I figured this out by accident..
I upgraded to windows mobile 2003 SE 2.06 but after I found out that half of the programs (MMS composer, cammera, etc..) dont work, due to incompatibility (error message says they are incompatible) I wanted to downgrade.
I ran the same ROM instalation (2003 SE 2.06) and waited for it to erase my ROM, then I took the phone out of cradle. I was dead at that point. I removed main battery, put it back in. Reboot the phone in bootloader mode (hold down D pad in centre position, then power button and soft reset - all at the same time). Then I put the phone back into the cradle and ran the ROM instalation of my choice. No more problems.
Well, I think using SD card method may be saver.
However, I forgot how to do this.
Cheers,
Darko3 said:
I figured this out by accident..
I upgraded to windows mobile 2003 SE 2.06 but after I found out that half of the programs (MMS composer, cammera, etc..) dont work, due to incompatibility (error message says they are incompatible) I wanted to downgrade.
Click to expand...
Click to collapse
Same thing, I badly need to downgrade to 1.72 or 1.66. I tried it, it did not work. I was was adviced that there is a 1.66 SD version which is safe and possible to apply, any advice where can I find it???
Bty, MTUX 1.4 Ring tone, and other software runs very slow and creats porblems with 2.06!! Beside 2.06 hard reset by itself on weekly basis!!!
Any advice where to find 1.66 SD version?
HELP HELP HELP....
hello people...
i desperately need to downgrade from wm2003se to wm2003. please tell me where can i find my original rom of wm2003. thanx you.
by the way... my ppc is an O2 Xda II.
please do help somebody... its kinda urgent...
Related
Hi
I have just tried to update the rom on my xda exec (downloaded from the o2 microsite) it seems to load fine, but when i do a reboot I just get a wierd green & red speckled screen.
I have tried to update the rom twice now, once when the xda was on, & once from the bootloader screen.
Both times it seems to install correctly, but i get the strange screen.
HELP!!!
Add. My battery seemed to go to about 30% whilst i was updating. Could it be the battery? Can't charge it now to test. Can still get in bootloader screen.
PLEASE HELP!! Thanks
Same Here
I have exactually the same problem!
I downloaded the latest ROM from the My-XDA webiste (O2 Ireland) and it supports the XDA Exec as sold in UK and Ireland.
The upgrade goes fine but when I hard reset it just get a fuzzy screen full of red/green spots (lise interferance on a TV).
Have reinstalled the ROM from another PC and the same thing.
Can access the bootloader (v2.01) with no problem.
Have downloaded the ROM from another PC and tried from there and same thing?
Can anyone help?
Is there a known good ROM file that someone has used to rule out the file, as the XDA was fine until I ran the update.
Please help,
IrishLad
search be4 post
Update
I have tried 2 other ROM's on my XDA Exec and its exactually the same issue.
Once it gets flashed successfully and reboots i get the hazed screen which i cannot use. So its not the ROM file.
Has anyone got help with this, I have searched the posts already and found no solution that it why I have posted this thread.
Please Help,
Thanks,
IrishLad
So its not just me then! Thought I had cocked it up.
If this has already come up in these forums, I cant find it. Please at least send link to the previous problem if it is in here somewhere.
My XDA is dead!
Many thanks for your time & knowledge
Mark
try this one
try this configuration :
O2 XDA EXEC WM6 crossbow
Rom version : 2.02.00 WWE
ROM date : 03/10/07
Radio ROM : 1.15.00
Protocol version : 42.51.P8
ExtROM :UNLOCKED
have fun
the screen is funky but the xda is dead
I too am having this problem and am getting very frustrated.
I have searched the forum for hours and am not getting any closer to a sollution.
If anyone has resolved this problem in the past please send me a private message. I will love you forever if you do.
I had the same problem i think its a dodgy rom on the O2 website
I went into boot mode and used this ROM
http://forum.xda-developers.com/showthread.php?t=297256
Works a treat and is loads better than the normal o2 Rom
Thanks for the feedback
I have tried a few ROM's already with no success.
I will however try the ROM you posted and let you know if it works...
Thanks,
IrishLad
IT WORKED!
Not sure how, or why this worked.
But i installed the Crossbow ROM as listed previous and its working.
And can I just say the Exec is brillant now, its much faster, more responsize and works perfectly.
