Related
Tried various WM2002 or 2003 ROMs, and settled back on WM2002 as it seems more stable, but I still have a problem where the phone seems to turn off (no green LED blinking), and when you press the top button to turn on the PDA it is as though you have warm reset it. I think I might be missing calls because of this and will have to change the phone if this is the case. Now when I know I might be expecting an important call I have to keep checking the green LED is blinking! I also get periodic SD card erasure unless I write protect it! Overall it is a nightmare to use because of these two issues.
ROM versions:
3.17.03 ENG
ROM date 5/15/03
Radio 4.21.00
Protocol 32S54
Hi mate, my XDA does the same thing - I have upgraded my ROM too (see profile for version etc.). Best thing I can offer to you is that it resets when bumped or knocked (like if I put it down on my desk a bit too hard), the screen will go wierd and then reset. Don't know why this happens but I keep checking my green light for flashing too. My vibrate function no longer works wither. I plan on calling O2 tomorrow to follo up the issues.
Well, I had the same problem with my QTEK 1010, os 2002, until I downloaded a very good clock/alarm software: pTravelAlarm (make a google search for it). among its functions is a very good one which is Chime, (in alarm menu) it wakes up the device each one hour so it will not get stunned. Now I never miss a call. The only disadvantage is that it makes the battery lasts a bit shorter than before.
john banks, there must be something loose in your device, carefully disassemble it and check all screws inside, if all ok, I'm afraid you might have to send it to a repair shop.
after installing the SER 1.2 special version from xda developer, my XDA run smoothly and I can see the sender of SMS anymore
When ever the phone is in standby for a few minutes or so, it refuses to power back on when I press the power button. The only way to bring the phone back is a soft reset. While it is frozen in standby mode it does not receive phones calls, emails or texts. Im running lvsw 03-26. I noticed it didn’t happen with lvsw 3-20…but it was happening with both versions of xda live. I did a few hard resets to see if that will get rid of it…but nothing. I tried searching high and low on the site and even read wiki for answers but no one seems to know what is going on. I saw a few people post up the same issue but still no help….so I decided to open a new thread. Can anyone help?
It happens. Do you have a Storage Card in? If so, take it out for a while and see what happens. What 3rd party apps are you using too. I know Wisbar Advance causes this issue. Can you list what you're running and maybe I can see if you're having the same problem I was.
I've had the same problem with most WM6 roms. Having upgraded to BlackEd2.0 the problem seems to have gone though...
are you running a today plugin off storage card perhaps?
none of the roms i've tried had power on problems
Sometimes you can have that problem with having a cluttered SD Card or having a program that is accessing online in the background.
I have a 512 storage card. I’m not running much 3rd party apps…I have Mundu IM, Microsoft live search, Google maps, WM black commander, macromedia flash player active x…and that’s it. I Had mundu, live search and Google maps installed to my storage card. After reading rabanJR’s post, I uninstalled them from the card and installed them to the phone. I then went back to the card and deleted all program folders and files….I also did a general clean up of the card. Lets see what happens now.
Also to swampy…im not running much of anything on my today screen….just the messages, calendar and the com manager plug in that came with the rom. That’s all. Lets hope for the best.
Bad news, it froze up twice again today. I’m all out of ideas….any more suggestions?
funny thing, that just happened to me today. greed led was flashing, but i couldn't get out of standby mode without soft resetting. maybe some kinda software issue? Its the first time it's happened to me since going to wm6. i did notice it before however.
rzanology said:
Bad news, it froze up twice again today. I’m all out of ideas….any more suggestions?
Click to expand...
Click to collapse
maybe try a hard reset?
What Radio Rom?
Have you flashed a new radio lately? If not, what radio ROM version do you have? I had an issue with my TyTN that was definitely a radio issue. Flashed to 1.38.0.11 and haven't had a single issue with freezing since.
Just an idea, of course.
rzanology said:
Bad news, it froze up twice again today. I’m all out of ideas….any more suggestions?
Click to expand...
Click to collapse
yes sir...i tried many hard resets. A radio upgrade is one of the things i tried...i saw a few people trying it. i went to 1.34 though. im going to flash to 1.38 riiight now! im desperate right now. i'll let you know how it goes.
