HELP PLEASE!!!! Error 008: Open Port Error - Upgrading, Modifying and Unlocking

I have just tried to update my XDA to the Special Edition ROM. When I ran the program it got to Step 4 Upgrading ROM image and tehn came back with:
Error 008: Open Port Error
Can not open a COM/USB Port. Please use Device Manager on PC to make sure that the COM/USB port is available and working properly.
Have to click on OK at which point the program just closes.
Rerun the program and it comes up with an error:
Apapt ROM
Please connect your XDA to ActiveSync
Doesn't do anything on Retry. Have to Cancel.
Cancelling brings up Step 4. Upgrading Screen and the Error 008: Open Port Error again.
I'm stuck in a loop.
The XDA won't do anything now - it is stuck on the Upgrading Screen.
HELP PLEASE!! I'm dead in the water here ....

Related

ERROR 120, country id error. With USB v1.00 on my screen

Hi,
I tried to upgrade my MDAc with the rom from TMobile.
During the upgrade my computer asked for this file "wceusbsh.sys".
At that point the upgrade stopped.
No i only see "USB" and "v1.00" on my screen.
The charger led is red.
When trying to upgrade again, i get ether this message:
Error 120, country id error
or
err no device
I located the file "wceusbsh.sys" but still.
After "checking the information on your device" i get the error.
"Error 120, country id error"
How can i solve this problem.
Greg
You're stuck in bootloader. Did you try to upgrade to an other language?
You can try to hard-reset your device 'power & soft-reset' at the same time to boot your magician.
If it doesn't boot, kick it back in bootloader 'camera & power & soft-reset' at the same time for several seconds, till screen turns black & read 'serial v1.00'. When connected to usb it reads 'usb v1.00'
Now get maupgradeut_noid.exe from the ftp. Unzip your shipped-rom file you downloaded from TMO. Put the maupgradeut_noid.exe in the same folder as the unzipped files like maupgradeut.exe, enterbl.exe etc. Then execute maupgradeut_noid.exe instead of maupgradeut.exe this will give the error 120 once more. Just exit & execute it again, now it should proceed upgrading.
Cheers, M
=(
Same problem! Trying to use no id upgrade . I hope it will solve my problem.
P.S. DO NOT upgrade ROM when batt is lo =)