Thanks for the info, but I had tried 2 different ROM's previously and they never worked let I used one previously with no problems.
Either way I am now staying with Mobile 2006.
Thanks,
IrishLad
ukron is a god
YIPEEEEE!
IT WORKED
Thank you so much
I am very happy. Could you tell?
help
i have the same problem as you guys.
and more i can get my xda exec in to bootloader usb at the top and v2.01 at the bottom
but when i got to update it with the wm6 upgerade mentioned earlier
i get a connection error, please con somee one help
im using vista could this be the problem i have a hdd around some where that has xp on should i try that.
also i dont know is any of you knew but when ur in that messed up screen
if you press the lightbuld button a sort of i guess diagnostics or somthing screen pops up
Enable KITL NO
Clean Registry Hive NO
Formate Storage NO
you can change the no/yes's iv only got the enable kitl to do anything though. change it to yes buy using the buttons by the screen and then the center button it take you to the screen below
Select KITL Transport:
USB KITL
SERIAL KITL
ETHERNET KITL
Select KITL Mode:
ACTIVE
PASSIVE
any help with this will be appreciate
where can we find that crossbow wm6?????is that the one thats needed???
Someone please post a link 4 crossbow wm6 latest
would really b greatful...im it to me, email, or post it either way is good 4 me
THANKS,
Randy
no need problem solved....wm6 crossbow was def. needed
I am very frustrated with my HTC Touch Diamond as I am trying to update it to Hard-SPL yet when it's plugged into the computer (with active sync running) and I follow all the directions very closely, I go to update the phone and it doesn't show any activity on the phone, the progress bar on my computer screen shows 0%, then it eventually pops up with a message saying Error 202. This is a connection error, yet I am positive that the phone is plugged into the computer. Please HELP!
Hello, Did you run SSPL first? You can only flash hard spl when sspl is active it is a black screen.
I have a Telus HTC Touch, does that make a difference on whether or not this will work?
your diamond is cdma. these only work with gsm.
so by the word 'these' in the last post, you mean that the Rom updates won't work?
I don't think SPL has to do anything with CDMA or GSM. Some ROMs have an option in the phone settings to choose either GSM or CDMA.
ryanseyz: Make sure you have a factory ROM ready before trying the cooked ones here so when things happen unexpectedly, you always have a choice. Next, there are 2 versions of SPL here, try both. Make sure you install EnableRAPI.cab and CertSPCS.cab installed on your device.
Regards,
Carty..
anyone has a solution for this yet? I'm experiancing the same problem with my Touch Pro, can't seem to get it to work.
I installed both files like mentioned above but still give error 202.
The funny thing is it does recognize the current version of my rom (stock).
Greetings,
Phyrax
Phyrax said:
anyone has a solution for this yet? I'm experiancing the same problem with my Touch Pro, can't seem to get it to work.
I installed both files like mentioned above but still give error 202.
The funny thing is it does recognize the current version of my rom (stock).
Greetings,
Phyrax
Click to expand...
Click to collapse
The same here with my mda compact iv. I've tried all versions of the RUU of hardSPL with no result (error 202). When I update the official rom of t-mobile (1.93) with the RUU, there isn't a connection problem and everything goes well.
My device is not simlocked, but i suspect it has a security lock or something like that.
Hello, I have the same problem with a HTC Diamond : error 202 and everything is connected, hotsynched, etc.
Did anyone find a solution ?
anyone??? im having the same problem..
I'm having this issue as well, any solutions?
The same problem
I have a HTC Touch Diamond and have the same problem.
I don't know what i have to do to fix this problem.
I have got the same problem. Add I have problem with align screen, so I can't run any cab on device. Looking for any advice..
i have a htc mda basic ....same problem...any solution...please help....
I'm not sure, but if i'm not wrong i had the same 202 error code last time i tried to reflash original (stock) spl, for warranty reasons. I solved the problem flashing stock spl (from hspl 1.93 olinex) with the phone conencted to activesync: run sspl-manual.exe from the device (previously copy sspl-manual on the device): the phone will go to black screen; than run the normal romupdateutility.exe from pc, and follow ordinary instructions.
Hope this could help.