I had the same problem until I upgraded to black 2.0. I had the radio 1.38.0.11 from the time I upgraded to wm6 and my 8525 was freezing until upgrading to black 2.0 solved my problem.
well i have good news. i upgraded to LVSW(2007/04/08) last night...and so far so good. didnt freeze once today. hope the issue is gone for good. thanks all for the help.
same exact issue here running LVSW 03-26 (goes unresponsive while in standby, green blinking LED, soft reset to recover). 2gb card installed...i'll try removing it to see if freezes go away.
rzanology: if LVSW 04/08 fixes the issue, please post back and let us know!
installed (all to device, not card)
salling clicker
resco explorer/registry/ftp/today
kyphur hold comm button toggle
wmxl apps 8525 keyboard fix
shogun cing
will do...one more note...i updated to 1.38.11 i think it was. what funny is right after i updated the radio the phone froze on the first standby. while i was coming back to post i saw the new rom update for lvsw.
This has a been a long reported problem on WM6 ROMs. 'wont wake from sleep' is the common phrase. Radio and bacground app using net I think was the problem, but no real solution if I remember correctly. On LVSW 3 26 I have gone weeks without this though. In the beginning LVSW 3 26 still did the freeze but after a week it stopped and works pretty good now. Sounds like MS is behind it since it makes no sense at all. LOL.
rzanology said:
When ever the phone is in standby for a few minutes or so, it refuses to power back on when I press the power button. The only way to bring the phone back is a soft reset. While it is frozen in standby mode it does not receive phones calls, emails or texts. Im running lvsw 03-26. I noticed it didn’t happen with lvsw 3-20…but it was happening with both versions of xda live. I did a few hard resets to see if that will get rid of it…but nothing. I tried searching high and low on the site and even read wiki for answers but no one seems to know what is going on. I saw a few people post up the same issue but still no help….so I decided to open a new thread. Can anyone help?
Click to expand...
Click to collapse
Wow, I thought I was crazy becasue nobody mentioned this issue before. I had this problem from day 1.
However, i recently noticed that the 1.38 Radio was eating up my battery life and downgraded to 1.34. This combined with installing Black2.0 seems to have taken care of this problem. I just came back from a weekend away from my phone (which i know is a crime since it is so much fun to use) and it woke up right away.
What Radio do you have?
How long are your phones in standby when it happens?
well....bad news again. even after the new rom update it is still freezing. do you guys think this is hardware? I never froze on wm5...i can't see it being a hardware issue. im almost tempted to call cingular and have them send another one, but i dont know how to go back to wm5. for me, the phone will be in standby for 30 minutes or so....then wont turn back on. any more suggestions?
try disabling everything completely.
1 events and notifications
2 beam auto receive
3 bluetooth
4 wifi
5 put device into flight mode
6 all startup items (including those in rom) move to a temp for now
7 disable activesync
8 disable push email
9 disable all today items
1. disable error reporting customer experience
11 remove anything that reads the sd card
12 remove sd card entirely
13 remove sim card
literally disable everything that runs automatically or otherwise.
power down ur phone by pressing power button for 3 secs. shutdown. leave it for 20secs.
power it back up. then test it now.
if u have a problem now then it could be scary bear notifications fix only. u could have a notification queu problem that is causing ur device to contradicory items simultaneously.
this could be caused activesync so no matter which rom u use it comes back via activesync of calendar or tasks.
if at this stage its fixed then bring things back systematically with the most important first like the sim card. turn off flight mode
c how u go. sometimes pda just gets confused and doesnt wake up from a sleep to well (bit like me in the morning... sometimes bed and sleep is just way to good compared to work/life)...
good luck.
Hi all,
As many of you have heard (or experienced), many Hermes units seem to exhibit less than stable behavior with the production WM5 ROM, or even some of the cool ones here.
Browsing the other forum, we are all to familiar with:
1 - Camera taking black pictures
2 - SD Card not recognized
3 - System hangs
4 - Unit gets very hot and drains battery
5 - Using the alarms is out of the question due to reliability
etc.
After two months of testing, I have two choices:
A - Go back to my Wizard 8125.
B - Move on up to WM6, and see if these issues will be resolved.
My question for those of you have taken the WM6 leap is:
"If you have experienced annoying system hangs, battery drains, and so forth, with WM5, have these issues been resolved when you upgraded to WM6?"
