MAYDAY MAY DAY HELP - Upgrading, Modifying and Unlocking

I THOUGHT I WOULD UPGRADE MY ROM TO 1.72 BUT IT WAS 19% THROUGH AND CAME UP WITH AN ERROR
IT SAID ABOUT RESTARTING NOW MY PHONE WONT SWITCH ON JUST GOT 02 SCREEN WITH ROM DOWN BOTTOM
WONT ACTIVE SYNC OR CONNECT WITH CRADLE
IS IT F*****

Try resetting the device, placing it back in the cradle and re-running the upgrade. It doesn't require ActiveSync as the upgrade process looks after its own connection.
Make sure the cradle is connected directly into a USB port on your PC and not to a hub. Also make sure the power supply is connected to the cradle.

Related

Can`t sync my BA by activesync

I`ve been trying to solve this and found nothing about this problem.
I was able to sync my Blue Angel with my pc and laptop but it all of a sudden stopped to sync. It tries to connect but then it says that there is a problem with the connection. I have Wm5 installed 5.04.10 WWE.
It started to happen both in my laptop and pc, So I assume that it is all because of the phone or craddle. I tried cold reset and still get the same problem.
Please I need help...
Thank you in advance...
BitDefender???
http://forum.bitdefender.com/index.php?showtopic=109&pid=1044&st=0&#entry1044
I've got the same issue and I'm blaming it on my sync cable going bad.
I tried plugging the phone into a machine that had never seen my phone before and got the same error, but I can sync via bluetooth. Hard resetting the phone didn't fix it either.
I've noticed that when this happens, the phone will show that it is charging, but in reality does not.
Also, the wall charger charges the battery normally.
So, once I get a new cable, I'll know if it is the cable or the phone itself.
I'd try for a cable, it's the cheapest fix.

pc doesn't detect usb connection/sync

Hi,
I bought an used Dash and when I try to sync it through ActiveSync nothing happens. I tried to intiate the sync from the Dash and nothing happens either.
Basically, nothing happens when I connect it to the USB port in the PC. It doesn't try to sync, the PC doesn't see a new unit or anything else that happens when you connect something to the USB. I used to have another Dash sync'd to the same computer and everything was fine.
Is it possible that the usb port in this Dash is broken? is there any way to verify it? I've tried with two different cables that I know they work and plugging it in different USB ports in the PC.
Thanks.
= J =
PD: the Dash does charge through the usb cable. And after charging for a bit, I can see that the battery is full, led is green.
profitoral said:
Hi,
I bought an used Dash and when I try to sync it through ActiveSync nothing happens. I tried to intiate the sync from the Dash and nothing happens either.
Basically, nothing happens when I connect it to the USB port in the PC. It doesn't try to sync, the PC doesn't see a new unit or anything else that happens when you connect something to the USB. I used to have another Dash sync'd to the same computer and everything was fine.
Is it possible that the usb port in this Dash is broken? is there any way to verify it? I've tried with two different cables that I know they work and plugging it in different USB ports in the PC.
Thanks.
= J =
PD: the Dash does charge through the usb cable. And after charging for a bit, I can see that the battery is full, led is green.
Click to expand...
Click to collapse
Check this:
on the dash
Start menu
Settings
Connections
More
USB to PC
remove the check-box in the advanced connection setting
save and try again
also... are you running a firewall? if so, that's quite likely a problem as well. i run comodo and it blocks the connection. i haven't figured out the proper setting yet to allow the phone through so i just shut comodo off when i'm needing to access the phone from my computer.
When you plug your usb cable into your phone, does the light on the top turn either amber or green? If so, usb connection is working. If it is still not syncing, open Activesync on your PC got to tools-connectionsettings and make sure Allow usb connections is checked.

USB connection not working.

My TP2 (vodafone) has decided it doesn't want to connect via USB any more. I have tried different USB leads, and verified it's not that by using other devices. I've tried different USB ports on my desktop (Windows 7 RC 7100) and also tried my laptop (XP) neither of which want to connect.
I've checked the USB to PC section in settings and tried it as both Activesync and disk drive, and with and without the 'enable faster data synchronization' box ticked, and soft reset after changing each setting. but every time the computer just won't recognise that I have plugged a USB device in.
Any suggestions?
No one have any ideas on this? I've tried a hard reset now in desperation, and it still doesn't seem to work.
PC does not recognize TP2 connection
Same problem for me; the TP2 is not recognized by the PC (or laptop)
Is there no program to check this? Otherwise.......I have to send for warranty repair.
Anybody any idea??
I have the same problem.
I can't get the device to connect to my PC by USB. It charges through the PC USB lead though.
What did you end up doing? Is it time to make a warranty claim?
I'm not sure if it applies to your situation, but for the longest time I could not get my Kaiser to sync with my laptop (which I usually kept wifi off on).
Turns out ActiveSync was out of date and didn't work since I had upgraded to WM6.1. If you're up to date already that probably doesn't help, but I thought I'd toss it out there.
just to let you know, i returned my tp2 to vodafone and the replaced it. the new one worked fine as soon as i plugged it in to the usb. so that proved it had to be a hardware fault.