Dudubai said:
I'm not sure, but if i'm not wrong i had the same 202 error code last time i tried to reflash original (stock) spl, for warranty reasons. I solved the problem flashing stock spl (from hspl 1.93 olinex) with the phone conencted to activesync: run sspl-manual.exe from the device (previously copy sspl-manual on the device): the phone will go to black screen; than run the normal romupdateutility.exe from pc, and follow ordinary instructions.
Hope this could help.
Click to expand...
Click to collapse
Thank's..., this solution work for me...!!!
For me too !!! working now !
Thanks it work!
Thanks !!! It works !!!
I recently I upgraded my HTC Touch Diamond ROM to 1.93 by unlocking the device. I also formatted everything when installing the new OS. After that, I no longer cannot run mapking. I received "We're sorry...a problem has occured ith manila.exe" message and mapking crush....
Can any body help me the solution ???
wunna said:
I recently I upgraded my HTC Touch Diamond ROM to 1.93 by unlocking the device. I also formatted everything when installing the new OS. After that, I no longer cannot run mapking. I received "We're sorry...a problem has occured ith manila.exe" message and mapking crush....
Can any body help me the solution ???
Click to expand...
Click to collapse
Try performing a hard reset and report back.
Also, please tell us more about your device.
ps - hard reset: hold volUP and the center button while pressing reset. you should get a gray screen with 2 options. Press volUP again at this point. When it's done, it will tell you to press volUP to reboot.
What Information I need to provide ? I am now in Malaysia and bought from S'Pore phone shop. I think my phone warranty is only for SG.
I cannot download ROM Upgrade version from HTC. The message .."sorry. this software...." was displayed. Then, I used CID Unlocker to upgrade my ROM...
Actually, my Mapking was running in last version of ROM. It just happened after upgrade to 1.93.
What else i need to provide ?
Hi,
I just did the Hard reset as what you mentioned. Still got the same thing.
Rgds
Hi All,
Now OK. I just FORMAT again my internal storeage with FAT32 format.
Thanks..
Are you using stock rom (ie. from HTC) or cooked ROM from this web site?
I am using Dutty's ROM with PAPAGO R12 which is the equivalent version of Mapking R7 (i think). I have no problem with PAPAGO R12.
formatting the internal storage with fat32
I had the same problem, how do i format the internal storage with fat32? i can't find the format option.
Hello everyone, I am really new to this forum having received the Dash 2 days ago. Looking to get it up to speed I flashed the 6.5 Energy Rom according to instructions. I think that was a very bad move, because now the cellphone is stuck on the Loading Energy Rom screen. I have searched the forum for answer and have already tried the following:
1- Entering bootloader and flashing original ROM. No luck because EVERY rom I have gotten, be it from here and T-Mobile, it says invalid vendor ID.
2-Tried to perform a hard reset. Did not work.
3-Flash the original ROM through the memory card. No avail.
The phone cannot connect to active sync, so I can't install any cooked ROMS. I think the solution is installing the original ROM by the bootloader, but I cant seem to find a compatible one. My cell information is the following:
Bootloader screen info: ONBL 1.22.0000 SPL 1.22.0000 IU
EXCA 100 S/N SZ713FE05873.
Is there any way with that information someone can tell me which ROM to use? Or any other tip/hint/suggestion? Any help will be greatly appreciated!
I have the same Bootloader screen info: ONBL 1.22.0000 SPL 1.22.0000 IU value and i was able to restore my phone to working status with the following ROM
http://www.megaupload.com/?d=IJIVTIMF
Hope this help
10507
Thank you very much 10507! I'll download it now and see if it works.
Thanks for the file but it appears that it is for the SDA. It dit not work
luisro said:
Thanks for the file but it appears that it is for the SDA. It dit not work
Click to expand...
Click to collapse
That's odd, I was able to restore my Excalibur/Dash after flashing the corrupted EnergyRom.
Hope you will find a way to resolve your problem.
10507
But how did you do it? Flashing it through USB or through the memory card? The weird thing is that when I run the EXE the cellphone that appears in the picture of the program is an SDA. But well I will try it again and thank you for the help!
I used bootloader method and connected my phone through USB for flashing. Remember to remove your memory card when flashing.
well, I've been in your situation for almost 3 days now, and still no solution for it, maybe it's time to put it in the box and purchase a new one , all thanks to the broken EnergyROM ...