ERROR [260] After upgrading wtih the "official" wm6

I upgraded my 85' with the "official" wm6 rom and now I cannot go to other roms. The process was solid, meaning I was fully charged, no power loss, and it was synced. I've tried every version of rom available and get the same results. I went through the "brick" thread and I'm affraid I don't quite fit into any category. I can get phone calls and everything works, I just happen to like all of the great ROM's everybody is cooking and want to try them to see which one I favor. I tried using the Hard-SPL and all of the other bootloaders out there and I always get that ERROR [206]. I've tried to restart the machine, and hard reset the 85'. Any good idea's.... Maybe I need to search more? I'll try that.
==============================================================================
UPDATE:
What I should really do is rent a gun, and buy a bullet...
I'm not saying I'm some sort of season veteran of flashing... but I've never had to touch anything after I accept all terms. For some reason, when it came down to the last "Next" form, my phone flashes "Accept" super fast. So what to do?... I push "Yes" soft key fast as I can and it runs like grease lightening... I had to choose SS for the boot loader because it couldn't figure it out... Maybe next time around.
Have you tried to flash a coocked ROM using the microSD card?
Hi,
did you try get your phone in the tri color bootloader screen and then running the Hard SPL program again?
I did not try to do flash it woth the MicroSD card... I just found out that I could flash it with the MicroSD card about 2 seconds ago. And I wanted to Hard-SPL at the tri-color as a last result in fear of bricking but everything is okay now. As I said before, I've never had to touch my 85' while flashing the rom, it just did it on it's own, but that "official" rom was not about being neglected. And then when I saw it flash something and say "yes", I pushed it and never looked back. It's alllllllllllllllllll good.
I do have one question, is the SSPL preferred over the other choices? Or is there one that is recommended?
Hi joshkrajnak,
How did you solve this problem exactly cos I dont understand what your saying:
http://forum.xda-developers.com/showthread.php?t=298640
boz said:
I extracted these error codes from a Hermes rom upgrade 'read me' document, these should be of help if you get an error message during a rom upgrade. They should be common to all roms, please correct me if I am wrong.
ERROR [202, 204] : CONNECTION
This error message will appear when the device is not connected to ActiveSync correctly. Make sure you properly connect the device to the PC through ActiveSync before running RUU.
ERROR [260] : CONNECTION
This error occurs when there is an “open port error” before upgrading the CE ROM image.
Solution: You can reset the device and run RUU again. If you still encounter an “OPEN PORT ERROR” again, reset your computer and try again.
ERROR [206] : MEMORY ALLOCATION
ERROR [280] : UPDATE ERROR
When you see any of these error messages, close other running programs on the computer and run RUU again.
ERROR [208] : FILE OPEN
ERROR [210] : FILE READ
These error messages indicate that RUU lacks certain important files and cannot continue with the update. Please get the complete RUU package again.
ERROR [212] : FILE CREATE
ERROR [214] : FILE WRITE
ERROR [222, 224] : DEVICE NOT RESPONDING
These error messages will appear when remote access control has failed. Check the ActiveSync connection and try running RUU again.
ERROR [220] : MAIN BATTERY POWER
This error message will appear when the device’s battery power is not sufficient. Although RUU will instruct you to plug in the AC adapter, it still has to make sure that your device has enough power to upgrade the radio. (Even when you plug in the AC adapter, the device is unable to charge the battery when it is upgrading the radio).
ERROR [238] : FILE READ
This error message may appear when, for some unknown reason, the ROM image on the Mobile Device is corrupt. Download the whole RUU and try again.
ERROR [240] : FILE OPEN
When this error message appears, check whether the downloaded image is placed in the directory of RUU. If, for some unknown reason, you find that the ROM image is not located in the RUU folder, you have to download the RUU and retry again.
ERROR [242] : INVALID LANGUAGE
ERROR [244] : INVALID MODEL ID
ERROR [294] : INVALID VENDER ID
ERROR [296] : UPGRADE ONLY
One of these error messages will appear when you use the wrong RUU to do the upgrade. RUU will check if the Model ID and Language ID are compatible with the device. Make sure you use the appropriate RUU tool to upgrade.
ERROR [246] : DEVICE NOT RESPONDING
This error message indicates that RUU cannot start the update process. Please contact your service provider for assistance.
ERROR [262, 276, 284, 302] : UPDATE ERROR
This error occurs during the CE ROM code upgrade process.
Solution: If this happens, you can just soft-reset the device and run RUU again. The update process will then continue.
Note: At this stage, the Wince is destroyed; instead, it is in upgrade mode.
ERROR [300] : INVALID UPDATE TOOL
This error message will appear when you use the incorrect RUU version to upgrade.
ERROR [330] : ROM IMAGE ERROR
This error message will appear when you use the incorrect RUU to upgrade and the image file size is larger than the Flash ROM size. In this case, download the correct RUU version to upgrade.
Click to expand...
Click to collapse
To Clarify: Whenever I went to upgrade my 85' to a different ROM, it wouldn't recognize my bootloader, and then after selecting any of the options, it would give the "ERROR [206]" message and fail miserably with any rom.
What I did to correct it was this: On the "official release" whenever I went to upgrade the ROM, the 85' would show a message at the bottom, the same as any "Notification" would giving me the option to either "confirm" or "dismiss". I did not notice the messages up until it caught my attention out of the corner of my eye on the very last attempt. The messages would quickly appear and disappear, so when the time came and it stated:
Current Rom: 3.25.###.###
Upgrade: 1.##.###
I had to press a confirm notification to continue on or I would get the "206" error message. The quote posted by Binyo is correct, but it does not apply in my situation.
ERROR [206] : MEMORY ALLOCATION
ERROR [280] : UPDATE ERROR
When you see any of these error messages, close other running programs on the computer and run RUU again.
Although that may be true that some applications may interfere with the upgrade process, I had turned off all applications and killed any services during this process.

ERROR [328] : INVALID COMMAND when upgread to sprint ROM

Hi,
I am trying to upgrade the official sprint ROM on HTC Touch (RUU_PPST_Vogue_SPRINT_WWE_3.03.651.4_2_Radio_3.42.30_AM_NV_2.04_Ship) On Current ROM : 3.02.651.2, Radio : 3.37.15
But I am getting ERROR [328] : INVALID COMMAND
Can somebody plz help me to thru this??
retesh101 said:
Hi,
I am trying to upgrade the official sprint ROM on HTC Touch (RUU_PPST_Vogue_SPRINT_WWE_3.03.651.4_2_Radio_3.42.30_AM_NV_2.04_Ship) On Current ROM : 3.02.651.2, Radio : 3.37.15
But I am getting ERROR [328] : INVALID COMMAND
Can somebody plz help me to thru this??
Click to expand...
Click to collapse
Have you called Sprint to ask about this? Since your doing the official ROM update, they should have an answer for you.
You may want to try using a different pc. I got the same screen several times on my desktop. Tried it on my laptop and it worked just fine.
I’ve been able to resolve this on more than 1 occasion, I was able to resolve it by doing the following.
1. Create a new Windows Login/Profile with admin rights and a password.
2. Restart the computer
3. Login to the newly created windows account profile.
4. Place the device into boot loader (Tri-Color screen) you can do this by doing the following [Press and hold both the power button and the camera button, then press the reset button at the bottom]
5. Once the device is in boot loader mode (Tri-Color screen) plug the device into the PC you will notice that the bottom will change from “serial” to “USB”.
6. Once plugged in, download the official ROM update again from HTC’s website (Make sure you hit save and not run) then save it to the desktop so you know where it is at.
7. Once the download has completed run the ROM update again.

