: 1.04.10 (MANUAL UPGRADE)
Protocol Version: 42.36.P8
ExtROM version: 1.13.137 WWE
Where did this version of radio rom come from? Can anybody who has done the upgrade comment on the version? anything better or worse?
gigino said:
...
Has anybody tryed this on the Xda Exec?...
Click to expand...
Click to collapse
I've been using radio: 1.06.00 since Tuesday or Wednesday without problems. Hasn't fixed nor broken anything as far as I can see.
Radio 1.06.00 was issued as part of the recent German MDA update.
[No message]
Yes, ist working, had to do the update several times, like 10x, before it was installed, soft reset ......and.....IT'S ALIVE
thanks
Thanks, ncruz! the radio upgrade on my MDA Pro worked flawlessly on the first attempt. My device information now shows:
ROM version: 1.13.69 WWE
ROM date: 10/12/05
Radio version: 1.06.00
Protocol version: 42.37.P8
ExtROM version: 1.13.162 WWE
I was hoping the radio would solve a couple of issues I've mentioned on this thread:
http://forum.xda-developers.com/viewtopic.php?t=38876
but, unfortunately the wireless manager and bluetooth issues still persist.
Hi,
Removed SD and SIM cards.
However, as with my all Universal previous ROM upgrades (only Radio till now), I got several errors (114; 150;...) till succed. About 15 and long attempts.
Did you experience a similar problem?
Could it be related with device bootloader version (mine is v1.00). Does someone has a newer one?
Between some attempts and errors, I need to 'soft reset' or 'cold boot' in order to get a different error, and finally a succesfull attempt.
I've a Qtek 9000 with a TMN SIM (Portugal) and it works fine after upgrade.
Just in case, I want to give up in future similar operations, does someone knows how to get rid of the bootloader? Does an Hard Reset resolves? Is there any other way?
Error 114: Radio ROM update error
Error 150: ROM upgrade utility error
I "up?"graded to radio 1.06.
I found it in some conditions slower than 1.04.10, and when I use NovosecSmartFilter, it freezes when a call comes althogh it worked with the previous radio ROM.
Just for you to know...
Tuningszocske said:
I "up?"graded to radio 1.06.
I found it in some conditions slower than 1.04.10, and when I use NovosecSmartFilter, it freezes when a call comes althogh it worked with the previous radio ROM.
Just for you to know...
Click to expand...
Click to collapse
I've noticed 2 times now (with hard resets between) that sometimes when I receive a call, my Contacts open and I can't close them. I can click the Start menu and run another app but then Contacts is brought to the front again. After enough clicking to close Contacts, the upper right corner quickly alternates between "OK" and "X" and I end up having to soft reset.
One thing that I did do differently is that I performed a soft reset prior to O2's extRom installation. Are there any 'fixes' in their extRom that I might need to manually install?
I'm thinking about going back down to 1.04.00 as I didn't have this problem prior. But I'd rather not downgrade.
I'm down?grading to 1.04.10 now....
Re: Radio 1.06.00 Upgrade - borged
ncruz said:
Hi,
Just uploaded the radio 1.06.00 only upgrade to the ftp:
ftp://xda:[email protected]/Uploads/Universal/Universal Radio Only Upgrade 1.06.00.rar
It seems that it's faster to ring and to answer...
Click to expand...
Click to collapse
Hi I did the supid thing of not actually following all the instructions,
I just installed update over a bluetooth activesync connection.
It never finished but after a soft reset my device sits with a grey screen
with the words Serial and v0.60 at the bottom.
I have tried to hard reset and soft reset but the device wont boot
Any ideas?
Eric
Re: Radio 1.06.00 Upgrade - borged
eappel said:
....I just installed update over a bluetooth activesync connection.
It never finished but after a soft reset my device sits with a grey screen
with the words Serial and v0.60 at the bottom.
Eric
Click to expand...
Click to collapse
It's looking for a serial (not available on Universal) or USB connection, so you'll need to connect to "ActiveStink" via USB cable. The "Serial" will normally change to "USB" when you plug USB in.
Unfortunately, I've never tried it with an *un-partnered* device stuck in bootloader mode - hopefully somebody else has.
ncruz said:
Hi,
Just uploaded the radio 1.06.00 only upgrade to the ftp:
ftp://xda:[email protected]/Uploads/Universal/Universal Radio Only Upgrade 1.06.00.rar
It seems that it's faster to ring and to answer...
Click to expand...
Click to collapse
Can u let me know whether i can upgrade on dopod 900 in singapore or this upgrade is restrict to a particular country.
cheers Taurus
can be used for Dopod 900 also...
the radio update is for all models of HTC universals...
Re: Radio 1.06.00 Upgrade - borged
eappel said:
Hi I did the supid thing of not actually following all the instructions,
I just installed update over a bluetooth activesync connection.
It never finished but after a soft reset my device sits with a grey screen
with the words Serial and v0.60 at the bottom.
I have tried to hard reset and soft reset but the device wont boot
Any ideas?
Eric
Click to expand...
Click to collapse
You have to instal complte original ROM, the one that came with the phone,
just conect the phone with usb, start upgrading your phone, and wait for 20 minuts to be done
thats how I manage to fix mine 8)
I Removed the Radio 1.06.00!
I had a lot of problems with Messagin. I losed all my internet account/Configuration, my SMS ....
It was a problem with the Radio 1.06.00"