I want so badly to stick with the Hermes, and I'd love to learn all about the various WM6's ROMs... But not if this unit will be as unstable as before.
Any quick thoughts would be appreciated.
I'm ready to hit this forum and the wiki, and learn all there is to know about WM6... but NOT if this unit is still going act up.
I eagerly await your quick replies!
To be honest, I think WM6 is more stable overall compared to WM5 on my 8525.
I also have an 8125, and I have WM6 on that as well. The differences in functionality and the nice new interface are well worth it. The key (in my opinion) is to pick a ROM without all the extra 'garbage' added in, and be careful about the 3rd party apps you add. The core OS is very solid.
Generally speaking WM6 is faster with less hangs.
My only gripe with it is that after you have about 300 sms messages, typing gets slow .... like really delayed ... to solve this i turned the Autospeller thingy off, and it seems to be working flawlessly now!
Compatability is great, it actually just WORKS! .... *cough* most of the time *cough* ... no seriously it rarely hangs, and only the really old applications don't seem to run.
Alarms, christ don't get me started ... i personally just add a calender entry, with the alarm function turned on, it always works and reminds me 15 mins earlier than the desired time
My unit only gets hot while in my pocket a lot or while charging ... i have radio rom 1.41 and the battery life is good, but not as good, i advise 1.40 (for my device it worked best)
SD card not being recognised? never had that problem with WM6
Camera taking black pictures? ... well moving it out into the light generally helps, but out of 300 pictures so far none have been black!
i've also noticed that boot times are slightly quicker
and using IE is MUCH faster and smoother
WM6 is more visually pleasing and is smoother with less hangs. I'm using Sleuth's VARIANT of LVSW ... and its good, i'm an anti-black guy, Black just doesnt do it for me, too unreliable (IMHO!) but well done to JJ for it all, i'm not knocking him, just my personal experience
dropped calls or missed calls are a thing of the past with WM6, i suffered SO MANY during WM5 ... also the lack of OEM images is good, byebye orange customisations horay!! (backup your extended rom 1st, it might be useful later on)
i completely agree with the above statement.
WM6 is great. Haven't had any problems with it. but choose your ROM carefully. I use LVSW, and tried Black Dymond. Both were great, i personally had better luck with LVSW. Radio 1.41 seems to be working well for me, I haven't tried 1.40, so i can't speak to the battery life. make the WM6 jump. you won't be sorry.
WM6 works for me
I had some of the problems you described with WM5 that came with my JASJAM. I have since upgraded to WM6 using the Elf version of LSVW. It works very well for me so far. The only thing to watch out for is that after installing the WM6, it somehow changed the device id and my WebCamera Plus app would not activate anymore. I have to call the Ateksoft to issue me another activation code.
bchau said:
I had some of the problems you described with WM5 that came with my JASJAM. I have since upgraded to WM6 using the Elf version of LSVW. It works very well for me so far. The only thing to watch out for is that after installing the WM6, it somehow changed the device id and my WebCamera Plus app would not activate anymore. I have to call the Ateksoft to issue me another activation code.
Click to expand...
Click to collapse
There's always going to be these small problems with an upgrade, but i think it's still agreed that WM5 < WM6
Hey hey!
These first five posts are VERY encouraging!
I am starting to get excited about it now...!
I'll wait to see who else can offer their opinions.
Thanks guys for the great news!
Michael_514 said:
Hey hey!
These first five posts are VERY encouraging!
I am starting to get excited about it now...!
I'll wait to see who else can offer their opinions.
Thanks guys for the great news!
Click to expand...
Click to collapse
No one elses opinion matters.
My only regret with WM6 is not taking the plunge sooner. See my signature for my configuration.
I am using black dymond 3.5 for past two weeks now and so far it's just rock solid and fast. No hang ups. Quick response to buttons / commands. No drop calls. Smooth operations. Nice visual interface. No complaints what so ever.
My prior cingular rom was stable but too slow and clumsy.
Anybody who is confident in performing upgrade should do it especially as now the risk of bricking the device is very low with Hard SPL 2.10 Olipro.
My 2 cents
Michael_514 said:
Hi all,
A - Go back to my Wizard 8125.
Well, I must say that my experience has been awsome with many of the roms on my 8525 especially JJ's stuff, yes I am a devoted black follower . My experience with the wizard or 8125 was horrible, never modified it at all so i don't know how it does otherwise but I thought it was a piece of ****e.