List of ERRORs, update firmware

I can't post in developer forum yet....
u ERROR [202, 204] : CONNECTION
This error message will appear when the device is not connected to ActiveSync correctly. Make sure you properly connect the device to the PC through ActiveSync before running RUU.
u ERROR [260] : CONNECTION
This error occurs when there is an “open port error” before upgrading the CE ROM image.
Solution: You can reset the device and run RUU again. If you still encounter an “OPEN PORT ERROR” again, reset your computer and try again.
u ERROR [206] : MEMORY ALLOCATION
u ERROR [280] : UPDATE ERROR
When you see any of these error messages, close other running programs on the computer and run RUU again.
u ERROR [208] : FILE OPEN
u ERROR [210] : FILE READ
These error messages indicate that RUU lacks certain important files and cannot continue with the update. Please get the complete RUU package again.
u ERROR [212] : FILE CREATE
u ERROR [214] : FILE WRITE
u ERROR [222, 224] : DEVICE NOT RESPONDING
These error messages will appear when remote access control has failed. Check the ActiveSync connection and try running RUU again.
u ERROR [220] : MAIN BATTERY POWER
This error message will appear when the device’s battery power is not sufficient. Although RUU will instruct you to plug in the AC adapter, it still has to make sure that your device has enough power to upgrade the radio. (Even when you plug in the AC adapter, the device is unable to charge the battery when it is upgrading the radio).
u ERROR [238] : FILE READ
This error message may appear when, for some unknown reason, the ROM image on the Mobile Device is corrupt. Download the whole RUU and try again.
u ERROR [240] : FILE OPEN
When this error message appears, check whether the downloaded image is placed in the directory of RUU. If, for some unknown reason, you find that the ROM image is not located in the RUU folder, you have to download the RUU and retry again.
u ERROR [242] : INVALID LANGUAGE
u ERROR [244] : INVALID MODEL ID
u ERROR [294] : INVALID VENDER ID
u ERROR [296] : UPGRADE ONLY
One of these error messages will appear when you use the wrong RUU to do the upgrade. RUU will check if the Model ID and Language ID are compatible with the device. Make sure you use the appropriate RUU tool to upgrade.
u ERROR [246] : DEVICE NOT RESPONDING
This error message indicates that RUU cannot start the update process. Please contact your service provider for assistance.
u ERROR [262, 276, 284, 302] : UPDATE ERROR
This error occurs during the CE ROM code upgrade process.
Solution: If this happens, you can just soft-reset the device and run RUU again. The update process will then continue.
Note: At this stage, the Wince is destroyed; instead, it is in upgrade mode.
u ERROR [300] : INVALID UPDATE TOOL
This error message will appear when you use the incorrect RUU version to upgrade.
u ERROR [330] : ROM IMAGE ERROR
This error message will appear when you use the incorrect RUU to upgrade and the image file size is larger than the Flash ROM size. In this case, download the correct RUU version to upgrade.
well,thanks man for the sharing
valuable information may be usefull just in case
I always end up with 270 error.

OTA update fails at 25%

I have a stock unrooted N7100. I was notified of a software update yesterday, and chose to install it. The phone rebooted, got to 25%, then displayed a dead Android with the message "Error", and rebooted. If I go to the Software Update screen I get this message:
"Failed to update firmware. Try again using PC software (Kies) or visit a Samsung service centre"
The phone is currently running Android 4.4.2 - build KOT49H.N7100XXUFNE1.
Has anyone else encountered this? If so, did you have any luck using Kies?
I've tried to install Kies on my Acer Switch 10V Windows 10 laptop and got this error:
"The application has failed to start because its side-by-side configuration is incorrect. Please see the application event log or use the command line sxstrace.exe tool for more detail."
???
itm said:
I've tried to install Kies on my Acer Switch 10V Windows 10 laptop and got this error:
"The application has failed to start because its side-by-side configuration is incorrect. Please see the application event log or use the command line sxstrace.exe tool for more detail."
???
Click to expand...
Click to collapse
download the latest firmware for N7100 from sammobile.com or samsung-firmware.org and flash it with Odin application for PC while putting the phone into download mode..
no need for kies.

Categories

Resources