manipulator works fine but I see no IMEI - Upgrading, Modifying and Unlocking

Hi folks. complete.. newby here and really struggling to understand some of this stuff. I have done the soft reset, connected the cable, ran manipulator, however all I see is two entries Statsu: Ready and SID lock <none>
there is no other info displayed at all? The radio version is 3.25.01
any idea why I cant see or reset the EMEI?
thanks

Related

How to get into Bootloader

Hi there!
What key combination gets me into the bootloader?
I've been wondering and searching for a way to upgrade my MDA pro rom. (searching for hours on xda, google and a lot of other specialized sites. Turned out to be dead ends! FRUSTRATING!
I'va had a Qtek S100 before. There was a way to get into the bootloader. And there is a way into the bootloader for the Universal to! YES!
But when i try to push the buttons
on/of
Camera
reset button
i cant get in!
button 1 and 2
reset
the same problem.
I get as far as the pres 0 or X for factory default and exit.
Who can help me? I have the no_id upgrade utility and the ROM ready.
Was there a UUL file which i had to edit before using this upgrade method?
I hope there wil be a good tutorial for this just like the one i have used to upgrade my S100 to an orange rom. (worked great!)
Can anyone help me please
Its BACKLIGHT BUTTON + POWER BUTTON + RESET HOLE
It's better to do this without the SIM and Memory Card connected. Disconnect also the USB Sync Cable.
After entering bootloader, you will see SERIAL written on the screen but the screen has no backlight so you have to look hard.
Then when you plug the Sync Cable, the SERIAL will change to USB then you can run the NoID to update.
Remember the NoID has to be run twice in a row as the first time usually solicits an ID Country error
It Works
Thanks Jorge!
Just those keystrokes helped me a lot. It works just fine and it took me only one run to Initiate the upgrading.
Thanks a lot!
I followed your advice and removed the SD and the phone card.
Yes! now i can experiment with these ROMS.
First Jasjar, later O2 and hoping for the best roms with the best programs.(hoping to find a messenger cab file in the jasjar rom)
As I am planning to do the same, Try all the variants of the ROM's, could you inform me what are the good and bad points of all the different ROM's you used and which did you decide to use finally.
Thanks
HELP !!!!
I turn on my Qtek 9000 and i see SERIAL written and the screen but the screen has no backlight.
How can I boot my Qtek 9000 again without this SERIAL mode ????
Best Regards
Hi Ecraseur,
if You did not do anything else (no upgrading), try ColdReset : Power-switch + Reset hole.
Ruud
If we can boot from Serial/USB is it possible to boot from Mini SD? I'm toying with the idea that by using a Linux Live Disk content on a Mini SD it may be possible to boot into a virtual Linux environment? I know it's going to be uber slow and may not even work but I thought it may be worth a look?
If a Mini SD boot isn't possible do you think it'd work to have one of the smaller USB bootable Linux flavours as the USB boot for the HTC Wizard etc?