In conclusion my advice is go wm6 and you will have a new addiction. It is faster, more memory and of course the many other perks like when you get to show your friends that your already runnin wm6 and their stuck with 5
Just follow the steps hard spl, radio then rom and you should be just fine.
I almost forgot, the only times I have experience problems/ instabilities was when I installed things to storage card rather than main memory.
Click to expand...
Click to collapse
I have SoftBank X01HT... I've just upgraded my ppc to Black diamond 3.5 and it works perfect... But I still had the same problem with capturing image in the dark place and it comes up with black picture.. the flash doesn't help at all.. it seems like it's not functional... I hope someone could help me with this... Any Advice? Please feel free to tell me.. I'm waiting.. thanks in advance....
Okay, guys!
I am sold!
I will do my readings; check out the various ROMs, and away I go!
And of course, Hard SPL is a must!
And I agree with the post a few posts back... I am all for a less bloated ROM.
I use my PPC for very specific tasks (Adobe Reader, Outlook, GPS, phone,voice command)... and the less junk/crap/freeware/shareware/malware/utils/bloatware/games I have installed, the better.
I will do some investigating, and I shall take the plunge!!!
Thanks!!!
Michael_514 said:
Hi all,
As many of you have heard (or experienced), many Hermes units seem to exhibit less than stable behavior with the production WM5 ROM, or even some of the cool ones here.
Browsing the other forum, we are all to familiar with:
1 - Camera taking black pictures
2 - SD Card not recognized
3 - System hangs
4 - Unit gets very hot and drains battery
5 - Using the alarms is out of the question due to reliability
etc.
After two months of testing, I have two choices:
A - Go back to my Wizard 8125.
B - Move on up to WM6, and see if these issues will be resolved.
My question for those of you have taken the WM6 leap is:
"If you have experienced annoying system hangs, battery drains, and so forth, with WM5, have these issues been resolved when you upgraded to WM6?"
I want so badly to stick with the Hermes, and I'd love to learn all about the various WM6's ROMs... But not if this unit will be as unstable as before.
Any quick thoughts would be appreciated.
I'm ready to hit this forum and the wiki, and learn all there is to know about WM6... but NOT if this unit is still going act up.
I eagerly await your quick replies!
Click to expand...
Click to collapse
Hi, I have similar problems. I am trying to find out what's going on and the symptoms are like you say: battery drains too fast. Let's say it the battery gets hot, there's something wrong. If you measure the current usage with ACBPowerMeter you will see a high load, like 300-400ma, even with all stuff off, radio off, wifi off, incoming beams off, bt off etc, nada. Now, if you pull out the battery, leave the device the some hours, then start again, power it up, activate GSM and everything, you should be luck and see a current of maybe as low as 30-60ma, even with full brightness on the display. And one time it was okay the whole day, but then all of a sudden, maybe after I hooked up with Activesync or got an SMS, it's gone bananas again.. sigh.. There's gotta be something strange that's completely wrong. I've tried many radios no difference, I've tried bandswitch to limit to GSM only as I live in a area with maybe not super quality 3G signal, did not sort out the problem yet. I had WM6 from LVSW 19-05-2007 with all kinds of radios, then moved on to Pro Black, same problem, but will no try black dymond as someone else mentioned problem was gone with that ROM.
Please all, anyone else with these problems? Any good ideas what this can be? If the device is off for a long time, and I mean off as in battery pulld out, what difference does that make to having the battery off a short while, let's say some minutes? Is there some memory-stuff here? My device is just a week old, never wanted to use a native language WM5 that was in it, hoping this problem will be fixed..
thanks
Update:
I happened to purchase a faulty device!!! There was indeed a HW error on my brand new device so I got it swapped with another one that works. Not all problems are SW-bugs..
I use WM6 on both my 8525's without significant probs; battery drain seems less with radio v.1.38 than 1.40 or greater although use Band Switch to keep phone on GSM when not cruising the net; initial boot up is faster; I've not had overheating probs, no micro SD card issues . Wish I'd gone to WM6 much sooner, but I think having the Cingular 8525 makes a big difference as well.