Caller ID

I have a problem with my BA, the name not showing up on my screen along with the number when a call comes in.
Will be waiting for the best solution for it....
only views, no replies
WAKE UP GUYS!
what version roms are you using and have you changed any software since the last time caller id worked
yeah!
before it was windows 2003, later on upgraded to windows mobile 2005. Device information is:
ROM version: 5.03.02 WWE
ROM date: 03/02/05
Radio version: 1.12.00
Protocol version: 1337.42
ExtROM version: -
moreover, my wifi was working before. Now only showing the wireless icon but not starting up. I guess, maybe a driver problem. Please, help me out with this as well
You've probably got the caller's number in your address book twice, so it doesn't know which contact to display?
nope!
nothing is like that afterall, i am also a bit genius actually any other idea regarding wifi, i guess i need a suitable wireless driver for my version. What you guys think
well...first of all...you should upgrade the radio to 1.15.00...pro secundo...there is a fix for caller id on ftp (anyway newest Helmi rom handles with this issue)...then discuss it again...
i think i had the same prob with wifi not sure about caller id ,didnt get any calls and the gps would'nt connect (bluetooth).i looked through the site and upgraded further last friday, (cant find link now will post if i find it)
mine is a 2yr old 02 xda iis PH20b was 2003 now wm5
operator version AKU2.6
ROM version: 5.04.06 WWE
ROM date: 03/02/05
Radio version: 1.13.00
Protocol version: 1337.42
ExtROM version: Helmi v1.1
caller id , wifi & bluetooth all work fine
(added) the only thing i cant seem to set is the lock-out, on 2003 i could set it so after a set time it would log out so the password had to be entered,at the moment i only need the password after a soft reset,
nyuszi said:
well...first of all...you should upgrade the radio to 1.15.00...pro secundo...there is a fix for caller id on ftp (anyway newest Helmi rom handles with this issue)...then discuss it again...
Click to expand...
Click to collapse
dude, where can i get that radio version from, any link?
thank you anyways!
moosethebiker said:
i think i had the same prob with wifi not sure about caller id ,didnt get any calls and the gps would'nt connect (bluetooth).i looked through the site and upgraded further last friday, (cant find link now will post if i find it)
mine is a 2yr old 02 xda iis PH20b was 2003 now wm5
operator version AKU2.6
ROM version: 5.04.06 WWE
ROM date: 03/02/05
Radio version: 1.13.00
Protocol version: 1337.42
ExtROM version: Helmi v1.1
caller id , wifi & bluetooth all work fine
(added) the only thing i cant seem to set is the lock-out, on 2003 i could set it so after a set time it would log out so the password had to be entered,at the moment i only need the password after a soft reset,
Click to expand...
Click to collapse
dude, try to find that link as soon as possible!
regarding your problem, why dont you try going to settings > password and set a password out there!
yeh found the password cheers start/system/lock, now last time i went in i thought that was the only page so i clicked ok and came out this time i re-entered the password then it gave me a second page to change the time.
i found the radio upgrade
http://wiki.xda-developers.com/index.php?pagename=BA_Radio_1.15_Upgrade
and the main page for helmi latest upgrade (wm5)
http://wiki.xda-developers.com/index.php?pagename=HTC_Blueangel_WM5_Home
browse wiki...its useful anyway...
everything was about to run fine suddenly after upgrading Radio Version and Helmi Version, now i neither even access the contacts nor the wifi is working NOW NO UPGRADING! any patch?