Ok guys. Don't give up. Believe it or not, a Dash is NOT easy to brick like some other devices. the steps are fairly clear but let me refresh:
- Go into bootloader by holding the camera button and powering on the phone
- Connect the USB cable, you will hear the ba-bing USB connect sound on your PC (if u don't thats why you're having issues flashing)
- Download and unpack a "factory sealed" signed ROM. I use this one: http://rapidshare.com/files/7886560...S_1.33.422.1_4.1.13.51_03.07.90_Ship.exe.html
- With USB connected and the phone in the multicolor bootloader, run RomUpdateUtility.exe, check the boxes, it next, bla bla bla.
- It will look for your device for 20 seconds. then hit "update" and next.
- It should then start flashing the Excalibur Brightpoint Factory ROM back onto your phone
- If you can't get this far or it fails, try a different PC or Flash from the SDcard
** NOTE: If flashing from USB, REMOVE the SD CARD! This is the biggest mistake of most people trying to flash from USB.
Good luck.
ookba said:
Ok guys. Don't give up. Believe it or not, a Dash is NOT easy to brick like some other devices. the steps are fairly clear but let me refresh:
- Go into bootloader by holding the camera button and powering on the phone
- Connect the USB cable, you will hear the ba-bing USB connect sound on your PC (if u don't thats why you're having issues flashing)
- Download and unpack a "factory sealed" signed ROM. I use this one: http://rapidshare.com/files/7886560...S_1.33.422.1_4.1.13.51_03.07.90_Ship.exe.html
- With USB connected and the phone in the multicolor bootloader, run RomUpdateUtility.exe, check the boxes, it next, bla bla bla.
- It will look for your device for 20 seconds. then hit "update" and next.
- It should then start flashing the Excalibur Brightpoint Factory ROM back onto your phone
- If you can't get this far or it fails, try a different PC or Flash from the SDcard
** NOTE: If flashing from USB, REMOVE the SD CARD! This is the biggest mistake of most people trying to flash from USB.
Good luck.
Click to expand...
Click to collapse
Thanks ookba for cheering us up. I'm having the same problem like many, many people in this forum hopeless seeing our dash not responding to every solution proposed in this forum and the only thing that we have right now is keep trying to flash and see if it works. I will try again in different PC and see what happens. I'll let all of you know if I finally resurrect my s621.
Thanks everyone for all the help! It's hard to find people that are so helpful on internet forums. I'm still in the same situation as gmaniac and alexalexoe but hopefully we can find something that will fix our problems
luisro said:
Thanks everyone for all the help! It's hard to find people that are so helpful on internet forums. I'm still in the same situation as gmaniac and alexalexoe but hopefully we can find something that will fix our problems
Click to expand...
Click to collapse
This problem is ridiculously weird to why some members are able to restore their phone to original factory condition, and others are not able. Therefore, I have search from trustworthy sites and from friends for difference made ROM. Hopefully, one of these ROMs with help out anyone...........
1.33.422.1 (Worldwide English, WM6)
http://rapidshare.com/files/7886560...S_1.33.422.1_4.1.13.51_03.07.90_Ship.exe.html
1.27.405.1 (Worldwide English, WM6)
http://rapidshare.com/files/100235639/HTC_S620_WWE_1.27.405.1.exe
1.22.531.6 (T-Mobile USA, WM6)
http://www.mediafire.com/download.php?z4vjgzxisrz
1.22.531.4 (T-Mobile USA, WM6)
http://www.mediafire.com/download.php?yygkw1d5xmc
1.11.531.1 (T-Mobile USA, WM5)
http://rapidshare.com/files/104641948/T-Mobile_DASH_WM5_V_1.11.531.1.exe.html
Excalibur_BRIGHTSTAR_PTB_1.30.514.2_4.1.13.47_ 02.98.90_Ship
http://www.mediafire.com/?9gbwdzd2omg
Thanks 105507 but no success at all, I even found 2 more factory roms in the web and also they don't work. I own an unbranded international version s621 manufactured by Brightstar corporation (I tried to flash Brightstar's stock rom but it didn't work) and I noticed this because in the warranty docs it says brigthstar corporation and originally the phone came with WM5.