My battery gets hot and discharges too quick even with radio off. I've tried all radios, am at 1.34 now, will try the 1.43 later tonight if I am able to fully charge battery quick enough... The thing is, if I remove battery for some hours and start over, it's okay, 40ma, radio on etc. Then, at some random point in time, the phone can just lay on the table untouched, it starts consuming battery as crazy, 300-400ma, measured by ACB Power Meter. It's dricing me nuts... I've tried to kill processes, to watch what's going on... I don't have a clue yet, except from there's something "running wild"..
Update:
I happened to purchase a faulty device!!! There was indeed a HW error on my brand new device so I got it swapped with another one that works. Not all problems are SW-bugs..
Hi all!
Okay, I am taking the plunge!
I think I'll stick with Radio 1.40, which I have instealled. Hard SPL is also installed...
...so, the only decision is to figure out which ROM!
I have rounded the choice down to two, based on what I've read.
I'm either gonna go with LSVW or Elf's version of LSVW.
Both are downloaded and sitting on my hard drive, ready to roll.
I just hope I can still use PocketMirror; iGuidance; and spb Pocket Plus.
We shall see!!!!
Any final suggestions are welcome!!!
Thanks!
What have you got to lose?
Just follow MrVanx's guide and enjoy it.
Unwired,
You actually bring up an EXCELLENT question!
"What have I got to lose?"
The simple answer: Time!
As much as I enjoy my hobby that involves tweaking PC's, PocketPCs, laptops, gadgets, and so forth...
...I am an attorney and I do run a business.
This means my time is very important and quite valuable to me.
For every hour I spend tweaking; resintalling apps; customizing e-mail settings; testing the phone; resyncing my business contacts with PocketMirror; researching the proper registry hacks....
...that is an hour I lose making MONEY!
So... As much as I would lllllllove to play with and test single new ROM and its variant, and as much I enjoy spending my day enjoying playing with the latest and greatest operating systems...
It kills me when I can't service clients, and when I can't run my business, because I am busy YET AGAIN(!) resintalling my PocketPC.
That's why I love getting opinions before I move ahead...!
So there ya go... I have no time to lose!
GilesTheAlmighty said:
Generally speaking WM6 is faster with less hangs.
My only gripe with it is that after you have about 300 sms messages, typing gets slow .... like really delayed ... to solve this i turned the Autospeller thingy off, and it seems to be working flawlessly now!
Click to expand...
Click to collapse
Now i have arround 700 sms in the Inbox and about 500 in sent items, and typing works good for me, with autospell on... i keep copy of all SMS i send/receive since i get my first pda, my loved Wizard...
GilesTheAlmighty said:
Alarms, christ don't get me started ... i personally just add a calender entry, with the alarm function turned on, it always works and reminds me 15 mins earlier than the desired time
SD card not being recognised? never had that problem with WM6
Camera taking black pictures? ... well moving it out into the light generally helps, but out of 300 pictures so far none have been black!
i've also noticed that boot times are slightly quicker
and using IE is MUCH faster and smoother
WM6 is more visually pleasing and is smoother with less hangs. I'm using Sleuth's VARIANT of LVSW ... and its good, i'm an anti-black guy, Black just doesnt do it for me, too unreliable (IMHO!) but well done to JJ for it all, i'm not knocking him, just my personal experience
dropped calls or missed calls are a thing of the past with WM6, i suffered SO MANY during WM5 ... also the lack of OEM images is good, byebye orange customisations horay!! (backup your extended rom 1st, it might be useful later on)
Click to expand...
Click to collapse
Really the difference is not only the ROM you use, but what you do with the ROM...this causes ppl talking about one ROM so quick and other ROM so slow, if you take a search, someone (don't remember) make a speed test after HR every ROM, and the results shows the ROMs aren't so different.
Of course if you havn't time for this, this isn't your forum
Regards.
Hi all.
I have recently flashed my Herm to have the fantastic Black MAJIK rom. All went very well and I was pleased with the rom. I did have issues with the wireless not working and also with the blank screen detailed below.
When HTC released the update for WM6 for the TyTn, I decided to flash to that rom and give it a try. Again, works well, although I had to flash back to Radio 1.38 to get the Bluetooth to work properly with my Jabra headset. (I am on Orange in the UK - have not tried 1.43, as could not find it!)
The big problem is this :- randomly (could be 6 hours, could be ten minutes), the phone does not wake up from sleep. The lights are still flashing (I have not tried calling the phone - I will do that next time), but it will not wake up. No ActiveSync at all.