ATT Tilt 2 won't recognize computers all of a sudden

I have an ATT Tilt 2, and I've gone through roms like candy, and I still use the original USB cord that it had came with phone.
So I just bought a new computer a week ago, and ever since I can't seem to sync my phone up to my computer via usb cord (Bluetooth works fine). Now normally there's the steps to find the drivers, make sure active sync is enabled, make sure that small checkbox is checked or not. Data connection is enabled/disabled. Prompt when its connected to the comp, etcetc.
The problem is, the phone doesn't recognize that it's plugged into the computer, and just treats it as a power source. I've done some reading, and found there's a program that lets you trick it into thinking USB ports are power sources (fast charge or whatever) but I haven't downloaded nor install it.
Currently I'm running an EnergyRom rom, and I can't update it or change it.
I used to upgrade the rom every time NRG came out with an update, so I'm baffled to why all of a sudden it won't work.
Edit: I've tried connecting it to several computers, does the same thing. It won't realize it's connected to a computer.
Usually, if I pop out the battery, hit the power button a few times, then start it back, up... it will go back to working. The only times I ever seem to have this problem you are describing though is when I switch from active sync to "usb" (where it only looks at the storage card) and then when I switch back to active sync next time I plug it into a PC, it will not connect.
you should try to reinstall the activesync if you use xp.. hope itd help..
regards..
Winlockwood said:
I have an ATT Tilt 2, and I've gone through roms like candy, and I still use the original USB cord that it had came with phone.
So I just bought a new computer a week ago, and ever since I can't seem to sync my phone up to my computer via usb cord (Bluetooth works fine). Now normally there's the steps to find the drivers, make sure active sync is enabled, make sure that small checkbox is checked or not. Data connection is enabled/disabled. Prompt when its connected to the comp, etcetc.
The problem is, the phone doesn't recognize that it's plugged into the computer, and just treats it as a power source. I've done some reading, and found there's a program that lets you trick it into thinking USB ports are power sources (fast charge or whatever) but I haven't downloaded nor install it.
Currently I'm running an EnergyRom rom, and I can't update it or change it.
I used to upgrade the rom every time NRG came out with an update, so I'm baffled to why all of a sudden it won't work.
Edit: I've tried connecting it to several computers, does the same thing. It won't realize it's connected to a computer.
Click to expand...
Click to collapse
Look at your notificaitons queue and make sure the replog.exe notifications are present

[Q] usb n computer doesnt sync but charges

Like it says, my computer charges it but doesnt sync up with my computer. i have a touch pro 2. (tmobile version) Im trying to connect it to my computer so i can do an upgrade for the energy rom any body else have this problem?
IF so can you help me on fixing this situatioN? please!!? thanks a bunch guys
happy holidays
I know this problem to good -I guess a hardware fault. I had this with my first and now with the second TP2 too.
For my guess the USB connector-hole (or how you call it in english) is too big! If I place the TP2 in a dockings station everything is fine -sync no problem.
If I try it with only connection by cable -not a hope.
If you buy I docking station I guess the problem could be solved
I had this with my 1st Tilt 2, nothing I tried worked. I had to sync/move files via BT USB. It was inexpensive (made by ASUS) at $14 and very low profile. Believe it or not, it worked really well, even for huge RHODIMG files when I wanted to flash a new ROM. The bigger the file, the longer it took, but it *did* work.
Recently, I got a great deal on a used, mint condition, Tilt 2 with lots of accessories, including an Otterbox, for $150 shipped, and my USB syncing is working again. Definitely a better deal than the $90-$275 estimate HTC gave me to repair the USB.
Hope you get it sorted, but it's been a common problem with this phone. Seems the pins inside are really delicate.
EDIT: Hey I just noticed we all have a "thanks meters" now... Schweet!
Debbie
dang is there any other way i can fix thiss??
Just had my T-MO Vario V replaced for this very thing. As my replacement started acting up as well with the same error, I searched again on the web and found that it might also be a faulty usb cable or the fact that you connect your phone via a hub rather than directly to a mainboard port.
I use another cable now connected to a mainboard port and guess what (and keep your fingers crossed) for the moment it's working.
Good luck!
Robert
Im using a T-mobile (SIM Unlocked) TP2 from Singapore. Same thing here, when plugged to the PC via USB (the one that came with the phone) it charges but doesnt show the actual syncing with ActiveSync 4.5. I used to have an old Treo 750 that synced just fine (though TP2 definitely has a much much better PC connector than the Treo).
One thing I noticed is even though ActiveSync is not popping up for automatic syncing, It always show in the taskbar as connected. I can even navigate to my TP2 in Explorer & transfer files to & from my PC via USB. My question is, is there a way for ActiveSync window to really come up whenever I plug my TP2 in?
nelvbautista said:
. My question is, is there a way for ActiveSync window to really come up whenever I plug my TP2 in?
Click to expand...
Click to collapse
Yes it is in the device setting in active sync ...
I also tried every possible settings with Activesync options in the phone but it still doesn't show the actual ActiveSync window when I plug my TP2 via USB though it connects & via the taskbar icon & still explorable in windows explorer. I just want to have that peace of mind that I can fully back up using Activesync aside from using other 3rd party backup tools before I start playing with different ROMs out there.
first check the "usb to PC" settings in setting menu on the phone, try unchecking "enable faster data sync" see if this makes a difference .
if not then try going into your control panel on your computer, and use "add and remove programs" and remove active sync , then re-install it , also change the usb cable if you have another one laying around..something that will make a difference..
"enable faster data sync" uncheck this and it should works.
I had same problem...
Try entering bootloader mode and plug it in and see if windows detects the device if it does then try clicking on start on your PC, then right click on my computer, then click manage.
When computer management opens click on device manager then click the + to the left of usb devices.
click on each usb controller you find and press delete and uninstall each one until none are left. Then restart the pc and unplug the phone, soft reset the phone. Wait until windows restarts and AFTER it has finished installing ALL drivers for your usb controllers plug the phone back in and see if that fixes the problem.
I just thought as well, try plugging the usb lead into a different usb port, that way windows will treat the phone as a new device

Categories

Resources