I've tried upgrading my JasJar with Xda_Exec_Upgrade_v1.30

I guys, I've tried upgrading my JasJar with Xda_Exec_Upgrade_v1.30.162, using MaUpgradeUt_noID and when update was complete I cannot load my JasJar anymore. I am using hard reset, but when choosing "0" off the boot screen - noting happens and screeen remains black.
Can someone please help me with this issue?
Thanks a lot in advance,
Best regards,
Stazik
Try reflashing it again. If it does not work, try reflashing back to the i-Mate ROM.
Whats the version of your bootloader (the screen with serial at the top changing to usb when plugged into usb)? If it is 0.56 or something else below 0.6 thats an already known problem.
I had similar problems with my O2 upgrade.
Try:
- Turn off USB in ActiveSync
- Hold Power/Light and press reset button
- Run the upgrade again
Thank you very much for help and support, guys!
When I try flashing my JasJar with Bootloader update or JASJAR_WWE_13076_164_10900_wwe_ship I get the same error message: Error 101 Connection Error. And also when I disable ActiveSync USB and plug my Jasjar into USB - I get a message from windows saying the device was not recognized...
The only I can get from JasJar is a black screen, except when I press two soft buttons and reset - that gives me a screen with 0 and x to choose. Neither of choices helps thou.
Any help is appreciated. Thanks a lot.
you didnt answer the question re the boot loader number.
when your screen is grey or starting to reset, there are numbers on the screen. what are they.
if it is less that 0.6 your in trouble and assistance is different to if your boot loader is 1.0 or similar.
My screen doesn't change from gray except when I do hard reset. And then I hit two buttons and reset, then press 0 the message Clearing now appears and then everything returns to gray again.
How can I tell the version of bootloader in this case?
Thank you in advance!
they are hard to see, if the screen is grey, the numbers are black.
f the screen is blue/coloured, the nmbers are probably red.
Thanks for help guys,
I brought my JasJar for service today, somehow they were able to put older ROM in there. Now I've upgraded bootloader, hopefully newest ROM from i-mate going to fit without problems )
Well I've killed my Jasjar upgrading I was installing the bootloader update. It sat there saying "Checking information on your device" for about 30 minutes after the update started (notes said it would take 10 so I figured something was amiss - disconnected & rebooted my PC.
Now when I turn the Jasjar on I get the USB/Serial screen referred to above and (good news I figure) it has v1.00 at the bottom. How do I fix this?
TIA
Sheesh. I did a search (I know I should have done that first) and found the answer here
Took a while to find a copy of mtty to download, but found that at http://buzzdev.net
Once I'd done the Set 14 0 and tried the boot loader update again it took seconds so something definitely went wrong the first time.

Newbie but I hope not !!! help btw !!!

I own a new blue angel...called by O2 II's
So, after i read ,again,and again...I have successed enter boot loader.
With white screen it's shown the version 2.07 and the line at the top "Serial"
(uhm, i use WM2003SE as the original pda when i purchase)
Ok, the problem now is, i can't flash anyrom (in Wiki and any rom i found)
After the line appear "Don't plug cable or craddle of ...." it's seem to verifie it's self... and then the line appear again "this tool is not support for this device".....and some error like that.
I was totally confused, how i made the thing go wrong? or just i missed something???
i make a soft reset, then hard reset and then 3 button together to get the white screen with no light, still see words such as: serial, version 2.0.7...
When i plug the usb cable , then the serial change into USB as usual.
As my experience,( Dopod810 and Qtek S200) everything is normal...
One problem too, i can't connect to PC with activsync (i tried any versions as possible)but itself avaiable on Boot loader...
All you understand what happen with me???
Please help me out of this. I want my Blue Angel is not the worst i got ...(i think it's possible go up to wm6???)
Finally, thanks you all for listening( reading this topic)
Yep, Happened to me too. Heres the fix.
The regular WM6 exe will give you an error everytime with the O2 IIs. Finally I printed out the WM6 directions, and also the Blue Angel for beginners and some other threads and found the answer.
You are in the right place (stuck in bootloader that is). Now you should be ready to load the OS. In the Upgrade folder you will find:
"MaUpgradeUt_noID.exe"
Run it and you will see the progress bars on the Windows screen and the dark XDA screen. Don't bother it - allow it to complete.
After it completed, I was unable to restart, soft reset, hard reboot. I think I actually had to take the battery off. When I powered it again I saw the Color Bars and knew it was good.
Good luck, Be careful. Try to be calm. I know when I was stuck in between Roms I was close to being a nervous wreck.
erh, one more message when i fkash rom...
This MaUpgradeUT novid erh something like this but this
" This tool is not support for my device" or somehow ...
I think i really stuck...
when itself verifie version of rom , i can't see both version appear on windows.
ie : version rom which is in PDA and version of rom which is in the OS i next to flash(want to flash).
So Confused . Anyway, thank for helping !!!
You are close!
Yea,
I Kept getting that too. Couldn't see both versions. Got a couple of different error messages. you are right where I was. you've got to find the upgrade exe. in one of the folders. My IIs was stuck in bootloader and I started that upgrade and it skips checking the IIs first and just begins to xfer the data.