Soft reset is the only viable option.
Does anyone know a fix for this? (Yes, I have roamed through a number of forums and tried the link for 'DisableSyncSchedule', but that did not work.)
I have tried to re-flash the rom a few times, even soft-reset before the HTC stuff installs, stopped GPRS traffic and made sure that the IMAP does not connect. Whatever I do, the problem persists.
I have installed the following: HTC TyTn rom:
- SPB Diary
- SOTI Controller
- mfrazz CommManager
- WMG 3G Video Black Keypad
- GreenBatteryFix
- HTC X-Button
- Pimp my Black
I am loathed to revert to WM5, but if that is the only way foreward, then I might need to.
Any help would be superb!
One other thing
Sorry, meant to say that I am currently running with just the base HTC rom and nothing else installed. Let's see how that goes.
First, The radio should not have anything to do with bluetooth. This is the radio rom for cellular calls, not the BT radio.
BSoD question: Do you have a media card? Have you installed apps on the media card? There have been issues with the media card falling asleep. I had issues in the past installing applicaitons on the card. As make sure that you configure mail NOT to store messages on the media card.
Next....Uninstall all applicaiton that you have installed. Do you still have the problem? IF this fixes the problem, reinstall apps 1 at a time untill you figure out which is causing the problem.
I do have a memory card installed, but no apps are installed from it and the mail attachments are not stored on the card but in the memory. I have recently reset the mobile and have noting installed (not even ext rom) and have only set up mail, sync'd and configured for Orange.
Interesting about the radio having no affect, as it made the Jabra work - no other changes made. (I have re-flashed since then, but still using 1.38 radio rom.)
So I get this all the time, I don't have an SD card - so its not an SD card issue.
I've got 2 Tmobile MDA Vario II's and ever since upgrading from the stock Tmobile rom the phone will hang with a black screen but the message light will blink. If I put the phone in flight mode it never does it.
Its happened on the following roms:
XDA Mobile / Faria's rom
All the Black roms
LVSW
It didn't do it with Tmobile WM5 Rom. Tried various radio updates and it doesn't seem to make any difference. I know Jasjammin mentioned he had seen it but nothing further from him on this.
ITS DRIVING ME NUTS
Some other people must be seeing this also? Please help. When it happens no mails/sms or voice calls so its like the phone is switched off. I too am now looking at downgrading back to WM5
I'm wondering if it might be in the boot loader / rom flasher issue? But I sure I've not done anything others haven't done.
Regards,
Neil.
Bump - nobody else seeing this? Find it hard to believe?!
prophetuser said:
....The big problem is this :- randomly (could be 6 hours, could be ten minutes), the phone does not wake up from sleep. The lights are still flashing (I have not tried calling the phone - I will do that next time), but it will not wake up....
Hi prophetuser
I did notice this issue in the new HTC WM6 ROM (not the dopod one) which you have mentioned. But I flashed my ROM to Black Majik and its cool....I didnt notice this problem.
My device is imate JASJAM. I think the black majik ROM is better, but I noticed one more post in this thread mention all black ROM had the problem as I have not come across it yet.
Maybe the new Black Satin which jasjamming is cooking will not have it and probably you may have to try it, until a new HTC ROM update is leaked I suggest you to use black majik.
Click to expand...
Click to collapse
read my post
100% solution
SOD CAUSE
IN my whole 6 months having my hermes i had never had SOD until i flashed the official dopod rom with matt kitchen. when I traced the source that SOD had came from it was a bad extended rom flash i done. This cause the device to go sleep after the screen time out, and also if i put the phone in idle mode i had to soft reset everytime.
i flashed an original operator t-mobile rom with the extended rom and all my problems went away.
My device has never been quicker no more SOD and battery life is superb with the new radio 1.47 after one whole day with normal use with 3g internet I am still on 70% battery life.
Now I have the perfect device and i think hermes WM6 crave and addiction will be thinned out as there is not much you can do now with the hermes as to wait for PROTON or fully integrated touchflo working ROM.
p.s
TRY FLASHED A AN ORIGINAL OPERATOR ROM WITH THE EXTENDED ROM YOU CAN USE ROMKOCH TO EXTRACT THOSE TWO AND FLASHED YOUR ROM BEFORE FLASHING WM6 AND GUANRANTEE YOU WILL SEE AND FEEL A MUCH MORE RESPONSIVE HERMES. THATS MY 2 cents
duttythroy said:
....i had never had SOD until i flashed the official dopod rom with matt kitchen. ....