WM6: Problem with recieving incoming calls

Since I installed WM6 I can´t recieve incoming calls. The phone lights up but nothing more, and when I click on the reception or phone symbol when it lights up it says "no service" (translated from Swedish).
It was also some problems with Active Sync 4.5 since I upgraded, but those problems might just be because I needed to reinstall it.
Does anybody please know how to fix this, otherwise tomorrow it will go to the repair-shop and I will lose 12 days and the order in my life. : (
The sim-card works on another phone and it worked with WM5, and I have tried hard reset and a reinstall of WM6, but the problem persists.
/Danne
Hi,
Did you try to install an offoicial version of WM6 or one of the cooked ones of this board? If the latter did you take all the necessary precautions first eg installing an upgraded bootloader, etc?
If you have not you may have bricked your phone.
Give us a bit more detail so we can see how we can help.
Cheers
WB
hello
I had the same problem when I upgrade to official WM6 HTC rom, the phone don't ring and I loose the network.
I solve the problem with flashing the radio rom with older version.
I put wm6 on my phone the first day I got it. so I don't really know if this was a problem b4 with wm5.
mine only seems to ring my end after about 8 rings from the dialer so I have to get it within 2 rings b4 voice mail kicks in. Ypu think the if I update the radio as well will that help me?
ps. sorry for hi-jacking your topic seemed along the same line.
the same problem with Bouygues telecom!
Hi guys,
vinzcoyote can you tell me which radio version you put? i'm having the same problem with Bouygues telecom after updrading to WM6
thanks for the help.
C. J.
are you sure the phne settings havnt got blown out?
generally after about a day after i flash on a rom i lose my carrier settigs and i get no connections. i use the cnguar provisioning cab that is floating arond to quickly fix this.
CrunchyGremlin said:
are you sure the phne settings havnt got blown out?
generally after about a day after i flash on a rom i lose my carrier settigs and i get no connections. i use the cnguar provisioning cab that is floating arond to quickly fix this.
Click to expand...
Click to collapse
Sorry but i'm new to this: whats the "cnguar provisioning cab "?
thanks
CJ
Hi everybody,
Sorry it took a while to answer (sleeping time).
I installed the official version from HTC Europe and it it only the incoming calls that doesn´t work, I can call other people.
THE SOLUTIONS
Two solutions seems to have been offered (below) but I (as Curious Jack) are new to this so could you please elaborate of give a link where I can read more?
Vinzcoyote "I solve the problem with flashing the radio rom with older version"
CrunchyGremlin: cnguar provisioning cab
Thanks so far.
//D
Hi there
I had the same problem with mine after flashing to wm6 (but on a trinity)
Apparently there are 2 fixes:
1. Get a NEW sim , or
2. Flash radio rom back to an earlier version that was used with wm5.
Hope this helps
luckydip said:
Hi there
I had the same problem with mine after flashing to wm6 (but on a trinity)
Apparently there are 2 fixes:
1. Get a NEW sim , or
2. Flash radio rom back to an earlier version that was used with wm5.
Hope this helps
Click to expand...
Click to collapse
Thanks!
Two concrete solutions.
One last question: I use a Swedish OS - do the radio roms that is under: "Extracted Radio ROMs for your Hermes" work for me? Or only Anglosaxian PDA:s?
/Dan
similar problem discussed here:
http://forum.xda-developers.com/showthread.php?p=1442269#post1442269
in fact Palm Treo 750 (HTC Cheetah) and Hermes are based on the same radio module.
latest Palm Treo WM6 Radio version: 1.47 (Qualcom)
What that Palm utility does is simply downgrading radio to earlier version. This might work for Hermes in bootloader mode as well.
My point is: no need to install hard sspl if one can downgrade to earlier version of radio with _official_ radio downgrade tool.
I will try later and report back.
update: Palm Radio downgrade tool picked up that device is incompatible. no luck so far.
Seems problem is with Bouygues Telecom
Hi Guys,
Got the exact same problem with Bouygues Telecom. I put a Orange Sim card and it is working so I assume the issue comes from Bouygues Telecom.
So that to check, are the french guys all on Bouygues Telecom or are you using other Telco operators?
Frederic
SOLVED : WM6 & HTC Tytn & Bouygues Telecom now working
Guys,
to make it work, you need to flash ROM Radio 1.38 on top of Windows Mobile 6.
ROM Radio 1.38 can be finded at http://wiki.xda-developers.com/index.php?pagename=Hermes_ExtractedRadioRoms
what version did you use? There are few of them listed on that page:
1.38.00.01
1.38.00.10
1.38.30.10

Categories

Resources