4 color bands at boot

Hi,
I have a problem with my QTek 9090.
when i want to hard reset it, (power, record, camera and reset) it just displayed the 4 colored bands and stuck here.
how can i restore the normal booting sequence ?
thx.
this is normal, no problem. OS is kichen, no orginal. My Qtek work perfect WM6. Thanks Helmi!
so what should i do because it is block on this stupid 4 colored bands screen...
hard and soft reset do not help.
are you sure you have chosen No/Yes/Yes to clean the registy hive and format the storage at hard reset?
have you pressed the Mail Button to execute the instruction?
being stuck at the 4color screen is a common glitch in wm6 upgrading but nothing serious, that's because even though you flashed the ROM, your storage still has the files of your OLD Os (ex. WM2003).
you have to format the storage to have a fresh and working OS.
the problem is that i did not get any message on screen to which i can answer yes or no :-(
i effectively read some article in this forum about such step, but my Qtek 9090 did not propose me something like that !
:-(
i tried the steps you posted in http://forum.xda-developers.com/showpost.php?p=1603200&postcount=8
but the menu is never displayed :-(
oh... ok.
try pressing Camera + Record... before you stick the Soft Reset.
hold them until you see the menu.
if that doesnt work. then maybe one of the required button is failing.
good luck!
unfortunatelly, it does not work :-(
this is making me crazy...
try searching for MMTY hard reset. that's probably the thing that you need.
i did not find anything about MMTY and hard reset...
:-(
any additional help would be very appreciated
You would find you get a better response if you explain what rom it was that you were installing when this happened,was the rom for your device and did it complete fully?
scousemartin is right... we need details.
about MTTY ok...
here's a link about MTTY on Hermes Bootloader... some of its commands are general and can be used on BA with care.
look for something specific to your problem
i.e. Task 28 to format your DOC.

[Q] Bricked Artemis - can enter bootloader

Hello,
a friend of mine probably bricked his Artemis. He tried to flash, but did not HSPL first. Now the device can enter only bootloader. I tried many USPLs, MTTY, micro SD but nothing worked.
The version of SPL is 1.14, active sync does not go green after connecting, but if I try to flash, it is recognized and returns Error 300. I guess I need the original ROM, but it was in czech and I cannot find it anywhere.
Any ideas are very welcome.
Thanks in advance.
parizek said:
Hello,
a friend of mine probably bricked his Artemis. He tried to flash, but did not HSPL first. Now the device can enter only bootloader. I tried many USPLs, MTTY, micro SD but nothing worked.
The version of SPL is 1.14, active sync does not go green after connecting, but if I try to flash, it is recognized and returns Error 260. I guess I need the original ROM, but it was in czech and I cannot find it anywhere.
Any ideas are very welcome.
Thanks in advance.
Click to expand...
Click to collapse
for SPL Artemis you can try this and to l his official ROM you can look at -> http://www.shipped-roms.com/index.php?category=windows mobile&model = Artemis​ but first try to him that your friend's device hardreset !! like this way :To perform a hard reset
Press and hold the Left SOFT KEY and the Right SOFT KEY, and at the same time, use the stylus to press the RESET button at the lower left side of your device.
Release the stylus, but continue pressing the two soft key buttons. Release them only when you see the following message on your device screen: “Press Send to restore manufacturer default, or press other keys to cancel.“
Press on your device. Warning! Your device will be set back to factory default settings. Please ensure any additional installed programs and/or user data have been backed up before a hard reset is performed.
thanks for ideas. HR cannot be made - returns error like "cannot format partition".
On the shipped ROMs site I cannot download anything - it only says something about redirection on ppc geeks
Here I attach the screen, what I get after trying to flash..
...
only the original rom will bring your device back to life.
whats your red numbers and letters at device start-up?
I can get only to bootloader, so the IPL : 1.14.0001 and SPL 1.14.0000 , that's all I can get
hmm, after a communication with official HTC servise in Czech Republic I got the number of original ROM and successfully downloaded it.
But still the same issue. Is it possible, that Bootloader is corrupted ? The guy told me that it is the only possible cause, if this ROM does not work
...
Try this original rom..
The bootloader of this rom matches yours..
(1.14.0000)
1. Put device into bootloader
2. Connect device to PC
3. Run the RUU
4(a). If this does not work, then you are stuck in the mud..
4(b). If that original rom does work, then click here for USPL 1.11.CMON
Good luck!
Rn
Hi,
thanks man for all the ideas. Unfortunately the ROM you are hyperlinkinkg I have already tried with no success. I have given it maximum, now I am giving it up.
Thanks for your patient help.
p
ME to in same problem plz help IPL 3.04.0001 and SPL 3.04.0000

Categories

Resources