What is SOD? please mentione as I am new to the terminologies
Click to expand...
Click to collapse
SOD= Sleep Of Death
Definition of SOD
1. A piece of dirt and grass, usually found stuck to the bottom of shoes after running (Or walking) On a muddy field.
2. Short for "Sodomy", meaning anal sex, which comes from the Sodomites of Sodom. This term, usually used in a derogatory manner, can be used to say **** off, as in "Sod off" or it can be used as an adjective "That sodding bastard"
3. An idiot, a fool. Someone you dislike.
4. S(Screen/Sleep) O(of) D(death) - Blank screen nothing happens..
Examples
Man, all this sod was stuck on the bottom of my shoe, and even worse, it dried out and now it's hard as a rock!
Look at that sodding bastard over there, scoping out girls he doesn't even have a chance with when they're drunk!
F'ing sod spilt my drink, and i wasn't having any of that!
Arghh FFS !! Me blinkin phones crashed again, I soo hate you SOD's.
loool ripdool . nice definitions
duttythroy said:
IN my whole 6 months having my hermes i had never had SOD until i flashed the official dopod rom with matt kitchen. when I traced the source that SOD had came from it was a bad extended rom flash i done. This cause the device to go sleep after the screen time out, and also if i put the phone in idle mode i had to soft reset everytime.
i flashed an original operator t-mobile rom with the extended rom and all my problems went away.
My device has never been quicker no more SOD and battery life is superb with the new radio 1.47 after one whole day with normal use with 3g internet I am still on 70% battery life.
Now I have the perfect device and i think hermes WM6 crave and addiction will be thinned out as there is not much you can do now with the hermes as to wait for PROTON or fully integrated touchflo working ROM.
p.s
TRY FLASHED A AN ORIGINAL OPERATOR ROM WITH THE EXTENDED ROM YOU CAN USE ROMKOCH TO EXTRACT THOSE TWO AND FLASHED YOUR ROM BEFORE FLASHING WM6 AND GUANRANTEE YOU WILL SEE AND FEEL A MUCH MORE RESPONSIVE HERMES. THATS MY 2 cents
Click to expand...
Click to collapse
hi mate, is it possible for you or someone else to give more specific instructions to do this? I am running Sleuths rom which i am v happy with apart from SOD every now and again in the mornings when the phone has not been used for hours whilst i have been sleeping!
thanking you in advance.
yans.
it happen to me several times as i finish a phone call and go back to the Today screen but on the left top corner still display the title "phone".and i cant press it to open the start menu when im at the Today screen not even the start key works.try hold down the power button to shut down but no luck.but everything still works at the Today screen (weather,music plug-in etc)
had to soft reset it.anyone have this problem as well?or is it a radio problem?
iluvgillgill said:
it happen to me several times as i finish a phone call and go back to the Today screen but on the left top corner still display the title "phone".and i cant press it to open the start menu when im at the Today screen not even the start key works.try hold down the power button to shut down but no luck.but everything still works at the Today screen (weather,music plug-in etc)
had to soft reset it.anyone have this problem as well?or is it a radio problem?
Click to expand...
Click to collapse
I use this rom with 1.51 radio till the rom is issued. I never had to soft reset because the rom crashed. The only really annoying issue i had is the bluetooth's one (Time to time, it is impossible to reactivate bluetooth without SR. This is why i do not desactivate it anymore ). We can always argue on choices, taste and colors but this rom is quite stable and fast enough for what i do.
EDIT: BTW check also which applications you have loaded. Did you reinstall a backup done with SPB after coming from another rom? I experienced many problems with that. Even if not pretty, i always reinstall now all my applications after installing a new rom (and i use pimbackup for calendar, contacts,... infos)
I have same problem too, thx
Post in Schaps 3.60 thread...
Not so as you think
I don't agree with that the ROM issue after call. Your deveice may be has some problem. What about bluetooth yes, there is some interesting moment that you select open bluetooth, it doesn't open, as soon as you mark to open you should restart your deveice, then it starts with opened bluetooth. BUt when you are going to turn the bluetooth off there is no problem.