not that this will help. but this is one of the reasons why people should be really installing the hardspl so if you have a bad flash, you dont have to install a stock rom. any rom whether be it cooked or not will work. but this hardspl must be done prior to installing ANY rom. the hard spl is done by jockyw2001. send him a pm to see if theres anyway to get that on the phone, even in its current state.
edit: here's the link to the hardspl: http://forum.xda-developers.com/showthread.php?t=329605
luisro said:
Hello everyone, I am really new to this forum having received the Dash 2 days ago. Looking to get it up to speed I flashed the 6.5 Energy Rom according to instructions. I think that was a very bad move, because now the cellphone is stuck on the Loading Energy Rom screen. I have searched the forum for answer and have already tried the following:
1- Entering bootloader and flashing original ROM. No luck because EVERY rom I have gotten, be it from here and T-Mobile, it says invalid vendor ID.
2-Tried to perform a hard reset. Did not work.
3-Flash the original ROM through the memory card. No avail.
The phone cannot connect to active sync, so I can't install any cooked ROMS. I think the solution is installing the original ROM by the bootloader, but I cant seem to find a compatible one. My cell information is the following:
Bootloader screen info: ONBL 1.22.0000 SPL 1.22.0000 IU
EXCA 100 S/N SZ713FE05873.
Is there any way with that information someone can tell me which ROM to use? Or any other tip/hint/suggestion? Any help will be greatly appreciated!
Click to expand...
Click to collapse
My phone is the same your phone but ONBL 1.33.0000 and SPL 1.33.0000
I'm trying to find the original rom of this line but not found. Please help me!
Have you done a reset? My friend fixed his by trying reset a few times. He reset it, walked away...., it took long time to see whether it booted over; if not, do it again...
By the way, he leave the sim card in; and, you need to remove your micro sd card.
On an official site it is possible download ROM for your phone. It is flashing from bootloder mode. It some times helped me, while I have not flashed hard SPL.
luisro said:
Thanks everyone for all the help! It's hard to find people that are so helpful on internet forums. I'm still in the same situation as gmaniac and alexalexoe but hopefully we can find something that will fix our problems
Click to expand...
Click to collapse
Hi my friend, I wish you lucky!!!
by the way, where country you're from, I have some Shipped Roms here for brazilian Excalibur (S621), maybe it could help, if the answer is yes, let me know to made this one come to you
http://wiki.xda-developers.com/index.php?pagename=Elf_GoldCard
Furious Girlfriend (oh My beloved Helloween died with my ROM's)
Boy oh Boy...
My ROM's are now in heaven
Girlfriend deleted they (I'm so sorry...)
But, pay attention in this thread
http://forum.xda-developers.com/showthread.php?t=381726
In there have a sort of shipped ROM's and maybe coud help you
Good luck my friends
A friend from XDA have some Shipped Rom's and will upload it for you, shortly he'll post something here
I downloaded Rhodium-HardSPL_V2_00R3_185HSPL.zip and unzipped but i cant perform hard spl using this.. it says error[246] device not responding.. it is not allowing me to perform both the automatic and manual hspl.. even i hard reset my mobile before performing HSPL.. I am in UK using Tmobile Touch Pro2 ROM version 1.86.401.0 (67102)WWE; Radio Version 4.49.25.17.. Please anyone help me to perform HSPL and install the Cooked rom...
Edit/Delete Message
Is your phone service on? It can't perform HSPL if it isn't on.
You might want to check that your phone is synced to Windows on your computer.
Vista needs Windows Mobile Device Center installed to sync I believe.
Had lots of issues doing the same thing to my Tilt2.
Here is what I did. I deleted any partnership in Activesync (probably did nothing but did not hurt)
downloaded enablerapinew.cab and installed it on memory card
did a hard Reset (actually 2 but hey who knows)
Moved enablerapinew to phone, removed SD card and ran enablerapinew.cab let phone sync with whatever name it wanted.
Once synced I ran the installer in automatic and it worked.
I spent 4 days trying everything so there is hope.
Thank u INRBigness i removed my Memory card and it works... Thank u very much
flashing touch pro 2
i have tried every trick in the book to get the hard spl on my touch pro2 from sprint. i am ready to give up and just suffer with the stock rom. please help!
As the OP's device is in this shape in his other thread here it's no wonder the HardSPL is not working.