I'm sure, Schap as a great moderator will solve this problems in next generation of his ROMs. The variation 3.60a (has posted), may be 3.60b, then 3.60c may be. Or he will post something interesting like Iphone platform.(I want him to do it)
iluvgillgill said:
it happen to me several times as i finish a phone call and go back to the Today screen but on the left top corner still display the title "phone".and i cant press it to open the start menu when im at the Today screen not even the start key works.try hold down the power button to shut down but no luck.but everything still works at the Today screen (weather,music plug-in etc)
had to soft reset it.anyone have this problem as well?or is it a radio problem?
Click to expand...
Click to collapse
I have the same problem too, what I have discover is that during the call and the screen is off (either it off automatically after a time or you press the power button) then anytime you power on the screen again in between the call or after the call in a short time the problem tiggered.
the only way you can 'fix' it is to wait until call end then off and on your screen once then the 'start menu' back or wait for an amount of time until the phone lock tigger (that one with number pad)
I said 'fix' (with quote) because this definitely a temporary solution to deal with this problem
hope schaps can get more idea in how to trigger the problem and can fix this soon
other than this issue, the rom is really very great
cheers.
To the OP,
If you are using a Hermes I suggest you reflash from scratch ie Schaps ver 3.6 rom, then use radio rom version 1.47.10..
Install ALL your applications from scratch, manually. DO NOT restore from a previous backup using, say SPB Backup; that will screw your installation. Make sure all your apps are the latest versions, capable of running under WM6.
Preferably install one app at a time, as you would anyway, then test the phone and make sure it is working before installing another app, and so on.
Don't install a theme changer or other similar software until you are absolutely sure your installation works. Leave the performance parameter settings as they are, ie at default.
If all else fails use the ROM combination in my signature below. Rock solid installation, no problems or crashes.
Let us know how you get on.
Cheers
WB
have same problem also has anybody found that if you use internet shearing and recive a call you cant hear anyone and phone searches for network
thankz,
jdc21
no crashing for me..
the rom is really stable.
apart from the bluetooth issue its really good..
really stable and fast enough..
works really great for me..
Thanks Schaps for such a great rom.
waiting for 3.60b
Take care that Phone Dialer Skin could cause this kind of problem
wacky.banana Is maybe right
I have Schap's 3.60a along with my trusty Radio 1.47.10
No BT Issue till now
I use BT also with DrYAR-Bluetooth 1.6 (Whoopy!) No Issues at all either starting or Stopping BT
I'm using It for two days now It's OK
Did I mention that this rom Is even FASTER than the previous 3.5x?
i hav the same problem
When did this problem start?
I didnt have the bluetooth turn on just using it normally.and all application i install is fresh onto the phone memory.never install any program on the SD card.about the dialer skin i use Schen Kaiser 3G dialer.
Anyone got fix yet?
Same issue, not just Schap 3.60a
massimo729 said:
When did this problem start?
Click to expand...
Click to collapse
I've had this same issue for weeks now, ever since the newer ROMs have come out for the official releases (i'll have to track back the build numbers). I had it with Sleuth's last release, the vp3G 3.0 release, and now Schap's 3.60. I've done what other posters have said and hard reset, not loaded any apps, and still have the issue.
I believe I have tracked it down to do with X-button, as that's one of the few apps that is installed without customizations in both Sleuth and vp3G (and I run it in Schap 3.60a). My next step is to run vp3G 3.60 lite, without X-button, and see if that really solves my problem.
edwinyuen said:
I've had this same issue for weeks now, ever since the newer ROMs have come out for the official releases (i'll have to track back the build numbers). I had it with Sleuth's last release, the vp3G 3.0 release, and now Schap's 3.60. I've done what other posters have said and hard reset, not loaded any apps, and still have the issue.
I believe I have tracked it down to do with X-button, as that's one of the few apps that is installed without customizations in both Sleuth and vp3G (and I run it in Schap 3.60a). My next step is to run vp3G 3.60 lite, without X-button, and see if that really solves my problem.
Click to expand...
Click to collapse
As a follow-up, I went to VP3G 3.60.1 install, ran the base install with nothing else installed and still had the problem. Still, the workaround suggested by others (putting the phone in standby and coming out) fixes the issue for me.